summaryrefslogtreecommitdiff
path: root/drivers/scsi/mpt3sas
AgeCommit message (Collapse)Author
2020-07-07scsi: mpt3sas: Fix error returns in BRM_status_showJohannes Thumshirn
BRM_status_show() has several error branches, but none of them record the error in the error return. Also while at it remove the manual mutex_unlock() of the pci_access_mutex in case of an ongoing pci error recovery or host removal and jump to the cleanup label instead. Note: We can safely jump to out from here as io_unit_pg3 is initialized to NULL and if it hasn't been allocated, kfree() skips the NULL pointer. [mkp: compilation warning] Link: https://lore.kernel.org/r/20200701131454.5255-1-johannes.thumshirn@wdc.com Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com> Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-07-02scsi: mpt3sas: Fix unlock imbalanceDamien Le Moal
In BRM_status_show(), if the condition "!ioc->is_warpdrive" tested on entry to the function is true, a "goto out" is called. This results in unlocking ioc->pci_access_mutex without this mutex lock being taken. This generates the following splat: [ 1148.539883] mpt3sas_cm2: BRM_status_show: BRM attribute is only for warpdrive [ 1148.547184] [ 1148.548708] ===================================== [ 1148.553501] WARNING: bad unlock balance detected! [ 1148.558277] 5.8.0-rc3+ #827 Not tainted [ 1148.562183] ------------------------------------- [ 1148.566959] cat/5008 is trying to release lock (&ioc->pci_access_mutex) at: [ 1148.574035] [<ffffffffc070b7a3>] BRM_status_show+0xd3/0x100 [mpt3sas] [ 1148.580574] but there are no more locks to release! [ 1148.585524] [ 1148.585524] other info that might help us debug this: [ 1148.599624] 3 locks held by cat/5008: [ 1148.607085] #0: ffff92aea3e392c0 (&p->lock){+.+.}-{3:3}, at: seq_read+0x34/0x480 [ 1148.618509] #1: ffff922ef14c4888 (&of->mutex){+.+.}-{3:3}, at: kernfs_seq_start+0x2a/0xb0 [ 1148.630729] #2: ffff92aedb5d7310 (kn->active#224){.+.+}-{0:0}, at: kernfs_seq_start+0x32/0xb0 [ 1148.643347] [ 1148.643347] stack backtrace: [ 1148.655259] CPU: 73 PID: 5008 Comm: cat Not tainted 5.8.0-rc3+ #827 [ 1148.665309] Hardware name: HGST H4060-S/S2600STB, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019 [ 1148.678394] Call Trace: [ 1148.684750] dump_stack+0x78/0xa0 [ 1148.691802] lock_release.cold+0x45/0x4a [ 1148.699451] __mutex_unlock_slowpath+0x35/0x270 [ 1148.707675] BRM_status_show+0xd3/0x100 [mpt3sas] [ 1148.716092] dev_attr_show+0x19/0x40 [ 1148.723664] sysfs_kf_seq_show+0x87/0x100 [ 1148.731193] seq_read+0xbc/0x480 [ 1148.737882] vfs_read+0xa0/0x160 [ 1148.744514] ksys_read+0x58/0xd0 [ 1148.751129] do_syscall_64+0x4c/0xa0 [ 1148.757941] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 1148.766240] RIP: 0033:0x7f1230566542 [ 1148.772957] Code: Bad RIP value. [ 1148.779206] RSP: 002b:00007ffeac1bcac8 EFLAGS: 00000246 ORIG_RAX: 0000000000000000 [ 1148.790063] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007f1230566542 [ 1148.800284] RDX: 0000000000020000 RSI: 00007f1223460000 RDI: 0000000000000003 [ 1148.810474] RBP: 00007f1223460000 R08: 00007f122345f010 R09: 0000000000000000 [ 1148.820641] R10: 0000000000000022 R11: 0000000000000246 R12: 0000000000000000 [ 1148.830728] R13: 0000000000000003 R14: 0000000000020000 R15: 0000000000020000 Fix this by returning immediately instead of jumping to the out label. Link: https://lore.kernel.org/r/20200701085254.51740-1-damien.lemoal@wdc.com Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-06-13Merge tag 'kbuild-v5.8-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull more Kbuild updates from Masahiro Yamada: - fix build rules in binderfs sample - fix build errors when Kbuild recurses to the top Makefile - covert '---help---' in Kconfig to 'help' * tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: treewide: replace '---help---' in Kconfig files with 'help' kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables samples: binderfs: really compile this sample and fix build issues
2020-06-14treewide: replace '---help---' in Kconfig files with 'help'Masahiro Yamada
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over '---help---'"), the number of '---help---' has been gradually decreasing, but there are still more than 2400 instances. This commit finishes the conversion. While I touched the lines, I also fixed the indentation. There are a variety of indentation styles found. a) 4 spaces + '---help---' b) 7 spaces + '---help---' c) 8 spaces + '---help---' d) 1 space + 1 tab + '---help---' e) 1 tab + '---help---' (correct indentation) f) 1 tab + 1 space + '---help---' g) 1 tab + 2 spaces + '---help---' In order to convert all of them to 1 tab + 'help', I ran the following commend: $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/' Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2020-06-02scsi: mpt3sas: Fix memset() in non-RDPQ modeSuganath Prabu S
Fix memset() accessing out of range address when reply_queue count is less than RDPQ_MAX_INDEX_IN_ONE_CHUNK (i.e. 16) in non-RDPQ mode. In non-RDPQ mode, the driver allocates a single contiguous pool of size reply_queue's count * reqly_post_free_sz. But the driver is always memsetting this pool with size 16 * reqly_post_free_sz. If reply queue count is less than 16 (i.e. when MSI-X vectors enabled < 16), the driver is accessing out of range address and this results in 'BUG: unable to handle kernel paging request at fff0x...x' bug. Make driver use dma_pool_zalloc() API to allocate and zero the pool. Link: https://lore.kernel.org/r/20200528145617.27252-1-suganath-prabu.subramani@broadcom.com Fixes: 8012209eb26b ("scsi: mpt3sas: Handle RDPQ DMA allocation in same 4G region") Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-05-26scsi: mpt3sas: Fix reply queue count in non RDPQ modeSuganath Prabu S
