| Age | Commit message (Collapse) | Author |
|---|
|
The orion spi driver currently only supports the normal (i.e. MSB) mode.
This patch adds LSB first mode.
Also correct the comment about supported SPI modes that was left over by
b15d5d7004e2 ("spi/orion: Add SPI_CHPA and SPI_CPOL support to kirkwood
driver.").
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The calculation of SPR and SPPR doesn't round correctly at several
places which might result in baud rates that are too big. For example
with tclk_hz = 250000001 and target rate 25000000 it determined a
divider of 10 which is wrong.
Instead of fixing all the corner cases replace the calculation by an
algorithm without a loop which should even be quicker to execute apart
from being correct.
Fixes: df59fa7f4bca ("spi: orion: support armada extended baud rates")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds support for the direct access mode to the Orion SPI
driver which is used on the Marvell Armada based SoCs. In this direct
mode, all data written to (or read from) a specifically mapped MBus
window (linked to one SPI chip-select on one of the SPI controllers)
will be transferred directly to the SPI bus. Without the need to control
the SPI registers in between. This can improve the SPI transfer rate in
such cases.
Both, direct-read and -write mode are supported. But only the write
mode has been tested. This mode especially benefits from the SPI direct
mode, as the data bytes are written head-to-head to the SPI bus,
without any additional addresses.
One use-case for this direct write mode is, programming a FPGA bitstream
image into the FPGA connected to the SPI bus at maximum speed.
This mode is described in chapter "22.5.2 Direct Write to SPI" in the
Marvell Armada XP Functional Spec Datasheet.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Description:
On Armada 38x, the device SPI interface supports frequencies of up to
50 MHz. However, due to this erratum, when the device core clock is
250 MHz and the SPI interfaces is configured for 50MHz SPI clock and
CPOL=CPHA=1, there might occur data corruption on reads from the SPI
device.
Workaround:
Work in one of the following configurations:
1. Set CPOL=CPHA=0 in "SPI Interface Configuration Register".
2. Set TMISO_SAMPLE value to 0x2 in "SPI Timing Parameters 1 Register"
before setting the interface.
[gregory.clement@free-electrons.com}: port to v4.2-rc, use
is_errata_50mhz_ac instead of using a new ARMADA_380_SPI spi type.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
The commit df59fa7f4bca "spi: orion: support armada extended baud
rates" made the assumptions that all the Armada SoCs supported the
same maximum frequency. However, according the hardware datasheet, the
maximum frequency supported by the Armada 370 SoC is tclk/4, for the
Armada XP, Armada 38x and Armada 39x SoCs the limitation is 50MHz and
for the Armada 375 it is tclk/15.
This patch introduces new compatible strings to handle all these
case. In order to be future proof a compatible was created for each
SoC even if currently some SoCs seem using the same IP.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The commit df59fa7f4bca "spi: orion: support armada extended baud
rates" was too optimistic for the maximum baud rate that the Armada
SoCs can support. According to the hardware datasheet the maximum
frequency supported by the Armada 370 SoC is tclk/4. But for the
Armada XP, Armada 38x and Armada 39x SoCs the limitation is 50MHz and
for the Armada 375 it is tclk/15.
Currently the armada-370-spi compatible is only used by the Armada 370
and the Armada XP device tree. On Armada 370, tclk cannot be higher
than 200MHz. In order to be able to handle both SoCs, we can take the
minimum of 50MHz and tclk/4.
A proper solution is adding a compatible string for each SoC, but it
can't be done as a fix for compatibility reason (we can't modify
device tree that have been already released) and it will be part of a
separate patch.
Fixes: df59fa7f4bca (spi: orion: support armada extended baud rates)
Reported-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
|
|
This commit adds support for multiple hardware chip selects to spi-orion.
Different SoCs support different number of chip selects (up to
8 on some platforms). The driver allows up to this number, and it is up
to the implementer to only use the chip selects that are available.
Signed-off-by: Ken Wilson <ken.wilson@opengear.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This commit changes spi-orion to provide setup, set_cs, and transfer_one
functions instead of transfer_one_message. This allows chip select support
for both native and GPIO chip selects to be added.
Signed-off-by: Ken Wilson <ken.wilson@opengear.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
|
|
After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/spi/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into driver-core-next
Remove all .owner fields from platform drivers
|
|
It's possible that the call to of_match_device() (introduced in commit
df59fa7f ["spi: orion: support armada extended baud rates"]) may return
a NULL if there is no match in the device tree (or perhaps no device tree
at all). Check the return pointer and set the local device data to the
lowest common denominator orion device data if it is NULL.
