| Age | Commit message (Collapse) | Author |
|---|
|
It used to be that minors where 8 bit. But now they
are actually 20 bit. So the fix is simplicity itself.
I've tested with 300 devices and all user-mode utils
work just fine. I have also mechanically added 10,000
to the ida (so devices are /dev/osd10000, /dev/osd10001 ...)
and was able to mkfs an exofs filesystem and access osds
from user-mode.
All the open-osd user-mode code uses the same library
to access devices through their symbolic names in
/dev/osdX so I'd say it's pretty safe. (Well tested)
This patch is very important because some of the systems
that will be deploying the 3.2 pnfs-objects code are larger
than 64 OSDs and will stop to work properly when reaching
that number.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
SCSI fixes on 20120224:
"This is a set of assorted bug fixes for power management, mpt2sas,
ipr, the rdac device handler and quite a big chunk for qla2xxx (plus a
use after free of scsi_host in scsi_scan.c). "
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] scsi_dh_rdac: Fix for unbalanced reference count
[SCSI] scsi_pm: Fix bug in the SCSI power management handler
[SCSI] scsi_scan: Fix 'Poison overwritten' warning caused by using freed 'shost'
[SCSI] qla2xxx: Update version number to 8.03.07.13-k.
[SCSI] qla2xxx: Proper detection of firmware abort error code for ISP82xx.
[SCSI] qla2xxx: Remove resetting memory during device initialization for ISP82xx.
[SCSI] qla2xxx: Complete mailbox command timedout to avoid initialization failures during next reset cycle.
[SCSI] qla2xxx: Remove check for null fcport from host reset handler.
[SCSI] qla2xxx: Correct out of bounds read of ISP2200 mailbox registers.
[SCSI] qla2xxx: Remove errant clearing of MBX_INTERRUPT flag during CT-IOCB processing.
[SCSI] qla2xxx: Clear options-flags while issuing stop-firmware mbx command.
[SCSI] qla2xxx: Add an "is reset active" helper.
[SCSI] qla2xxx: Add check for null fcport references in qla2xxx_queuecommand.
[SCSI] qla2xxx: Propagate up abort failures.
[SCSI] isci: Fix NULL ptr dereference when no firmware is being loaded
[SCSI] ipr: fix eeh recovery for 64-bit adapters
[SCSI] mpt2sas: Fix mismatch in mpt2sas_base_hard_reset_handler() mutex lock-unlock
|
|
This patch fixes an unbalanced refcount issue.
Elevating the lock for both kref_put and also for controller node deletion.
Previously, controller deletion was protected but the not the kref_put. This
was causing the other thread to pick up the controller structure which was
already kref'd zero.
This was causing the following WARN_ON and also sometimes panic.
WARNING: at lib/kref.c:43 kref_get+0x2d/0x30() (Not tainted)
Hardware name: IBM System x3655 -[7985AC1]-
Modules linked in: fuse scsi_dh_rdac autofs4 nfs lockd fscache nfs_acl
auth_rpcgss sunrpc 8021q garp stp llc ipv6 ib_srp(U) scsi_transport_srp
scsi_tgt ib_cm(U) ib_sa(U) ib_uverbs(U) ib_umad(U) mlx4_ib(U) mlx4_core(U)
ib_mthca(U) ib_mad(U) ib_core(U) dm_mirror dm_region_hash dm_log dm_round_robin
dm_multipath uinput bnx2 ses enclosure sg ibmpex ibmaem ipmi_msghandler
serio_raw k8temp hwmon amd64_edac_mod edac_core edac_mce_amd shpchp i2c_piix4
ext4 mbcache jbd2 sr_mod cdrom sd_mod crc_t10dif sata_svw pata_acpi ata_generic
pata_serverworks aacraid radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core
dm_mod [last unloaded: freq_table]
Pid: 13735, comm: srp_daemon Not tainted 2.6.32-71.el6.x86_64 #1
Call Trace:
