| Age | Commit message (Collapse) | Author |
|---|
|
This patch fixes bug where early se_cmd exceptions that occur
before backend execution can result in use-after-free if/when
a subsequent ABORT_TASK occurs for the same tag.
Since an early se_cmd exception will have had se_cmd added to
se_session->sess_cmd_list via target_get_sess_cmd(), it will
not have CMD_T_COMPLETE set by the usual target_complete_cmd()
backend completion path.
This causes a subsequent ABORT_TASK + __target_check_io_state()
to signal ABORT_TASK should proceed. As core_tmr_abort_task()
executes, it will bring the outstanding se_cmd->cmd_kref count
down to zero releasing se_cmd, after se_cmd has already been
queued with error status into fabric driver response path code.
To address this bug, introduce a CMD_T_PRE_EXECUTE bit that is
set at target_get_sess_cmd() time, and cleared immediately before
backend driver dispatch in target_execute_cmd() once CMD_T_ACTIVE
is set.
Then, check CMD_T_PRE_EXECUTE within __target_check_io_state() to
determine when an early exception has occured, and avoid aborting
this se_cmd since it will have already been queued into fabric
driver response path code.
Reported-by: Donald White <dew@datera.io>
Cc: Donald White <dew@datera.io>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a potential end-less loop during QUEUE_FULL,
where cmd->se_tfo->write_pending() callback fails repeatedly
but __transport_wait_for_tasks() has already been invoked to
quiese the outstanding se_cmd descriptor.
To address this bug, this patch adds a CMD_T_STOP|CMD_T_ABORTED
check within transport_write_pending_qf() and invokes the
existing se_cmd->t_transport_stop_comp to signal quiese
completion back to __transport_wait_for_tasks().
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: Potnuri Bharat Teja <bharat@chelsio.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
With the recent addition of transport_check_aborted_status() within
transport_generic_request_failure() to avoid sending a SCSI status
exception after CMD_T_ABORTED w/ TAS=1 has occured, it introduced
a COMPARE_AND_WRITE early failure regression.
Namely when COMPARE_AND_WRITE fails and se_device->caw_sem has
been taken by sbc_compare_and_write(), if the new check for
transport_check_aborted_status() returns true and exits,
cmd->transport_complete_callback() -> compare_and_write_post()
is skipped never releasing se_device->caw_sem.
This regression was originally introduced by:
commit e3b88ee95b4e4bf3e9729a4695d695b9c7c296c8
Author: Bart Van Assche <bart.vanassche@sandisk.com>
Date: Tue Feb 14 16:25:45 2017 -0800
target: Fix handling of aborted failed commands
To address this bug, move the transport_check_aborted_status()
call after transport_complete_task_attr() and
cmd->transport_complete_callback().
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a bug during QUEUE_FULL where transport_complete_qf()
calls transport_complete_task_attr() after it's already been invoked
by target_complete_ok_work() or transport_generic_request_failure()
during initial completion, preceeding QUEUE_FULL.
This will result in se_device->simple_cmds, se_device->dev_cur_ordered_id
and/or se_device->dev_ordered_sync being updated multiple times for
a single se_cmd.
To address this bug, clear SCF_TASK_ATTR_SET after the first call
to transport_complete_task_attr(), and avoid updating SCSI task
attribute related counters for any subsequent calls.
Also, when a se_cmd is deferred due to ordered tags and executed
via target_restart_delayed_cmds(), set CMD_T_SENT before execution
matching what target_execute_cmd() does.
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Conflicts:
include/linux/compiler-clang.h
include/linux/compiler-gcc.h
include/linux/compiler-intel.h
include/uapi/linux/stddef.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Add a jump target so that a bit of exception handling can be better reused
at the end of this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Certain behavior of the initiator can cause the target driver to
send both a reject and a SCSI response. If that happens two
target_put_sess_cmd() calls will occur without the command having
been removed from conn_cmd_list. In other words, conn_cmd_list
will get corrupted once the freed memory is reused. Although the
Linux kernel can detect list corruption if list debugging is
enabled, in this case the context in which list corruption is
detected is not related to the context that caused list corruption.
