| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Conflicts:
arch/arm/mm/init.c
|
|
Found in the Versatile build:
WARNING: drivers/built-in.o(.data+0x14c): Section mismatch in reference from the variable pl061_gpio_driver to the (unknown reference) .init.data:(unknown)
The variable pl061_gpio_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x40f8): Section mismatch in reference from the variable pl011_driver to the (unknown reference) .init.data:(unknown)
The variable pl011_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x5ab4): Section mismatch in reference from the variable pl031_driver to the (unknown reference) .init.data:(unknown)
The variable pl031_driver references
the (unknown reference) __initdata (unknown)
Basically, amba_id structures must not be __initdata. Also fix:
WARNING: drivers/built-in.o(.data+0x138): Section mismatch in reference from the variable pl061_gpio_driver to the function .init.text:pl061_probe()
The variable pl061_gpio_driver references
the function __init pl061_probe()
which is an incorrectly annotated probe function. Fix it to reflect
the other AMBA bus probe functions by removing the __init attributation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Implementation of the ST-Ericsson baudrate extension in the PL011
block. In this modified variant it is possible to change the
sampling factor from 16 to 8, and thanks to this we can get higher
baudrates while still using the same peripheral clock.
Also replace the simple division to determine the baud divisor
with DIV_ROUND_CLOSEST() rather than a simple integer division.
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Jerzy Kasenberg <jerzy.kasenberg@tieto.com>
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In the ST-Ericsson version of the PL011 the TX and RX have different
control registers.
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch fixes a build failure [1-4] in the atmel_serial code introduced by
patch the patch ARM: 6092/1: atmel_serial: support for RS485
communications (e8faff7330a3501eafc9bfe5f4f15af444be29f5)
The build failure was caused by missing struct field and missing defines
for the avr32 board - the patch fixes this.
[1] http://kisskb.ellerman.id.au/kisskb/buildresult/2575242/ - first failure in linux-next, may 11th
[2] http://kisskb.ellerman.id.au/kisskb/buildresult/2816418/ - still exists as of today
[3] http://kisskb.ellerman.id.au/kisskb/buildresult/2617511/ - first failure in Linus' tree - May 20th - did really no one notice this?!
[4] http://kisskb.ellerman.id.au/kisskb/buildresult/2813956/ - still exists in Linus' tree as of today
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
math-emu: correct test for downshifting fraction in _FP_FROM_INT()
perf: Add DWARF register lookup for sparc
MAINTAINERS: Add SBUS driver path to sparc entry.
drivers/sbus: Remove unnecessary casts of private_data
sparc: remove homegrown L1_CACHE_ALIGN macro
sparc64: fix the build error due to smp_kgdb_capture_client()
sparc64: Fix maybe_change_configuration() PCR setting.
arch/sparc/kernel: Eliminate what looks like a NULL pointer dereference
sparc64: Update defconfig.
sunsu: Fix use after free in su_remove().
sunserial: Don't call add_preferred_console() when console= is specified.
sparc32: Kill none_mask, it's bogus.
|
|
Fix typo in comments. Replace charater with character.
Characteristics too.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The cpm_uart_early_write() function which was used for console poll
isn't implemented in the cpm uart driver.
Implementing this function both fixes the build when CONFIG_CONSOLE_POLL
is set and allows kgdboc to work via the cpm uart.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Reviewed-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (52 commits)
phylib: Add autoload support for the LXT973 phy.
ISDN: hysdn, fix potential NULL dereference
vxge: fix memory leak in vxge_alloc_msix() error path
isdn/gigaset: correct CAPI connection state storage
isdn/gigaset: encode HLC and BC together
isdn/gigaset: correct CAPI DATA_B3 Delivery Confirmation
isdn/gigaset: correct CAPI voice connection encoding
isdn/gigaset: honor CAPI application's buffer size request
cpmac: do not leak struct net_device on phy_connect errors
smc91c92_cs: fix the problem that lan & modem does not work simultaneously
ipv6: fix NULL reference in proxy neighbor discovery
Bluetooth: Bring back var 'i' increment
xfrm: check bundle policy existance before dereferencing it
sky2: enable rx/tx in sky2_phy_reinit()
cnic: Disable statistics initialization for eth clients that do not support statistics
net: add dependency on fw class module to qlcnic and netxen_nic
snmp: fix SNMP_ADD_STATS()
hso: remove setting of low_latency flag
udp: Fix bogus UFO packet generation
lasi82596: fix netdev_mc_count conversion
...
