| Age | Commit message (Collapse) | Author |
|---|
|
pcf2123 has an offset register, which can be used to make minor
adjustments to the clock rate to compensate for temperature or
a crystal that is not exactly right.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
clock offset may be set and read in decimal parts per billion
attribute is /sys/class/rtc/rtcN/offset
The attribute is only visible for rtcs that have set_offset implemented.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
A number of rtc devices, such as the NXP pcf2123 include a facility
to adjust the clock in order to compensate for temperature or a
crystal, capacitor, etc, that results in the rtc clock not running
at exactly 32.768 kHz.
Data sheets I have seen refer to this as a clock offset, and measure it
in parts per million, however they often reference ppm to 2 digits of
precision, which makes integer ppm less than ideal.
We use parts per billion, which more than covers the precision needed
and works nicely within 32 bits
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Fix a scheduling while atomic issue caused by rv8803_set_time()
holding a spinlock during the call to i2c_smbus_read_byte_data().
Signed-off-by: Oleksij Rempel <fixed-term.Oleksij.Rempel@de.bosch.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add support for RTC controller found on Alphascale asm9260
SoC.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
DS3231 has programmable square-wave output signal.
This enables to use this feature as a clock provider of
common clock framework.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
To make RTC block of MAX77686/MAX77802 as independent driver,
move the registration of i2c device, regmap for register access
and irq_chip for interrupt support inside the RTC driver.
Removed the same initialisation from MFD driver.
Having this change will allow to reuse this driver for different
PMIC/devices from Maxim Semiconductor if they kept same RTC IP on
different PMIC. Some of examples as PMIC MAX77620, MAX20024 where
same RTC IP used and hence driver for these chips will use this
driver only for RTC support.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Get rid of referring parent device info for register access
all the places by making regmap as part of max77686 rtc
device info. This will also remove the need of storing parent
device info in max77686 rtc device info as this is no more required.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
rtc_regmap should be used to access all RTC registers instead
of parent regmap regardless of what chip or property have it.
This makes the register access uniform and extendible for other
chips.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Fix following check patch error in rtc-max77686 driver:
- Alignment should match open parenthesis.
- braces {} should be used on all arms of this statement.
- Prefer using the BIT macro
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
At the moment the "sun6i" RTC drivers depends on having two specific
SoC families selected.
The Allwinner A64 SoC has the same RTC, so extend the Kconfig option
to allow inclusion of the driver for all Allwinner SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The RX6110 comes in two different variants: SPI and I2C.
This driver only supports the SPI variant.
If the need ever arises to also support the I2C variant, this driver
could easily be refactored to support both cases.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
pcf2123 data sheet recommends a software reset when the chip
is first powered on. This change avoids resetting the chip
every time the driver is loaded, which has some negative effects.
There are several registers including a clock rate adjustment that really
should survive a reload of the driver (or reboot).
In addition, stopping and restarting the clock to verify the chip is
there is not a good thing once the time is set.
According to the data sheet, the seconds register has a 1 in
the high bit when the voltage has gotten low. We check for this
condition, as well as whether the time retrieved from the chip is
valid. We reset the rtc only if the time is not reliable and valid.
This is sufficient for checking for the presence of the chip,
as either all zeros or all 0xff will result in an invalid time/date
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Refactor chip reset items into its own function, isolating it from
the rest of the device probe.
Subsequent commits will avoid calling this code.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add new functions pcf2123_write(), and pcf2123_write_reg().
Use named defines for the values being written.
This improves modularity and readability, and reduces lines of code.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Put read operations into a function.
This improves modularity and readability.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add defines for all 16 registers in the pcf2123.
Add defines for useful bits from several registers
I've tried to document all the registers, and
as best as possible, all the special bits they employ
Use BIT() wherever possible in the bit definitions
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
DS3231 has the temperature registers with a resolution of 0.25
degree celsius. This enables to get the value through hwmon.
# cat /sys/class/i2c-adapter/i2c-2/2-0068/hwmon/hwmon0/temp1_input
21000
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
For RTC chips with no IRQ directly connected to the SoC, the RTC chip
can be forced as a wakeup source by stating that explicitly in
the device's .dts file using the "wakeup-source" boolean property.
This will guarantee the 'wakealarm' sysfs entry is available on the
device, if supported by the RTC.
With these changes to the driver rtc-ds1307 and the necessary entries
in the .dts file, I get an working ds1337 RTC on the Witty Pi extension
board by UUGear for the Raspberry Pi.