[<ffffffff8106b857>] warn_slowpath_common+0x87/0xc0
[<ffffffff8106b8aa>] warn_slowpath_null+0x1a/0x20
[<ffffffff8125c39d>] kref_get+0x2d/0x30
[<ffffffffa01b4029>] rdac_bus_attach+0x459/0x580 [scsi_dh_rdac]
[<ffffffff8135232a>] scsi_dh_handler_attach+0x2a/0x80
[<ffffffff81352c7b>] scsi_dh_notifier+0x9b/0xa0
[<ffffffff814cd7a5>] notifier_call_chain+0x55/0x80
[<ffffffff8109711a>] __blocking_notifier_call_chain+0x5a/0x80
[<ffffffff81097156>] blocking_notifier_call_chain+0x16/0x20
[<ffffffff8132bec5>] device_add+0x515/0x640
[<ffffffff813329e4>] ? attribute_container_device_trigger+0xc4/0xe0
[<ffffffff8134f659>] scsi_sysfs_add_sdev+0x89/0x2c0
[<ffffffff8134d096>] scsi_probe_and_add_lun+0xea6/0xed0
[<ffffffff8134beb2>] ? scsi_alloc_target+0x292/0x2d0
[<ffffffff8134d1e1>] __scsi_scan_target+0x121/0x750
[<ffffffff811df806>] ? sysfs_create_file+0x26/0x30
[<ffffffff8132b759>] ? device_create_file+0x19/0x20
[<ffffffff81332838>] ? attribute_container_add_attrs+0x78/0x90
[<ffffffff814b008c>] ? klist_next+0x4c/0xf0
[<ffffffff81332e30>] ? transport_configure+0x0/0x20
[<ffffffff813329e4>] ? attribute_container_device_trigger+0xc4/0xe0
[<ffffffff8134df40>] scsi_scan_target+0xd0/0xe0
[<ffffffffa02f053a>] srp_create_target+0x75a/0x890 [ib_srp]
[<ffffffff8132a130>] dev_attr_store+0x20/0x30
[<ffffffff811df145>] sysfs_write_file+0xe5/0x170
[<ffffffff8116c818>] vfs_write+0xb8/0x1a0
[<ffffffff810d40a2>] ? audit_syscall_entry+0x272/0x2a0
[<ffffffff8116d251>] sys_write+0x51/0x90
[<ffffffff81013172>] system_call_fastpath+0x16/0x1b
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This provides unified readq()/writeq() helper functions for 32-bit
drivers.
For some cases, readq/writeq without atomicity is harmful, and order of
io access has to be specified explicitly. So in this patch, new two
header files which contain non-atomic readq/writeq are added.
- <asm-generic/io-64-nonatomic-lo-hi.h> provides non-atomic readq/
writeq with the order of lower address -> higher address
- <asm-generic/io-64-nonatomic-hi-lo.h> provides non-atomic readq/
writeq with reversed order
This allows us to remove some readq()s that were added drivers when the
default non-atomic ones were removed in commit dbee8a0affd5 ("x86:
remove 32-bit versions of readq()/writeq()")
The drivers which need readq/writeq but can do with the non-atomic ones
must add the line:
#include <asm-generic/io-64-nonatomic-lo-hi.h> /* or hi-lo.h */
But this will be nop in 64-bit environments, and no other #ifdefs are
required. So I believe that this patch can solve the problem of
1. driver-specific readq/writeq
2. atomicity and order of io access
This patch is tested with building allyesconfig and allmodconfig as
ARCH=x86 and ARCH=i386 on top of tip/master.
Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: James Bottomley <James.Bottomley@parallels.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hitoshi Mitake <h.mitake@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch (as1520) fixes a bug in the SCSI layer's power management
implementation.
LUN scanning can be carried out asynchronously in do_scan_async(), and
sd uses an asynchronous thread for the time-consuming parts of disk
probing in sd_probe_async(). Currently nothing coordinates these
async threads with system sleep transitions; they can and do attempt
to continue scanning/probing SCSI devices even after the host adapter
has been suspended. As one might expect, the outcome is not ideal.
