| Age | Commit message (Collapse) | Author |
|---|
|
Commit adef658 "spi/omap_mcspi: catch xfers of non-multiple SPI word size"
broke the transmission of last word in cases where access is multiple of
word size and word size is 16 or 32 bits.
Fix this by replacing the test "c > (word_len>>3)" in do-while loops with
"c >= 'pointer increment size'". This ensures that the last word is
transmitted in above case and still allow to break the loop and prevent
variable c underflow in cases where word size != 'pointer increment size'.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Sourav Poddar<sourav.poddar@ti.com>
Acked-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/dw_spi: move dw_spi.h into drivers/spi
spi/dw_spi: Fix missing header
gpio/langwell: Clear edge bit before handling
gpio/langwell: Simplify demux loop
gpio/langwell: Convert irq name space
gpio/langwell: Fix broken irq_eoi change.
gpio; Make Intel chipset gpio drivers depend on x86
gpio/cs5535-gpio: Fix section mismatch
spi/rtc-{ds1390,ds3234,m41t94}: Use spi_get_drvdata() for SPI devices
spi/davinci: Support DMA transfers larger than 65535 words
spi/davinci: Use correct length parameter to dma_map_single calls
gpio: Use __devexit at necessary places
gpio: add MODULE_DEVICE_TABLE to pch_gpio and ml_ioh_gpio
gpio/mcp23s08: support mcp23s17 variant
of_mmc_spi: add card detect irq support
spi/omap_mcspi: catch xfers of non-multiple SPI word size
spi/omap_mcspi: Off-by-one error in finding the right divisor
gpio/pca953x: Fix wrong pointer type
spi/pl022: rid dangling labels
spi: add support for SuperH SPI
...
|
|
If an SPI access was not a multiple of the SPI word size,
the while() loop would spin and the rx/tx ptrs would be incremented
indefinitely.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Off-by-one error, gave erroneous divisor value 16 if speed_hz is over zero but
less than OMAP2_MCSPI_MAX_FREQ / (1 << 15), that is, [1..1463].
Also few overly complex bit shifts in divisor fixed.
Also one dev_dgb line fixed, which indicated max speed exceeding transfer speed.
Introducing a new function omap2_mcspi_calc_divisor() for getting the right
divisor in omap2_mcspi_setup_transfer().
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Hannu Heikkinen <ext-hannu.m.heikkinen@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
McSPI runtime conversion.
Changes involves:
1) remove clock framework apis to use runtime framework apis.
2) context restore from runtime resume which is a callback for get_sync.
3) Remove SYSCONFIG(sysc) register handling
(a) Remove context save and restore of sysc reg and remove soft reset
done from sysc reg as this will be done with hwmod framework.
(b) Also cleanup sysc reg bit macros.
4) Rename the omap2_mcspi_reset function to omap2_mcspi_master_setup
function as with hwmod changes soft reset will be done in
hwmod framework itself and use the return value from clock
enable function to return for failure scenarios.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Partha Basak <p-basak2@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Cleans up all base address definitions for omap_mcspi
and adapts the device registration and driver to hwmod framework.
Changes involves:
1) Removing all base address macro defines.
2) Using omap-device layer to register device and utilizing data from
hwmod data file for base address, dma channel number, Irq_number,
device attribute(number of chipselect).
3) Appending base address with pdata reg_offset for omap4 boards.
For omap4 all regs used in driver deviate with reg_offset_macros
defined with an value of 0x100. So pass this offset through pdata
and append the same to base address retrieved from hwmod data file
and we are not mapping *_HL_* regs which are not used in driver.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Partha Basak <p-basak2@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest
are nowadays just subcategories of these.
Search and replace the following:
ARCH_OMAP2420 SOC_OMAP2420
ARCH_OMAP2430 SOC_OMAP2430
ARCH_OMAP3430 SOC_OMAP3430
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
|
|
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (77 commits)
spi/omap: Fix DMA API usage in OMAP MCSPI driver
spi/imx: correct the test on platform_get_irq() return value
spi/topcliff: Typo fix threhold to threshold
spi/dw_spi Typo change diable to disable.
spi/fsl_espi: change the read behaviour of the SPIRF
spi/mpc52xx-psc-spi: move probe/remove to proper sections
spi/dw_spi: add DMA support
spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
spi/dw_spi: Fix too short timeout in spi polling loop
spi/pl022: convert running variable
spi/pl022: convert busy flag to a bool
spi/pl022: pass the returned sglen to the DMA engine
spi/pl022: map the buffers on the DMA engine
spi/topcliff_pch: Fix data transfer issue
spi/imx: remove autodetection
spi/pxa2xx: pass of_node to spi device and set a parent device
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add CE4100 support
...
