| Age | Commit message (Collapse) | Author |
|---|
|
Implement ZBC support functions to setup zoned disks, both
host-managed and host-aware models. Only zoned disks that satisfy
the following conditions are supported:
1) All zones are the same size, with the exception of an eventual
last smaller runt zone.
2) For host-managed disks, reads are unrestricted (reads are not
failed due to zone or write pointer alignement constraints).
Zoned disks that do not satisfy these 2 conditions are setup with
a capacity of 0 to prevent their use.
The function sd_zbc_read_zones, called from sd_revalidate_disk,
checks that the device satisfies the above two constraints. This
function may also change the disk capacity previously set by
sd_read_capacity for devices reporting only the capacity of
conventional zones at the beginning of the LBA range (i.e. devices
reporting rc_basis set to 0).
The capacity message output was moved out of sd_read_capacity into
a new function sd_print_capacity to include this eventual capacity
change by sd_zbc_read_zones. This new function also includes a call
to sd_zbc_print_zones to display the number of zones and zone size
of the device.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[Damien: * Removed zone cache support
* Removed mapping of discard to reset write pointer command
* Modified sd_zbc_read_zones to include checks that the
device satisfies the kernel constraints
* Implemeted REPORT ZONES setup and post-processing based
on code from Shaun Tancheff <shaun.tancheff@seagate.com>
* Removed confusing use of 512B sector units in functions
interface]
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
These should go together with the rest of the T10 protection information
defintions.
[mkp: s/T10_DIF/T10_PI/]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
And remove the declaration of the latter in sd.h as scsi_debug was the
only user.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For historic reasons, io_opt is in bytes and max_sectors in block layer
sectors. This interface inconsistency is error prone and should be
fixed. But for 4.4--4.7 let's make the unit difference explicit via a
wrapper function.
Fixes: d0eb20a863ba ("sd: Optimal I/O size is in bytes, not sectors")
Cc: stable@vger.kernel.org # 4.4+
Reported-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Andrew Patterson <andrew.patterson@hpe.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During revalidate we check whether device capacity has changed before we
decide whether to output disk information or not.
The check for old capacity failed to take into account that we scaled
sdkp->capacity based on the reported logical block size. And therefore
the capacity test would always fail for devices with sectors bigger than
512 bytes and we would print several copies of the same discovery
information.
Avoid scaling sdkp->capacity and instead adjust the value on the fly
when setting the block device capacity and generating fake C/H/S
geometry.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <stable@vger.kernel.org>
Reported-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 4f258a46346c ("sd: Fix maximum I/O size for BLOCK_PC requests")
had the unfortunate side-effect of removing an implicit clamp to
BLK_DEF_MAX_SECTORS for REQ_TYPE_FS requests in the block layer
code. This caused problems for some SMR drives.
Debugging this issue revealed a few problems with the existing
infrastructure since the block layer didn't know how to deal with
device-imposed limits, only limits set by the I/O controller.
- Introduce a new queue limit, max_dev_sectors, which is used by the
ULD to signal the maximum sectors for a REQ_TYPE_FS request.
- Ensure that max_dev_sectors is correctly stacked and taken into
account when overriding max_sectors through sysfs.
- Rework sd_read_block_limits() so it saves the max_xfer and opt_xfer
values for later processing.
- In sd_revalidate() set the queue's max_dev_sectors based on the
MAXIMUM TRANSFER LENGTH value in the Block Limits VPD. If this value
is not reported, fall back to a cap based on the CDB TRANSFER LENGTH
field size.
- In sd_revalidate(), use OPTIMAL TRANSFER LENGTH from the Block Limits
VPD--if reported and sane--to signal the preferred device transfer
size for FS requests. Otherwise use BLK_DEF_MAX_SECTORS.
- blk_limits_max_hw_sectors() is no longer used and can be removed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93581
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: sweeneygj@gmx.com
Tested-by: Arzeets <anatol.pomozov@gmail.com>
Tested-by: David Eisner <david.eisner@oriel.oxon.org>
Tested-by: Mario Kicherer <dev@kicherer.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Like scmd_printk(), but the device name is passed in as
a string. Can be used by eg ULDs which do not have access
to the scsi_cmnd structure.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
A set of flags introduced in the block layer enable better control over
how protection information is handled. These flags are useful for both
error injection and data recovery purposes. Checking can be enabled and
disabled for controller and disk, and the guard tag format is now a
per-I/O property.
