Age | Commit message (Collapse) | Author |
|
Commit 8b136baa5892 ("spi: pxa2xx: Detect number of enabled Intel LPSS SPI
chip select signals") added a block where lpss_ssp_setup() gets called
again for Intel LPSS SPI host controllers before checking number of chip
selects from the capabilities register.
There is no point in calling the function twice in probe so remove the
first call.
Reported-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'spi/topic/omap-uwire', 'spi/topic/owner', 'spi/topic/pxa' and 'spi/topic/pxa2xx' into spi-next
|
|
Extend the pxa2xx_spi_acpi_get_pdata() so that it can create platform data
also on platforms that do not support ACPI or if CONFIG_ACPI is not set.
Now it is expected that "pxa2xx-spi" platform device is either created with
explicit platform data or has an ACPI companion device.
However there is only little in pxa2xx_spi_acpi_get_pdata() that is really
dependent on ACPI companion and it can be reworked to cover also cases
where "pxa2xx-spi" device doesn't have ACPI companion and is created
without platform data.
Do this by renaming the pxa2xx_spi_acpi_get_pdata(), moving it outside of
CONFIG_ACPI test and changing a few runtime tests there to support non-ACPI
case. Only port/bus ID setting based on ACPI _UID is dependent on ACPI and
is moved to own function inside CONFIG_ACPI.
Purpose of this to support non-ACPI case for those PCI enumerated compound
devices that integrate both LPSS SPI host controller and integrated DMA
engine under the same PCI ID and which are registered in MFD layer instead
of in spi-pxa2xx-pci.c.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
LPSS SPI in Intel Broxton is otherwise the same than in Intel Sunrisepoint
but it supports up to four chip selects per port and has different FIFO
thresholds. Patch adds support for two Broxton SoC variants.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SPI capabilities register located in private registers space of newer
Intel LPSS SPI host controllers tell in register bits 12:9 which chip
select signals are enabled.
Use that information for detecting the number of chip selects. For
simplicity we assume chip selects are enabled one after another without
disabled chip selects between. For instance CS0 | CS1 | CS2 but not
CS0 | CS1 | CS3.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Intel LPSS SPI host controllers in upcoming Intel platforms can have up
to 4 chip selects per port. Extend chip select control in
lpss_ssp_cs_control() by adding a code that selects the active chip
select output prior to changing the state. Detection for number of
enabled chip select signals will be added by another patch.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rename a few defines that are specific to Intel LPSS SPI private
registers with LPSS prefix. It makes easier to distinguish them from
common defines.
Suggested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add more indentation to define lines for making them aligned with the
longest one. They would look messy after adding more long defines.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Upcoming Intel platforms use LPSS SPI_CS_CONTROL register bits 15:12 for
configuring the chip select polarities. Touch only chip select SW mode and
state bits when enabling the software chip select control in order to not
clear any other bits in the register.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Andy noticed numeric unique device ID is unsigned integer so convert it
using kstrtouint(). Actually integer in ACPI 2.0 and later is 64 bits
litte-endian unsigned integer but quite certainly having so big value here
would mean something extra than just the SPI bus number so it won't hurt to
assume only lower 32 bits carry the bus number for now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since we call pxa2xx_ssp_get_clk_div() from pump_transfers() we may derive
pointer to struct chip_data from struct drv_data like it's done in the rest
of the functions. This will make it less errorprone.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The speed can be changed from transfer to transfer, that's why the messages
do not depict the actual values during ->setup(). Move debug messages from
->setup() to pump_transfers(). Get rid of leftovers as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As per discussion [1] the best choice is to set closest speed which is not
going over the asked one.
Do the same approach for Intel Quark boards.
[1] http://www.spinics.net/lists/linux-spi/msg03389.html
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This was leftover from the legacy pxa2xx DMA implementation and not needed
anymore so remove it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Get pointer to the struct acpi_device by using ACPI_COMPANION() macro. This
is more efficient than using ACPI_HANDLE() and acpi_bus_get_device().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Carry input clock of the controller in max_speed_hz of struct spi_master
instead of in own driver data. They mean the same thing and more over now
the max_speed_hz is not even set here.