Hence add WARN_ON() statements that report the context that is
causing list corruption.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Avoid that cmd->se_cmd.se_tfo is read after a command has already been
freed.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Change the type of the last two arguments from u8 * into const void *
and void * respectively such that the u8 * casts can be left out
from the callers. This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Since hdr->offset is a big endian number, convert it to CPU endian
before printing it.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The constant OFFLOAD_BUF_SIZE is defined twice - once in
iscsi_target_seq_pdu_list.c and once in iscsi_target_erl1.c. Since
that constant is not used in the former source file, remove its
definition from that source file.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Since all transput_put_cmd() does is to call target_put_sess_cmd(),
inline transport_put_cmd() into its callers. Leave out the BUG_ON()
statement because if cmd->se_tfo == NULL then cmd->cmd_kref is 0
and kref_put() will complain anyway. Notes:
- transport_init_se_cmd() initializes both .se_tfo and .cmd_kref.
- The only target driver that does not call transport_init_se_cmd()
for all commands is the iSCSI target driver. See also
iscsi_target_rx_opcode().
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Varun Prakash <varun@chelsio.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch avoids that sparse reports the following warning:
drivers/target/target_core_configfs.c:2267:33: warning: symbol 'target_core_dev_item_ops' was not declared. Should it be static?
Fixes: c17cd24959cd ("target/configfs: Kill se_device->dev_link_magic")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
If cmd_time_out != 0, then tcmu_queue_cmd_ring could end up
sleeping waiting for ring space, timing out and then returning
failure to lio, and tcmu_check_expired_cmd could also detect
the timeout and call target_complete_cmd on the cmd.
This patch just delays setting up the deadline value and adding
the cmd to the udev->commands idr until we have allocated ring
space and are about to send the cmd to userspace.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
TCM_OUT_OF_RESOURCES is getting translated to
TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE which seems like a heavy
error when we just cannot allocate a resource that may be
allocatable later. This has us translate TCM_OUT_OF_RESOURCES
to SAM_STAT_TASK_SET_FULL instead.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
A sufficiently long Unit Serial string, dbroot path, and/or ALUA target
portal group name may result in truncation of the ALUA state file path
prior to usage. Fix this by using kasprintf() instead.
Fixes: fdddf932269a ("target: use new "dbroot" target attribute")
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
If an LIO backstore is configured with a sufficiently long Unit Serial
string, alongside a similarly long dbroot path, then a truncated
Persistent Reservation APTPL state file path will be used. This
truncation can unintentionally lead to two LUs with differing serial
numbers sharing PR state file.
Fixes: fdddf932269a ("target: use new "dbroot" target attribute")
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
If DDP is programmed for a WRITE cmd and data out
timer gets expired then abort the TCP connection
before freeing the cmd to avoid any possibility of
DDP after freeing the cmd.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Currently netlink command reply support option
(TCMU_ATTR_SUPP_KERN_CMD_REPLY) can be enabled only on module
scope. Because of that, once an application enables the netlink
command reply support, all applications using target_core_user.ko
would be expected to support the netlink reply. To make matters worse,
users will not be able to add a device via configfs manually.
To fix these issues, this patch adds an option to make netlink command
reply disabled on each device through configfs. Original
TCMU_ATTR_SUPP_KERN_CMD_REPLY is still enabled on module scope to keep
backward-compatibility and used by default, however once users set
nl_reply_supported=<NAGATIVE_VALUE> via configfs for a particular
device, the device disables the netlink command reply support.
Signed-off-by: Kenjiro Nakayama <nakayamakenjiro@gmail.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch makes a tiny change that using TCMU_DEV in
tcmu_cmd_time_out_show so it is consistent with other functions.