For non RDPQ mode, the driver allocates a single contiguous block of memory pool for all reply descriptor post queues and passes down a single address in the ReplyDescriptorPostQueueAddress field of the IOC Init Request Message to the firmware. So reply_post queue will have only one entry which holds the address of this single contiguous block of memory pool. While allocating the reply descriptor post queue pool, driver should loop only once in non-RDPQ mode. But the driver is looping for ioc->reply_queue_count number of times even though reply_post queue's queue depth is only one in non-RDPQ mode. This leads to 'BUG: KASAN: use-after-free in base_alloc_rdpq_dma_pool'. The fix is to loop only once while allocating memory for the reply descriptor post queue in non-RDPQ mode Fixes: 8012209eb26b ("scsi: mpt3sas: Handle RDPQ DMA allocation in same 4G region") Link: https://lore.kernel.org/r/20200522103558.5710-1-suganath-prabu.subramani@broadcom.com Reported-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-05-11scsi: mpt3sas: Remove unused including <linux/version.h>Samuel Zou
Fix the following versioncheck warning: drivers/scsi/mpt3sas/mpt3sas_debugfs.c:16:1: unused including <linux/version.h> Link: https://lore.kernel.org/r/1588938573-57847-1-git-send-email-zou_wei@huawei.com Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Samuel Zou <zou_wei@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-05-11scsi: mpt3sas: Fix double free warningsSuganath Prabu S
Fix following warning from Smatch static analyser: drivers/scsi/mpt3sas/mpt3sas_base.c:5256 _base_allocate_memory_pools() warn: 'ioc->hpr_lookup' double freed drivers/scsi/mpt3sas/mpt3sas_base.c:5256 _base_allocate_memory_pools() warn: 'ioc->internal_lookup' double freed Link: https://lore.kernel.org/r/20200508110738.30732-1-suganath-prabu.subramani@broadcom.com Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-05-07scsi: mpt3sas: Disable DIF when prot_mask set to zeroSreekanth Reddy
By default DIF Type 1, DIF Type 2 & DIF Type 3 will be enabled. Also, users can enable either DIF Type 1 or DIF Type 2 or DIF Type 3 or in any combination using the prot_mask module parameter. However, when the user provides a prot_mask module parameter value of zero, then the driver is not disabling the DIF. Instead it enables all three types. Modify the driver to disable the DIF support if the user provides a prot_mask module parameter value of zero. Link: https://lore.kernel.org/r/1588065902-2726-1-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-05-07scsi: mpt3sas: Capture IOC data for debugging purposesSuganath Prabu
Information needed to debug driver problems and firmware faults is stored in the IOC’s MPT3SAS_ADAPTER data structure. Parameters such as IOCFacts, IOC flags (related to sge, MSI-X, error recovery etc.), performance mode type, TMs, internal commands reply status, etc. are present. For debugging purposes, it is therefore helpful to be able to capture this information so that the fault can be analyzed. Export the MPT3SAS_ADAPTER data structure in debugfs. The data is available in: /sys/kernel/debug/mpt3sas/scsi_hostX/ioc_dump Link: https://lore.kernel.org/r/1588056322-29227-1-git-send-email-suganath-prabu.subramani@broadcom.com Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-05-07scsi: mpt3sas: Use true, false for ioc->use_32bit_dmaJason Yan
Fix the following coccicheck warning: drivers/scsi/mpt3sas/mpt3sas_base.c:7202:1-19: WARNING: Assignment of 0/1 to bool variable Link: https://lore.kernel.org/r/20200430121738.15151-1-yanaijie@huawei.com Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-04-24scsi: mpt3sas: Remove NULL check before freeing functionJason Yan
Fix the following coccicheck warning: drivers/scsi/mpt3sas/mpt3sas_base.c:4906:3-19: WARNING: NULL check before some freeing functions is not needed. Link: https://lore.kernel.org/r/20200418095850.34883-1-yanaijie@huawei.com Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-04-24scsi: mpt3sas: Update mpt3sas version to 33.101.00.00Suganath Prabu
Update mpt3sas driver version from 33.100.00.00 to 33.101.00.00. Link: https://lore.kernel.org/r/1587626596-1044-6-git-send-email-suganath-prabu.subramani@broadcom.com Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-04-24scsi: mpt3sas: Handle RDPQ DMA allocation in same 4G regionSuganath Prabu
For INVADER_SERIES, each set of 8 reply queues (0 - 7, 8 - 15,..), and for VENTURA_SERIES, each set of 16 reply queues (0 - 15, 16 - 31,..) need to be within the same 4 GB boundary. Driver uses limitation of VENTURA_SERIES to manage INVADER_SERIES as well. The driver is allocating the DMA able memory for RDPQs accordingly. 1) At driver load, set DMA mask to 64 and allocate memory for RDPQs 2) Check if allocated resources for RDPQ are in the same 4GB range 3) If #2 is true, continue with 64 bit DMA and go to #6 4) If #2 is false, then free all the resources from #1 5) Set DMA mask to 32 and allocate RDPQs 6) Proceed with driver loading and other allocations Link: https://lore.kernel.org/r/1587626596-1044-5-git-send-email-suganath-prabu.subramani@broadcom.com Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-04-24scsi: mpt3sas: Separate out RDPQ allocation to new functionSuganath Prabu
