| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
|
|
When booting with ACPI, the Geni Serial Engine is not set as the I2C/SPI
parent and thus, the wrapper (parent device) is unassigned. This causes
the kernel to crash with a null dereference error.
Link: https://lore.kernel.org/r/20190905082555.15020-1-lee.jones@linaro.org
Fixes: 8bc529b25354 ("soc: qcom: geni: Add support for ACPI")
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add AOSS QMP support for SM8150 and SC7180 SoCs.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Update max processor count to reflect the number of
co-processors on SC7180 SoCs.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Introduce fall through annotations in the switch statements of
socinfo_debugfs_init() to silence compiler warnings.
Acked-by: Vaishali Thakkar <vaishali.thakkar@linaro.org>
Fixes: 9c84c1e78634 ("soc: qcom: socinfo: Expose custom attributes")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
up the SoC.
The AOSS QMP driver is extended to communicate with the additional
resources. These resources are then registered as cooling devices
with the thermal framework.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The socinfo driver provides information about version of the various
images loaded in the system. Expose this to user space for debugging
purpose.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The Qualcomm socinfo provides a number of additional attributes,
add these to the socinfo driver and expose them via debugfs
functionality.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The Qualcomm socinfo driver exposes information about the SoC, its
version and its serial number to user space.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Imran Khan <kimran@codeaurora.org>
[Bjorn: Extract code to platform_driver, split patch in multiple]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[Vaishali: Simplify declarations, introduce qcom_socinfo struct, Fix
memory leak, Remove extra code and Misc code refactoring]
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (84 commits)
reset: remove redundant null check on pointer dev
soc: rockchip: work around clang warning
dt-bindings: reset: imx7: Fix the spelling of 'indices'
soc: imx: Add i.MX8MN SoC driver support
soc: aspeed: lpc-ctrl: Fix probe error handling
soc: qcom: geni: Add support for ACPI
firmware: ti_sci: Fix gcc unused-but-set-variable warning
firmware: ti_sci: Use the correct style for SPDX License Identifier
soc: imx8: Use existing of_root directly
soc: imx8: Fix potential kernel dump in error path
firmware/psci: psci_checker: Park kthreads before stopping them
memory: move jedec_ddr.h from include/memory to drivers/memory/
memory: move jedec_ddr_data.c from lib/ to drivers/memory/
MAINTAINERS: Remove myself as qcom maintainer
soc: aspeed: lpc-ctrl: make parameter optional
soc: qcom: apr: Don't use reg for domain id
soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
memory: tegra: Fix -Wunused-const-variable
firmware: tegra: Early resume BPMP
soc/tegra: Select pinctrl for Tegra194
...
|
|
Pull remoteproc updates from Bjorn Andersson:
"This adds support for the STM32 remoteproc, additional i.MX platforms
with Cortex M4 remoteprocs and Qualcomm's QCS404 Compute DSP.
Also initial support for vendor specific resource table entries and
support for unprocessed Qualcomm firmware files"
* tag 'rproc-v5.3' of git://github.com/andersson/remoteproc:
remoteproc: stm32: fix building without ARM SMCC
remoteproc: qcom: q6v5-mss: Fix build error without QCOM_MDT_LOADER
remoteproc: copy parent dma_pfn_offset for vdev
remoteproc: qcom: q6v5-mss: Support loading non-split images
soc: qcom: mdt_loader: Support loading non-split images
remoteproc: stm32: add an ST stm32_rproc driver
dt-bindings: remoteproc: add bindings for stm32 remote processor driver
dt-bindings: stm32: add bindings for ML-AHB interconnect
remoteproc: Use struct_size() helper
remoteproc: add vendor resources handling
remoteproc: imx: Fix typo in "failed"
remoteproc: imx: Broaden the Kconfig selection logic
remoteproc,rpmsg: add missing MAINTAINERS file entries
remoteproc: qcom: qdsp6-adsp: Add support for QCS404 CDSP
dt-bindings: remoteproc: Rename and amend Hexagon v56 binding
|
|
In some software releases the firmware images are not split up with each
loadable segment in it's own file. Check the size of the loaded firmware
to see if it still contains each segment to be loaded, before falling
back to the split-out segments.
