| Age | Commit message (Collapse) | Author |
|---|
|
The SCU firmware API for getting UID should have response,
otherwise, the message stored in function stack could be
released and then the response data received from SCU will be
stored into that released stack and cause kernel NULL pointer
dump.
Fixes: 73feb4d0f8f1 ("soc: imx-scu: Add SoC UID(unique identifier) support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
|
|
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm ARM Based Driver Updates for v5.4
* Add AOSS QMP support
* Various fixups for Qualcomm SCM
* Add socinfo driver
* Add SoC serial number attribute and associated APIs
* Add SM8150 and SC7180 support in Qualcomm SCM
* Fixup max processor count in SMEM
* tag 'qcom-drivers-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: aoss: Add AOSS QMP support
dt-bindings: soc: qcom: aoss: Add SM8150 and SC7180 support
dt-bindings: firmware: scm: Add SM8150 and SC7180 support
dt-bindings: firmware: scm: re-order compatible list
soc: qcom: smem: Update max processor count
soc: qcom: socinfo: Annotate switch cases with fall through
soc: qcom: Extend AOSS QMP driver to support resources that are used to wake up the SoC.
soc: qcom: socinfo: Expose image information
soc: qcom: socinfo: Expose custom attributes
soc: qcom: Add socinfo driver
base: soc: Export soc_device_register/unregister APIs
base: soc: Add serial_number attribute to soc
firmware: qcom_scm: Cleanup code in qcom_scm_assign_mem()
firmware: qcom_scm: Fix some typos in docs and printks
firmware: qcom_scm: Use proper types for dma mappings
|
|
When booting with ACPI, the Geni Serial Engine is not set as the I2C/SPI
parent and thus, the wrapper (parent device) is unassigned. This causes
the kernel to crash with a null dereference error.
Link: https://lore.kernel.org/r/20190905082555.15020-1-lee.jones@linaro.org
Fixes: 8bc529b25354 ("soc: qcom: geni: Add support for ACPI")
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/drivers
Samsung soc drivers changes for v5.4, part 2
Fixes and cleanups for recently introduced Exynos chipid driver.
* tag 'samsung-drivers-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: chipid: Select missing dependency for EXYNOS_CHIPID
soc: samsung: chipid: Remove the regmap lookup error log
soc: samsung: chipid: Fix memory leak in error path
Link: https://lore.kernel.org/r/20190904175002.10487-3-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
TISCI protocol supports for enabling the device either with exclusive
permissions for the requesting host or with sharing across the hosts.
There are certain devices which are exclusive to Linux context and
there are certain devices that are shared across different host contexts.
So add support for getting this information from DT by increasing
the power-domain cells to 2.
For keeping the DT backward compatibility intact, defaulting the
device permissions to set the exclusive flag set. In this case the
power-domain-cells is 1.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers update for 5.4:
- A series from Anson Huang to add UID support for i.MX8 SoC and SCU
drivers.
- A series from Daniel Baluta to add DSP IPC driver for communication
between host AP (Linux) and the firmware running on DSP embedded in
i.MX8 SoCs.
- A small fix for GPCv2 error code printing.
- Switch from module_platform_driver_probe() to module_platform_driver()
for imx-weim driver, as we need the driver to probe again when device
is present later.
- Add optional burst clock mode support for imx-weim driver.
