| Age | Commit message (Collapse) | Author |
|---|
|
As said in the SAMA5D2 datasheet, "Prior to instructing the device
to enter ULP mode 1, ... and the internal sources of wake-up must
be cleared."
This patch is to clear the RTC alarm status flag prior to suspending
to avoid the erroneous wake-up activity, as it is often used as
the wake-up source for the ULP mode 1.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Commit dca1a4b5ff6e ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.
Get and use the slow clock as it is necessary for the at91rm9200 rtc.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Sort included headers alphabetically.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Change the __raw IO calls to readl/write_relaxed which makes the driver
endian agnostic to run properly on big endian systems.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Andrew Victor <linux@maxim.org.za>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is a typo here so we deadlock.
Fixes: dd1f1f391dd7 ('rtc: at91rm9200: rework wakeup and interrupt handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: David Dueck <davidcdueck@googlemail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The IRQ line used by the RTC device is usually shared with the system
timer (PIT) on at91 platforms.
Since timers are registering their handlers with IRQF_NO_SUSPEND, we
should expect being called in suspended state, and properly wake the
system up when this is the case.
Set IRQF_COND_SUSPEND flag when registering the IRQ handler to inform
irq core that it can safely be called while the system is suspended.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The rtc user must wait at least 1 sec between each time/calandar update
(see atmel's datasheet chapter "Updating Time/Calendar").
Use the 1Hz interrupt to update the at91_rtc_upd_rdy flag and wait for
the at91_rtc_wait_upd_rdy event if the rtc is not ready.
This patch fixes a deadlock in an uninterruptible wait when the RTC is
updated more than once every second. AFAICT the bug is here from the
beginning, but I think we should at least backport this fix to 3.10 and
the following longterm and stable releases.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Bryan Evenson <bevenson@melinkcorp.com>
Tested-by: Bryan Evenson <bevenson@melinkcorp.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update month and day of month to the alarm month/day instead of current
day/month when setting the RTC alarm mask.
Signed-off-by: Linus Pizunski <linus@narrativeteam.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make sure RTC-interrupts are disabled at shutdown.
As the RTC is generally powered by backup power (VDDBU), its interrupts
are not disabled on wake-up, user, watchdog or software reset. This
could cause troubles on other systems (e.g. older kernels) if an
interrupt occurs before a handler has been installed at next boot.
Let us be well-behaved and disable them on clean shutdowns at least (as
do the RTT-based rtc-at91sam9 driver).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
devm_* APIs are device managed and make code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The driver core clears the driver data to NULL after device_release or
on probe failure, since commit 0998d063100 ("device-core: Ensure drvdata
= NULL when no driver is bound"). Thus, it is not needed to manually
clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Silences the following checkpatch warning:
WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for the at91sam9x5-family which must use the shadow
interrupt mask due to a hardware issue (causing RTC_IMR to always be
zero).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add shadow interrupt-mask register which can be used on SoCs where the
actual hardware register is broken.
Note that some care needs to be taken to make sure the shadow mask
corresponds to the actual hardware state. The added overhead is not an
issue for the non-broken SoCs due to the relatively infrequent
interrupt-mask updates. We do, however, only use the shadow mask value
as a fall-back when it actually needed as there is still a theoretical
possibility that the mask is incorrect (see the code for details).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add accessors for the interrupt register.
This will allow us to easily add a shadow interrupt-mask register to use
on SoCs where the interrupt-mask register cannot be used.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add configuration support which can be used to implement SoC-specific
workarounds for broken hardware.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The members of Atmel's at91sam9x5 family (9x5) have a broken RTC
interrupt mask register (AT91_RTC_IMR). It does not reflect enabled
interrupts but instead always returns zero.
The kernel's rtc-at91rm9200 driver handles the RTC for the 9x5 family.
Currently when the date/time is set, an interrupt is generated and this
driver neglects to handle the interrupt. The kernel complains about the
un-handled interrupt and disables it henceforth. This not only breaks
the RTC function, but since that interrupt is shared (Atmel's SYS
interrupt) then other things break as well (e.g. the debug port no
longer accepts characters).
Tested on the at91sam9g25. Bug confirmed by Atmel.
This patch (of 5):
Add missing match-table compile guard.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add missing iounmap to probe error path and remove.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch to using the SIMPLE_DEV_PM_OPS macro to declare the driver's
pm_ops. It reduces code size.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use module_platform_driver_probe() macro which makes the code smaller and
simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 0ef1594c017521ea89278e80fe3f80dafb17abde.
This patch introduced a few races which cannot be easily fixed with a
small follow-up patch. Furthermore, the SoC with the broken hardware
register, which this patch intended to add support for, can only be used
with device trees, which this driver currently does not support.
[ Here is the discussion that led to this "revert" patch:
https://lkml.org/lkml/2013/4/3/176 ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On some revisions of AT91 SoCs, the RTC IMR register is not working.
Instead of elaborating a workaround for that specific SoC or IP version,
we simply use a software variable to store the Interrupt Mask Register
and modify it for each enabling/disabling of an interrupt. The overhead
of this is negligible anyway.
The interrupt mask register (IMR) for the RTC is broken on the AT91SAM9x5
sub-family of SoCs (good overview of the members here:
http://www.eewiki.net/display/linuxonarm/AT91SAM9x5 ). The "user visible
effect" is the RTC doesn't work.
That sub-family is less than two years old and only has devicetree (DT)
support and came online circa lk 3.7 . The dust is yet to settle on the
DT stuff at least for AT91 SoCs (translation: lots of stuff is still
broken, so much that it is hard to know where to start).