Acked-by: Andy Gross <agross@kernel.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm ARM Based Driver Updates for v5.3
* Add ACPI support to Qualcomm GENI SE
* Update Qualcomm Maintainers entry to remove David Brown as maintainer and
fixup typos and incorrect DT file entry
* Fixup APR domain id usage and making callbacks in non-atomic context
* Add AOSS QMP driver and bindings
* Add power domains for MSM8998 and QCS404 in QCOM RPMPD
* Add corner macros, max state support, and fixups for setting performance state
for Qcom RPMPD
* tag 'qcom-drivers-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: geni: Add support for ACPI
MAINTAINERS: Remove myself as qcom maintainer
soc: qcom: apr: Don't use reg for domain id
soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
soc: qcom: Add AOSS QMP driver
dt-bindings: soc: qcom: Add AOSS QMP binding
qcom: apr: Make apr callbacks in non-atomic context
soc: qcom: rpmpd: Add MSM8998 power-domains
dt-bindings: power: Add rpm power domain bindings for msm8998
soc: qcom: rpmpd: Add QCS404 power-domains
dt-bindings: power: Add rpm power domain bindings for qcs404
soc: qcom: rpmpd: Modify corner defining macros
soc: qcom: rpmpd: Add support to set rpmpd state to max
soc: qcom: rpmpd: fixup rpmpd set performance state
MAINTAINER: Fix Qualcomm ETHQOS ethernet DT file
MAINTAINERS: fix typo in file name
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When booting with ACPI as the active set of configuration tables,
all; clocks, regulators, pin functions ect are expected to be at
their ideal values/levels/rates, thus the associated frameworks
are unavailable. Ensure calls to these APIs are shielded when
ACPI is enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
|
|
When booting with ACPI as the active set of configuration tables,
all; clocks, regulators, pin functions ect are expected to be at
their ideal values/levels/rates, thus the associated frameworks
are unavailable. Ensure calls to these APIs are shielded when
ACPI is enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The reg property represents the address and size on the bus that a
device lives, but for APR the parent is a rpmsg bus, which does not have
numerical addresses. Simply defining #address/#size-cells to 1 and 0,
respectively, to silence the compiler is not an appropriate solution.
Replace the use of "reg" with an APR specific property.
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Fix Kconfig warning and subsequent build errors that are caused
when PM_GENERIC_DOMAINS=y but CONFIG_PM is not set/enabled.
WARNING: unmet direct dependencies detected for PM_GENERIC_DOMAINS
Depends on [n]: PM [=n]
Selected by [m]:
- QCOM_AOSS_QMP [=m] && (ARCH_QCOM || COMPILE_TEST [=y]) && MAILBOX [=y] && COMMON_CLK [=y]
Fixes these build errors:
../drivers/base/power/domain.c: In function ‘genpd_queue_power_off_work’:
../drivers/base/power/domain.c:485:13: error: ‘pm_wq’ undeclared (first use in this function)
queue_work(pm_wq, &genpd->power_off_work);
../drivers/base/power/domain.c:485:13: note: each undeclared identifier is reported only once for each function it appears in
../drivers/base/power/domain.c: In function ‘genpd_dev_pm_qos_notifier’:
../drivers/base/power/domain.c:675:25: error: ‘struct dev_pm_info’ has no member named ‘ignore_children’
if (!dev || dev->power.ignore_children)
../drivers/base/power/domain.c: In function ‘rtpm_status_str’:
../drivers/base/power/domain.c:2754:16: error: ‘struct dev_pm_info’ has no member named ‘runtime_error’
if (dev->power.runtime_error)
../drivers/base/power/domain.c:2756:21: error: ‘struct dev_pm_info’ has no member named ‘disable_depth’
else if (dev->power.disable_depth)
../drivers/base/power/domain.c:2758:21: error: ‘struct dev_pm_info’ has no member named ‘runtime_status’
else if (dev->power.runtime_status < ARRAY_SIZE(status_lookup))
../drivers/base/power/domain.c:2759:31: error: ‘struct dev_pm_info’ has no member named ‘runtime_status’
p = status_lookup[dev->power.runtime_status];
../drivers/base/power/domain_governor.c: In function ‘default_suspend_ok’:
../drivers/base/power/domain_governor.c:82:17: error: ‘struct dev_pm_info’ has no member named ‘ignore_children’
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The Always On Subsystem (AOSS) Qualcomm Messaging Protocol (QMP) driver
is used to communicate with the AOSS for certain side-channel requests,
that are not available through the RPMh interface.