This is what the "prepare" stage of system suspend was created for.
After the prepare callback has been called for a host, target, or
device, drivers are not allowed to register any children underneath
them. Currently the SCSI prepare callback is not implemented; this
patch rectifies that omission.
For SCSI hosts, the prepare routine calls scsi_complete_async_scans()
to wait until async scanning is finished. It might be slightly more
efficient to wait only until the host in question has been scanned,
but there's currently no way to do that. Besides, during a sleep
transition we will ultimately have to wait until all the host scanning
has finished anyway.
For SCSI devices, the prepare routine calls async_synchronize_full()
to wait until sd probing is finished. The routine does nothing for
SCSI targets, because asynchronous target scanning is done only as
part of host scanning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In do_scan_async(), calling scsi_autopm_put_host(shost) may reference
freed shost, and cause Posison overwitten warning.
Yes, this case can happen, for example, an USB is disconnected just
when do_scan_async() thread starts to run, then scsi_host_put() called
in scsi_finish_async_scan() will lead to shost be freed(because the
refcount of shost->shost_gendev decreases to 1 after USB disconnects),
at this point, if references shost again, system will show following
warning msg.
To make scsi_autopm_put_host(shost) always reference a valid shost,
put it just before scsi_host_put() in function
scsi_finish_async_scan().
[ 299.281565] =============================================================================
[ 299.281634] BUG kmalloc-4096 (Tainted: G I ): Poison overwritten
[ 299.281682] -----------------------------------------------------------------------------
[ 299.281684]
[ 299.281752] INFO: 0xffff880056c305d0-0xffff880056c305d0. First byte
0x6a instead of 0x6b
[ 299.281816] INFO: Allocated in scsi_host_alloc+0x4a/0x490 age=1688
cpu=1 pid=2004
[ 299.281870] __slab_alloc+0x617/0x6c1
[ 299.281901] __kmalloc+0x28c/0x2e0
[ 299.281931] scsi_host_alloc+0x4a/0x490
[ 299.281966] usb_stor_probe1+0x5b/0xc40 [usb_storage]
[ 299.282010] storage_probe+0xa4/0xe0 [usb_storage]
[ 299.282062] usb_probe_interface+0x172/0x330 [usbcore]
[ 299.282105] driver_probe_device+0x257/0x3b0
[ 299.282138] __driver_attach+0x103/0x110
[ 299.282171] bus_for_each_dev+0x8e/0xe0
[ 299.282201] driver_attach+0x26/0x30
[ 299.282230] bus_add_driver+0x1c4/0x430
[ 299.282260] driver_register+0xb6/0x230
[ 299.282298] usb_register_driver+0xe5/0x270 [usbcore]
[ 299.282337] 0xffffffffa04ab03d
[ 299.282364] do_one_initcall+0x47/0x230
[ 299.282396] sys_init_module+0xa0f/0x1fe0
[ 299.282429] INFO: Freed in scsi_host_dev_release+0x18a/0x1d0 age=85
cpu=0 pid=2008
[ 299.282482] __slab_free+0x3c/0x2a1
[ 299.282510] kfree+0x296/0x310
[ 299.282536] scsi_host_dev_release+0x18a/0x1d0
[ 299.282574] device_release+0x74/0x100
[ 299.282606] kobject_release+0xc7/0x2a0
[ 299.282637] kobject_put+0x54/0xa0
[ 299.282668] put_device+0x27/0x40
[ 299.282694] scsi_host_put+0x1d/0x30
[ 299.282723] do_scan_async+0x1fc/0x2b0
[ 299.282753] kthread+0xdf/0xf0
[ 299.282782] kernel_thread_helper+0x4/0x10
[ 299.282817] INFO: Slab 0xffffea00015b0c00 objects=7 used=7 fp=0x
(null) flags=0x100000000004080
[ 299.282882] INFO: Object 0xffff880056c30000 @offset=0 fp=0x (null)
[ 299.282884]
...