Update sd_protect_op to communicate the relevant information to the
low-level device driver via a set of flags in scsi_cmnd.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Until now the per-command transfer length has exclusively been gated by
the max_sectors parameter in the scsi_host template. Given that the size
of this parameter has been bumped to an unsigned int we have to be
careful not to exceed the target device's capabilities.
If the if the device specifies a Maximum Transfer Length in the Block
Limits VPD we'll use that value. Otherwise we'll use 0xffffffff for
devices that have use_16_for_rw set and 0xffff for the rest. We then
combine the chosen disk limit with max_sectors in the host template. The
smaller of the two will be used to set the max_hw_sectors queue limit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Messages about discovered disk properties are only printed once unless
they are found to have changed. Errors encountered during mode sense,
however, are printed every time we revalidate.
Quiesce mode sense errors so they are only printed during the first
scan.
[jejb: checkpatch fixes]
Bugzilla: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=733565
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Rather than having a separate constant for specifying the timeout on FLUSH
operations, use the basic I/O timeout value that is already configurable
on a per target basis to derive the FLUSH timeout. Looking at the current
definitions of these timeout values, the FLUSH operation is supposed to have
a value that is twice the normal timeout value. This patch preserves this
relationship while leveraging the flexibility of specifying the I/O timeout.
Based on a prior patch by KY Srinivasan <kys@microsoft.com>
Reviewed-by: KY Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
SATA drives located behind a SAS controller would incorrectly receive
WRITE SAME commands. Tweak the heuristics so that:
- If REPORT SUPPORTED OPERATION CODES is provided we will use that to
choose between WRITE SAME(16), WRITE SAME(10) and disabled. This also
fixes an issue with the old code which would issue WRITE SAME(10)
despite the command not being whitelisted in REPORT SUPPORTED
OPERATION CODES.
- If REPORT SUPPORTED OPERATION CODES is not provided we will fall back
to WRITE SAME(10) unless the device has an ATA Information VPD page.
The assumption is that a SATL which is smart enough to implement
WRITE SAME would also provide REPORT SUPPORTED OPERATION CODES.
To facilitate the new heuristics scsi_report_opcode() has been modified
to so we can distinguish between "operation not supported" and "RSOC not
supported".
Reported-by: H. Peter Anvin <hpa@zytor.com>
Tested-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Some arrays synchronize their full non volatile cache when the sd driver sends
a SYNCHRONIZE CACHE command. Unfortunately, they can have Terrabytes of this
and we send a SYNCHRONIZE CACHE for every barrier if an array reports it has a
writeback cache. This leads to massive slowdowns on journalled filesystems.
The fix is to allow userspace to turn off the writeback cache setting as a
temporary measure (i.e. without doing the MODE SELECT to write it back to the
device), so even though the device reported it has a writeback cache, the
user, knowing that the cache is non volatile and all they care about is
filesystem correctness, can turn that bit off in the kernel and avoid the
performance ruinous (and safety irrelevant) SYNCHRONIZE CACHE commands.
The way you do this is add a 'temporary' prefix when performing the usual
cache setting operations, so
echo temporary write through > /sys/class/scsi_disk/<disk>/cache_type
Reported-by: Ric Wheeler <rwheeler@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Implement support for WRITE SAME(10) and WRITE SAME(16) in the SCSI disk
driver.
- We set the default maximum to 0xFFFF because there are several
devices out there that only support two-byte block counts even with
WRITE SAME(16). We only enable transfers bigger than 0xFFFF if the
device explicitly reports MAXIMUM WRITE SAME LENGTH in the BLOCK
LIMITS VPD.
- max_write_same_blocks can be overriden per-device basis in sysfs.
- The UNMAP discovery heuristics remain unchanged but the discard
limits are tweaked to match the "real" WRITE SAME commands.
- In the error handling logic we now distinguish between WRITE SAME
with and without UNMAP set.
The discovery process heuristics are:
- If the device reports a SCSI level of SPC-3 or greater we'll issue
READ SUPPORTED OPERATION CODES to find out whether WRITE SAME(16) is
supported. If that's the case we will use it.