An example for the entry in the .dts file:
rtc: ds1337@68 {
compatible = "dallas,ds1337";
reg = <0x68>;
wakeup-source;
If the "wakeup-source" property is set, do not request an IRQ.
Set also UIE mode to unsupported, to get a working 'hwclock' binary.
Signed-off-by: Michael Lange <linuxstuff@milaw.biz>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The mt6397 RTC driver can be built either when the MFD_MT6397 driver
is enabled (which selects IRQ_DOMAIN), or when compile testing.
The latter however fails without IRQ domains:
drivers/rtc/rtc-mt6397.c: In function 'mtk_rtc_probe':
drivers/rtc/rtc-mt6397.c:326:13: error: implicit declaration of function 'irq_create_mapping' [-Werror=implicit-function-declaration]
rtc->irq = irq_create_mapping(mt6397_chip->irq_domain, res->start);
This adds an explicit dependency for the COMPILE_TEST case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The rv8803 has its own driver that should be used. Remove its id from
the rx8025 driver.
Fixes: b1f9d790b59dc04f8813a49a92ddd8651770ffee
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
For better readability, use to_spi_device() and kobj_to_dev() instead
of container_of().
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Cleanup of entire driver of its dmesg output:
1. Remove printing of the function name, because printing device name is
sufficient. This also makes the dev_err()-like functions more compact
and readable (not need of line break).
2. Lower from info to debug printing of each RTC interrupt (no need to
make noise on each alarm).
3. Remove dev_info() at beginning of probe because a message is already
always printed by either probe failure or from registering the RTC
device as /dev/rtcX.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The max77686 RTC driver now supports the max77802 RTC as
well so there's no need to have a separate driver anymore.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The regmap_irq_get_virq() can return 0 or -EINVAL in error conditions
but driver checked only for value of 0.
This could lead to a cast of -EINVAL to an unsigned int used as a
interrupt number for devm_request_threaded_irq(). Although this is not
yet fatal (devm_request_threaded_irq() will just fail with -EINVAL) but
might be a misleading when diagnosing errors.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 6f1c1e71d933 ("mfd: max77686: Convert to use regmap_irq")
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The max77686 RTC only supports a range of 99 years so instead of using
year 1900 as the base, the year 2000 is used. This means that 1900 to
1999 are unsupported years.
The driver was printing a warning for those values but was returning a
error so for consistency, print an error message instead and don't say
that a year 2000 is assumed, since the year is not set.
Also, it is better to use dev_* log functions instead of pr_* to print
information about the device in the kernel log in a standardized way.
This also allows to remove the local pr_fmt() defined macro.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The MAX77686 and MAX77802 RTC IP blocks are very similar with only
these differences:
0) The RTC registers layout and addresses are different.
1) The MAX77686 use 1 bit of the sec/min/hour/etc registers as the
alarm enable while MAX77802 has a separate register for that.
2) The MAX77686 RTCYEAR register valid values range is 0..99 while
for MAX77802 is 0..199.
3) The MAX77686 has a separate I2C address for the RTC registers
while the MAX77802 uses the same I2C address as the PMIC regs.
5) The minimum delay before a RTC update (16 msecs vs 200 usecs).
There are separate drivers for MAX77686 and MAX77802 RTC IP blocks
but the differences are not that big so the driver can be extended
to support both instead of duplicating a lot of code in 2 drivers.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The max77686 driver is generic enough that can be used for other
Maxim RTC IP blocks but these might not have the same registers
layout so instead of accessing the registers directly, add a map
to translate offsets to the real registers addresses for each IP.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The driver has some hard-coded values such as the minimum delay needed
before a RTC update or the mask used for the sec/min/hour/etc registers.
Use a data structure that contains these values and pass as driver data
using the platform device ID table for each device.
This allows to make the driver's ops callbacks more generic so other RTC
that are similar but don't have the same values can also be supported.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Documentation/timers/timers-howto.txt suggest to use usleep_range()
instead of msleep() for small msec (1ms - 20ms) since msleep() will
often sleep for 20ms for any value in that range.
This is fine in this case since 16ms is the _minimum_ delay required
by max77686 for an RTC update but by using usleep_range() instead of
msleep(), the driver can support other RTC IP blocks with a shorter
minimum delay (i.e: in the range of usecs instead of msecs).