For readability separate out RDPQ allocations to new function base_alloc_rdpq_dma_pool(). Link: https://lore.kernel.org/r/1587626596-1044-4-git-send-email-suganath-prabu.subramani@broadcom.com Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-04-24scsi: mpt3sas: Rename function name is_MSB_are_sameSuganath Prabu
Rename is_MSB_are_same() to mpt3sas_check_same_4gb_region() for better readability. Link: https://lore.kernel.org/r/1587626596-1044-3-git-send-email-suganath-prabu.subramani@broadcom.com Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-04-24scsi: mpt3sas: Don't change the DMA coherent mask after allocationsChristoph Hellwig
The DMA layer does not allow changing the DMA coherent mask after there are outstanding allocations. Link: https://lore.kernel.org/r/1587626596-1044-2-git-send-email-suganath-prabu.subramani@broadcom.com Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-04-22scsi: mpt3sas: use true,false for bool variablesJason Yan
Fix the following coccicheck warning: drivers/scsi/mpt3sas/mpt3sas_base.c:416:6-14: WARNING: Assignment of 0/1 to bool variable drivers/scsi/mpt3sas/mpt3sas_base.c:485:2-10: WARNING: Assignment of 0/1 to bool variable Link: https://lore.kernel.org/r/20200421034101.28273-1-yanaijie@huawei.com Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-03-31scsi: mpt3sas: Fix kernel panic observed on soft HBA unplugSreekanth Reddy
Generic protection fault type kernel panic is observed when user performs soft (ordered) HBA unplug operation while IOs are running on drives connected to HBA. When user performs ordered HBA removal operation, the kernel calls PCI device's .remove() call back function where driver is flushing out all the outstanding SCSI IO commands with DID_NO_CONNECT host byte and also unmaps sg buffers allocated for these IO commands. However, in the ordered HBA removal case (unlike of real HBA hot removal), HBA device is still alive and hence HBA hardware is performing the DMA operations to those buffers on the system memory which are already unmapped while flushing out the outstanding SCSI IO commands and this leads to kernel panic. Don't flush out the outstanding IOs from .remove() path in case of ordered removal since HBA will be still alive in this case and it can complete the outstanding IOs. Flush out the outstanding IOs only in case of 'physical HBA hot unplug' where there won't be any communication with the HBA. During shutdown also it is possible that HBA hardware can perform DMA operations on those outstanding IO buffers which are completed with DID_NO_CONNECT by the driver from .shutdown(). So same above fix is applied in shutdown path as well. It is safe to drop the outstanding commands when HBA is inaccessible such as when permanent PCI failure happens, when HBA is in non-operational state, or when someone does a real HBA hot unplug operation. Since driver knows that HBA is inaccessible during these cases, it is safe to drop the outstanding commands instead of waiting for SCSI error recovery to kick in and clear these outstanding commands. Link: https://lore.kernel.org/r/1585302763-23007-1-git-send-email-sreekanth.reddy@broadcom.com Fixes: c666d3be99c0 ("scsi: mpt3sas: wait for and flush running commands on shutdown/unload") Cc: stable@vger.kernel.org #v4.14.174+ Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-03-11scsi: Replace zero-length array with flexible-array memberGustavo A. R. Silva
The current codebase makes use of the zero-length array language extension to the C90 standard, but the preferred mechanism to declare variable-length types such as these ones is a flexible array member[1][2], introduced in C99: struct foo { int stuff; struct boo array[]; }; By making use of the mechanism above, we will get a compiler warning in case the flexible array does not occur last in the structure, which will help us prevent some kind of undefined behavior bugs from being inadvertently introduced[3] to the codebase from now on. Also, notice that, dynamic memory allocations won't be affected by this change: "Flexible array members have incomplete type, and so the sizeof operator may not be applied. As a quirk of the original implementation of zero-length arrays, sizeof evaluates to zero."[1] This issue was found with the help of Coccinelle. [1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html [2] https://github.com/KSPP/linux/issues/21 [3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour") Link: https://lore.kernel.org/r/20200224161406.GA21454@embeddedor Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Satish Kharat <satishkh@cisco.com> Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-10Merge tag 'block-ioctl-cleanup-5.6' into 5.6/scsi-queueMartin K. Petersen
Pull compat_ioctl cleanup from Arnd. Here's his description: This series concludes the work I did for linux-5.5 on the compat_ioctl() cleanup, killing off fs/compat_ioctl.c and block/compat_ioctl.c by moving everything into drivers. Overall this would be a reduction both in complexity and line count, but as I'm also adding documentation the overall number of lines increases in the end. My plan was originally to keep the SCSI and block parts separate. This did not work easily because of interdependencies: I cannot do the final SCSI cleanup in a good way without first addressing the CDROM ioctls, so this is one series that I hope could be merged through either the block or the scsi git trees, or possibly both if you can pull in the same branch. The series comes in these steps: 1. clean up the sg v3 interface as suggested by Linus. I have talked about this with Doug Gilbert as well, and he would rebase his sg v4 patches on top of "compat: scsi: sg: fix v3 compat read/write interface" 2. Actually moving handlers out