- If the device supports the block limits VPD and reports a MAXIMUM
WRITE SAME LENGTH bigger than 0xFFFF we will use WRITE SAME(16).
- Otherwise we will use WRITE SAME(10) unless the target LBA is beyond
0xFFFFFFFF or the block count exceeds 0xFFFF.
- no_write_same is set for ATA, FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
It does not make sense to translate ref tags with unexpected values.
Instead we simply ignore them and let the upper layers catch the
problem. Ref tags that contain the expected value are still remapped.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
We have experienced several devices which fail in a fashion we do not
currently handle gracefully in SCSI. After a failure these devices will
respond to the SCSI primary command set (INQUIRY, TEST UNIT READY, etc.)
but any command accessing the storage medium will time out.
The following patch adds an callback that can be used by upper level
drivers to inspect the results of an error handling command. This in
turn has been used to implement additional checking in the SCSI disk
driver.
If a medium access command fails twice but TEST UNIT READY succeeds both
times in the subsequent error handling we will offline the device. The
maximum number of failed commands required to take a device offline can
be tweaked in sysfs.
Also add a new error flag to scsi_debug which allows this scenario to be
easily reproduced.
[jejb: fix up integer parsing to use kstrtouint]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
There is no reason to limit the SCSI disk namespace to sdXXX.
Add new error messages to sd_probe() in the unlikely event that either
ida_get_new() or sd_format_disk_name() fail.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
SBC3r26 contains many changes to the Logical Block Provisioning
interfaces (formerly known as Thin Provisioning ditto). This patch
implements support for both the old and new schemes using the same
heuristic as before (whether the LBP VPD page is present).
The new code also allows the provisioning mode (i.e. choice of command)
to be overridden on a per-device basis via sysfs. Two additional modes
are supported in this version:
- WRITE SAME(10) with the UNMAP bit set
- WRITE SAME(10) without the UNMAP bit set. This allows us to support
devices that predate the TP/LBP enhancements in SBC3 and which work
by way zero-detection
Switching between modes has been consolidated in a helper function that
also updates the block layer topology according to the limitations of
the chosen command.
I experimented with trying WRITE SAME(16) if UNMAP fails, WRITE SAME(10)
if WRITE SAME(16) fails, etc. but found several devices that got
cranky. So for now we'll disable discard if one of the commands
fail. The user still has the option of selecting a different mode in
sysfs.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Replace sd_media_change() with sd_check_events().
* Move media removed logic into set_media_not_present() and
media_not_present() and set sdev->changed iff an existing media is
removed or the device indicates UNIT_ATTENTION.
* Make sd_check_events() sets sdev->changed if previously missing
media becomes present.
* Event is reported only if sdev->changed is set.
This makes media presence event reported if scsi_disk->media_present
actually changed or the device indicated UNIT_ATTENTION. For backward
compatibility, SDEV_EVT_MEDIA_CHANGE is generated each time
sd_check_events() detects media change event.
[jejb: fix boot failure]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The hw_sector_size variable could overflow if a device reported huge
physical blocks. Switch to the more accurate physical_block_size
terminology and make sure we use an unsigned int to match the range
permitted by READ CAPACITY(16).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Add support for the Thin Provisioning VPD page and use the TPU and TPWS
bits to switch between UNMAP and WRITE SAME(16) for discards. If no TP
VPD page is present we fall back to old scheme where the max descriptor
count combined with the max lba count are used trigger UNMAP.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
We have been seeing the flush request timeout with a wide
range of hardware from tgt+iser to FC targets from a major vendor.
After discussions about if the value should be configurable and
what the best value should be, this patch just increases the flush/sync
cache timeout to 1 minute. 2 minutes was determined to be too long, and
making it configurable was troublesome for users.
This patch was made over Linus's tree. It is not made over scsi-misc
or scsi-rc-fixes, because Linus's had block layer changes that my
patch was built over.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Every user of the BKL in the sd driver is the
result of the pushdown from the block layer
into the open/close/ioctl functions.
The only place that used to rely on the BKL is
the sdkp->openers variable, which gets converted
into an atomic_t.
Nothing else seems to rely on the BKL, since the
functions do not touch global data without holding
another lock, and the open/close functions are
still protected from concurrent execution using
the bdev->bd_mutex.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-scsi@vger.kernel.org
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Implement a function for handling discard requests that sends either
WRITE SAME(16) or UNMAP(10) depending on parameters indicated by the
device in the block limits VPD.