|
|
|
|
pcnet_cs:
serial_cs:
add new id (TOSHIBA Modem/LAN Card)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
serial: add support for various Titan PCI cards
Models: 200I, 400I, 800I, 400EH, 800EH, 800EHB,
100E, 200E, 400E, 800E, 200EI, 200EISI
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
altera_uart_remove should be in .devexit.text
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The check for the TRDY flag after writing the character is not needed.
Also do a cpu_relax() inside the loop.
Pass a struct uart_port to altera_uart_console_putc, so we do not need
to get it (and dereference pointers) for every character.
Cc: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Don't take the port spinlock in uart functions where the serial core
already takes care of locking/unlocking them.
The code would actually lock up on architectures where spinlocks are
implemented (not the case on nios2 where this driver is primarily used
for now, thus this bug didn't trigger).
Also protect calling altera_uart_rx_chars/altera_uart_tx_chars in the
interrupt handler by the port spinlock.
Thanks to Ian Abbott for pointing these issues out.
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This most likely won't cause problems on systems as people don't typically
enable GPIO RTS/CTS if they don't actually use it.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Anomaly 05000230 (over sampling of the UART STOP bit) applies only when
the peripheral is operating in UART mode. So drop the anomaly handling
when the UART is in IRDA mode.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Set the mnd counter based on uartclk. This fixes a problem
on 7x30 where the uartclk is 19.2Mhz rather than the usual
4.8Mhz.
Trout incorrectly reports uartclk to be running at 19.2Mhz
It is actually running at 4.8Mhz. For trout force mnd
counter values as if uartclk was fed by tcxo/4.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
[dwalker@codeaurora.org: inlined, moved into header, added comments.]
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Grant patches added an of mach table to struct device_driver. However,
while he changed the macio device code to use that, he left the match
table pointer in struct macio_driver and didn't update drivers to use
the "new" one, thus breaking the probing.
This completes the change by moving all drivers to setup the "new"
one, removing all traces of the old one, and while at it (since it
changes the exact same locations), I also remove two other duplicates
from struct driver which are the name and owner fields.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Rename the structure to avoid the following warning:
WARNING: drivers/serial/built-in.o(.data+0x534): Section mismatch in reference from the variable s5p_serial_drv to the function .devexit.text:s3c24xx_serial_remove()
The variable s5p_serial_drv references
the function __devexit s3c24xx_serial_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Real serial port 'up' objects are statically allocated from an
array in the driver. Keyboard and mouse ports, on the other
hand, are dynamically allocated.
Unfortunately, we free these dynamic 'up' objects before we unmap the
I/O registers.
Rearrange su_remove() so that this does not happen.
Noticed by Julia Lawall.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/xilinx: Fix compile error
spi/davinci: Fix clock prescale factor computation
spi: move bitbang txrx utility functions to private header
spi/mpc5121: Add SPI master driver for MPC5121 PSC
powerpc/mpc5121: move PSC FIFO memory init to platform code
spi/ep93xx: implemented driver for Cirrus EP93xx SPI controller
Documentation/spi/* compile warning fix
spi/omap2_mcspi: Check params before dereference or use
spi/omap2_mcspi: add turbo mode support
spi/omap2_mcspi: change default DMA_MIN_BYTES value to 160
spi/pl022: fix stop queue procedure
spi/pl022: add support for the PL023 derivate
spi/pl022: fix up differences between ARM and ST versions
spi/spi_mpc8xxx: Do not use map_tx_dma to unmap rx_dma
spi/spi_mpc8xxx: Fix QE mode Litte Endian
spi/spi_mpc8xxx: fix potential memory corruption.