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Cc: stable@kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
ISP82xx.
With IOs running and PegHalt testing the system reboots when memory reset is
performed during device initialization.
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
failures during next reset cycle.
Complete the mailbox command timed out before initiating another abort cycle
to recover so that mailbox commands issued during next reset cycle don't fail
due to pending mailbox access timeout.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Remove the check for a NULL fcport so that the host reset will run
unconditionally to unwedge any commands before the device is offlined and to
prevent a quick runthrough of the SCSI error handling.
Signed-off-by: Michael Christie <mchristi@redhat.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
ISP2200 adapters only have 24 mailbox registers so read only that many.
Reported-by: Olatunji Ruwase <oor@cs.cmu.edu>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
processing.
This can cause instability in mailbox command state machine handling.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Not clearing the options flags in mbx1 could lead the firmware
into interpreting old data in mbx1 through mbx8. This could
lead to inadvertent DMA read/write operations to stale memory.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Many locations within the driver would use an inconsistent set of
checks to determine ISP-reset state. Consolidate the checks into
this inline-helper.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
NULL orom ptr passed in for verification which caused page fault.
We will set a default version when we don't have orom struct.
Reported-by: Dan Melnic <dan@seamicro.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In some scenarios, an EEH error can take a long time to be detected, since the
driver issues an MMIO read only after a device reset command times out and we
try to reset the adapter. This patch adds some code in ipr_cancel_op() to read
a hardware register so we detect the error earlier in case the op is being
aborted because of a timeout caused by a frozen adapter slot.
Another problem in such scenarios is that in __ipr_eh_host_reset() we change the
dump state flag from WAIT_FOR_DUMP to GET_DUMP, and the flag is later changed
from GET_DUMP to READ_DUMP in ipr_reset_restore_cfg_space(). However, if when
__ipr_eh_host_reset() is called by the SCSI error handling the function
ipr_reset_restore_cfg_space() has already been called by the PCI EEH code, we
end up with the flag in an inconsistent state. This patch also prevents this
problem.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
lock-unlock
If ioc->pci_error_recovery is set, goto out in mpt2sas_base_hard_reset_handler()
leads to unlock unheld ioc->reset_in_progress_mutex.
The patch fixes the issue by jumping afer mutex_unlock() call.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix assembler constraint to prevent overeager gcc optimisation
mac_esp: rename irq
mac_scsi: dont enable mac_scsi irq before requesting it
macfb: fix black and white modes
m68k/irq: Remove obsolete IRQ_FLG_* definitions
Fix up trivial conflict in arch/m68k/kernel/process_mm.c as per Geert.
|
|
Rename the "Mac ESP" irq as "ESP" to be consistent with all the other Mac
drivers and ESP drivers.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
Don't enable the SCSI irq when initialising the chip -- the irq has no
handler yet.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates on 20120118
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (49 commits)
[SCSI] libfc: remove redundant timer init for fcp
[SCSI] fcoe: Move fcoe_debug_logging from fcoe.h to fcoe.c
[SCSI] libfc: Declare local functions static
[SCSI] fcoe: fix regression on offload em matching function for initiator/target
[SCSI] qla4xxx: Update driver version to 5.02.00-k12
[SCSI] qla4xxx: Cleanup modinfo display
[SCSI] qla4xxx: Update license
[SCSI] qla4xxx: Clear the RISC interrupt bit during FW init
[SCSI] qla4xxx: Added error logging for firmware abort
[SCSI] qla4xxx: Disable generating pause frames in case of FW hung
[SCSI] qla4xxx: Temperature monitoring for ISP82XX core.
