| Age | Commit message (Collapse) | Author |
|---|
|
An opal_msg of type OPAL_MSG_ASYNC_COMP contains the return code in the
params[1] struct member. However this isn't intuitive or obvious when
reading the code and requires that a user look at the skiboot
documentation or opal-api.h to verify this.
Add an inline function to get the return code from an opal_msg and update
call sites accordingly.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This module is loaded by the related mfd driver which has
the needed MODULE_DEVICE_TABLE(i2c,...).
This patch fix the modalias when the rtc driver is built
as a module, so the right name is used.
Everything operates correctly when this module is builtin.
Fixes: esdc59ed3865 ("rtc: add RTC driver for TPS6586x")
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The added support for SPI mode made it possible to configure the driver
when I2C is disabled, leaving an unused device table:
drivers/rtc/rtc-rv3029c2.c:794:29: error: 'rv3029_id' defined but not used [-Werror=unused-variable]
This moves the table inside of the #ifdef section that has the
only user, to avoid the harmless warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d08f50dd0afc ("rtc: rv3029: Add support of RV3049")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The R2025SD chip, according to its data sheet, sets the /XST
bit to zero if the oscillator stops. Hence the check for this
condition was wrong.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add the alarm IRQ functionality.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The bin2bcd function in set_time is uncorrect on weekdays as the
bit mask should be done at the end of arithmetic operations.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The RTC RV3029 handles different types of alarms : seconds, minutes, ...
These alarms can be enabled or disabled individually using an AE_x bit
which is the last bit (BIT(7)) on each alarm registers.
To prepare the alarm IRQ support, the current code enables all the alarm
types by setting each AE_x to 1.
It also fixes others alarms issues :
- month and weekday errors : it was performing -1 instead of +1.
- wrong use of bit mask with bin2bcd
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Remove some checks from checkpatch such as spaces around arithmetic
operations or prefer "unsigned int".
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add support of Microcrystal RV3049 RTC (SPI) using regmap on the
RV3029 (I2C) driver.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
To add support of rv3049, the current driver is converted to use regmap.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
To prepare the use of regmap to add the support of RV-3049, all the
'i2c' in functions's names are removed.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
stmp3xxx_wdt_register() can fail as platform_device_alloc() or
platform_device_add() can fail. But when it fails it failed silently.
Lets print out an error message on failure so that user will atlest
know that there was some error.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The rtc->ops_lock would be accessed in ds3232_irq() without being
initialized as rtc_device_register() is called too late.
So move devm_rtc_device_register() just before registering irq handler
to initialize rtc->ops_lock earlier.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
If enable_irq_wake fails, we should return that error code so that
entering suspend fails. Otherwise we will get a WARNING along with
the hint of a unbalanced wake disable:
Unbalanced IRQ 37 wake disable
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
We program RTC time using SET_TIME_WRITE register and read the RTC
current time using CURRENT_TIME register. When we set the time by
writing into SET_TIME_WRITE Register and immediately try to read the
rtc time from CURRENT_TIME register, the previous old value is
returned instead of the new loaded time. This is because RTC takes
nearly 1 sec to update the new loaded value into the CURRENT_TIME
register. This behaviour is expected in our RTC IP.
This patch updates the driver to read the current time from SET_TIME_WRITE
register instead of CURRENT_TIME when rtc time is requested within an 1sec
period after setting the RTC time. Doing so will ensure the correct time is
given to the user.
Since there is a delay of 1sec in updating the CURRENT_TIME we are loading
set time +1sec while programming the SET_TIME_WRITE register, doing this
will give correct time without any delay when read from CURRENT_TIME.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The RTC core handles it since 6610e08 (RTC: Rework RTC code to use
timerqueue for events). So far, only the callbacks to the RTC core have
been removed, but not the handlers. Do this now.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The RTC core handles it since 6610e08 (RTC: Rework RTC code to use
timerqueue for events).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
This flag is a no-op now (see commit 47b0eeb3dc8a "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Michael Tatarinov <kukabu@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
This flag is a no-op now (see commit 47b0eeb3dc8a "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
This flag is a no-op now (see commit 47b0eeb3dc8a "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
It is suggested to program CALIB_WRITE register with the calibration
value before updating the SET_TIME_WRITE register, doing so will
clear the Tick Counter and force the next second to be signaled
exactly in 1 second.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
In order to conserve battery energy, during the PS operation,
it is expected that the supply for the battery-powered domain
to be switched from the battery (VCC_PSBATT) to (VCC_PSAUX) and
automatically be switched back to battery when VCC_PSAUX voltage
drops below a limit, doing so prevents the logic within
the battery-powered domain from functioning incorrectly.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
objtool reports the following warning:
drivers/rtc/rtc-ds1685.o: warning: objtool: ds1685_rtc_poweroff() falls through to next function ds1685_rtc_work_queue()
Similar to commit 361c6ed6b153 ("rtc: ds1685: actually spin forever in
poweroff error path"), there's another unreachable() annotation which is
actually reachable, which we missed the first time.