|
|
Running the latest kernel on the 4430SDP board with DMA API debugging
enabled results in this:
WARNING: at lib/dma-debug.c:803 check_unmap+0x19c/0x6f0()
NULL NULL: DMA-API: device driver tries to free DMA memory it has not allocated
[device address=0x000000008129901a] [size=260 bytes]
Modules linked in:
Backtrace:
[<c003cbe0>] (dump_backtrace+0x0/0x10c) from [<c0278da8>] (dump_stack+0x18/0x1c)
r7:c1839dc0 r6:c0198578 r5:c0304b17 r4:00000323
[<c0278d90>] (dump_stack+0x0/0x1c) from [<c005b158>] (warn_slowpath_common+0x58/0x70)
[<c005b100>] (warn_slowpath_common+0x0/0x70) from [<c005b214>] (warn_slowpath_fmt+0x38/0x40)
r8:c1839e40 r7:00000000 r6:00000104 r5:00000000 r4:8129901a
[<c005b1dc>] (warn_slowpath_fmt+0x0/0x40) from [<c0198578>] (check_unmap+0x19c/0x6f0)
r3:c03110de r2:c0304e6b
[<c01983dc>] (check_unmap+0x0/0x6f0) from [<c0198cd8>] (debug_dma_unmap_page+0x74/0x80)
[<c0198c64>] (debug_dma_unmap_page+0x0/0x80) from [<c01d5ad8>] (omap2_mcspi_work+0x514/0xbf0)
[<c01d55c4>] (omap2_mcspi_work+0x0/0xbf0) from [<c006dfb0>] (process_one_work+0x294/0x400)
[<c006dd1c>] (process_one_work+0x0/0x400) from [<c006e50c>] (worker_thread+0x220/0x3f8)
[<c006e2ec>] (worker_thread+0x0/0x3f8) from [<c00738d0>] (kthread+0x88/0x90)
[<c0073848>] (kthread+0x0/0x90) from [<c005e924>] (do_exit+0x0/0x5fc)
r7:00000013 r6:c005e924 r5:c0073848 r4:c1829ee0
---[ end trace 1b75b31a2719ed20 ]---
I've no idea why this driver uses NULL for dma_unmap_single instead of
the &spi->dev that is laying around just waiting to be used in that
function - but it's an easy fix.
Also replace this comment with a FIXME comment:
/* Do DMA mapping "early" for better error reporting and
* dcache use. Note that if dma_unmap_single() ever starts
* to do real work on ARM, we'd need to clean up mappings
* for previous transfers on *ALL* exits of this loop...
*/
as the comment is not true - we do work in dma_unmap() functions,
particularly on ARMv6 and above. I've corrected the existing unmap
functions but if any others are required they must be added ASAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
When SPI wake up from OFF mode, CS is in the wrong state: force it to the
inactive state.
During the system life, I monitored the CS behavior using a oscilloscope.
I also activated debug in omap2_mcspi, so I saw when driver disable the clocks
and restore context when device is not used.Each time the CS was in the correct
state. It was only when system was put suspend to ram with off-mode activated
that on resume the CS was in wrong state( ie activated).
Changelog:
* Change from v1 to v2:
- Rebase on linus/master (after 2.6.37-rc1)
- Do some clean-up and fix indentation on both patches
- Add more explanations for patch 2
* Change from v2 to v3:
- Use directly resume function of spi_master instead of using function
- from spi_device as Grant Likely pointed it out.
- Force this transition explicitly for each CS used by a device.
* Change from v3 to v4:
- Patch clean-up according to Kevin Hilman and checkpatch.
- Now force CS to be in inactive state only if it was inactive when it was
suspended.
* Change from v4 to v5:
- Rebase on linus/master (after 2.6.37-rc3)
- Collapse some lines as pointed by Grant Likely
- Fix a spelling
* Change from v5 to v6:
- Rebase on linus/master (after 2.6.37-rc7)
- Use CONFIG_SUSPEND instead of CONFIG_PM
- Didn't use legacy PM methods anymore. Instead, add a struct dev_pm_ops and
add the resume method there.
- Fix multi-line comment style
* Change from v6 to v7:
- Rebase on linus/master (after 2.6.37-rc8)
- Drop an extra line
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
In case of TX only with DMA, the driver assumes that the data
has been transferred once DMA callback in invoked. However,
SPI's shift register may still contain data. Thus, the driver
is supposed to verify that the register is empty and the end of
the SPI transfer has been reached.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
In the TX_ONLY transfer, the SPI controller also receives data
simultaneously and saves them in the rx register. After the TX_ONLY
transfer, the rx register will hold the random data received during
the last tx transaction.
If the direct following transfer is RX_ONLY, this random data has the
possibility to affect this transfer like this:
When the SPI controller is changed from TX_ONLY to RX_ONLY,
the random data makes the rx register full immediately and
triggers a dummy write automatically(in SPI RX_ONLY transfers,
we need a dummy write to trigger the first transaction).
So the first data received in the RX_ONLY transfer will be that
random data instead of something meaningful.
We can avoid this by inserting a Disable/Re-enable toggle of the
channel after the TX_ONLY transfer, since it purges the rx register.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
dev_vdbg() is only compiled when VERBOSE is defined, so
there's no need to wrap dev_dbg() on #ifdef VERBOSE .. #endif
as we can use dev_vdbg() directly.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Check spi->chip_select for range before use.