As an added bonus this allows SPI core to validate that transfer speed is
not beyond the maximum input clock. This is not a problem in spi-pxa2xx as
the driver doesn't use transfer speed parameter directly but via input
clock divider calculation which will top at divide by one. However it's
better to validate speed before passing it here.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'spi/fix/doc', 'spi/fix/mediatek', 'spi/fix/meson', 'spi/fix/mtk' and 'spi/fix/pxa2xx' into spi-linus
|
|
There hasn't been need to carry chip->cr0 after SPI core started to
validate speed_hz and bits_per_word transfer parameters. That effectively
caused that pump_transfers() always recalculated it and practically
chip->cr0 is used locally in setup() for debug prints only.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This is continuation to previous commit by separating unindentation from
variable removal done in previous commit. As said SPI core have validated
both the speed_hz and bits_per_word and the if statement here evaluates
always to true.
Remove the test and unindent the code block accordingly. While at it remove
also needless "cr0 = chip->cr0" as cr0 will be overwritten anyway and fix
block comment style.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is no need to carry spi->max_speed_hz and spi->bits_per_word from
setup() in "struct chip_data" since pump_transfers() will anyway take the
transfer parameters from "struct spi_transfer". This is since SPI core
validates both bits_per_word and speed_hz transfer parameters and defaults
to spi->bits_per_word and spi->max_speed_hz in case these per transfer
parameters are not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On Intel Baytrail, there is case when interrupt handler get called, no SPI
message is captured. The RX FIFO is indeed empty when RX timeout pending
interrupt (SSSR_TINT) happens.
Use the BIOS version where both HSUART and SPI are on the same IRQ. Both
drivers are using IRQF_SHARED when calling the request_irq function. When
running two separate and independent SPI and HSUART application that
generate data traffic on both components, user will see messages like
below on the console:
pxa2xx-spi pxa2xx-spi.0: bad message state in interrupt handler
This commit will fix this by first checking Receiver Time-out Interrupt,
if it is disabled, ignore the request and return without servicing.
Signed-off-by: Tan, Jui Nee <jui.nee.tan@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Remove null_dma_buf variable and extra allocation for it. It is not needed
since commit 6356437e65c2 ("spi: spi-pxa2xx: remove legacy PXA DMA bits").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
These became unused by the commit 6356437e65c2
("spi: spi-pxa2xx: remove legacy PXA DMA bits").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Major difference in LPSS SPI between Intel Sunrisepoint PCH and earlier
platforms is an integrated DMA (iDMA) engine. iDMA is an IP that is private
for each LPSS host controller (UART/SPI/I2C). Other differences are private
register space offset, a few private registers that are in different
location and FIFO thresholds.
Intel Sunrisepoint LPSS SPI and iDMA devices are probed and registered in
MFD layer as platform devices. Here these compound devices are detected by
matching against known PCI IDs. This allows us to share
pxa2xx_spi_acpi_get_pdata() for setting up the platform data instead of
duplicating it in MFD part.
This patch adds configuration for Intel Sunrisepoint LPSS SPI, above
detection and DMA filter function that picks the DMA channel only from an
associated iDMA block.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Constify the ACPI device ID array, it doesn't need to be writable at
runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
General register located in LPSS SPI private register space is not found in
upcoming Intel LPSS platforms. Access it conditionally depending is it
defined in configuration.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some of the Intel LPSS SPI properties will be different in upcoming
platforms compared to existing Lynxpoint and BayTrail/Braswell. LPSS SPI
private registers will be at different offset and there will be changes in
individual registers and default FIFO thresholds too.
Add configuration for these differences and use them in runtime based on
LPSS SSP type. With this change private registers offset autodetection
becomes needless.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Intel LPSS SPI properties differ between between platforms. Now private
registers offset 0x400 or 0x800 is autodetected but there is need to
support also other offset and handle a few other differences.
Prepare for that by splitting the LPSS_SSP type into compatible hardware
types and set it now based on PCI or ACPI ID. That type will be used to set
properties that differ between current and upcoming platforms.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We refactored this code but accidentally left out a break statement so
QUARK_X1000_SSP isn't handled correctly.
Fixes: 025ffe88ee60 ('spi: pxa2xx: shift clk_div in one place')
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Quark SoC data sheet describes the baud rate setting using fractional
divider. The subset of possible values represented by a table suggests that the
divisor has one block that could divide by 5. This explains the number of the
beast in some cases in the table. Thus, in this particular case the divisor can
be evaluated as
5^i * 2^j * 2 * k,
where
i = [0, 1]
j = [0, 23]
k = [1, 256]
There are few cases as mentioned in the data sheet, i.e. better form of the
clock signal will be in case if DDS_CLK_RATE either 2^n or 2/5. It's also
possible to use any value that is less or equal to 0x33333 (1/5/16 = 1/80).
