| Age | Commit message (Collapse) | Author |
|---|
|
Currently it's impossible to find out if the host supports
wide SCSI unless you're committed to trawl through syslog.
And it's near impossible to find the actual HBA id, which
is settable for some SCSI HBAs (like aic7xxx).
So export them via sysfs.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Ankit Jain <jankit@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
There have been several bug reports which identified the Ultrium-3
tape as just hanging up on the bus during certain types of IU
transfer. The identified culpret is type 0x02 (MULTIPLE COMMAND)
transfers. The only way to prevent this tape wedging is to prevent it
from using IU transfers at all. So this patch uses the exported
blacklist matching technology to recognise the drive and force it not
to use IU transfers.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Right at the moment, we carefully set up the spi_support_xx in the
device configuration routines, but then we never actually use the
results: we rely on the inquiry strings. If we're going to allow
overrides to the inquiry data, we have to rely on our own internal
settings.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch allows the Adaptec firmware to pass on its values for Packetize and
QAS. To do this, the settings max_iu and max_qas have been introduced into
the SPI transport class and populated from the adaptec NVram tables. Domain
validation in the SPI transport class will respect the max settings when
configuring to the highest possible speed for testing.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
[jejb: fix rejections]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
scsi_execute() and scsi_execute_req() discard the residual length
information. Some callers need it. This adds residual argument
(optional) to scsi_execute and scsi_execute_req.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Multipath is best at handling transport errors. If it gets a device
error then there is not much the multipath layer can do. It will just
access the same device but from a different path.
This patch breaks up failfast into device, transport and driver errors.
The multipath layers (md and dm mutlipath) only ask the lower levels to
fast fail transport errors. The user of failfast, read ahead, will ask
to fast fail on all errors.
Note that blk_noretry_request will return true if any failfast bit
is set. This allows drivers that do not support the multipath failfast
bits to continue to fail on any failfast error like before. Drivers
like scsi that are able to fail fast specific errors can check
for the specific fail fast type. In the next patch I will convert
scsi.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The class_device->device conversion is causing an oops in revalidate
because it's assuming that the device_for_each_child iterator will only
return struct scsi_device children. The conversion made all former
class_devices children of the device as well, so this assumption is
broken. Fix it.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
scsi_transport_spi.c needs to #include <linux/sysfs.h>:
next-20080423/drivers/scsi/scsi_transport_spi.c:1467: error: implicit declaration of function 'sysfs_update_group'
make[3]: *** [drivers/scsi/scsi_transport_spi.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
We now take advantage of the mode_t return of is_valid, and also
update the attributes when the target is configured.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This conversion makes full use of the is_visible() callback on attribute
groups. Now, each device appears only with its capability flags in the
transport class directory. Previously each device appeared with the
capability of the host, so this is a functionality improvement.
Converting to attribute groups allows us to sweep away most of the home
grown #defines that were effectively doing the same thing.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
width setting
Domain Validation in the SPI transport class is failing on boxes with
damaged cables (and failing to the extent that the box hangs). The
problem is that the first test it does is a cable integrity test for
wide transfers and if this fails, it turns the wide bit off. The
problem is that the next set of tests it does turns wide back on
again, with the result that it runs through the entirety of DV with a
known bad setting and then hangs the system.
The attached patch fixes the problem by physically nailing the wide
setting to what it deduces it should be for the whole of Domain
Validation.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The code does this:
unsigned char sense[SCSI_SENSE_BUFFERSIZE];
...
scsi_normalize_sense(sense, sizeof(*sense), sshdr)
however the sizeof will return 1 not 96 which means the sense data will
have no valid ASC/ASCQ values. Fix by putting the correct sense size.
The only affected case for this would have been the DV buffer sanity
check failure, which is fortunately quite rare.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Fix up for make allyesconfig.
Signed-Off-By: David Howells <dhowells@redhat.com>
|
|
Key more of the domain validation settings off the inquiry data from
the disk (in particular, don't try IU or DT unless the disk claims to
support them.
Also add a new dv_in_progress flag to prevent recursive DV.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This is really just a belt and braces test. The standards require
disks to respond DT not capable on a non-LVD bus ... however, not all
disks follow the standards ...
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of the macro.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The check for a one byte message should be msg[0] == 0x55 not msg == 0x55
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Add several missing messages from SPI3, SPI4 and SPI5:
- Terminate Process
- Continue Task
- Target Transfer Disable
- Clear ACA
- LUN Reset
- ACA
- QAS Request
Rename some older commands to their SPI5 names:
- Command Complete -> Task Complete
- Abort -> Abort Task Set
- Bus device Reset -> Target Reset
- Clear Queue -> Clear Task Set
Change spi_print_msg() to always consume one byte, even if we don't
recognise it. That allows drivers to call it in a loop to print all
messages.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Fix a bug where we would consume one byte too many in the message
printing code.