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
It is better to use the ARRAY_SIZE() macro instead of the array length
to avoid bugs if the array is later changed and the length not updated.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The function is always returning zero even in case of failures since
the ret value was not propagated to the callers. Fix the error path.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Core:
- fix module reference count in rtc-proc
- Replace simple_strtoul by kstrtoul
New driver:
- Epson RX8010SJ
Subsystem wide cleanups:
- use %ph for short hex dumps
- constify *_chip_ops structures
Drivers:
- abx80x: Microcrystal rv1805 support, alarm support
- cmos: prevent kernel warning on IRQ flags mismatch
- s5m: various cleanups
- rv8803: rx8900 compatibility, small error path fix
- sunxi: various cleanups
- lpc32xx: remove irq > NR_IRQS check from probe()
- imxdi: fix spelling mistake in warning message
- ds1685: don't try to micromanage sysfs output size
- da9063: avoid writing undefined data to rtc
- gemini: Remove unnecessary platform_set_drvdata()
- efi: add efi_procfs in efi_rtc_ops
- pcf8523: refuse to write dates later than 2099"
* tag 'rtc-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (24 commits)
rtc: cmos: prevent kernel warning on IRQ flags mismatch
rtc: rtc-ds2404: constify ds2404_chip_ops structures
rtc: s5m: Make register configuration per S2MPS device to remove exceptions
rtc: s5m: Add separate field for storing auto-cleared mask in register config
rtc: s5m: Cleanup by removing useless 'rtc' prefix from fields
rtc: Replace simple_strtoul by kstrtoul
rtc: abx80x: add alarm support
rtc: abx80x: Add Microcrystal rv1805 support
rtc: v3020: constify v3020_chip_ops structures
rtc: rv8803: Extend compatibility with the rx8900
rtc: rv8803: fix handling return value of i2c_smbus_read_byte_data
rtc: Add Epson RX8010SJ RTC driver
rtc: lpc32xx: remove irq > NR_IRQS check from probe()
rtc: imxdi: fix spelling mistake in warning message
rtc: ds1685: don't try to micromanage sysfs output size
rtc: use %ph for short hex dumps
rtc: da9063: avoid writing undefined data to rtc
rtc: sunxi: use of_device_get_match_data
rtc: sunxi: constify the data_year_param structure
rtc: sunxi: fix signedness issues
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- Add support for s2mps15; sec-core
- Add support for Lewisburg; lpc_ich
- Add support for cs47l24 and wm1831; arizona
New Functionality:
- Allow user to select syscon register width; syscon
Fix-ups:
- Lots of Checkpatch fixes
- Rename -pmic/-regulator; s2mps11
- Build driver components into a single module; wm8994-*
- Better handing of IRQ during suspend/resume; as3722
- Constify things; da903x
- Remove unused code; ab8500-core
- Improve error handing; qcom_rpm
- Simplify code: wm831x-otp, sta2x11-mfd
- Improve locking; cros_ec_spi
- Fix incorrect DT binding filename reference; arizona, palmas,
snps-dwapb-gpio, wm8994
Bug Fixes:
- Fix broken SYSFS 'show ID' call; wm831x-otp
- Protect reads from non-existent registers; qcom-spmi-pmic
- Repair build warnings; as3722
- Fix IRQ request ordering; arizona-irq
- Ensure return value is boolean; ucb1x00-core, tps65010, tc6393xb,
htc-egpio, dm355evm_msp, asic3"
* tag 'mfd-for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (58 commits)
mfd: davinci_voicecodec: Remove pointless 'out of memory' error message
mfd: da9052-irq: Fix trivial 'space before comma' error
mfd: da9052-i2c: Fix tabbing/whitespace issue
mfd: da903x: Fix white space and split string issues
mfd: cs5535-mfd: Add missing line spacing and make local array static
mfd: cros_ec_spi: Repair comparison ordering issue
mfd: cros_ec_i2c: Fix trivial 'tabs before spaces' whitespace issue.
mfd: asic3: Fix a plethora of Checkpatch errors and warnings
mfd: as3711: Repair OOM and 'line over 80 chars' formatting warnings
mfd: arizona-i2c: Add blank line formatting after declaration
mfd: arizona-core: msleep() is unreliable for anything <20ms use usleep_range() instead
mfd: adp5520: Some trivial 'no space before tab' fixes
mfd: ab8500-sysctrl: Fix Constify, printk => pr_info and formatting issues
mfd: ab8500-gpadc: Squash a whole bunch of Checkpatch warnings and one error
mfd: ab8500-debugfs: Clean-up non-conforming commenting and print formatting
mfd: ab8500-core: Fix many warnings reported by Checkpatch
mfd: ab2100-otp: Remove pointless 'out of memory' error message
mfd: ab3100-core.c: Fix multiple warnings reported by Checkpatch
mfd: aat2870-core: Remove unnecessary 'out of memory' message
mfd: 88pm860x-core: Fix commenting and declaration spacing
...