Signed-off-by: Kenjiro Nakayama <nakayamakenjiro@gmail.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Before the nl REMOVE msg has been sent to the userspace, the ring's
and other resources have been released, but the userspace maybe still
using them. And then we can see the crash messages like:
ring broken, not handling completions
BUG: unable to handle kernel paging request at ffffffffffffffd0
IP: tcmu_handle_completions+0x134/0x2f0 [target_core_user]
PGD 11bdc0c067
P4D 11bdc0c067
PUD 11bdc0e067
PMD 0
Oops: 0000 [#1] SMP
cmd_id not found, ring is broken
RIP: 0010:tcmu_handle_completions+0x134/0x2f0 [target_core_user]
RSP: 0018:ffffb8a2d8983d88 EFLAGS: 00010296
RAX: 0000000000000000 RBX: ffffb8a2aaa4e000 RCX: 00000000ffffffff
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000220
R10: 0000000076c71401 R11: ffff8d2e76c713f0 R12: ffffb8a2aad56bc0
R13: 000000000000001c R14: ffff8d2e32c90000 R15: ffff8d2e76c713f0
FS: 00007f411ffff700(0000) GS:ffff8d1e7fdc0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffffffffd0 CR3: 0000001027070000 CR4:
00000000001406e0
Call Trace:
? tcmu_irqcontrol+0x2a/0x40 [target_core_user]
? uio_write+0x7b/0xc0 [uio]
? __vfs_write+0x37/0x150
? __getnstimeofday64+0x3b/0xd0
? vfs_write+0xb2/0x1b0
? syscall_trace_enter+0x1d0/0x2b0
? SyS_write+0x55/0xc0
? do_syscall_64+0x67/0x150
? entry_SYSCALL64_slow_path+0x25/0x25
Code: 41 5d 41 5e 41 5f 5d c3 83 f8 01 0f 85 cf 01 00
00 48 8b 7d d0 e8 dd 5c 1d f3 41 0f b7 74 24 04 48 8b
7d c8 31 d2 e8 5c c7 1b f3 <48> 8b 7d d0 49 89 c7 c6 07
00 0f 1f 40 00 4d 85 ff 0f 84 82 01 RIP:
tcmu_handle_completions+0x134/0x2f0 [target_core_user]
RSP: ffffb8a2d8983d88
CR2: ffffffffffffffd0
And the crash also could happen in tcmu_page_fault and other places.
Signed-off-by: Zhang Zhuoyu <zhangzhuoyu@cmss.chinamobile.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Need to release the param_list for tpg in iscsi_release_discovery_tpg
function, this is also required before the iscsit_load_discovery_tpg
function exits abnormally.
Signed-off-by: tangwenji <tang.wenji@zte.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
tpg must free when call core_tpg_register() return fail
Signed-off-by: tangwenji <tang.wenji@zte.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
When is pr_reg->isid_present_at_reg is false,this function should return.
This fixes a regression originally introduced by:
commit d2843c173ee53cf4c12e7dfedc069a5bc76f0ac5
Author: Andy Grover <agrover@redhat.com>
Date: Thu May 16 10:40:55 2013 -0700
target: Alter core_pr_dump_initiator_port for ease of use
Signed-off-by: tangwenji <tang.wenji@zte.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The match_token function does not recognize the option 'l',
so that both the mapped_lun and target_lun parameters
can not be resolved correctly.
And parsed u64-type parameters should use match_u64().
(Use %u instead of %s for Opt_mapped_lun + Opt_target_lun - nab)
Signed-off-by: tangwenji <tang.wenji@zte.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
If a PERSISTENT RESERVE OUT command with a REGISTER service action or a
REGISTER AND IGNORE EXISTING KEY service action or REGISTER AND MOVE
service action is attempted, but there are insufficient device server
resources to complete the operation, then the command shall be terminated
with CHECK CONDITION status, with the sense key set to ILLEGAL REQUEST,and
the additonal sense code set to INSUFFICIENT REGISTRATION RESOURCES.