All three cases are compared to each other and the one that suits better is
chosen by the approximation algorithm. Anyone can play with the script [1] that
represents the algorithm.
[1] https://gist.github.com/06b084488b3629898121
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch refactors ssp_get_clk_div() and pxa2xx_ssp_get_clk_div() to align
clk_div calculations, i.e. ssp_get_clk_div() and quark_x1000_set_clk_regvals()
will return plain clk_div and it will be shifted to proper position in
pxa2xx_ssp_get_clk_div().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
These asm/io.h, asm/irq.h and asm/delay.h are needless since they are
already included by linux/io.h via drivers/spi/spi-pxa2xx.h,
linux/interrupt.h and linux/delay.h.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'spi/topic/qup', 'spi/topic/rockchip' and 'spi/topic/samsung' into spi-next
|
|
'spi/topic/fsl', 'spi/topic/fsl-dspi' and 'spi/topic/gpio' into spi-next
|
|
Commit 7566bcc76b15 ("spi: pxa2xx: Move is_lpss_ssp() tests to caller") did
not check LPSS before calling lpss_ssp_setup() in pxa2xx_spi_resume().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Once the current message is finished, the driver notifies SPI core about
this by calling spi_finalize_current_message(). This function queues next
message to be transferred. If there are more messages in the queue, it is
possible that the driver is asked to transfer the next message at this
point.
When spi_finalize_current_message() returns the driver clears the
drv_data->cur_chip pointer to NULL. The problem is that if the driver
already started the next message clearing drv_data->cur_chip will cause
NULL pointer dereference which crashes the kernel like:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
IP: [<ffffffffa0022bc8>] cs_deassert+0x18/0x70 [spi_pxa2xx_platform]
PGD 78bb8067 PUD 37712067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in:
CPU: 1 PID: 11 Comm: ksoftirqd/1 Tainted: G O 3.18.0-rc4-mjo #5
Hardware name: Intel Corp. VALLEYVIEW B3 PLATFORM/NOTEBOOK, BIOS MNW2CRB1.X64.0071.R30.1408131301 08/13/2014
task: ffff880077f9f290 ti: ffff88007a820000 task.ti: ffff88007a820000
RIP: 0010:[<ffffffffa0022bc8>] [<ffffffffa0022bc8>] cs_deassert+0x18/0x70 [spi_pxa2xx_platform]
RSP: 0018:ffff88007a823d08 EFLAGS: 00010202
RAX: 0000000000000008 RBX: ffff8800379a4430 RCX: 0000000000000026
RDX: 0000000000000000 RSI: 0000000000000246 RDI: ffff8800379a4430
RBP: ffff88007a823d18 R08: 00000000ffffffff R09: 000000007a9bc65a
R10: 000000000000028f R11: 0000000000000005 R12: ffff880070123e98
R13: ffff880070123de8 R14: 0000000000000100 R15: ffffc90004888000
FS: 0000000000000000(0000) GS:ffff880079a80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000048 CR3: 000000007029b000 CR4: 00000000001007e0
Stack:
ffff88007a823d58 ffff8800379a4430 ffff88007a823d48 ffffffffa0022c89
0000000000000000 ffff8800379a4430 0000000000000000 0000000000000006
ffff88007a823da8 ffffffffa0023be0 ffff88007a823dd8 ffffffff81076204
Call Trace:
[<ffffffffa0022c89>] giveback+0x69/0xa0 [spi_pxa2xx_platform]
[<ffffffffa0023be0>] pump_transfers+0x710/0x740 [spi_pxa2xx_platform]
[<ffffffff81076204>] ? pick_next_task_fair+0x744/0x830
[<ffffffff81049679>] tasklet_action+0xa9/0xe0
[<ffffffff81049a0e>] __do_softirq+0xee/0x280
[<ffffffff81049bc0>] run_ksoftirqd+0x20/0x40
[<ffffffff810646df>] smpboot_thread_fn+0xff/0x1b0
[<ffffffff810645e0>] ? SyS_setgroups+0x150/0x150
[<ffffffff81060f9d>] kthread+0xcd/0xf0
[<ffffffff81060ed0>] ? kthread_create_on_node+0x180/0x180
[<ffffffff8187a82c>] ret_from_fork+0x7c/0xb0
Fix this by clearing drv_data->cur_chip before we call spi_finalize_current_message().