|
|
The Microsoft Surface 3 tablet shares interrupt line between RTC and one of SPI
controllers. However, the rtc_cmos driver doesn't allow shared interrupts and
user sees the following warning
genirq: Flags mismatch irq 8. 00000080 (8086228E:02) vs. 00000000 (rtc0)
...
[<ffffffffa004eb01>] pxa2xx_spi_probe+0x151/0x600 [spi_pxa2xx_platform]
Allow RTC driver to use shared interrupts.
Seems we are on the safe side to do just this simple change since
cmos_interrupt() handler checks for the actual hardware status anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The ds2404_chip_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Before updating time and alarm the driver must set appropriate mask in
UDR register. For that purpose the driver uses common register
configuration and a lot of exceptions per device in the code. The
exceptions are not obvious, for example except the change in the logic
sometimes the fields are swapped (WUDR and AUDR between S2MPS14 and
S2MPS15). This leads to quite complicated code.
Try to make it more obvious by:
1. Documenting the UDR masks for devices and operations.
2. Adding fields in register configuration structure for each operation
(read time, write time and alarm).
3. Splitting the configuration per S2MPS13, S2MPS14 and S2MPS15 thus
removing exceptions for them.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Some devices from S2M/S5M family use different register update masks for
different operations (alarm and register update). Now the driver uses
common register configuration and a lot of exceptions per device in code.
Before eliminating the exceptions and using specific register
configuration for given device, make the auto-cleared mask a separate
field. This is merely a refactoring.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Remove the 'rtc' prefix from some of the fields in struct
s5m_rtc_reg_config because it is obvious - this is a RTC driver. No
functional changes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The simple_strtoul function is obsolete.
This patch replace it by kstrtoul.
Since kstrtoul is more strict, it permits to filter some invalid input that
simple_strtoul accept. For example:
echo '1022xxx' > /sys/devices/pnp0/00:03/rtc/rtc0/max_user_freq
cat /sys/devices/pnp0/00:03/rtc/rtc0/max_user_freq
1022
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add alarm support to the abx80x driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Microcrystal RV-1805 is compatible with Abracon 1805.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The v3020_chip_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The Seiko Epson's RTC RX8900 layout register is compatible with the
RV8803. So let's add its ID in order to reuse the same driver.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The function can return negative values, so its result should
be assigned to signed variable.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
This driver supports the following functions:
- reading and setting time
- alarms when connected to an IRQ
- reading and clearing the voltage low flags
Datasheet:
http://www.epsondevice.com/docs/qd/en/DownloadServlet?id=ID000956
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
If the driver is used on an ARM platform with SPARSE_IRQ defined,
semantics of NR_IRQS is different (minimal value of virtual irqs)
and by default it is set to 16, see arch/arm/include/asm/irq.h.
This value may be less than the actual number of virtual irqs, which
may break the driver initialization. The check removal allows to use
the driver on such a platform, and, if irq controller driver works
correctly, the check is not needed on legacy platforms.
Fixes a runtime problem:
rtc-lpc32xx 40024000.rtc: Can't get interrupt resource
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Minor issue, fix spelling mistake, happend -> happened
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
...and don't do it wrong.
"not ok or N/A" has length 13. Add the trailing newline, and the
snprintf return value will be 14. However, we lied to snprintf and
told it that only 13 bytes were available. Hence snprintf has only
written "not ok or N/" and a trailing '\0' to the buffer. Next we
continue lying, this time to the upper sysfs layer, claiming that we
wrote 14 meaningful bytes to the buffer. That'll make the upper layer
copy "not ok or N/" plus two nul bytes to user space (one nul byte
from snprintf, the other since sysfs takes care to clear the buffer
before giving it to the ->show method).
In the other cases, the claimed buffer size is closer to sufficient,
but we'll still get a nul byte instead of a newline written to user
space. There's absolutely no reason to try to predict the output
size, and there's plenty of room in the buffer, so just use sprintf.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