The fix in the patch is pretty simple: just shadow the silicon IMR
register with a variable in the driver. Some older SoCs (pre-DT) use the
the rtc-at91rm9200 driver (e.g. obviously the AT91RM9200) and they should
not be impacted by the change. There shouldn't be a large volume of
interrupts associated with a RTC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
MULTI_IRQ_HANDLER and SPARSE_IRQ are now required everywhere because
mach/irqs.h and mach/entry-macros.S are gone but the symbols are
only selected for AT91SAM9, not for the NOMMU parts.
A few files now need to include linux/io.h directly, which used to
be included through other headers that have changed.
The new at91_aic_irq_priorities variable is only used with CONFIG_OF
enabled and should not be visible otherwise.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
switch the rtc drivers to resource and pass it via platform_device
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
With the generic RTC rework, the UIE mode irqs are handled
in the generic layer, and only hardware specific ioctls
get passed down to the rtc driver layer.
So this patch removes the UIE mode ioctl handling in the rtc
driver layer, which never get used.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
CC: rtc-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Some rtc drivers use the ioctl method instead of the alarm_irq_enable
method for enabling alarm interupts. With the new virtualized RTC
rework, its important for drivers to use the alarm_irq_enable instead.
This patch converts the drivers that use the AIE ioctl method to
use the alarm_irq_enable method. Other ioctl cmds are left untouched.
I have not been able to test or even compile most of these drivers.
Any help to make sure this change is correct would be appreciated!
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Reported-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Tested-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Fix two new-ish runtime warnings in the at91rm9200 (etc) RTC:
Platform driver 'at91_rtc' needs updating - please use dev_pm_ops
... by just switching
IRQ 1/at91_rtc: IRQF_DISABLED is not guaranteed on shared IRQs
... no longer needed now that rtc_update_irq() changed
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change drivers/rtc/ to use the new bcd2bin/bin2bcd functions instead of
the obsolete BCD_TO_BIN/BIN_TO_BCD/BCD2BIN/BIN2BCD macros.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The non-functional periodic IRQ support was previously removed from the
AT91RM9200 RTC driver. Remove the remaining AT91_RTC_FREQ definition.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Cc: David Brownell: <david-b@pacbell.net>
Cc: Alessandro Zummo: <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This fixes kernel http://bugzilla.kernel.org/show_bug.cgi?id=11112 (bogus
RTC update IRQs reported) for rtc-at91rm9200 by scrubbing old IRQ status
before enabling IRQs.
It also removes nonfunctional periodic IRQ support from this driver;
only update IRQs are reported, or provided by the hardware.
I suspect some other RTCs probably have versions of #11112; it's easy to
overlook, since most non-RTC drivers don't care about spurious IRQs:
they're not reported to userspace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Report-by: W Unruh <unruh@physics.ubc.ca>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On ARM, asm/rtc.h only contains definitions for the predecessor to
the RTC class support. RTC class drivers should not be including
this include.
Build tested on at91sam9rl and s3c2410 configurations.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
asm/mach/time.h is the ARM header file for setting up kernel ticker
timekeeping (be that the old jiffy interrupt or the new clocksource.)
RTC drivers have no business using this header file, and in fact do
not require it.
Build tested on at91sam9rl, omap and s3c2410 configurations.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable RTC
platform drivers, to re-enable module auto loading.
[dbrownell@users.sourceforge.net: more drivers, minor fix]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
RTC class suspend/resume support, re-initializing the system clock on resume
from the clock used to initialize it at boot time.
- The reinit-on-resume is hooked to the existing RTC_HCTOSYS config
option, on the grounds that a clock good enough for init must also
be good enough for re-init.
- Inlining a version of the code used by ARM, to save and restore the
delta between a selected RTC and the current system wall-clock time.
- Removes calls to that ARM code from AT91, OMAP1, and S3C RTCs. This
means that systems using those RTCs across suspend/resume will likely
want to change their kernel configs to enable RTC_HCTOSYS.
If HCTOSYS isn't using a second RTC (with battery?), this changes the
system's initial date from Jan 1970 to the epoch this hardware uses:
1998 for AT91, 2000 for OMAP1 (assuming no split power mode), etc.
This goes on top of the patch series removing "struct class_device" usage
from the RTC framework. That's all needed for class suspend()/resume().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-By: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch removes class_device from the programming interface that the RTC
framework exposes to the rest of the kernel. Now an rtc_device is passed,
which is more type-safe and streamlines all the relevant code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-By: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Various bug fixes to the at91rm9200 RTC:
- alarm: setalarm() should pay attention to the "enabled" flag
- init: cleaner handling of the wakeup flags, which cpu init should
really have set up. Doing it here is just a workaround.
- linkage: since the at91_rtc driver probe() routine is in the init
section, it should use platform_driver_probe() instead of leaving
that pointer around in the driver struct after init section removal.
- linkage: likewise, remove() belongs in the exit section.
Among other things, the init and alarm changes ensure that this driver
handles the new sysfs "wakealarm" attribute properly.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The at91rm9200 RTC driver needs some assistance to build, because of recent
header file rearrangement.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix a glitch in the procfs dumping of whether the alarm IRQ is enabled: use
the traditional name (from drivers/char/rtc.c and many other places) of
"alarm_IRQ", not "alrm_wakeup" (which didn't even match the efirtc code, which
originated that reporting API).
Also, update a few of the RTC drivers to stop providing that duplicate status,
and/or to expose it properly when reporting the alarm state. We really don't
want every RTC driver doing their own thing here...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The new Atmel AT91SAM9261 and AT91SAM9260 processors do not have the
internal RTC peripheral. This RTC driver is therefore
AT91RM9200-specific.
This patch renames rtc-at91.c to rtc-at91rm9200.c, and changes the name
of the configuration option.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