The communication is a very simple synchronous mechanism of messages
being written in message RAM and a doorbell in the AOSS is rung. As the
AOSS has processed the message length is cleared and an interrupt is
fired by the AOSS as acknowledgment.
The driver exposes the QDSS clock as a clock and the low-power state
associated with the remoteprocs in the system as a set of power-domains.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
APR communication with DSP is not atomic in nature.
Its request-response type. Trying to pretend that these are atomic
and invoking apr client callbacks directly under atomic/irq context has
endless issues with soundcard. It makes more sense to convert these
to nonatomic calls. This also coverts all the dais to be nonatomic.
All the callbacks are now invoked as part of rx work queue.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license rev 2 and only
rev 2 as published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190112.583753585@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the shared cx/mx and sensor sub-system's cx and mx
power-domains found on MSM8998.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
|
|
Add the shared cx/mx and the low-power-island's cx and mx power-domains
found on QCS404.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sibi: Fixup corner/vfc with vlfl/vfl]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
|
|
QCS404 uses individual resource type magic for each power-domain, so
adjust the macros slightly to make them reusable for this.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sibi: Extend rpmpd corner pair to a generic rpmpd pair]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
|
|
rpmpd max state varies across SoCs and SoC families, add support
in the driver to make it SoC/SoC family specific
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
|
|
Remoteproc q6v5-mss calls set_performance_state with INT_MAX on
rpmpd. This is currently ignored since it is greater than the
max supported state. Fixup rpmpd state to max if the required
state is greater than all the supported states.
Fixes: 075d3db8d10d ("soc: qcom: rpmpd: Add support for get/set performance state")
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The return index value from bitmap_find_next_zero_area can be higher
than available slot. So correct the check to return error in such case.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Andy Gross <agross@kernel.org>
|
|
The memremap() function doesn't return error pointers, it returns NULL.
This code is returning "ret = PTR_ERR(NULL);" which is success, but it
should return -ENOMEM.
Fixes: 312416d9171a ("drivers: qcom: add command DB driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Current QMI clients are not userspace facing, if their threads are
signaled, they do not do any signal checking or propagate the
ERESTARTSYS return code up. Remove the interruptible option so clients
can finish their QMI transactions even if the thread is signaled.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Chris Lew <clew@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This change adds mmap functionality to rmtfs_mem driver.
Userspace application can map the address and use this
mapped address directly as buffer for read/write call to disk.
and avoid the read/write call to the shared path to copy the
buffer to userspace application.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ankit Jain <jankit@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch fixes typos in the llcc-slice driver.
Fixes: 72d1cd033154 ("qcom: soc: llcc-slice: Clear the global drv_data pointer on error")
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Make the code a little bit clearer (and use less gotos)
by consolidating some of the initialization.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Currently the data structure for llc-slice is devm allocated and
stored as a global but never cleared if the probe function fails.
This is a problem because devm managed memory gets freed on probe
failure the API functions could access the pointer after it has been
freed.
Initialize the drv_data pointer to an error and reset it to an error
on probe failure or device destroy and add protection to the API
functions to make sure the memory doesn't get accessed.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add the compatible for the RPM in SDM660, so that rpm resources can be
made available.
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
If of_platform_populate() fails in gsbi_probe(),
gsbi->hclk is left undisabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Using the batch API from the interconnect driver sometimes leads to a
KASAN error due to an access to freed memory. This is easier to trigger
with threadirqs on the kernel commandline.