of block/compat_ioctl.c and block/scsi_ioctl.c into drivers, mixed in with cleanup patches 3. Document how to do this right. I keep getting asked about this, and it helps to point to some documentation file. The branch is based on another one that fixes a couple of bugs found during the creation of this series. Changes since v3: https://lore.kernel.org/lkml/20200102145552.1853992-1-arnd@arndb.de/ - Move sr_compat_ioctl fixup to correct patch (Ben Hutchings) - Add Reviewed-by tags Changes since v2: https://lore.kernel.org/lkml/20191217221708.3730997-1-arnd@arndb.de/ - Rebase to v5.5-rc4, which contains the earlier bugfixes - Fix sr_block_compat_ioctl() error handling bug found by Ben Hutchings - Fix idecd_locked_compat_ioctl() compat_ptr() bug - Don't try to handle HDIO_DRIVE_TASKFILE in drivers/ide - More documentation improvements Changes since v1: https://lore.kernel.org/lkml/20191211204306.1207817-1-arnd@arndb.de/ - move out the bugfixes into a branch for itself - clean up scsi sg driver further as suggested by Christoph Hellwig - avoid some ifdefs by moving compat_ptr() out of asm/compat.h - split out the blkdev_compat_ptr_ioctl function; bug spotted by Ben Hutchings - Improve formatting of documentation Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-02scsi: mpt3sas: Update drive version to 33.100.00.00Sreekanth Reddy
Update mpt3sas driver version from 32.100.00.00 to 33.100.00.00 Link: https://lore.kernel.org/r/20191226111333.26131-11-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-02scsi: mpt3sas: Remove usage of device_busy counterSreekanth Reddy
Remove usage of device_busy counter from driver. Instead of device_busy counter now driver uses 'nr_active' counter of request_queue to get the number of inflight request for a LUN. Link: https://lore.kernel.org/r/20191226111333.26131-10-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-02scsi: mpt3sas: Print function name in which cmd timed outSreekanth Reddy
Print the function name in which MPT command got timed out. This will facilitate debugging in which path corresponding MPT command got timeout in first failure instance of log itself. Link: https://lore.kernel.org/r/20191226111333.26131-9-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-02scsi: mpt3sas: Optimize mpt3sas driver loggingSreekanth Reddy
This improves mpt3sas driver default debug information collection and allows for a higher percentage of issues being able to be resolved with a first-time data capture. However, this improvement to balance the amount of debug data captured with the performance of driver. Enabled below print messages with out affecting the IO performance, 1. When task abort TM is received then print IO commands's timeout value and how much time this command has been outstanding. 2. Whenever hard reset occurs then print from where this hard reset has been issued. 3. Failure message should be displayed for failure scenarios without any logging level. 4. Added a print after driver successfully register or unregistered a target drive with the SML. This print will be useful for debugging the issue where the drive addition or deletion is hanging at SML. 5. During driver load time print request, reply, sense and config page pool's information such as its address, length and size. Also printed sg_tablesize information. Link: https://lore.kernel.org/r/20191226111333.26131-8-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-02scsi: mpt3sas: print in which path firmware fault occurredSreekanth Reddy
When Firmware fault occurs then print in which path firmware fault has occurred. This will be useful while debugging the firmware fault issues. Link: https://lore.kernel.org/r/20191226111333.26131-7-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-02scsi: mpt3sas: Handle CoreDump state from watchdog threadSreekanth Reddy
Watchdog thread polls for IOC state every 1 second. If it detects that IOC state is in CoreDump state then it immediately stops the IOs and also clears the outstanding commands issued to the HBA firmware and then it will poll for IOC state to be out of CoreDump state and once it detects that IOC state is changed from CoreDump state to Fault state (or) CoreDumpTOSec number of seconds are elapsed then it will issue host reset operation and moves the IOC state to Operational state and resumes the IOs. Whenever any TM is received from SML then if driver detects the IOC state is in CoreDump state then it will wait for CoreDump state to be cleared and will host reset operation. Link: https://lore.kernel.org/r/20191226111333.26131-6-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-02scsi: mpt3sas: Add support IOCs new state named COREDUMPSreekanth Reddy
New feature is added in HBA firmware where it copies the collected firmware logs in flash region named 'CoreDump' whenever HBA firmware faults occur. For copying the logs to CoreDump flash region firmware needs some time and hence it has introduced a new IOC state named "CoreDump" State. Whenever driver detects the CoreDump state then it means that some firmware fault has occurred and firmware is copying the logs to the coredump flash region. During this time driver should not perform any operation with the HBA, driver should wait for HBA firmware to move the IOC state from 'CoreDump' state to 'Fault' state once it's done with copying the logs to coredump region. Once driver detects the Fault state then it will issue the diag reset/host reset operation to move the IOC state from Fault to Operational state. Here the valid IOC state transactions w.r.t to this CoreDump state feature, Operational -> Fault: The IOC transitions to the Fault state when an operational error occurs AND CoreDump is not supported (or disabled) by the firmware(FW). Operational -> CoreDump: The IOC transitions to the CoreDump state when an operational error occurs AND CoreDump is supported & enabled by the FW. CoreDump -> Fault: A transition from CoreDump state to Fault state happens when the FW completes the CoreDump collection. CoreDump -> Reset: A transition out of the CoreDump state happens when the host sets the Reset Adapter bit in the System Diagnostic Register (Hard Reset). This reset action indicates that CoreDump took longer than the host time out. Firmware informs the driver about the maximum time that driver has to wait for firmware to transition the IOC state from 'CoreDump' to 'FAULT' state through 'CoreDumpTOSec' field of ManufacturingPage11 page. if this 'CoreDumpTOSec' field value is zero then driver will wait for max 15 seconds. Driver informs the HBA firmware that it supports this new IOC state named 'CoreDump' state by enabling COREDUMP_ENABLE flag in ConfigurationFlags field of ioc init request message. Current patch handles the CoreDump state only during HBA initialization and release scenarios where watchdog thread (which polls the IOC state in every one second) is disabled. Next subsequent patch handle the CoreDump state when watchdog thread is enabled. During HBA initialization or release execution time if driver detects the CoreDump state then driver will wait for maximum CoreDumpTOSec value seconds for FW to copy the logs. After that it will issue the diag reset operation to move the IOC state to Operational state. Link: https://lore.kernel.org/r/20191226111333.26131-5-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-02scsi: mpt3sas: renamed _base_after_reset_handler functionSreekanth Reddy
Renamed _base_after_reset_handler function to _base_clear_outstanding_commands so that it can be used in multiple scenarios with suitable name which matches with the operation it does. Also renamed its child functions. No functional changes. Link: https://lore.kernel.org/r/20191226111333.26131-4-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-02scsi: mpt3sas: Add support for NVMe shutdownSreekanth Reddy
Introduce function _scsih_nvme_shutdown() to issue IO Unit Control message to IOC firmware with operation code 'shutdown'. This causes IOC firmware to issue NVMe shutdown commands to all NVMe drives attached to it. NVMe Shutdown: NVMe devices need to have a specific shutdown sequence performed before power is removed. For this, the IOC firmware needs to be notified when the system is being shutdown. So during the system shutdown time, driver issues an IO Unit Control request with operation code MPI26_CTRL_OP_SHUTDOWN to inform firmware that a shutdown is initiated. This shutdown command is issued only if NVMe devices are attached to the controller. During each NVMe device addition, driver reads pcie device page2 to get shutdown latency (e.g. drive's RTD3 Entry Latency) and updates the max latency value among the added NVMe drives in ioc->max_shutdown_latency. This is used as the timeout value for IO Unit Control command at the time of shutdown. When a NVMe drive is removed and its shutdown latency matches which ioc->max_shutdown_latency then ioc->max_shutdown_latency is updated to next max value (by iterating over the list of available devices). If the shutdown latency is 0, then default timeout is set to six seconds. Link: https://lore.kernel.org/r/20191226111333.26131-3-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-02scsi: mpt3sas: Update MPI Headers to v02.00.57Sreekanth Reddy
Update MPI Headers to version 02.00.57. Link: https://lore.kernel.org/r/20191226111333.26131-2-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-12-16scsi: mpt3sas: Fix double free in attach error handlingDan Carpenter
The caller also calls _base_release_memory_pools() on error so it leads to a number of double frees: drivers/scsi/mpt3sas/mpt3sas_base.c:7207 mpt3sas_base_attach() warn: 'ioc->chain_dma_pool' double freed drivers/scsi/mpt3sas/mpt3sas_base.c:7207 mpt3sas_base_attach() warn: 'ioc->hpr_lookup' double freed drivers/scsi/mpt3sas/mpt3sas_base.c:7207 mpt3sas_base_attach() warn: 'ioc->internal_lookup' double freed drivers/scsi/mpt3sas/mpt3sas_base.c:7207 mpt3sas_base_attach() warn: 'ioc->pcie_sgl_dma_pool' double freed drivers/scsi/mpt3sas/mpt3sas_base.c:7207 mpt3sas_base_attach() warn: 'ioc->reply_dma_pool' double freed drivers/scsi/mpt3sas/mpt3sas_base.c:7207 mpt3sas_base_attach() warn: 'ioc->reply_free_dma_pool' double freed drivers/scsi/mpt3sas/mpt3sas_base.c:7207 mpt3sas_base_attach() warn: 'ioc->reply_post_free_array_dma_pool' double freed drivers/scsi/mpt3sas/mpt3sas_base.c:7207 mpt3sas_base_attach() warn: 'ioc->reply_post_free_dma_pool' double freed drivers/scsi/mpt3sas/mpt3sas_base.c:7207 mpt3sas_base_attach() warn: 'ioc->sense_dma_pool' double freed Fixes: 74522a92bbf0 ("scsi: mpt3sas: Optimize I/O memory consumption in driver.") Link: https://lore.kernel.org/r/20191203093652.gyntgvnkw2udatyc@kili.mountain Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-10-24scsi: mpt3sas: change allocation optionTomas Henzl
From an interrupt handler path memory may be allocated using GFP_KERNEL, replace it with GFP_ATOMIC. _base_interrupt->_scsih_io_done->_scsih_smart_predicted_fault Link: https://lore.kernel.org/r/20191024152835.6177-1-thenzl@redhat.com Signed-off-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-10-09scsi: mpt3sas: Clean up some indentingDan Carpenter