Signed-off-by: Scott Ellis <scott@jumpnowtek.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Turbo mode allows to read data to shift register when rx-buffer
is full thus improving the perfomance. This feature is available
for RX-only mode.
In PIO turbo mode when the penultimate word is available
in RX-buffer the controller should be disabled before reading data
to prevent the next transaction triggering. The controller itself
handles the last word to be correctly loaded to shift-register and
then transferred to RX-buffer.
The turbo mode is enabled by setting turbo_mode parameter to 1.
This parameter is a part of omap2_mcspi_device_config structure
which is passed through the spi_device controller_data pointer.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The value 160 has been obtained as optimal in testing it for
wl1271 which use spi for communication.
In some sense this change might also influence on other spi devices
connected to omap2_mcspi controller.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Replaces %04x by %08x for 32-bits data output.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
mcspi_write_chconf0 is used to control rx/tx triggering.
Post-write flushing is needed to get the immediate effect.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
omap2_mcspi_transfer() gets called in omap2_mcspi_work() when the
transaction speed_hz or bits_per_word fields are non-zero.
omap2_mcspi_transfer() does not look at the speed_hz field so
the override speed value is ignored.
The code should probably change to one of these options.
1. Skip the call to omap2_mcsp_transfer() if the only reason was a
non-zero speed_hz and it's not going to be used.
2. Use the new speed_hz value provided
The patch below uses the speed_hz value.
Signed-off-by: Scott Ellis <scott@jumpnowtek.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Check spi->controller_state before dereferencing.
Shows up NULL here when using spi_alloc_device()/spi_add_device()
and spi_add_device() fails before spi_setup(). Calling spi_dev_put()
on the leftover spi_device results in the error.
Signed-off-by: Scott Ellis <scott@jumpnowtek.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Replace ARCH_OMAP34XX with ARCH_OMAP3
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
tAdd adds McSPI support for OMAP4430 SDP platform. All the base addresses
are changed between OMAP1/2/3 and OMAP4. The fields of the resource
structures are filled at runtime to have McSPI support on OMAP4.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Previous restore was lazy and only restored CHxCONF when it was needed by
a specific chip select. This could cause occasional errors on an SPI bus
where multiple chip selects are in use.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add context save/restore feature to McSPI driver.
Signed-off-by: Hemanth V <hemanthv@ti.com>
Reviewed-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert bit shifted values into BIT format
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When data is read through DMA, the last element must be read separately
through the RX register. It cannot be transferred by the DMA. For
further details see e.g. OMAP35x TRM (table 19-16).
Without the fix the driver causes extra clocks to be clocked to the bus
after DMA RX operations. This can cause interesting behaviour with some
devices.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
[aaro.koskinen@nokia.com: Simplified the patch while keeping the idea.]
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently mcspi wake-ups are not enabled. This might cause cases where
OMAP is not waking up on mcspi events.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move some common spi_setup() error checks into the SPI framework from the
spi_master controller drivers:
- Add a new "mode_bits" field to spi_master
- Use that in spi_setup to validate the spi->mode value being
requested. Setting this new field is now mandatory for any
controller supporting more than vanilla SPI_MODE_0.
- Update all spi_master drivers to:
* Initialize that field
* Remove current spi_setup() checks using that value.
This is a net minor code shrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Start moving some spi_setup() functionality into the SPI core from the
various spi_master controller drivers:
- Make that function stop being an inline;
- Move two common idioms from drivers into that new function:
* Default bits_per_word to 8 if that field isn't set
* Issue a standardized dev_dbg() message
This is a net minor source code shrink, and supports enhancments found in
some follow-up patches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Conflicts:
sound/soc/pxa/pxa2xx-i2s.c
|
|
Cc: dbrownell@users.sourceforge.net
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
|
|
... rather than the clock names themselves.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When omap_udc is also incorporated, this macro will no longer be used.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable SPI
platform drivers, to allow module auto loading.
[dbrownell@users.sourceforge.net: more drivers: registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds driver OMAP SPI specific changes to support OMAP 3430
Signed-off-by: Girish S G <girishsg@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Before transmission of the last word in PIO RX_ONLY mode rx+tx mode
is enabled:
/* prevent last RX_ONLY read from triggering
* more word i/o: switch to rx+tx
*/
if (c == 0 && tx == NULL)
mcspi_write_cs_reg(spi,
OMAP2_MCSPI_CHCONF0, l);
But because c is decremented after the test, c will never be zero and
rx+tx will not be enabled. This breaks RX_ONLY mode PIO transfers.
Fix it by decrementing c in the beginning of the various I/O loops.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove unused variable & write space
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add OMAP24XX McSPI (Multichannel SPI) controller driver. This driver is
tested very well under OMAP GIT tree with N800 - Nokia Internet Tablet, and
some other OMAP2 boards.
Recent updates included bugfixes, cleanups, speedups, and better
conformance to the current SPI programming interface. This doesn't yet
understand the third controller instance on the OMAP 2430.
[david-b@pacbell.net: more minor cleanups to the omap2_mcspi driver]
Signed-off-by: Juha Yrjölä <juha.yrjola@solidboot.com>
Signed-off-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