Signed-off-by: tangwenji <tang.wenji@zte.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: tangwenji <tang.wenji@zte.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
When at least two initiators register pr on the same LUN,
the target returns the exception data due to buffer offset
error, therefore the initiator executes command 'sg_persist -s'
may cause the initiator to appear segfault error.
This fixes a regression originally introduced by:
commit a85d667e58bddf73be84d1981b41eaac985ed216
Author: Bart Van Assche <bart.vanassche@sandisk.com>
Date: Tue May 23 16:48:27 2017 -0700
target: Use {get,put}_unaligned_be*() instead of open coding these functions
Signed-off-by: tangwenji <tang.wenji@zte.com.cn>
Cc: stable@vger.kernel.org # 4.13+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The target system kernel crash when the initiator executes
the sg_persist -A command,because of the second argument to
be set to NULL when core_tmr_lun_reset is called in
core_scsi3_pro_preempt function.
This fixes a regression originally introduced by:
commit 51ec502a32665fed66c7f03799ede4023b212536
Author: Bart Van Assche <bart.vanassche@sandisk.com>
Date: Tue Feb 14 16:25:54 2017 -0800
target: Delete tmr from list before processing
Signed-off-by: tangwenji <tang.wenji@zte.com.cn>
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The function fd_execute_unmap() in target_core_file.c calles
ret = file->f_op->fallocate(file, mode, pos, len);
Some filesystems implement fallocate() to return error if
length is zero (e.g. btrfs) but according to SCSI Block
Commands spec UNMAP should return success for zero length.
Signed-off-by: Jiang Yi <jiangyilism@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Includes a fix for correcting an
on-stack timer usage.
Cc: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Jiang Yi <jiangyilism@gmail.com>
Cc: Varun Prakash <varun@chelsio.com>
Cc: linux-scsi@vger.kernel.org
Cc: target-devel@vger.kernel.org
Reviewed-and-Tested-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Move timer initialization from before add_timer() to the context
where the containing object is initialized. Use setup_timer() and
mod_timer() instead of open coding these. Use 'jiffies' instead
of get_jiffies_64() when calculating expiry times because expiry
times have type unsigned long, just like 'jiffies'.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: David Disseldorp <ddiss@suse.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
to READ_ONCE()/WRITE_ONCE()
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Make these structures const as they are either passed to the functions
having the argument as const or stored as a reference in the "ci_type"
const field of a config_item structure.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more set_fs removal from Al Viro:
"Christoph's 'use kernel_read and friends rather than open-coding
set_fs()' series"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: unexport vfs_readv and vfs_writev
fs: unexport vfs_read and vfs_write
fs: unexport __vfs_read/__vfs_write
lustre: switch to kernel_write
gadget/f_mass_storage: stop messing with the address limit
mconsole: switch to kernel_read
btrfs: switch write_buf to kernel_write
net/9p: switch p9_fd_read to kernel_write
mm/nommu: switch do_mmap_private to kernel_read
serial2002: switch serial2002_tty_write to kernel_{read/write}
fs: make the buf argument to __kernel_write a void pointer
fs: fix kernel_write prototype
fs: fix kernel_read prototype
fs: move kernel_read to fs/read_write.c
fs: move kernel_write to fs/read_write.c
autofs4: switch autofs4_write to __kernel_write
ashmem: switch to ->read_iter
|
|
Pull block layer updates from Jens Axboe:
"This is the first pull request for 4.14, containing most of the code
changes. It's a quiet series this round, which I think we needed after
the churn of the last few series. This contains:
- Fix for a registration race in loop, from Anton Volkov.
- Overflow complaint fix from Arnd for DAC960.
- Series of drbd changes from the usual suspects.
- Conversion of the stec/skd driver to blk-mq. From Bart.
- A few BFQ improvements/fixes from Paolo.
- CFQ improvement from Ritesh, allowing idling for group idle.
- A few fixes found by Dan's smatch, courtesy of Dan.
