| Age | Commit message (Collapse) | Author |
|---|
|
After link bounce in a NVME Pt2Pt config, the driver managed to map the
same nport twice, resulting in multiple device nodes for the same
namespace.
In Pt2Pt, the driver must send PRLI's for both (scsi) FCP and NVME
rather than using fabric aids. The driver was inconsistent on handling
various PRLI completions, especially rejects, which had reject codes
cross the different protocol PRLI completions.
Fixed to perform the following: if nvmet mode (fc port can only be a
nvme target) - rejects all unsolicitly FCP PRLI's. Never issues a FCP
PRLI.
The multiple protocol PRLI's are sent simultaneously. However, driver
will now only state transition after both PRLI's are complete. New flags
were added to aid tracking the responses from the different PRLI's.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the switch blade is pulled out then plugged back in, the driver
does not issue a PLOGI to the target
When the switch blade is pulled out, it does not reset the link. The
driver ends up issuing a LOGO to the target, and finally sees devloss.
Since the driver believes that a LOGO is outstanding, it does not issue
a PLOGI to the target upon link up
Correct by placing the ndlp in UNUSED state When devloss happens in
LOGO_ISSUE state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver does not discover targets when in loop mode.
The NLP type is correctly getting set when a fabric connection is
detected but, not for loop. The unknown NLP type means that the driver
does not issue a PRLI when in loop topology. Thus target discovery
fails.
Fix by checking the topology during discovery. If it is loop, set the
NLP FC4 type to FCP.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We might have a NULL pring in lpfc_els_abort(), for example on error
recovery path, since queues are destroyed during error recovery
mechanism.
In this case, we should just drop the abort since the queues will be
recreated anyway. This patch just verifies for NULL pointer and stop the
abortion of the queue in case of a NULL pring.
Also, this patch converts return type of lpfc_els_abort() from int to
void, since it's not checked anywhere.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Reported-by: Naresh Bannoth <nbannoth@in.ibm.com>
Tested-by: Raphael Silva <raphasil@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Code review of NVMEI's FC_PORT_ROLE_NVME_DISCOVERY looked wrong.
Discussions with storage architecture team clarified NVMEI's audit of
the PRLI response port roles. Following up discussion with code review
showed a few minor corrections were required - especially in
anticipation of NVME auto discovery.
During PRLI, NVMEI should sent prli_init - which it it does. NVMET
should send prli_tgt and prli_disc - which it does. When NVMEI receives
a PRLI Response now, it audits the incoming target bits and stores the
attributes in the corresponding NDLP. Later, when NVMEI registers the
NVME rport, it uses the stored ndlp attributes to set the rport
port_roles correctly.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
NVMET didn't have any RSCN handling at all and
would not execute implicit LOGO when receiving a PLOGI
from an rport that NVMET had in state UNMAPPED.
Clean up the logic in lpfc_nlp_state_cleanup for
initiators (FCP and NVME). NVMET should not respond to
RSCN including allocating new ndlps so this code was
conditionalized when nvmet_support is true. The check
for NLP_RCV_PLOGI in lpfc_setup_disc_node was moved
below the check for nvmet_support to allow the NVMET
to recover initiator nodes correctly. The implicit
logo was introduced with lpfc_rcv_plogi when NVMET gets
a PLOGI on an ndlp in UNMAPPED state. The RSCN handling
was modified to not respond to an RSCN in NVMET. Instead
NVMET sends a GID_FT and determines if an NVMEP_INITIATOR
it has is UNMAPPED but no longer in the zone membership.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
Update copyrights to 2017 for all files touched in this patch set
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
NVME Target: Merge into FC discovery
Adds NVME PRLI handling and Nameserver registrations for NVME
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
NVME Initiator: Tie in to NVME Fabrics nvme_fc LLDD initiator api
Adds the routines to:
- register and deregister the FC port as a nvme-fc initiator localport
- register and deregister remote FC ports as a nvme-fc remoteport
- binding of nvme queues to adapter WQs
- send/perform NVME LS's
- send/perform NVME FCP initiator io operations
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
NVME Initiator: Merge into FC discovery
Adds NVME PRLI support and Nameserver registrations and Queries for NVME
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
NVME Initiator: Base modifications
This patch adds base modifications for NVME initiator support.
The base modifications consist of:
- Formal split of SLI3 rings from SLI-4 WQs (sometimes referred to as
rings as well) as implementation now widely varies between the two.
- Addition of configuration modes:
SCSI initiator only; NVME initiator only; NVME target only; and
SCSI and NVME initiator.
The configuration mode drives overall adapter configuration,
offloads enabled, and resource splits.
NVME support is only available on SLI-4 devices and newer fw.