* tag 'imx-drivers-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: gpcv2: Print the correct error code
bus: imx-weim: use module_platform_driver()
firmware: imx: Add DSP IPC protocol interface
soc: imx-scu: Add SoC UID(unique identifier) support
bus: imx-weim: optionally enable burst clock mode
firmware: imx: scu-pd: Add IRQSTR_DSP PD range
firmware: imx: scu-pd: Add mu13 b side PD range
firmware: imx: scu-pd: Rename mu PD range to mu_a
soc: imx8: Add i.MX8MM UID(unique identifier) support
soc: imx8: Add i.MX8MQ UID(unique identifier) support
Link: https://lore.kernel.org/r/20190825153237.28829-1-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/drivers
soc: amlogic: updates for v5.4 (round 2)
- add power domain controller
* tag 'amlogic-drivers-2.1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
Link: https://patchwork.kernel.org/patch/11122205/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/drivers
cmdq helper:
reoder function parameter and change size of the parameters
* tag 'v5.3-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
soc: mediatek: cmdq: change the type of input parameter
soc: mediatek: cmdq: reorder the parameter
Link: https://lore.kernel.org/r/8c860e37-3816-d75f-fc37-ce496905ba73@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/drivers
soc: amlogic: driver updates for v5.4
Highlights
- clk-measure: support new S905X3 and A311D SoCs
- socinfo: support new S905X3 and A311D SoCs
* tag 'amlogic-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
soc: amlogic: meson-gx-socinfo: Add of_node_put() before return
soc: amlogic: clk-measure: Add support for SM1
dt-bindings: soc: amlogic: clk-measure: Add SM1 compatible
soc: amlogic: meson-gx-socinfo: Add SM1 and S905X3 IDs
soc: amlogic: meson-gx-socinfo: add A311D id
soc: amlogic: meson-clk-measure: add G12B second cluster cpu clk
soc: amlogic: meson-clk-measure: protect measure with a mutex
Link: https://lore.kernel.org/r/7h7e77cwv5.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.4
DPAA2 DPIO/MC driver
- Remove explicit device_link_remove() and device_link_del() calls due to
framework change
DPAA QBman driver
- Various changes to make it working with kexec
- Remove dev_err() usage after platform_get_irq()
GUTS driver
- Add LS1028 SoC support
* tag 'soc-fsl-next-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
bus: fsl-mc: remove explicit device_link_del
soc: fsl: dpio: remove explicit device_link_remove
soc: fsl: guts: Add definition for LS1028A
soc/fsl/qbman: Update device tree with reserved memory
soc/fsl/qbman: Fixup qman_shutdown_fq()
soc/fsl/qbman: Disable interrupts during portal recovery
soc/fsl/qbman: Fix drain_mr_fqni()
soc/fsl/qbman: Cleanup QMan queues if device was already initialized
soc/fsl/qbman: Cleanup buffer pools if BMan was initialized prior to bootup
soc/fsl/qbman: Rework QBMan private memory setup
soc: fsl: qbman: Remove dev_err() usage after platform_get_irq()
Link: https://lore.kernel.org/r/20190816195301.26660-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/drivers
Renesas driver updates for v5.4 (take two)
- Improve "always-on" PM Domain handling on SH/R-Mobile SoCs,
- Automatic errata selection for Cortex-A7/A9,
- Small fixes and improvements.
* tag 'renesas-drivers-for-v5.4-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
soc: renesas: Enable ARM_ERRATA_754322 for affected Cortex-A9
soc: renesas: Enable ARM_ERRATA_814220 for affected Cortex-A7
soc: renesas: rmobile-sysc: Set GENPD_FLAG_ALWAYS_ON for always-on domain
soc: renesas: rcar-sysc: Eliminate local variable gov
soc: renesas: rcar-sysc: Add goto to of_node_put() before return
Link: https://lore.kernel.org/r/20190823123643.18799-5-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/drivers
Samsung soc drivers changes for v5.4
Add Exynos Chipid driver for identification of product IDs and SoC
revisions. The driver also exposes chipid regmap, later to be used by
Exynos Adaptive Supply Voltage driver (adjusting voltages to different
revisions of same SoC).
* tag 'samsung-drivers-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: chipid: Convert exynos-chipid driver to use the regmap API
soc: samsung: Add exynos chipid driver support
Link: https://lore.kernel.org/r/20190816163042.6604-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The move of the IXP4xx SoC drivers exposed their config options on all
platforms.
Fix this by wrapping them inside an ARCH_IXP4XX or COMPILE_TEST block.
Link: https://lore.kernel.org/r/20190823090352.12243-1-linus.walleij@linaro.org
Fixes: fcf2d8978cd538a5 ("ARM: ixp4xx: Move NPE and QMGR to drivers/soc")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add support for the General Purpose Amlogic Everything-Else Power controller,
with the first support for G12A and SM1 SoCs dedicated to the VPU, PCIe,
USB, NNA, GE2D and Ethernet Power Domains.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The current code prints 'ret' (thus 0) while it should use 'err'.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to the cmdq hardware design, the subsys is u8,
the offset is u16 and the event id is u16.
This patch changes the type of subsys, offset and event id
to the correct type.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The order of gce instructions is [subsys offset value]
so reorder the parameter of cmdq_pkt_write_mask
and cmdq_pkt_write function.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
ARM Erratum 754322 affects Cortex-A9 revisions r2p* and r3p*.
Automatically enable support code to mitigate the erratum when compiling
a kernel for any of the affected Renesas SoCs:
- RZ/A1: r3p0,
- R-Mobile A1: r2p4,
- R-Car M1A: r2p2-00rel0,
- R-Car H1: r3p0,
- SH-Mobile AG5: r2p2.
EMMA Mobile EV2 (r1p3) and RZ/A2 (r4p1) are not affected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
ARM Erratum 814220 affects Cortex-A7 revisions r0p2-r0p5.
