| Age | Commit message (Collapse) | Author |
|---|
|
In zynq_qspi_probe function, when enable the device clock is done,
the return of all the functions should goto the clk_dis_all label.
If num_cs is not right then this should return a negative error
code but currently it returns success.
Signed-off-by: zpershuai <zpershuai@gmail.com>
Link: https://lore.kernel.org/r/1622110857-21812-1-git-send-email-zpershuai@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the number of bytes for the op is greater than one, the read could
run off the end of the function stack and cause a crash.
This patch restores the behaviour of safely reading out of the original
opcode location.
Signed-off-by: Karen Dombroski <karen.dombroski@marsbioimaging.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210429053802.17650-3-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix kernel-doc warning.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210429053802.17650-2-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-zynq-qspi.c:143: warning: Function parameter or member 'dev' not described in 'zynq_qspi'
drivers/spi/spi-zynq-qspi.c:334: warning: Function parameter or member 'spi' not described in 'zynq_qspi_config_op'
drivers/spi/spi-zynq-qspi.c:334: warning: Excess function parameter 'qspi' description in 'zynq_qspi_config_op'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Cc: Sureshkumar Relli <nagasure@xilinx.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-10-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In xSPI mode, flashes expect 2-byte opcodes. The second byte is called
the "command extension". There can be 3 types of extensions in xSPI:
repeat, invert, and hex. When the extension type is "repeat", the same
opcode is sent twice. When it is "invert", the second byte is the
inverse of the opcode. When it is "hex" an additional opcode byte based
is sent with the command whose value can be anything.
So, make opcode a 16-bit value and add a 'nbytes', similar to how
multiple address widths are handled.
Some places use sizeof(op->cmd.opcode). Replace them with op->cmd.nbytes
The spi-mxic and spi-zynq-qspi drivers directly use op->cmd.opcode as a
buffer. Now that opcode is a 2-byte field, this can result in different
behaviour depending on if the machine is little endian or big endian.
Extract the opcode in a local 1-byte variable and use that as the buffer
instead. Both these drivers would reject multi-byte opcodes in their
supports_op() hook anyway, so we only need to worry about single-byte
opcodes for now.
The above two changes are put in this commit to keep the series
bisectable.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200623183030.26591-3-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Zynq QSPI controller features 2 CS. When the num-cs DT property
is set to 2, the hardware will be initialized to support having two
devices connected over each CS.
In this case, both CS lines are driven by the state of the U_PAGE
(upper page) bit. When unset, the lower page (CS0) is selected,
otherwise it is the upper page (CS1).
Change tested on a custom design featuring two SPI-NORs with different
CS on the Zynq-7000 QSPI bus.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-8-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Supporting more than one CS will need some tweaking of the linear
configuration register which is (rightfully) initialized in the
hardware initialization helper. The extra initialization needs the
knowledge of the actual number of CS, which is retrieved by reading
the value of the num-cs DT property.
As the initialization helper is called pretty early and might be
called much later in the probe without side effect, let's delay it a
bit so that the number of CS will be available when running this
helper. This way, adding support for multiple CS lines in a next patch
will be eased.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-7-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The code used to assert and de-assert a chip select line is very
complicated for no reason. Simplify the logic by either setting or
resetting the concerned bit, which actually only changes an electrical
state.
Update the comment to reflect that there is no possibility to actually
choose a CS as the default (CS0) will be driven in any case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-6-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Using masks makes sense when manipulating fields of several bits. When
only one bit is involved, it is usual to just use the BIT() macro but
in this case using the term mask is abusive. Fix the #define macros
and their comments.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-5-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Most of the bits/bitfields #define'd in this driver are composed with:
1/ the driver prefix
2/ the name of the register they apply to
Keep the naming consistent by applying this rule to the CONFIG register
internals. These definitions will be used in a following change set.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-4-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Unlike what the driver is currently advertizing, CS0 only can be used,
CS1 is not supported at all. Prevent people to use CS1.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-2-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In this driver (and also in a lot of other drivers in drivers/spi/),
the spi_controller structure is sometimes referred as 'ctlr' and
sometimes as 'ctrl'. Grepping there shows that 'ctlr' seems to be more
common so keep the naming consistent in this driver and s/ctrl/ctlr/.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108105920.19014-3-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This driver does not use any symbols from the legacy GPIO
header so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073624.23974-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-36-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
Use devm_spi_register_controller to fix missing spi_unregister_controller
when unload module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20190818095113.2397-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-42-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Alpha and some of the architectures are missing readsl/writesl functions.
so the zynq-qspi driver won't be able to build on these arches. hence use
ioread32_rep()/iowrite32_rep() instead of readsl()/writesl().
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for QSPI controller driver used by Xilinx Zynq SOC.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