Add support for 256-byte long messages.
Add support for the Modify Bidirectional Data Pointer message.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Almost all the output from spi_print_msg() has a trailing space.
This patch fixes up the three cases that don't.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Introduce new helpers:
- spi_populate_width_msg()
- spi_populate_sync_msg()
- spi_populate_ppr_msg()
and use them in drivers which already enable the SPI transport.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
show_spi_transport_period_helper() doesn't need the class_device parameter
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Change the core SCSI code to use kzalloc rather than kmalloc+memset
where possible.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Convert the SCSI transport class code to use a mutex rather than a
semaphore.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Introduce a new helper, print_nego() to handle SDTR/WDTR/PPR.
Split out the guts of show_spi_transport_period_helper() into period_to_str()
and use it in print_nego to get the period factor conversion right.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Replace the custom NO_*_MSGS definitions with uses of ARRAY_SIZE.
This fixes a bug in the definition of NO_EXTENDED_MSGS.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
A missing comma meant that "Ordered Queue Tag" and "Ignore Wide Residue"
were being concatenated together.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Rename scsi_print_msg to spi_print_msg and move its prototype from
scsi_dbg.h to scsi_transport_spi.h
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
scsi_print_msg() is an SPI-specific concept. This patch moves it from
constants.c to scsi_transport_spi.c and updates the Kconfig to link in
the SPI class for the drivers which use scsi_print_msg().
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
None of the other domain validation messages have a trailing full stop,
so I don't see why this one should.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Some SCSI devices apparently get very confused if we try to use the
echo buffer on a non-DT negotiated bus (this mirrors the problems of
using PPR on non-LVD for some devices). The fix is to be far more
conservative about when we use an echo buffer. With this patch, we'll
now see what parameters are negotiated by the read only test, and only
look for an echo buffer if DT is negotiated.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This should eliminate (at least in the mid layer) to make numeric
assumptions about any of the enumeration variables. As a side effect,
it will also make all the messages consistent and line us up nicely for
the error logging strategy (if it ever shows itself again).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This one's slightly more difficult. The transport class uses
REQ_FAILFAST, so another interface (scsi_execute) had to be invented to
take the extra flag. Also, the sense functions are shifted around to
allow spi_execute to place data directly into a struct scsi_sense_hdr.
With this change, there's probably a lot of unnecessary sense buffer
allocation going on which we can fix later.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
I recently tried to construct a totally generic transport class and
found there were certain features missing from the current abstract
transport class. Most notable is that you have to hang the data on the
class_device but most of the API is framed in terms of the generic
device, not the class_device.
These changes are two fold
- Provide the class_device to all of the setup and configure APIs
- Provide and extra API to take the device and the attribute class and
return the corresponding class_device
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This patch is necessary if we begin exposing underlying physical disks
(which can attach to the SPI transport class) of the hardware RAID
cards, since we don't want any SPI parameters binding to the RAID
devices.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This parameter is important only to people who take the time to tune the
margin control settings, otherwise it's completely irrelevant. However,
just in case anyone should want to do this, it's appropriate to include
the parameter.
I don't do anything with it in DV by design, so the parameter will come
up as off by default, so if anyone actually wants to play with the
margin control settings they'll have to enable it under the
spi_transport class first.
I also updated the transfer settings display to report all of the PPR
settings instead of only DT, IU and QAS
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
At the moment, the transport class blindly tries to set things like
QAS and IU, even if the drive won't support them. It's best not to
annoy the devices like this and instead only set what the drive says
is actually supported.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
There are several extra things that have to be considered when running
Domain Validation on a u320 target (notably how you fall back).
Hopefully this should help us when someone adds this transport class to
aic79xx.
I've tested this on the lsi1030, so I know it works correctly up to
u320.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
There's a basic need not to have parameters go under or over certain
values when doing domain validation. The basic ones are
max_offset, max_width and min_period
This patch makes the transport class take and enforce these three
limits. Currently they can be set by the user, although they could
obviously be read from the HBA's on-board NVRAM area during
slave_configure (if it has one).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The premise is that domain validation is likely to trigger errors which
it wants to know about, so the only time it should be retrying them is
when it gets a unit attention (likely as the result of a previous bus or
device reset). Ironically, the previous coding retried three times in
all cases except those of unit attention. The attached fixes this to do
the right thing.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