This line is indented too far so it's a bit confusing. Link: https://lore.kernel.org/r/20191004100615.GA823@mwanda Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-30scsi: mpt3sas: Bump mpt3sas driver version to 32.100.00.00Sreekanth Reddy
Bump mpt3sas driver version to 32.100.00.00 Link: https://lore.kernel.org/r/1568379890-18347-14-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-30scsi: mpt3sas: Fix module parameter max_msix_vectorsSreekanth Reddy
Load driver with module parameter "max_msix_vectors". Value provided in module parameter is not used by mpt3sas driver. Driver loads with max controller supported MSI-X value. In _base_alloc_irq_vectors use reply_queue_count which is determined using user provided msix value insted of ioc->msix_vector_count which tells max supported msix value of the controller. Link: https://lore.kernel.org/r/1568379890-18347-13-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-30scsi: mpt3sas: Reject NVMe Encap cmnds to unsupported HBASreekanth Reddy
If any faulty application issues an NVMe Encapsulated commands to HBA which doesn't support NVMe protocol then driver should return the command as invalid with the following message. "HBA doesn't support NVMe. Rejecting NVMe Encapsulated request." Otherwise below page fault kernel panic will be observed while building the PRPs as there is no PRP pools allocated for the HBA which doesn't support NVMe drives. RIP: 0010:_base_build_nvme_prp+0x3b/0xf0 [mpt3sas] Call Trace: _ctl_do_mpt_command+0x931/0x1120 [mpt3sas] _ctl_ioctl_main.isra.11+0xa28/0x11e0 [mpt3sas] ? prepare_to_wait+0xb0/0xb0 ? tty_ldisc_deref+0x16/0x20 _ctl_ioctl+0x1a/0x20 [mpt3sas] do_vfs_ioctl+0xaa/0x620 ? vfs_read+0x117/0x140 ksys_ioctl+0x67/0x90 __x64_sys_ioctl+0x1a/0x20 do_syscall_64+0x60/0x190 entry_SYSCALL_64_after_hwframe+0x44/0xa9 [mkp: tweaked error string] Link: https://lore.kernel.org/r/1568379890-18347-12-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-30scsi: mpt3sas: Use Component img header to get Package verSreekanth Reddy
The firmware image layout has been changed for Aero controllers. All compatible HBAs have to get Firmware Package version from Component Image Header layout. The Signature field in FW header is set to 0xEB000042 for products compatible with Component Image Header. For compatible controllers, driver fetches firmware package version from ApplicationSpecific field of Component Image Header. Link: https://lore.kernel.org/r/1568379890-18347-11-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-30scsi: mpt3sas: Fail release cmnd if diag buffer is releasedSreekanth Reddy
Return the diag buffer release command with -EINVAL status if the buffer is already released. Link: https://lore.kernel.org/r/1568379890-18347-10-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-30scsi: mpt3sas: Add app owned flag support for diag bufferSreekanth Reddy
Added a new status flag named MPT3_DIAG_BUFFER_IS_APP_OWNED and it will set whenever application registers the diag buffer & it will be cleared when application unregisters the buffer. When this flag is enabled, and if application issues diag buffer register command without releasing the buffer, then register command will be failed with -EINVAL status by saying that this buffer is already registered by the application. When user issues a trace buffer register command through sysfs parameter, and if trace buffer is in released stated but not yet unregistered by the application which was owning it, then driver will unregister the buffer by itself and freshly register the 1MB sized trace buffer with the HBA firmware. Link: https://lore.kernel.org/r/1568379890-18347-9-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-30scsi: mpt3sas: Reuse diag buffer allocated at load timeSreekanth Reddy
The diag buffer which is allocated during driver load time or through sysfs parameter is marked as driver allocated diag buffer. MPT3_DIAG_BUFFER_IS_DRIVER_ALLOCATED bit will be set for this buffer. This buffer won't be de-allocated even when application issues unregister command, driver just clears the registered status bit. Same buffer will be reused while re-registering the same diag buffer type by any application. While re-registering the same diag buffer type application has to register with the same size that the buffer was allocated during driver load time. This buffer size can be read by the application by issuing diag 'query' command. This always makes sure that the memory is available for applications for collecting the firmware logs. Only thing is that this won't allow the application to re-register the diag buffer with different size, but the buffer size which is allocated during driver load time will be enough for most of the cases for collecting the firmware logs. Link: https://lore.kernel.org/r/1568379890-18347-8-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-30scsi: mpt3sas: clear release bit when buffer reregisteredSreekanth Reddy
Clear MPT3_DIAG_BUFFER_IS_RELEASED bit once diag buffer is re-registered after reading the buffer, else driver won't release the buffer and return the 'diag release' command with -EINVAL status saying that buffer is already released. Link: https://lore.kernel.org/r/1568379890-18347-7-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-30scsi: mpt3sas: Maintain owner of buffer through UniqueIDSreekanth Reddy