Actually spin forever to be consistent with the comment and to make the
unreachable() annotation guaranteed to be unreachable.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
This fix alters the ordering of the IRQ and device registrations in the RTC
driver probe function. This change will apply to the RTC driver that supports
both DA9052 and DA9053 PMICs.
A problem could occur with the existing RTC driver if:
A system is started from a cold boot using the PMIC RTC IRQ to initiate a
power on operation. For instance, if an RTC alarm is used to start a
platform from power off.
The existing driver IRQ is requested before the device has been properly
registered.
i.e.
ret = da9052_request_irq()
comes before
rtc->rtc = devm_rtc_device_register();
In this case, an interrupt exists before the device has been registered and
the IRQ handler can be called immediately: this can happen be before the
memory for rtc->rtc has been allocated. The IRQ handler da9052_rtc_irq()
contains the function call:
rtc_update_irq(rtc->rtc, 1, RTC_IRQF | RTC_AF);
which in turn tries to access the unavailable rtc->rtc.
The fix is to reorder the functions inside the RTC probe. The IRQ is
requested after the RTC device resource has been registered so that
da9052_request_irq() is the last thing to happen.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
enabled
If a previously-set alarm was disabled and then triggered, it may still
be pending when a new alarm is configured.
Then, if the alarm is enabled before the pending alarm is cleared, then
an interrupt is immediately raised.
Unfortunately, when the alarm is cleared and enabled during the same I²C
block write, the chip (at least the DS1339 I have) considers that the
alarm is enabled before it is cleared, and raises an interrupt.
This patch ensures that the pending alarm is cleared before the alarm is
enabled.
Signed-off-by: Nicolas Boullis <nboullis@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The i2c_smbus_read_i2c_block_data function returns 0 on success, not the
number of bytes written.
Hence, when there are 32 bytes or less to send, the
ds1307_native_smbus_write_block_data function returns 0 on success,
while it returns the number of bytes when there are more than 32.
The ds1307_write_block_data always returns the number of bytes on
success.
Signed-off-by: Nicolas Boullis <nboullis@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The valid range of day of week register for DS1302 is 1 to 7. But the
set_time callback for rtc-ds1302 attempts to write the value of
tm->tm_wday which is in the range 0 to 6. While the get_time callback
correctly decodes the register.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Sergey Yanovich <ynvich@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The set_time callback for rtc-ds1302 doesn't write clock registers
because the error check for the return value from spi_write_then_read()
is not correct. spi_write_then_read() which returns zero on success.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Sergey Yanovich <ynvich@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Handle the Oscillator Failure (OF) bit on each read of date-time.
If the OF is set, an error is returned (-EINVAL) instead of the date-time.
The OF bit is cleared each time the date is set.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
To enable the wakealarm, the device must be able to wakeup.
This is done by setting the device wakeup capability to true with
'device_init_wakeup' function.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Previous 'commit c3b79770e51a ("Expire alarms after the time is set")'
and 'commit 48e9766726eb ("remove disabled alarm functionality")' removed
the alarm support because the alarm irq was not functional.
Add the alarm IRQ functionality with newer functions than previous
code. Tested with 'rtctest' and the alarm is functional.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Replace the obsolete "simple_strtoul" function to "kstrtoul".
Remove some checkpatch's errors, warnings and checks :
- alignment with open parenthesis
- spaces around '<' and '<<'
- blank line after structure
- quoted string split across lines
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Replace bit shifts by BIT macro.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The driver used i2c_transfer methods to read and set date/time.
The smbus methods should be used.
This commit replaces i2c_transfer functions by i2c_smbus_XX_i2c_block_data
for reading and setting the datetime.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Remove the CONFIG_RTC_INTF_PROC and CONFIG_RTC_INTF_PROC_MODULE macro
which is not necessary anymore.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The driver used an old sysfs entry export.