- A warning fixup for a race between changing the IO scheduler and
device remova. From David Jeffery.
- A few nbd fixes from Josef.
- Support for cgroup info in blktrace, from Shaohua.
- Also from Shaohua, new features in the null_blk driver to allow it
to actually hold data, among other things.
- Various corner cases and error handling fixes from Weiping Zhang.
- Improvements to the IO stats tracking for blk-mq from me. Can
drastically improve performance for fast devices and/or big
machines.
- Series from Christoph removing bi_bdev as being needed for IO
submission, in preparation for nvme multipathing code.
- Series from Bart, including various cleanups and fixes for switch
fall through case complaints"
* 'for-4.14/block' of git://git.kernel.dk/linux-block: (162 commits)
kernfs: checking for IS_ERR() instead of NULL
drbd: remove BIOSET_NEED_RESCUER flag from drbd_{md_,}io_bio_set
drbd: Fix allyesconfig build, fix recent commit
drbd: switch from kmalloc() to kmalloc_array()
drbd: abort drbd_start_resync if there is no connection
drbd: move global variables to drbd namespace and make some static
drbd: rename "usermode_helper" to "drbd_usermode_helper"
drbd: fix race between handshake and admin disconnect/down
drbd: fix potential deadlock when trying to detach during handshake
drbd: A single dot should be put into a sequence.
drbd: fix rmmod cleanup, remove _all_ debugfs entries
drbd: Use setup_timer() instead of init_timer() to simplify the code.
drbd: fix potential get_ldev/put_ldev refcount imbalance during attach
drbd: new disk-option disable-write-same
drbd: Fix resource role for newly created resources in events2
drbd: mark symbols static where possible
drbd: Send P_NEG_ACK upon write error in protocol != C
drbd: add explicit plugging when submitting batches
drbd: change list_for_each_safe to while(list_first_entry_or_null)
drbd: introduce drbd_recv_header_maybe_unplug
...
|
|
Make the position an in/out argument like all the other read/write
helpers and and make the buf argument a void pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch fixes a generate_node_acls = 1 + cache_dynamic_acls = 0
regression, that was introduced by
commit 01d4d673558985d9a118e1e05026633c3e2ade9b
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Wed Dec 7 12:55:54 2016 -0800
which originally had the proper list_del_init() usage, but was
dropped during list review as it was thought unnecessary by HCH.
However, list_del_init() usage is required during the special
generate_node_acls = 1 + cache_dynamic_acls = 0 case when
transport_free_session() does a list_del(&se_nacl->acl_list),
followed by target_complete_nacl() doing the same thing.
This was manifesting as a general protection fault as reported
by Justin:
kernel: general protection fault: 0000 [#1] SMP
kernel: Modules linked in:
kernel: CPU: 0 PID: 11047 Comm: iscsi_ttx Not tainted 4.13.0-rc2.x86_64.1+ #20
kernel: Hardware name: Intel Corporation S5500BC/S5500BC, BIOS S5500.86B.01.00.0064.050520141428 05/05/2014
kernel: task: ffff88026939e800 task.stack: ffffc90007884000
kernel: RIP: 0010:target_put_nacl+0x49/0xb0
kernel: RSP: 0018:ffffc90007887d70 EFLAGS: 00010246
kernel: RAX: dead000000000200 RBX: ffff8802556ca000 RCX: 0000000000000000
kernel: RDX: dead000000000100 RSI: 0000000000000246 RDI: ffff8802556ce028
kernel: RBP: ffffc90007887d88 R08: 0000000000000001 R09: 0000000000000000