|
|
Commit 8b505ca8e2600eb9e7dd2d6b2682a81717671374 ("serial: 68328serial.c:
remove BAUD_TABLE_SIZE macro") misses one use of BAUD_TABLE_SIZE. So the
resulting 68328serial.c does not compile:
drivers/serial/68328serial.c: In function `m68328_console_setup':
drivers/serial/68328serial.c:1439: error: `BAUD_TABLE_SIZE' undeclared (first use in this function)
drivers/serial/68328serial.c:1439: error: (Each undeclared identifier is reported only once
drivers/serial/68328serial.c:1439: error: for each function it appears in.)
Fix that last use of it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Cc: Thiago Farina <tfransosi@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
Since PSC could also be used in other modes than UART mode
we move PSC FIFO memory initialization from serial driver to
common platform code. The initialized FIFO memory slices may
not overlap, so the most easy way would be to configure them
all at once at init time for all PSC devices. This is now done
by this patch.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (25 commits)
sh: fix up sh7785lcr_32bit_defconfig.
arch/sh/lib/strlen.S: Checkpatch cleanup
sh: fix up sh7786 dmaengine build.
sh: guard cookie consistency across termination in the DMA driver
sh: prevent the DMA driver from unloading, while in use
sh: fix Oops in the serial SCI driver
sh: allow platforms to specify SD-card supported voltages
mmc: let MFD's provide supported Vdd card voltages to tmio_mmc
sh: disable SD-card write-protection detection on kfr2r09
mfd: pass platform flags down to the tmio_mmc driver
tmio: add a platform flag to disable card write-protection detection
sh: Add SDHI DMA support to migor
sh: Add SDHI DMA support to kfr2r09
sh: Add SDHI DMA support to ms7724se
sh: Add SDHI DMA support to ecovec
mmc: add DMA support to tmio_mmc driver, when used on SuperH
sh: prepare the SDHI MFD driver to pass DMA configuration to tmio_mmc.c
mmc: prepare tmio_mmc for passing of DMA configuration from the MFD cell
sh: add DMA slave definitions to sh7724
sh: add DMA slaves for two SDHI controllers to sh7722
...
|
|
Fix an Oops, triggering, if the DMA buffer allocation for the Rx channel in
sh-sci.c fails.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
DMAENGINE: extend the control command to include an arg
async_tx: trim dma_async_tx_descriptor in 'no channel switch' case
DMAENGINE: DMA40 fix for allocation of logical channel 0
DMAENGINE: DMA40 support paused channel status
dmaengine: mpc512x: Use resource_size
DMA ENGINE: Do not reset 'private' of channel
ioat: Remove duplicated devm_kzalloc() calls for ioatdma_device
ioat3: disable cacheline-unaligned transfers for raid operations
ioat2,3: convert to producer/consumer locking
ioat: convert to circ_buf
DMAENGINE: Support for ST-Ericssons DMA40 block v3
async_tx: use of kzalloc/kfree requires the include of slab.h
dmaengine: provide helper for setting txstate
DMAENGINE: generic channel status v2
DMAENGINE: generic slave control v2
dma: timb-dma: Update comment and fix compiler warning
dma: Add timb-dma
DMAENGINE: COH 901 318 fix bytesleft
DMAENGINE: COH 901 318 rename confusing vars
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (92 commits)
powerpc: Remove unused 'protect4gb' boot parameter
powerpc: Build-in e1000e for pseries & ppc64_defconfig
powerpc/pseries: Make request_ras_irqs() available to other pseries code
powerpc/numa: Use ibm,architecture-vec-5 to detect form 1 affinity
powerpc/numa: Set a smaller value for RECLAIM_DISTANCE to enable zone reclaim
powerpc: Use smt_snooze_delay=-1 to always busy loop
powerpc: Remove check of ibm,smt-snooze-delay OF property
powerpc/kdump: Fix race in kdump shutdown
powerpc/kexec: Fix race in kexec shutdown
powerpc/kexec: Speedup kexec hash PTE tear down
powerpc/pseries: Add hcall to read 4 ptes at a time in real mode
powerpc: Use more accurate limit for first segment memory allocations
powerpc/kdump: Use chip->shutdown to disable IRQs
powerpc/kdump: CPUs assume the context of the oopsing CPU
powerpc/crashdump: Do not fail on NULL pointer dereferencing
powerpc/eeh: Fix oops when probing in early boot
powerpc/pci: Check devices status property when scanning OF tree