Update it to use the DEVICE_ATTR_XX macro and remove the unnecessary
CONFIG_RTC_INTF_SYSFS macro.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Many drivers are defining a DRV_VERSION. This is often only used for
MODULE_VERSION and sometimes to print an info message at probe time. This
is kind of pointless as they are all versionned with the kernel anyway.
Also the core will print a message when a new rtc is found.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
mr is written twice with the same value, remove one of the
redundant assignments to mr.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
DS1302 is an half-duplex SPI device. The driver respects this fact now.
Pin configurations should be implemented using SPI subsystem.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
With commit 8bc2a40730ec ("rtc: ds1307: add support for the
DT property 'wakeup-source'") we lost the ability for rtc irq
functionality for devices that are actually hooked on a real IRQ
line and have capability to wakeup as well. This is not an expected
behavior. So, instead of just not requesting IRQ, skip the IRQ
requirement only if interrupts are not defined for the device.
Fixes: 8bc2a40730ec ("rtc: ds1307: add support for the DT property 'wakeup-source'")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Michael Lange <linuxstuff@milaw.biz>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
while retrieving temperature from ds3231, the result may be overflow
since s16 is too small for a multiplication with 250.
ie. if temp_buf[0] == 0x2d, the result (s16 temp) will be negative.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Michael Tatarinov <kukabu@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull more RTC updates from Alexandre Belloni:
"A second pull request for v4.6 with a few fixesi before -rc1. The new
features for abx80x actually make the RTC behave correctly.
Drivers:
- abx80x: handle both XT and RC oscillators, XT failure bit and
autocalibration
- m41t80: avoid out of range year values
- rv8803: workaround an i2c HW issue"
* tag 'rtc-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: abx80x: handle the oscillator failure bit
rtc: abx80x: handle autocalibration
rtc: rv8803: workaround i2c HW issue
rtc: mcp795: add devicetree support
rtc: asm9260: remove incorrect __init/__exit annotations
rtc: m41t80: avoid out of range year values
rtc: s3c: Don't print an error on probe deferral
rtc: rv3029: stop mentioning rv3029c2
|
|
Handle the Oscillator Failure ('OF') bit from Oscillator Status register
(0x1D). This bit is cleared on set_time function and is read each time the
date/time is read, but only in case of XT Oscillator selection.
In RC mode, this bit is always set.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The autocalibration is separated in two bits to set in Oscillator
Control register (0x1c) :
- OSEL bit to select the oscillator type (XT or RC).
- ACAL bit to select the autocalibration type.
These functionnalities are exported in sysfs entries : "oscillator"
and "autocalibration". Respectively, the values are "xtal" for XT
oscillator and "rc" for RC oscillator and 0 to disable the
autocalibration cycle, 512 for a 512 seconds autocalibration cycle
and 1024 for a cycle of 1024 seconds.
Examples :
Set to XT Oscillator
echo xtal > /sys/class/rtc/rtc0/device/oscillator
Activate an autocalibration every 512 seconds
echo 512 > /sys/class/rtc/rtc0/device/autocalibration
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The rv8803 has a 60µs window where it will not answer on the i2c bus.
It also means there will be no ack for the communication. Make sure
communication is tried multiple times when this happens (the i2c subsystem
mandates -ENXIO is that case but the number of retries is host specific).
The critical parts are the probe function and the alarm callback so make
sure we handle the failure there.
Cc: stable@vger.kernel.org # v4.4
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add device tree support to the rtc-mcp795 driver.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The probe and remove callbacks of the platform driver are marked __init
and __exit, respectively. However, this is not a correct way to annotate
them, as it will result in those sections to be discarded at link time
or after boot, while we can actually call them again based on manual
unbinding, or deferred probing.
Kbuild warns about the problem:
WARNING: drivers/rtc/rtc-asm9260.o(.data+0x0): Section mismatch in reference from the variable asm9260_rtc_driver to the function .init.text:asm9260_rtc_probe()
This removes the annotations, so we no longer branch into missing
code and avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 125e550fd257 ("rtc: add Alphascale asm9260 driver")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Avoid saving an out of range year value to the RTC. Reading that value
from the RTC again returns a totally wrong time value. For Example
$ timedatectl set-ntp no
$ timedatectl set-time "1990-01-01 12:12:00"
# Reboot
rtc-m41t80 0-0068: setting system clock to 2090-01-01 12:12:35 UTC (3786955955)
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The clock and source clock looked up by the driver may not be available
just because the clock controller driver was not probed yet so printing
an error in this case is not correct and only adds confusion to users.
However, knowing that a driver's probe was deferred may be useful so it
can be printed as a debug information.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