Reported-by: Martin Oldfield <m@mjoldfield.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Currently SSP registers are accessed by having an own read and write macros
for each register. For instance read_SSSR(iobase) and write_SSSR(iobase).
In my opinion this hurts readability and requires new macros to be defined
for each new added register. Let's define and use instead common
pxa2xx_spi_read() and pxa2xx_spi_write() accessors.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move is_lpss_ssp() tests from functions to caller. Although this aims to
improve readability it also saves a few code bytes on x86.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
|
After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/spi/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
|
|
There are two SPI controllers exported by PCI subsystem for Intel Quark X1000.
The SPI memory mapped I/O registers supported by Quark are different from
the current implementation, and Quark only supports the registers of 'SSCR0',
'SSCR1', 'SSSR', 'SSDR', and 'DDS_RATE'. This patch is to enable the SPI for
Intel Quark X1000.
This piece of work is derived from Dan O'Donovan's initial work for Intel Quark
X1000 SPI enabling.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are several registers for SPI, and the registers of 'SSCR0' and 'SSCR1'
are accessed frequently. This path is to introduce helper functions to
simplify the accessing of 'SSCR0' and 'SSCR1'.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If PM_RUNTIME is enabled, it is easy to trigger the following backtrace
on pxa2xx hosts:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /home/lumag/linux/arch/arm/mach-pxa/clock.c:35 clk_disable+0xa0/0xa8()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00007-g1b3d2ee-dirty #104
[<c000de68>] (unwind_backtrace) from [<c000c078>] (show_stack+0x10/0x14)
[<c000c078>] (show_stack) from [<c001d75c>] (warn_slowpath_common+0x6c/0x8c)
[<c001d75c>] (warn_slowpath_common) from [<c001d818>] (warn_slowpath_null+0x1c/0x24)
[<c001d818>] (warn_slowpath_null) from [<c0015e80>] (clk_disable+0xa0/0xa8)
[<c0015e80>] (clk_disable) from [<c02507f8>] (pxa2xx_spi_suspend+0x2c/0x34)
[<c02507f8>] (pxa2xx_spi_suspend) from [<c0200360>] (platform_pm_suspend+0x2c/0x54)
[<c0200360>] (platform_pm_suspend) from [<c0207fec>] (dpm_run_callback.isra.14+0x2c/0x74)
[<c0207fec>] (dpm_run_callback.isra.14) from [<c0209254>] (__device_suspend+0x120/0x2f8)
[<c0209254>] (__device_suspend) from [<c0209a94>] (dpm_suspend+0x50/0x208)
[<c0209a94>] (dpm_suspend) from [<c00455ac>] (suspend_devices_and_enter+0x8c/0x3a0)
[<c00455ac>] (suspend_devices_and_enter) from [<c0045ad4>] (pm_suspend+0x214/0x2a8)
[<c0045ad4>] (pm_suspend) from [<c04b5c34>] (test_suspend+0x14c/0x1dc)
[<c04b5c34>] (test_suspend) from [<c000880c>] (do_one_initcall+0x8c/0x1fc)
[<c000880c>] (do_one_initcall) from [<c04aecfc>] (kernel_init_freeable+0xf4/0x1b4)
[<c04aecfc>] (kernel_init_freeable) from [<c0378078>] (kernel_init+0x8/0xec)
[<c0378078>] (kernel_init) from [<c0009590>] (ret_from_fork+0x14/0x24)
---[ end trace 46524156d8faa4f6 ]---
This happens because suspend function tries to disable a clock that is
already disabled by runtime_suspend callback. Add if
(!pm_runtime_suspended()) checks to suspend/resume path.
Fixes: 7d94a505858 (spi/pxa2xx: add support for runtime PM)
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
|
|
That field has been deprecated in favour of getting the necessary
information from ACPI/DT.
However, we still need to deal systems that are PCI only (no ACPI to back
up). In order to support such systems, we allow the DMA filter function and
its corresponding parameter via pxa2xx_spi_master platform data. Then when
the pxa2xx_spi_dma_setup() doesn't find the channel via ACPI, it falls back
to use the given filter function.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|