BUG: KASAN: use-after-free in rpmh_tx_done+0x114/0x12c
Read of size 1 at addr fffffff51414ad84 by task irq/110-apps_rs/57
CPU: 0 PID: 57 Comm: irq/110-apps_rs Tainted: G W 4.19.10 #72
Call trace:
dump_backtrace+0x0/0x2f8
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0xcc/0x10c
print_address_description+0x74/0x240
kasan_report+0x250/0x26c
__asan_report_load1_noabort+0x20/0x2c
rpmh_tx_done+0x114/0x12c
tcs_tx_done+0x450/0x768
irq_forced_thread_fn+0x58/0x9c
irq_thread+0x120/0x1dc
kthread+0x248/0x260
ret_from_fork+0x10/0x18
Allocated by task 385:
kasan_kmalloc+0xac/0x148
__kmalloc+0x170/0x1e4
rpmh_write_batch+0x174/0x540
qcom_icc_set+0x8dc/0x9ac
icc_set+0x288/0x2e8
a6xx_gmu_stop+0x320/0x3c0
a6xx_pm_suspend+0x108/0x124
adreno_suspend+0x50/0x60
pm_generic_runtime_suspend+0x60/0x78
__rpm_callback+0x214/0x32c
rpm_callback+0x54/0x184
rpm_suspend+0x3f8/0xa90
pm_runtime_work+0xb4/0x178
process_one_work+0x544/0xbc0
worker_thread+0x514/0x7d0
kthread+0x248/0x260
ret_from_fork+0x10/0x18
Freed by task 385:
__kasan_slab_free+0x12c/0x1e0
kasan_slab_free+0x10/0x1c
kfree+0x134/0x588
rpmh_write_batch+0x49c/0x540
qcom_icc_set+0x8dc/0x9ac
icc_set+0x288/0x2e8
a6xx_gmu_stop+0x320/0x3c0
a6xx_pm_suspend+0x108/0x124
adreno_suspend+0x50/0x60
cr50_spi spi5.0: SPI transfer timed out
pm_generic_runtime_suspend+0x60/0x78
__rpm_callback+0x214/0x32c
rpm_callback+0x54/0x184
rpm_suspend+0x3f8/0xa90
pm_runtime_work+0xb4/0x178
process_one_work+0x544/0xbc0
worker_thread+0x514/0x7d0
kthread+0x248/0x260
ret_from_fork+0x10/0x18
The buggy address belongs to the object at fffffff51414ac80
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 260 bytes inside of
512-byte region [fffffff51414ac80, fffffff51414ae80)
The buggy address belongs to the page:
page:ffffffbfd4505200 count:1 mapcount:0 mapping:fffffff51e00c680 index:0x0 compound_mapcount: 0
flags: 0x4000000000008100(slab|head)
raw: 4000000000008100 ffffffbfd4529008 ffffffbfd44f9208 fffffff51e00c680
raw: 0000000000000000 0000000000200020 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
fffffff51414ac80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
fffffff51414ad00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>fffffff51414ad80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
fffffff51414ae00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
fffffff51414ae80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
The batch API sets the same completion for each rpmh message that's sent
and then loops through all the messages and waits for that single
completion declared on the stack to be completed before returning from
the function and freeing the message structures. Unfortunately, some
messages may still be in process and 'stuck' in the TCS. At some later
point, the tcs_tx_done() interrupt will run and try to process messages
that have already been freed at the end of rpmh_write_batch(). This will
in turn access the 'needs_free' member of the rpmh_request structure and
cause KASAN to complain. Furthermore, if there's a message that's
completed in rpmh_tx_done() and freed immediately after the complete()
call is made we'll be racing with potentially freed memory when
accessing the 'needs_free' member:
CPU0 CPU1
---- ----
rpmh_tx_done()
complete(&compl)
wait_for_completion(&compl)
kfree(rpm_msg)
if (rpm_msg->needs_free)
<KASAN warning splat>
Let's fix this by allocating a chunk of completions for each message and
waiting for all of them to be completed before returning from the batch
API. Alternatively, we could wait for the last message in the batch, but
that may be a more complicated change because it looks like
tcs_tx_done() just iterates through the indices of the queue and
completes each message instead of tracking the last inserted message and
completing that first.
Fixes: c8790cb6da58 ("drivers: qcom: rpmh: add support for batch RPMH request")
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: "Raju P.L.S.S.S.N" <rplsssn@codeaurora.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: stable@vger.kernel.org
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Fix the redundant call being made to send the sleep and wake requests
immediately to the controller.