[SCSI] megaraid: fix sparse warnings
[SCSI] sg: convert to kstrtoul_from_user()
[SCSI] don't change sdev starvation list order without request dispatched
[SCSI] isci: fix, prevent port from getting stuck in the 'configuring' state
[SCSI] isci: fix start OOB
[SCSI] isci: fix io failures while wide port links are coming up
[SCSI] isci: allow more time for wide port targets
[SCSI] isci: enable wide port targets
[SCSI] isci: Fix IO fails when pull cable from phy in x4 wideport in MPC mode.
...
|
|
The fcp timer is already initialized when it gets allocated.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Move the definition of the global variable fcoe_debug_logging
from fcoe.h to fcoe.c. Avoid that sparse complains about missing
declarations for local functions or variables by declaring these
static.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Avoid that sparse complains about missing declarations for local
functions by declaring these static or by adding an #include directive.
Add the __percpu annotation where it is missing.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This is a regression introduced by commit
1ff9918b625457ce20d450d00f9ed0a12ba191b7 The else statement here is breaking
the initiator logic of allocating xid from the offloaded em xid pool for READ
I/O only to use DDP, as shown by the snippet of trace below, where the WRITE
is using xid 0x5 from the offloaded em xid pool:
Protocol VID Len S_ID D_ID OX_ID RX_ID Summary
..
*FCP 228 96 0b.08.01 -> 01.0f.00 0x0005 0xffff SCSI: Write(10) LUN: 0x00
FCP 228 76 01.0f.00 -> 0b.08.01 0x0005 0x828d XFER_RDY
...
The bug is in the else statement, for both initiator and target, the
new command will have FC frame header bit 23 (FC_FC_EX_CTX) cleared as it was
originated from the initiator. Also, this is assuming the frame header is
already filled up, which is only true for target since for initiator, this is a
new frame and oem_match gets called when em tries get xid for this i/o before
it is filled up and sent out.
The fix is to check if there is a fc_fcp_pkt associated w/ this frame from
fr_fsp(fp), since fr_fsp(fp) is NULL for tcm_fc target and non-I/O frame in
initiator. This should also return true for target only if it is an
FC_RCTL_DD_UNSOL_CMD and rx_id is not allocated.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Beautify modinfo display. Display correct info for ql4xextended_error_logging
[jejb: fixup checkpatch warning]
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch fix kernel panic during kdump.
Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Added debug print with error code in case of firmware error.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In case of FW hung ISP82xx generates continuous pause frames
which causes switch to disable port.
Added fix to disable generating pause frames in case of
FW hung
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
During watchdog, need to monitor temperature of ISP82XX core
and set device state to FAILED when temperature reaches
"Panic" level.
Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
There's a zero day mistake in the megaraid driver in that the code that
obtains the version number does a >> 8 on a char quantity. This >>8 causes a
sparse warning because it always produces zero. Al Viro suggested these
shifts should be >> 4 thus treating the firmware version as a BCD quantity.
However, in the interests of safety we've elected to replace the >> 8
quantities with an explicit zero, thus quieting the sparse warning while
preserving the same (albeit incorrect) version number as had previously been
seen.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Instead of open coding this function use kstrtoul_from_user() directly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The sdev is deleted from starved list and then try to dispatch from this
device. It's quite possible the sdev can't eventually dispatch a request,
then the sdev will be in starved list tail. This isn't fair.
There are two cases here:
1. unplug path. scsi_request_fn() calls to scsi_target_queue_ready(), then
the dev is removed from starved list, but quite possible host queue isn't
ready, the dev is moved to starved list without dispatching any request.
2. scsi_run_queue path. It deletes the dev from starved list first (both
global and local starved lists), then handles the dev. Then we could have
the same process like case 1.
This patch fixes the first case. Case 2 isn't fixed, because there is a
rare case scsi_run_queue finds host isn't busy but scsi_request_fn finds
host is busy (other CPU is faster to get host queue depth). Not deleting
the dev from starved list in scsi_run_queue will keep scsi_run_queue
looping (though this is very rare case, because host will become busy).