powerpc/vio: Switch VIO Bus PM to use generic helpers
powerpc: Avoid bad relocations in iSeries code
powerpc: Use common cpu_die (fixes SMP+SUSPEND build)
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb
* 'dbg-early-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
echi-dbgp: Add kernel debugger support for the usb debug port
earlyprintk,vga,kdb: Fix \b and \r for earlyprintk=vga with kdb
kgdboc: Add ekgdboc for early use of the kernel debugger
x86,early dr regs,kgdb: Allow kernel debugger early dr register access
x86,kgdb: Implement early hardware breakpoint debugging
x86, kgdb, init: Add early and late debug states
x86, kgdb: early trap init for early debug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb
* 'kdb-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb: (25 commits)
kdb,debug_core: Allow the debug core to receive a panic notification
MAINTAINERS: update kgdb, kdb, and debug_core info
debug_core,kdb: Allow the debug core to process a recursive debug entry
printk,kdb: capture printk() when in kdb shell
kgdboc,kdb: Allow kdb to work on a non open console port
kgdb: Add the ability to schedule a breakpoint via a tasklet
mips,kgdb: kdb low level trap catch and stack trace
powerpc,kgdb: Introduce low level trap catching
x86,kgdb: Add low level debug hook
kgdb: remove post_primary_code references
kgdb,docs: Update the kgdb docs to include kdb
kgdboc,keyboard: Keyboard driver for kdb with kgdb
kgdb: gdb "monitor" -> kdb passthrough
sparc,sunzilog: Add console polling support for sunzilog serial driver
sh,sh-sci: Use NO_POLL_CHAR in the SCIF polled console code
kgdb,8250,pl011: Return immediately from console poll
kgdb: core changes to support kdb
kdb: core for kgdb back end (2 of 2)
kdb: core for kgdb back end (1 of 2)
kgdb,blackfin: Add in kgdb_arch_set_pc for blackfin
...
|
|
Use the resource_size function instead of manually calculating the
resource size. This actually fixes an off-by-one error.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add an UART driver for the UART component available as a SOPC (System on
Programmable Chip) component for Altera FPGAs.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add an UART driver for the JTAG UART component available as a SOPC
(System on Programmable Chip) component for Altera FPGAs.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix a problem in early versions of the FPGA IP.
In certain situations the IP reports that the FIFO is empty, but a byte is
still clocked out. If a flush is done at that point the currently clocked
byte is canceled.
This causes incompatibilities with the upper layers when a port is closed,
it waits until the FIFO is empty and then closes the port. During close
the FIFO is flushed -> the last byte is not sent properly.
Now the FIFO is only flushed if it is reported to be non-empty. Which
makes the currently clocked out byte to finish.
[akpm@linux-foundation.org: fix build]
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
CTS is a read only bit and we are to stop signal RTS if modem line
TIOCM_RTS is not set.
Thanks for suggestions by Richard Röjfors.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Byte accesses for I/O devices in Xilinx IP is going to be less
desired in the future such that the driver is being changed to
use 32 bit accesses.
This change facilitates using the uartlite IP over a PCIe bus
which only allows 32 bit accesses.
Signed-off-by: John Linn <john.linn@xilinx.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The BF54xM procs imply the related BF54x define, so no need to check both.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Should be stable now ...
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Now that the SPORT MMR defines have been unified, switch over to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Rather than always turn on the SPORT TX interrupt, only do it when we've
actually queued up data for transmission. This avoids useless interrupt
processing.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
These were all copied over from the Blackfin UART driver, but they don't
make sense here because these bits are all specific to the Blackfin UART.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