kernel: R10: ffffc90007887df8 R11: ffffea0009986900 R12: ffff8802556ce020
kernel: R13: ffff8802556ce028 R14: ffff8802556ce028 R15: ffffffff88d85540
kernel: FS: 0000000000000000(0000) GS:ffff88027fc00000(0000) knlGS:0000000000000000
kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
kernel: CR2: 00007fffe36f5f94 CR3: 0000000009209000 CR4: 00000000003406f0
kernel: DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
kernel: DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
kernel: Call Trace:
kernel: transport_free_session+0x67/0x140
kernel: transport_deregister_session+0x7a/0xc0
kernel: iscsit_close_session+0x92/0x210
kernel: iscsit_close_connection+0x5f9/0x840
kernel: iscsit_take_action_for_connection_exit+0xfe/0x110
kernel: iscsi_target_tx_thread+0x140/0x1e0
kernel: ? wait_woken+0x90/0x90
kernel: kthread+0x124/0x160
kernel: ? iscsit_thread_get_cpumask+0x90/0x90
kernel: ? kthread_create_on_node+0x40/0x40
kernel: ret_from_fork+0x22/0x30
kernel: Code: 00 48 89 fb 4c 8b a7 48 01 00 00 74 68 4d 8d 6c 24 08 4c
89 ef e8 e8 28 43 00 48 8b 93 20 04 00 00 48 8b 83 28 04 00 00 4c 89
ef <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 20
kernel: RIP: target_put_nacl+0x49/0xb0 RSP: ffffc90007887d70
kernel: ---[ end trace f12821adbfd46fed ]---
To address this, go ahead and use proper list_del_list() for all
cases of se_nacl->acl_list deletion.
Reported-by: Justin Maggard <jmaggard01@gmail.com>
Tested-by: Justin Maggard <jmaggard01@gmail.com>
Cc: Justin Maggard <jmaggard01@gmail.com>
Cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a bug associated with iscsit_reset_np_thread()
that can occur during parallel configfs rmdir of a single iscsi_np
used across multiple iscsi-target instances, that would result in
hung task(s) similar to below where configfs rmdir process context
was blocked indefinately waiting for iscsi_np->np_restart_comp
to finish:
[ 6726.112076] INFO: task dcp_proxy_node_:15550 blocked for more than 120 seconds.
[ 6726.119440] Tainted: G W O 4.1.26-3321 #2
[ 6726.125045] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 6726.132927] dcp_proxy_node_ D ffff8803f202bc88 0 15550 1 0x00000000
[ 6726.140058] ffff8803f202bc88 ffff88085c64d960 ffff88083b3b1ad0 ffff88087fffeb08
[ 6726.147593] ffff8803f202c000 7fffffffffffffff ffff88083f459c28 ffff88083b3b1ad0
[ 6726.155132] ffff88035373c100 ffff8803f202bca8 ffffffff8168ced2 ffff8803f202bcb8
[ 6726.162667] Call Trace:
[ 6726.165150] [<ffffffff8168ced2>] schedule+0x32/0x80
[ 6726.170156] [<ffffffff8168f5b4>] schedule_timeout+0x214/0x290
[ 6726.176030] [<ffffffff810caef2>] ? __send_signal+0x52/0x4a0
[ 6726.181728] [<ffffffff8168d7d6>] wait_for_completion+0x96/0x100
[ 6726.187774] [<ffffffff810e7c80>] ? wake_up_state+0x10/0x10
[ 6726.193395] [<ffffffffa035d6e2>] iscsit_reset_np_thread+0x62/0xe0 [iscsi_target_mod]
[ 6726.201278] [<ffffffffa0355d86>] iscsit_tpg_disable_portal_group+0x96/0x190 [iscsi_target_mod]
[ 6726.210033] [<ffffffffa0363f7f>] lio_target_tpg_store_enable+0x4f/0xc0 [iscsi_target_mod]
[ 6726.218351] [<ffffffff81260c5a>] configfs_write_file+0xaa/0x110
[ 6726.224392] [<ffffffff811ea364>] vfs_write+0xa4/0x1b0
[ 6726.229576] [<ffffffff811eb111>] SyS_write+0x41/0xb0
[ 6726.234659] [<ffffffff8169042e>] system_call_fastpath+0x12/0x71
It would happen because each iscsit_reset_np_thread() sets state
to ISCSI_NP_THREAD_RESET, sends SIGINT, and then blocks waiting
for completion on iscsi_np->np_restart_comp.