Application A has registered a diag buffer and looking for particular event to happen to release & read the trace buffer. Meanwhile application B has unregistered the diag buffer and now Application A can't get the required diag buffer. So proper diag buffer ownership is missing. Each application has to maintain its own Unique ID. Now driver has to save the Application's UniqueID for each diag buffer type when diag buffer is registered. And driver has to allow 'release', 'read' & 'unregister' diag commands only if application's UniqueID matches with saved UniqueID for the corresponding diag buffer type. When diag buffer is registered by the driver, then the UniqueID saved by the driver is "BRCM" (i.e. 0x4252434D) for SAS3 and above generations HBA devices. For SAS2 HBAs, driver keeps the legacy UniqueID 0x07075900 for maintaining compatibility with the legacy SAS2 application and this improvement won't be applicable for SAS2 HBA devices. Any application can own the buffer registered by the driver by sending diag register request to driver with same buffer type and size (Application can get the buffer size by sending 'query' command). Then driver changes the ownership of the buffer by saving application's UniqueID for that corresponding buffer type. Also, application can re-register the diag buffer with same size without un-registering it, but diag buffer should be released before re-registering it. By allowing this, driver no need to deallocate and allocate a new buffer for re-register command, same buffer can be re-used. Link: https://lore.kernel.org/r/1568379890-18347-6-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-30scsi: mpt3sas: Free diag buffer without any status checkSreekanth Reddy
Memory leak can happen when diag buffer is released but not unregistered (where buffer is deallocated) by the user. During module unload time driver is not deallocating the buffer if the buffer is in released state. Deallocate the diag buffer during module unload time without any diag buffer status checks. Link: https://lore.kernel.org/r/1568379890-18347-5-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-30scsi: mpt3sas: Fix clear pending bit in ioctl statusSreekanth Reddy
When user issues diag register command from application with required size, and if driver unable to allocate the memory, then it will fail the register command. While failing the register command, driver is not currently clearing MPT3_CMD_PENDING bit in ctl_cmds.status variable which was set before trying to allocate the memory. As this bit is set, subsequent register command will be failed with BUSY status even when user wants to register the trace buffer will less memory. Clear MPT3_CMD_PENDING bit in ctl_cmds.status before returning the diag register command with no memory status. Link: https://lore.kernel.org/r/1568379890-18347-4-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-30scsi: mpt3sas: Display message before releasing diag bufferSreekanth Reddy
Display message before releasing the diag buffer so that user knows which event caused the release of diag buffer. Releasing of diag buffer means HBA firmware stops posting the firmware logs on the registered diag buffer. Link: https://lore.kernel.org/r/1568379890-18347-3-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-30scsi: mpt3sas: Register trace buffer based on NVDATA settingsSreekanth Reddy
Currently if user wishes to enable the host trace buffer during driver load time, then user has to load the driver with module parameter 'diag_buffer_enable' set to one. Alternatively now the user can enable host trace buffer by enabling the following fields in manufacturing page11 in NVDATA (nvdata xml is used while building HBA firmware image): * HostTraceBufferMaxSizeKB - Maximum trace buffer size in KB that host can allocate, * HostTraceBufferMinSizeKB - Minimum trace buffer size in KB atleast host should allocate, * HostTraceBufferDecrementSizeKB - size by which host can reduce from buffer size and retry the buffer allocation when buffer allocation failed with previous calculated buffer size. The driver will register the trace buffer automatically without any module parameter during boot time when above fields are enabled in manufacturing page11 in HBA firmware. Driver follows the following algorithm for enabling the host trace buffer during driver load time: * If user has loaded the driver with module parameter 'diag_buffer_enable' set to one, then driver allocates 2MB buffer and registers this buffer with HBA firmware for capturing the firmware trace logs. * Else driver reads manufacture page11 data and checks whether HostTraceBufferMaxSizeKB filed is zero or not? - If HostTraceBufferMaxSizeKB is non-zero then driver tries to allocate HostTraceBufferMaxSizeKB size of memory. If the buffer allocation is successful, then it will register this buffer with HBA firmware, else in a loop the driver will try again by reducing the current buffer size with HostTraceBufferDecrementSizeKB size until memory allocation is successful or buffer size falls below HostTraceBufferMinSizeKB. If the memory allocation is successful, then the buffer will be registered with the firmware. Else, if the buffer size falls below the HostTraceBufferMinSizeKB, then driver won't register trace buffer with HBA firmware. - If HostTraceBufferMaxSizeKB is zero, then driver won't register trace buffer with HBA firmware. Link: https://lore.kernel.org/r/1568379890-18347-2-git-send-email-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-23Merge tag 'pci-v5.4-changes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: "Enumeration: - Consolidate _HPP/_HPX stuff in pci-acpi.c and simplify it (Krzysztof Wilczynski) - Fix incorrect PCIe device types and remove dev->has_secondary_link to simplify code that deals with upstream/downstream ports (Mika Westerberg) - After suspend, restore