Fortunately fixing case 1 already gives big improvement for starvation in
my test. In a 12 disk JBOD setup, running file creation under EXT4, this
gives 12% more throughput.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When expander connected in x2 or x4 mode and with IO runnning, if
a cable from wideport is plugged out from the phy, IO's start failing
on all the targets.
Observed that when cable is pulled with IO running, cominit is
happening on all the links and IO's start dropping to 0 and eventually
the whole IO fails. Second observation, target is trying to open and
SCU is responding with "Open reject no destination".
A cause of the problem is when the port went from the "ready
configuring substate" back to "ready configuring substate" as a result
of phy being pulled off, scic suspended the port task scheduler
register. As a result no IO was allowed and in the "substate
configuring enter" routine the IO never goes back to 0. As a result
the port never comes out of "ready substate configuring".
The patch adds a mechanism of activate and deactivate phy when a port
link up, which fixes the problem.
Signed-off-by: Bartek Nowakowski <bartek.nowakowski@intel.com>
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Split scu_link_layer_start_oob function to reset and enable and
add flush after all steps.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When the first phy of a wide port comes up, don't report the port ready
yet, always wait for 250 miliseconds then config the port with all phys
added to the port. So that we can avoid reporting wide port device too
early to kernel, which caused the first IOs (report luns, inquirys)
failed due to not all the phys are configured into its port. Changes
also made that the phys in a wide port don't need to go through half
second wait time for consuming power.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When hot insert the wide port device through the mini-sas port,
the first IOs (Report Luns or Inquiry) may fail due to the device
trying to open to a SCU phy that is still in suspended state. This
IO failure causes the wide port device stuck in UPDATING_PORT_WIDTH
state.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Arrange for task_contexts prepared for the wide targets to account for
all the attached phys in the port.
Signed-off-by: Bartek Nowakowski <bartek.nowakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Failure seen pulling a cable from a x4 port configured in manual port
configuration (MPC) mode (MPC mode is set by the the OEM paramaters
provided by the platform or isci_firmware.bin). While IO running to
devices behind and expander, plugging out the cable from phy is causing
IO failures and IO drops on disks and never recover.
It happens because during link up/down the phy were being taken out of
the port.
Fix: during link down the phy is kept in the same logical port.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Bump the version now that the driver has atapi support and the initial
round of hotplug fixes. The EXPERIMENTAL tag should have been removed a
while back. While we're here also kill the "select SCSI_SAS_HOST_SMP"
as the build error was separately fixed by commit d962480e "[SCSI]
libsas: fix try_test_sas_gpio_gp_bit() build error".
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
As the field was never set, isci_print_tmf() using 'isci_tmf->device'
sometimes causes a kernel crash if the dev_dbg() statement is enabled.
Remove the unused field both from isci_tmf struct definition and from
isci_print_tmf()
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Gen-3 operation is marginal, default to gen-2 for now.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
"No task timeout timer reduced from 20 to 2 This timer controls how
long the SCU hardware will hold open the TX side of the connection
before sending a DONE. The timer allows the hardware to attempt to
optimize the DONE/CLOSE behavior to allow for new COMMAND IU to be
posted. In practice closing the connection quicker is better."
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
v1.3 allows the attenuation of the attached cables to be specified to
the driver in terms of 'short', 'medium', and 'long' (see probe_roms.h).
These settings (per phy) are retrieved from the platform oem-parameters
(BIOS rom) or via a module parameter override.
Reviewed-by: Jiangbi Liu <jiangbi.liu@intel.com>
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
v1.1 allows finer grained tuning of the SSC (spread-spectrum-clocking)
settings for SAS and SATA. See notes in probe_roms.h
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
C1 silicon requires updates to the phy tuning recipe and also support
for user provided cable selects (per-phy) for short, medium, and long
cables. Default to 'short' awaiting support for selecting the cable via
oem parameters.
Reviewed-by: Jiangbi Liu <jiangbi.liu@intel.com>
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