As per the patch [1], the sleep and wake request votes are cached in
rpmh controller and sent during rpmh_flush(). These requests needs to be
sent only during entry of deeper system low power modes or suspend.
[1] https://patchwork.kernel.org/patch/10477533/
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
In order to run an rmtfs daemon as an unprivileged user, that user would
need access to the phys_addr and size sysfs attributes. Sharing these
attributes with unprivileged users doesn't really leak anything
sensitive, since if you have access to physical memory, the jig is
up anyway.
Make those attributes readable by all.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Currently the qcom_rmtfs_memN devices are entirely invisible to the udev world.
Add a class to the rmtfs device so that uevents fire when the device is added.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Since QCOM_RPMPD is bool and it depends on QCOM_SMD_RPM
which is tristate, configurations such as arm64:allmodconfig
result in
CONFIG_QCOM_RPMPD=y
CONFIG_QCOM_SMD_RPM=m
This in turn results in
drivers/soc/qcom/rpmpd.o: In function `rpmpd_send_corner':
rpmpd.c:(.text+0x10c): undefined reference to `qcom_rpm_smd_write'
drivers/soc/qcom/rpmpd.o: In function `rpmpd_power_on':
rpmpd.c:(.text+0x3b4): undefined reference to `qcom_rpm_smd_write'
drivers/soc/qcom/rpmpd.o: In function `rpmpd_power_off':
rpmpd.c:(.text+0x520): undefined reference to `qcom_rpm_smd_write'
make: *** [vmlinux] Error 1
Fix it by making QCOM_RPMPD depend on QCOM_SMD_RPM=y
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The MFD_QCOM_RPM is the RPM in family A, but the rpmpd driver only implements
support for SMD based devices. Drop the dependency and remove includes of the
family A headers. No functional change.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Specify the active + sleep and active-only MX power domains as
the parents of the corresponding CX power domains. This will ensure that
performance state requests on CX automatically generate equivalent requests
on MX power domains.
This is used to enforce a requirement that exists for various
hardware blocks on SDM845 that MX performance state >= CX performance
state for a given operating frequency.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The RPMh power domain driver aggregates the corner votes from various
consumers for the ARC resources and communicates it to RPMh.
With RPMh we use 2 different numbering space for corners, one used
by the clients to express their performance needs, and another used
to communicate to RPMh hardware.
The clients express their performance requirements using a sparse
numbering space which are mapped to meaningful levels like RET, SVS,
NOMINAL, TURBO etc which then get mapped to another number space
between 0 and 15 which is communicated to RPMh. The sparse number space,
also referred to as vlvl is mapped to the continuous number space of 0
to 15, also referred to as hlvl, using command DB.
Some power domain clients could request a performance state only while
the CPU is active, while some others could request for a certain
performance state all the time regardless of the state of the CPU.
We handle this by internally aggregating the votes from both type of
clients and then send the aggregated votes to RPMh.
There are also 3 different types of votes that are comunicated to RPMh
for every resource.
1. ACTIVE_ONLY:
This specifies the requirement for the resource when the CPU is
active
2. SLEEP:
This specifies the requirement for the resource when the CPU is
going to sleep
3. WAKE_ONLY:
This specifies the requirement for the resource when the CPU is
coming out of sleep to active state
We add data for all power domains on sdm845 SoC as part of the patch.
The driver can be extended to support other SoCs which support RPMh
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add support for the .set_performace_state() and .opp_to_performance_state()
callbacks in the rpmpd driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The Power domains for corners just pass the performance state set by the
consumers to the RPM (Remote Power manager) which then takes care
of setting the appropriate voltage on the corresponding rails to
meet the performance needs.
We add all power domain data needed on msm8996 here. This driver can easily
be extended by adding data for other qualcomm SoCs as well.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch adds a compatible for the rpm on the Qualcomm QCS404 platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Let's change the function signature to return the pointer to memory or
an error pointer on failure, and take an argument that lets us return
the size of the aux data read. This way we can remove the
cmd_db_read_aux_data_len() API entirely and also get rid of the memcpy
operation from cmd_db to the caller. Updating the only user of this code
shows that making this change allows us to remove a function and put the
lookup where the user is.
Cc: Mahesh Sivasubramanian <msivasub@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