Automatically enable support code to mitigate the erratum when compiling
a kernel for any of the affected Renesas SoCs:
- R-Mobile APE6: r0p2,
- RZ/G1E: r0p5,
- RZ/G1C: r0p5,
- R-Car H2: r0p3,
- R-Car E2: r0p5,
- RZ/N1: r0p5.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Currently the R-Mobile "always-on" PM Domain is implemented by returning
-EBUSY from the generic_pm_domain.power_off() callback, and doing
nothing in the generic_pm_domain.power_on() callback. However, this
means the PM Domain core code is not aware of the semantics of this
special domain, leading to boot warnings like the following on
SH/R-Mobile SoCs:
sh_cmt e6130000.timer: PM domain c5 will not be powered off
Fix this by making the always-on nature of the domain explicit instead,
by setting the GENPD_FLAG_ALWAYS_ON flag. This removes the need for the
domain to provide power control callbacks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The chipid driver uses the MFD syscon API but it was not covered
properly in Kconfig.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
In commit 40d8aff614f7 ("soc: samsung: chipid: Convert exynos-chipid
driver to use the regmap API") of_find_compatible_node() call was
substituted with syscon_regmap_lookup_by_compatible() but also an error
log was added for case where lookup fails. On multiplatform the lookup
will always fail on any non-samsung device so the log is incorrect.
Remove the error log and just return an error code from
syscon_regmap_lookup_by_compatible() which internally calls
of_find_compatible_node().
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add AOSS QMP support for SM8150 and SC7180 SoCs.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Update max processor count to reflect the number of
co-processors on SC7180 SoCs.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The variable np in function meson_gx_socinfo_init takes the return value
of of_find_compatible_node, which gets a node but does not put it. If
this node is not put it may cause a memory leak. Hence put np after its
usefulness has been exhausted.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: a9daaba2965e ("soc: Add Amlogic SoC Information driver")
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the clk-measurer clocks IDs for the Amlogic SM1 SoC family.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the SoC IDs for the S905X3 Amlogic SM1 SoC.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Currently when the call to product_id_to_soc_id fails there
is a memory leak of soc_dev_attr->revision and soc_dev_attr
on the error return path. Fix this by adding a common error
return path that frees there obects and use this for two
error return paths.
Addresses-Coverity: ("Resource leak")
Fixes: 3253b7b7cd44 ("soc: samsung: Add exynos chipid driver support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
As of commit 980532a5dda319ee ("soc: renesas: rcar-sysc: Use
GENPD_FLAG_ALWAYS_ON"), the local variable "gov" is assigned just once,
so it can be eliminated.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
|
|
The local variable np in function rcar_sysc_pd_init takes the return
value of of_find_matching_node_and_match(), which gets a node but does
not put it. If np is not put before the function returns, it may cause
a memory leak.
Hence, remove the return statement that does not immediately follow a
putting of np. Replace it with a goto pointing to a pre-existing label
that first puts np and then returns the required value.
Issue found with Coccinelle.
Fixes: afa6f53df6052968 ("soc: renesas: rcar-sysc: Add support for fixing up power area tables")
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Starting with commit 72175d4ea4c4 ("driver core: Make driver core
own stateful device links") stateful device links are owned by the
driver core and should not be explicitly removed on device unbind.
Delete all device_link_remove appearances from the dpio driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
|
|
Adding compatible string "ls1028a-dcfg" to initialize guts driver
for ls1028 and SoC die attribute definition for LS1028A
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
|
|
When using the reserved memory node in the device tree there are
two options - dynamic or static. If a dynamic allocation was
selected (where the kernel selects the address for the allocation)
convert it to a static allocation by inserting the reg property.
This will ensure the same memory is reused after a kexec()
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
|
|
When shutting down a FQ on a dedicated channel only the
SW portal associated with that channel can dequeue from it.
Make sure the correct portal is use.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
|
|
Disable the QBMan interrupts during recovery.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
|
|
The drain_mr_fqni() function may be called fron uninterruptable
context so convert the msleep() to an mdelay(). Also ensure that
the valid bit is updated while polling.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
|
|
If the QMan device was previously initialized make sure all the
frame queues are out of service once all the portals are probed.
This handles the case where the kernel is restarted without the
SoC being reset (kexec for example)
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
|
|
Clean the BMan buffer pools if the device had been initialized
previously. This will ensure a consistent state if the kernel
was soft restarted (kexec for example)
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
|
|
Rework QBMan private memory setup so that the areas are not
zeroed if the device was previously initialized
If the QMan private memory was already initialized skip the PFDR
initialization.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
|
|
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Thierry Reding <treding@nvidia.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
|
|
Convert the driver to use regmap API in order to allow other
drivers, like ASV, to access the CHIPID registers.