- Implements the following based on configuration mode:
- Exchange resources are split by protocol; Obviously, if only
1 mode, then no split occurs. Default is 50/50. module attribute
allows tuning.
- Pools and config parameters are separated per-protocol
- Each protocol has it's own set of queues, but share interrupt
vectors.
SCSI:
SLI3 devices have few queues and the original style of queue
allocation remains.
SLI4 devices piggy back on an "io-channel" concept that
eventually needs to merge with scsi-mq/blk-mq support (it is
underway). For now, the paradigm continues as it existed
prior. io channel allocates N msix and N WQs (N=4 default)
and either round robins or uses cpu # modulo N for scheduling.
A bunch of module parameters allow the configuration to be
tuned.
NVME (initiator):
Allocates an msix per cpu (or whatever pci_alloc_irq_vectors
gets)
Allocates a WQ per cpu, and maps the WQs to msix on a WQ #
modulo msix vector count basis.
Module parameters exist to cap/control the config if desired.
- Each protocol has its own buffer and dma pools.
I apologize for the size of the patch.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
----
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After a link bounce, when a remote port issues a LOGO while a REGLOGIN
is pending on that port, the driver does not clean up the ndlp
structure. May result in stack traces in the console log.
Fix: Clear the NLP_REG_LOGIN_SEND flag on the ndlp in the routine
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix mbox reuse in PLOGI completion. Moved allocations so that buffer
properly init'd.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix RegLogin failed error seen on Lancer FC during port bounce
Fix the statemachine and ref counting.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix the FLOGI discovery logic to comply with T11 standards
We weren't properly setting fabric parameters, such as R_A_TOV and E_D_TOV,
when we registered the vfi object in default configs and pt2pt configs.
Revise to now pass service params with the values to the firmware and
ensure they are reset on link bounce. Required reworking the call sequence
in the discovery threads.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove set but not used variables.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
The domain controller PLOGI's concurrent with prior LOGO's/unreg_rpi's
completing created a race condition where driver rpi ref count can
inadvertantly hit 0 and the rpi attempted to be freed. This error
sometimes resulted in Warning messages indicating kref.h via
lfpc_nlp_get+0x128.
Correct by dropping any new PLOGI until the prior nport state has settled.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
We inadvertantly took the path to recreate the vport while in a
driver teardown path
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Update copyright to 2015
Signed-off-by: Dick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Dick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Fixed High priority issues from lpfc given by fortify source code scan.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Dick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
modifications
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fixed NMI watch dog panic's when resetting the hba.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
deferred removal.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Make compliant with FC specs by sending LOGO after ABTS timeouts
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Locking fix and Memory leak Fixes
- Fix Locking code raises IRQ twice (NA)
- Fix mailbox and vpi memory leaks (126818)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
SLI related fixes:
- Fix REG_RPI fails on SLI4 HBA putting NPort into NPR state (126230)
- Fix ELS FDISC failing with local reject / invalid RPI. (126350)
- Fix reset port when reset is needed during fw_dump (125807)
- Fix unbounded firmware revision string from port cause panic (126560)
- Fix driver behavior when receiving an ADISC (126654)
- Fix driver not returning when bad ndlp found in abts error event
handling (126209)
- Add more driver logs in area of SLI4 port error attention and reset
recovery (126813, 124466)
- Fix failure in handling large CQ/EQ identifiers in an IOV
environment (126856)
- Fix for driver using duplicate RPIs after lancer port reset (126723)
- Clear vport->fc_myDID in lpfc_els_issue_fdisc to guarentee a
zero SID (126779, 126897)
- Fix for SLI4 Port delivery for BLS ABORT ACC (126289)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
FC and SCSI Discovery Fixes:
- Clear the virtual fabrics bit (word 1 bit 30) when sending the FLOGI
and FDISC. (CR 124339)
- Return a MLQUEUE_DEVICE_BUSY if the driver detects that an I/O is being
retried too quickly (CR 124668)
- Remove NDLP reference put in lpfc_cmpl_els_logo_acc for all but fabric
nodes (CR 123924)
- Only retry FDISCs every second and stop retrying after devloss number
of retries (CR 13939)
- Check to see if vports are unloading before adding them to the vport
work array. (CR 124996)
- Fixed illegal state transition during driver unload (CR 124191)
- Added missing protection on setting/clearing of vport->fc_flag bit (CR 126002)
- Set NPIV flag in lpfc_mbx_process_link_up for all ports sli3 and
above. (CR 126094)
- Clear FCP command bytes that are not used. (CR 126209)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch adds support for hardware that returns resource ids via
extents rather than contiguous ranges.
[jejb: checkpatch.pl fixes]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Miscellaneous Fixes and Corrections
- Remove the memset in the lpfc_sli4_remove_rpi_hdrs call.