Extract unmap constraints and report them to the block layer.
Based in part by a patch by Christoph Hellwig <hch@lst.de>.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Disks formatted with DIF Type 2 reject READ/WRITE 6/10/12/16 commands
when protection is enabled. Only the 32-byte variants are supported.
Implement support for issusing 32-byte READ/WRITE and enable Type 2
drives in the protection type detection logic.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
So far we have only issued DIF commands if CONFIG_BLK_DEV_INTEGRITY is
enabled. However, communication between initiator and target should be
independent of protection information DMA. There are DIF-only host
adapters coming out that will be able to take advantage of this.
Move the relevant DIF bits to sd.c.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Extract physical block size and lowest aligned LBA from READ
CAPACITY(16) response and adjust queue parameters.
Report physical block size and alignment when applicable.
[jejb: fix up trailing whitespace]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
sd_revalidate ends up being called several times during device setup.
With this patch we print everything during the first scan. Subsequent
invocations will only print a message if the parameter in question has
actually changed (LUN capacity has increased, etc.).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The old detection code couldn't handle all possible combinations of
DIX and DIF. This version does, giving priority to DIX if the
controller is capable.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This re-introduces commit 2b142900784c6e38c8d39fa57d5f95ef08e735d8,
which was reverted due to the regression it caused by commit
fca082c9f1e11ec07efa8d2f9f13688521253f36.
That regression was not root-caused by the original commit, it was just
uncovered by it, and the real fix was done by Alan Stern in commit
580da34847488b404218d1d7f53b156f245f5555 ("Fix USB storage hang on
command abort").
We can thus re-introduce the change that was confirmed by Alan Jenkins
to be still required by his odd card reader.
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 2b142900784c6e38c8d39fa57d5f95ef08e735d8, since it
seems to break some other USB storage devices (at least a JMicron USB to
ATA bridge). As such, while it apparently fixes some cardreaders, it
would need to be made conditional on the exact reader it fixes in order
to avoid causing regressions.
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The last_sector_bug flag was added to work around a bug in certain usb
cardreaders, where they would crash if a multiple sector read included the
last sector. The original implementation avoids this by e.g. splitting an 8
sector read which includes the last sector into a 7 sector read, and a single
sector read for the last sector. The flag is enabled for all USB devices.
This revealed a second bug in other usb cardreaders, which crash when they
get a multiple sector read which stops 1 sector short of the last sector.
Affected hardware includes the Kingston "MobileLite" external USB cardreader
and the internal USB cardreader on the Asus EeePC.
Extend the last_sector_bug workaround to ensure that any access which touches
the last 8 hardware sectors of the device is a single sector long. Requests
are shrunk as necessary to meet this constraint.
This gives us a safety margin against potential unknown or future bugs
affecting multi-sector access to the end of the device. The two known bugs
only affect the last 2 sectors. However, they suggest that these devices
are prone to fencepost errors and that multi-sector access to the end of the
device is not well tested. Popular OS's use multi-sector accesses, but they
rarely read the last few sectors. Linux (with udev & vol_id) automatically
reads sectors from the end of the device on insertion. It is assumed that
single sector accesses are more thoroughly tested during development.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Support for controllers and disks that implement DIF protection
information:
- During command preparation the RDPROTECT/WRPROTECT must be set
correctly if the target has DIF enabled.
- READ(6) and WRITE(6) are not supported when DIF is on.
- The controller must be told how to handle the I/O via the
protection operation field in scsi_cmnd.
- Refactor the I/O completion code that extracts failed LBA from the
returned sense data and handle DIF failures correctly.
- sd_dif.c implements the functions required to prepare and complete
requests with protection information attached.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If a disk is formatted with protection information (Inquiry bit
PROTECT=1) it is required to support Read Capacity(16). Force use of
the 16-bit command in this case and extract the P_TYPE field which
indicates whether the disk is formatted using DIF Type 1, 2 or 3.
The ATO (App Tag Own) bit in the Control Mode Page indicates whether
the storage device or the initiator own the contents of the
DIF application tag.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Christoph objected to having sd.h in include/scsi since it is internal
to the sd driver. Move it to drivers/scsi/sd.h.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