However, if iscsi_np was active processing a login request and
more than a single iscsit_reset_np_thread() caller to the same
iscsi_np was blocked on iscsi_np->np_restart_comp, iscsi_np
kthread process context in __iscsi_target_login_thread() would
flush pending signals and only perform a single completion of
np->np_restart_comp before going back to sleep within transport
specific iscsit_transport->iscsi_accept_np code.
To address this bug, add a iscsi_np->np_reset_count and update
__iscsi_target_login_thread() to keep completing np->np_restart_comp
until ->np_reset_count has reached zero.
Reported-by: Gary Guo <ghg@datera.io>
Tested-by: Gary Guo <ghg@datera.io>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The current logic of calculating sg_nents can fail
if data_offset % PAGE_SIZE is not zero.
For example -
PAGE_SIZE = 4096
data_len = 3072
data_offset = 3072
As per current logic
sg_nents = max(1UL, DIV_ROUND_UP(data_len, PAGE_SIZE));
sg_nents = max(1UL, DIV_ROUND_UP(3072, 4096));
sg_nents = 1
But as data_offset % PAGE_SIZE = 3072 we should skip 3072 bytes
skip = 3K
sg_nents = max(1UL, DIV_ROUND_UP(3K(skip) + 3K(data_len), 4K(PAGE_SIZE));
sg_nents = 2;
This patch fixes this issue by adding skip to data_len.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
In case of multiple text responses iscsi-target
sets both 'F' and 'C' bit for the final text response
pdu, this issue happens because hdr->flags is not
zeroed out before ORing with 'F' bit.
This patch removes the | operator to fix this issue.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
On receiving text request iscsi-target allocates buffer for
payload in iscsit_handle_text_cmd() and assigns buffer pointer
to cmd->text_in_ptr, this buffer is currently freed in
iscsit_release_cmd(), if iscsi-target sets 'C' bit in text
response then it will receive another text request from the
initiator with ttt != 0xffffffff in this case iscsi-target
will find cmd using itt and call iscsit_setup_text_cmd()
which will set cmd->text_in_ptr to NULL without freeing
previously allocated buffer.
This patch fixes this issue by calling kfree(cmd->text_in_ptr)
in iscsit_setup_text_cmd() before assigning NULL to it.
For the first text request cmd->text_in_ptr is NULL as
cmd is memset to 0 in iscsit_allocate_cmd().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Call __kfree_skb() after processing skb to avoid
memory leak.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
On initial tcmu_configure_device call the info->name would
have already been allocated and set, so on the second call
make sure to free it first.
Reported-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
For most case the sg->length equals to PAGE_SIZE, so this bug won't
be triggered. Otherwise this will crash the kernel, for example when
all segments' sg->length equal to 1K.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random updates from Ted Ts'o:
"Add wait_for_random_bytes() and get_random_*_wait() functions so that
callers can more safely get random bytes if they can block until the
CRNG is initialized.
Also print a warning if get_random_*() is called before the CRNG is
initialized. By default, only one single-line warning will be printed
per boot. If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a
warning will be printed for each function which tries to get random
bytes before the CRNG is initialized. This can get spammy for certain
architecture types, so it is not enabled by default"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: reorder READ_ONCE() in get_random_uXX
random: suppress spammy warnings about unseeded randomness
random: warn when kernel uses unseeded randomness
net/route: use get_random_int for random counter
net/neighbor: use get_random_u32 for 32-bit hash random
rhashtable: use get_random_u32 for hash_rnd
ceph: ensure RNG is seeded before using
iscsi: ensure RNG is seeded before use
cifs: use get_random_u32 for 32-bit lock random
random: add get_random_{bytes,u32,u64,int,long,once}_wait family
random: add wait_for_random_bytes() API
|