Add definition of selected CHIPID register offsets and register bit
fields for Exynos5422 SoC.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Exynos SoCs have Chipid, for identification of product IDs and SoC
revisions. This patch intends to provide initialization code for all
these functionalities, at the same time it provides some sysfs entries
for accessing these information to user-space.
This driver uses existing binding for exynos-chipid.
Changes by Bartlomiej:
- fixed return values on errors
- removed bogus kfree_const()
- added missing Exynos4210 EVT0 id
- converted code to use EXYNOS_MASK define
- fixed np use after of_node_put()
- fixed too early use of dev_info()
- made driver fail for unknown SoC-s
- added SPDX tag
- updated Copyrights
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
[m.szyprowski: for suggestion and code snippet of product_id_to_soc_id]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[s.nawrocki: updated copyright date, removed uneeded headers inclusion]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omap variants for v5.3-rc cycle
We have another fix to disable voltage switching for am57xx SDIO as
the bootrom cannot handle all the voltages after a reset that thought
I had already sent a pull request for earlier but forgot. And we also
update dra74x iodelay configuration for mmc3 to use the recommended
values.
Then I noticed we had introduced few new boot warnings with the various
recent ti-sysc changes and wanted to fix those. I also noticed we still
have too many warnings to be able to spot the real ones easily and fixed
up few of those. Sure some of the warnings have been around for a long
time and few of the fixes could have waited for the merge window, but
having more usable dmesg log level output is a valuable.
Other fixes are IO size correction for am335x UARTs that cause issues
for at least FreeBSD using the same device tree file that checks that
the child IO range is not larger than the parent has.
For omap1 ams-delta keyboard we need to fix a irq ack that broke with
all the recent gpio changes.
And there are also few static checker warning fixes for recent am335x
PM changes and ti-sysc driver and one switch fall-though update.
* tag 'omap-for-v5.3/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: pm33xx: Make two symbols static
soc: ti: pm33xx: Fix static checker warnings
ARM: OMAP: dma: Mark expected switch fall-throughs
ARM: dts: Fix incomplete dts data for am3 and am4 mmc
bus: ti-sysc: Simplify cleanup upon failures in sysc_probe()
ARM: OMAP1: ams-delta-fiq: Fix missing irq_ack
ARM: dts: dra74x: Fix iodelay configuration for mmc3
ARM: dts: am335x: Fix UARTs length
ARM: OMAP2+: Fix omap4 errata warning on other SoCs
ARM: dts: Fix incorrect dcan register mapping for am3, am4 and dra7
ARM: dts: Fix flags for gpio7
bus: ti-sysc: Fix using configured sysc mask value
bus: ti-sysc: Fix handling of forced idle
ARM: OMAP2+: Fix missing SYSC_HAS_RESET_STATUS for dra7 epwmss
ARM: dts: am57xx: Disable voltage switching for SD card
Link: https://lore.kernel.org/r/pull-1565844391-332885@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into arm/soc
This is a slew of Ux500 updates for the v5.4 kernel cycle:
- Stop populating the PRCMU devices from the core CPU
file, it works just fine at device_initcall() level.
- Add a missing of_node_put() in the core file.
- Simplify the debug UART code.
- Add myself to MAINTAINERS
* tag 'ux500-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
MAINTAINERS: add soc/ux500
ARM: ux500: simplify and move debug UART
ARM: ux500: add missing of_node_put()
ARM: ux500: Stop populating the PRCMU devices early
Link: https://lore.kernel.org/r/CACRpkdbH-h5fRwuidcpeOp8mtRoKUW65SAk8a4A==BCDzn3QMA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/drivers
Renesas driver updates for v5.4
- Fix a flexible array member definition in the R-Car SYSC driver.
* tag 'renesas-drivers-for-v5.4-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
soc: renesas: rcar-sysc: Use [] to denote a flexible array member
Link: https://lore.kernel.org/r/20190802120355.1430-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fix sparse warnings:
drivers/soc/ti/pm33xx.c:144:27: warning: symbol 'rtc_wake_src' was not declared. Should it be static?
drivers/soc/ti/pm33xx.c:160:5: warning: symbol 'am33xx_rtc_only_idle' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The patch fixes a bunch of static checker warnings.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add i.MX SCU SoC's UID(unique identifier) support, user
can read it from sysfs:
root@imx8qxpmek:~# cat /sys/devices/soc0/soc_uid
7B64280B57AC1898
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