Resizable BAR size bits correctly for 1MB BARs (Sumit Saxena) - Enable PCI_MSI_IRQ_DOMAIN support for RISC-V (Wesley Terpstra) Virtualization: - Add ACS quirks for iProc PAXB (Abhinav Ratna), Amazon Annapurna Labs (Ali Saidi) - Move sysfs SR-IOV functions to iov.c (Kelsey Skunberg) - Remove group write permissions from sysfs sriov_numvfs, sriov_drivers_autoprobe (Kelsey Skunberg) Hotplug: - Simplify pciehp indicator control (Denis Efremov) Peer-to-peer DMA: - Allow P2P DMA between root ports for whitelisted bridges (Logan Gunthorpe) - Whitelist some Intel host bridges for P2P DMA (Logan Gunthorpe) - DMA map P2P DMA requests that traverse host bridge (Logan Gunthorpe) Amazon Annapurna Labs host bridge driver: - Add DT binding and controller driver (Jonathan Chocron) Hyper-V host bridge driver: - Fix hv_pci_dev->pci_slot use-after-free (Dexuan Cui) - Fix PCI domain number collisions (Haiyang Zhang) - Use instance ID bytes 4 & 5 as PCI domain numbers (Haiyang Zhang) - Fix build errors on non-SYSFS config (Randy Dunlap) i.MX6 host bridge driver: - Limit DBI register length (Stefan Agner) Intel VMD host bridge driver: - Fix config addressing issues (Jon Derrick) Layerscape host bridge driver: - Add bar_fixed_64bit property to endpoint driver (Xiaowei Bao) - Add CONFIG_PCI_LAYERSCAPE_EP to build EP/RC drivers separately (Xiaowei Bao) Mediatek host bridge driver: - Add MT7629 controller support (Jianjun Wang) Mobiveil host bridge driver: - Fix CPU base address setup (Hou Zhiqiang) - Make "num-lanes" property optional (Hou Zhiqiang) Tegra host bridge driver: - Fix OF node reference leak (Nishka Dasgupta) - Disable MSI for root ports to work around design problem (Vidya Sagar) - Add Tegra194 DT binding and controller support (Vidya Sagar) - Add support for sideband pins and slot regulators (Vidya Sagar) - Add PIPE2UPHY support (Vidya Sagar) Misc: - Remove unused pci_block_cfg_access() et al (Kelsey Skunberg) - Unexport pci_bus_get(), etc (Kelsey Skunberg) - Hide PM, VC, link speed, ATS, ECRC, PTM constants and interfaces in the PCI core (Kelsey Skunberg) - Clean up sysfs DEVICE_ATTR() usage (Kelsey Skunberg) - Mark expected switch fall-through (Gustavo A. R. Silva) - Propagate errors for optional regulators and PHYs (Thierry Reding) - Fix kernel command line resource_alignment parameter issues (Logan Gunthorpe)" * tag 'pci-v5.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (112 commits) PCI: Add pci_irq_vector() and other stubs when !CONFIG_PCI arm64: tegra: Add PCIe slot supply information in p2972-0000 platform arm64: tegra: Add configuration for PCIe C5 sideband signals PCI: tegra: Add support to enable slot regulators PCI: tegra: Add support to configure sideband pins PCI: vmd: Fix shadow offsets to reflect spec changes PCI: vmd: Fix config addressing when using bus offsets PCI: dwc: Add validation that PCIe core is set to correct mode PCI: dwc: al: Add Amazon Annapurna Labs PCIe controller driver dt-bindings: PCI: Add Amazon's Annapurna Labs PCIe host bridge binding PCI: Add quirk to disable MSI-X support for Amazon's Annapurna Labs Root Port PCI/VPD: Prevent VPD access for Amazon's Annapurna Labs Root Port PCI: Add ACS quirk for Amazon Annapurna Labs root ports PCI: Add Amazon's Annapurna Labs vendor ID MAINTAINERS: Add PCI native host/endpoint controllers designated reviewer PCI: hv: Use bytes 4 and 5 from instance ID as the PCI domain numbers dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries dt-bindings: PCI: tegra: Add sideband pins configuration entries PCI: tegra: Add Tegra194 PCIe support PCI: Get rid of dev->has_secondary_link flag ...
2019-09-21Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds
Pull SCSI updates from James Bottomley: "This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi, lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates. The only core change this time around is the addition of request batching for virtio. Since batching requires an additional flag to use, it should be invisible to the rest of the drivers" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (264 commits) scsi: hisi_sas: Fix the conflict between device gone and host reset scsi: hisi_sas: Add BIST support for phy loopback scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation scsi: hisi_sas: Remove some unused function arguments scsi: hisi_sas: Remove redundant work declaration scsi: hisi_sas: Remove hisi_sas_hw.slot_complete scsi: hisi_sas: Assign NCQ tag for all NCQ commands scsi: hisi_sas: Update all the registers after suspend and resume scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset() scsi: hisi_sas: add debugfs auto-trigger for internal abort time out scsi: virtio_scsi: unplug LUNs when events missed scsi: scsi_dh_rdac: zero cdb in send_mode_select() scsi: fcoe: fix null-ptr-deref Read in fc_release_transport scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code scsi: ufs: Use kmemdup in ufshcd_read_string_desc() ...
2019-08-29scsi: mpt3sas: Introduce module parameter to override queue depthSreekanth Reddy
This patch provides a module parameter and sysfs interface to select whether the queue depth for each device should be based on the protocol-specific value set by the driver (the default) or the maximum supported by the controller (can_queue). Although we have a sysfs interface per sdev to change the queue depth of individual scsi devices, this implementation provides a single sysfs entry per shost to switch between the controller max and the driver default. [mkp: tweaked commit desc] Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-06 18:20:16 +0000