Reported-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
'spi/topic/mxs', 'spi/topic/omap-100k' and 'spi/topic/orion' into spi-next
|
|
The Armada SoC family implementation of this SPI hardware module has
extended the configuration register to allow for a wider range of SPI
clock rates. Specifically the Serial Baud Rate Pre-selection bits in the
SPI Interface Configuration Register now also use bits 6 and 7 as well.
Modify the baud rate calculation to handle these differences for the
Armada case. Potentially a baud rate can be setup using a number of
different pre-scalar and scalar combinations. This code tries all
possible pre-scalar divisors (8 in total) to try and find the most
accurate set.
This change introduces (and documents) a new device tree compatible
device name "armada-370-spi" to support this.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the following checkpatch warnings.
WARNING: else is not generally useful after a break or return
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'spi/topic/qup', 'spi/topic/rockchip' and 'spi/topic/rspi' into spi-next
|
|
In commit f814f9ac5a81 ("spi/orion: add device tree binding"), Device
Tree support was added to the spi-orion driver. However, this commit
reads the "cell-index" property, without taking into account the fact
that DT properties are big-endian encoded.
Since most of the platforms using spi-orion with DT have apparently
not used anything but cell-index = <0>, the problem was not
visible. But as soon as one starts using cell-index = <1>, the problem
becomes clearly visible, as the master->bus_num gets a wrong value
(actually it gets the value 0, which conflicts with the first bus that
has cell-index = <0>).
This commit fixes that by using of_property_read_u32() to read the
property value, which does the appropriate endianness conversion when
needed.
Fixes: f814f9ac5a81 ("spi/orion: add device tree binding")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org> # v3.6+
|
|
Fix to return a negative error code from the error handling case of
orion_spi_reset() instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add trivial runtime PM support. This will only be of benefit on SoCs
where the clock to the SPI interface can be shut down.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
clk_prepare()/clk_enable() can fail, and it's return value should
be checked. Add the proper checking, and while we're here, convert
to clk_prepare_enable().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
'spi/topic/omap2', 'spi/topic/orion', 'spi/topic/pl022', 'spi/topic/qup', 'spi/topic/rspi' and 'spi/topic/s3c24xx' into spi-next
|
|
spi core will handle validating transfer length since commit 4d94bd21b333
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Since commit a2fd4f9fa3b9 'spi: Support transfer speed checking in the core',
the SPI core validates the desired speed of a given transfer against the
minimum and maximum speeds supported by the controller.
So we can remove the same code in this driver and let spi core handle checking
the desired speed of a given transfer.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Remove unused devdata pointer 'orion_spi' in function orion_spi_write_read().
Detected by Coverity: CID 1077860.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Use devm_clk_get() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
Fix the following checkpatch warnings.
WARNING: quoted string split across lines
WARNING: sizeof *spi should be sizeof(*spi)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Use devm_spi_register_master() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
|
|
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch reduces and simplifies initalization code by
using module_platform_driver().
With this change it's necessary to remove the __init annotation
to avoid section mismatch warnings.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Some of the spi driver module remove hooks were annotated with __exit
and referenced with __exit_p(). Presumably these were supposed to be
__devinit, __devexit and __devexit_p() since __init/__exit for a
probe/remove hook has never been correct. They also got missed during
the big __devinit/__devexit purge since they didn't match the pattern.
Remove then now to be rid of it.
v2: purge __init also
Reported-by: Arnd Bergmann <arnd@arndb.de>
[Arnd set a patch cleaning up one, and then I found more]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Support these transfer modes from the SPI layer by setting
the appropriate register bits before doing the transfer.
This was tested on the Marvell kirkwood SOC that uses this driver.
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Replace the deprecated master->transfer with transfer_one_message()
and allow the SPI subsystem handle all the queuing of messages.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This was formerly used to store the tclk value. This is now discovered
using the clk API, rather than pass it as platform data.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Remove now redundant tclk from SPI platform data. This makes the platform
data empty, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
|
|
We are clipping down the presence of module.h, since it was
everywhere. If you really need it, you better call it out,
as per this changeset.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.
This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.
v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
be the predominant pattern for subsystem prefixes.
- Clean up filenames in Kconfig and header comment blocks
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