- Correct swapping of SGE word 2 relative to offset value
- Reorganize CQ and EQ usage to comply with SLI4 Specification.
- Expand the driver to check the rn bit. Only detect an error if the error bit
is set and the RN bit is NOT set.
- If mailbox completion code is not success AND the mailbox status is success,
then and only then will the driver overwrite the mailbox status.
- When driver initializing device, if the device is on a PCIe bus, set
PCI's "needs fundamental reset" bit so that EEH uses fundamental reset
instead of hot reset for recovery.
- Prevent driver from using new WWN when changed in firmware (until driver
reload)
- When HBA reports maximum SGE size > 0xffffffff (infinite), override
with 0x80000000.
- Fixed potential missed SLI4 device initialization failure conditions.
- Added 100ms delay before driver action following IF_TYPE_2 function reset.
- Reverted patch to UNREG/REG on PLOGI to mapped/unmapped node.
- Add a check for the CVL received flag in the fcf inuse routine to avoid
unregistering the fcf if Devloss fires before Delay discover timer fires.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
FC Discovery changes
- Treat received PLOGI while logged in as a relogin (unregister and reregister).
- Added a timer to delay Nport discovery when clean bit is cleared and Fabric
portname/nodename/FCID is changed.
- Invalidate Port's DID when receiving PLOGI from p2p port with CONFIG_PORT
mailbox command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Updated commands used for ELS to utilize VPI
Allocate RPI at node creation time and pass in ELS commnads.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Retry PLOGI up to 48 times when LS_RJT reason is
"Unable to supply requested data."
- When dev loss timeout occures do not change state if there
is an outstanding REG_LOGIN.
- Add logic to ignore REG_LOGIN completion if discovery is
restarted while waiting for REG_LOGIN.
- Only change state on REG_LOGIN completion if still in
state waiting for REG_LOGIN completion.
- Only send ADISCs to FCP-2 Targets (not Initiators).
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Add code to prevent unreg_vpi mailbox command from failing.
- Add code to reset the HBA if unreg_vpi mailbox fails with busy status.
- Remove code that was clearing the nlp_type stored during rport discovery.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Enable NPIV by default.
- Added code to handle unsolicited LOGO on physical port.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
Discovery relates changes:
- Separated VPI_REGISTERED state of physical port into VFI_REGISTERED and
VPI_REGISTERED state so that driver can unregister physical port VPI
independent of VFI.
- Add code to unregister, re-init and re-register physical port VPI
when physical port NportID change.
- Add code to unregister and re-register VPI of a vport when its Nport
ID change.
- Add code in FDISC completion path to re-start FLOGI discovery when
a FDISC complete with LOGIN_REQUIRED reason code.
- Fix a memory leak in lpfc_init_vpi_cmpl
- Add code to start a timer for vport to retry FDISC when CVL is received
by a vport or physical port. If all Nports receive CVLs, then all timers
are cancelled and a logical link level discovery will be started after
one second.
- Flush ELS commands after killing all delayed ELS commands.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fix hardware/SLI relates issues:
- Handle XB bit so that ELS XRIs are not prematurely released.
- Handle XB bit so that FCP XRIs are not prematurely released.
- Define new security SLI Commands.
- Remove unused security SLI commands
- Skip receive data size parameter check on received FLOGI.
- Added LPFC_USE_FCPWQIDX flag to iocb to force SLI layer
to submit abort WQE on same WQ as the command WQE.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
FC protocol fixes.
- Fix send sequence logic to handle multi SGL IOCBs.
- Fix FDISC completion always setting VPORT state to failed.
- Ported the fix on reporting of max_vpi to uppper layer.
- Fix incorrect number of Vports allowed to be created.
- Fixed Dead FCoE port after creating vports.
- Added handling of ELS request for Reinstate Recovery Qualifier (RRQ)
- Handle unsolicited CT exchange initiator receiving CT exchange ABTS
- Migrate LUN queue depth ramp up code to scsi mid-layer.
- Made ABTS WQE go to the same WQ as the WQE to be aborted.
- Fix Vport does not rediscover after FCF goes away.
- Fixed lpfc_unreg_vfi failure after devloss timeout.
- Fixed RPI bit leak.
- Fix hbq pointer corruption during target discovery.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Contains the following changes:
- Force vport to send LOGO to fabric controller when deleting vport
- Fixed driver failing to register login when a PLOGI is received
- Fixes for FIP discovery
- Added stricter checks for FCF addressing mode
- Added code to send only FLOGI, FDISC and LOGO to Fabric controller as FIP
- Fixed handling of LOGO from Fabric port
- Fixed consecutive link up events skipped link_down processing
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
