| Age | Commit message (Collapse) | Author |
|---|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"cros-ec:
- Error code cleanup across cros-ec by Guenter
- Remove cros_ec_cmd_xfer in favor of cros_ec_cmd_xfer_status
cros_ec_typec:
- Landed initial USB4 support in typec connector class driver for
cros_ec
- Role switch bugfix on disconnect, and reordering configuration
steps
cros_ec_lightbar:
- Fix buffer outsize and result for get_lightbar_version
misc:
- Remove config MFD_CROS_EC, now that transition from MFD is complete
- Enable KEY_LEFTMETA in new location on arm based cros-ec-keyboard
keymap"
* tag 'tag-chrome-platform-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
ARM: dts: cros-ec-keyboard: Add alternate keymap for KEY_LEFTMETA
platform/chrome: Use kobj_to_dev() instead of container_of()
platform/chrome: cros_ec_proto: Drop cros_ec_cmd_xfer()
platform/chrome: cros_ec_proto: Update cros_ec_cmd_xfer() call-sites
platform/chrome: Kconfig: Remove the transitional MFD_CROS_EC config
platform/chrome: cros_ec_lightbar: Reduce ligthbar get version command
platform/chrome: cros_ec_trace: Add fields to command traces
platform/chrome: cros_ec_typec: Re-order connector configuration steps
platform/chrome: cros_ec_typec: Avoid setting usb role twice during disconnect
platform/chrome: cros_ec_typec: Send enum values to usb_role_switch_set_role()
platform/chrome: cros_ec_typec: USB4 support
pwm: cros-ec: Simplify EC error handling
platform/chrome: cros_ec_proto: Convert EC error codes to Linux error codes
platform/input: cros_ec: Replace -ENOTSUPP with -ENOPROTOOPT
pwm: cros-ec: Accept more error codes from cros_ec_cmd_xfer_status
platform/chrome: cros_ec_sysfs: Report range of error codes from EC
cros_ec_lightbar: Accept more error codes from cros_ec_cmd_xfer_status
iio: cros_ec: Accept -EOPNOTSUPP as 'not supported' error code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This release cycle's updates are mostly cleanup and some minor fixes"
* tag 'pwm/for-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
dt-bindings: pwm: renesas,pwm-rcar: Add r8a7742 support
dt-bindings: pwm: renesas,tpu-pwm: Document r8a7742 support
pwm: Allow store 64-bit duty cycle from sysfs interface
pwm: img: Fix null pointer access in probe
pwm: pca9685: Disable unused alternative addresses
pwm: pca9685: Use BIT() macro instead of shift
pwm: pca9685: Make comments more consistent
pwm: sun4i: Simplify with dev_err_probe()
pwm: sprd: Simplify with dev_err_probe()
pwm: sifive: Simplify with dev_err_probe()
pwm: rockchip: Simplify with dev_err_probe()
pwm: jz4740: Simplify with dev_err_probe()
pwm: bcm2835: Simplify with dev_err_probe()
pwm: Convert to use DEFINE_SEQ_ATTRIBUTE macro
pwm: rockchip: Keep enabled PWMs running while probing
dt-bindings: pwm: renesas,pwm-rcar: Add r8a774e1 support
|
|
Pull drm updates from Dave Airlie:
"Not a major amount of change, the i915 trees got split into display
and gt trees to better facilitate higher level review, and there's a
major refactoring of i915 GEM locking to use more core kernel concepts
(like ww-mutexes). msm gets per-process pagetables, older AMD SI cards
get DC support, nouveau got a bump in displayport support with common
code extraction from i915.
Outside of drm this contains a couple of patches for hexint
moduleparams which you've acked, and a virtio common code tree that
you should also get via it's regular path.
New driver:
- Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config"
* tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm: (1494 commits)
drm/ingenic: Fix bad revert
drm/amdgpu: Fix invalid number of character '{' in amdgpu_acpi_init
drm/amdgpu: Remove warning for virtual_display
drm/amdgpu: kfd_initialized can be static
drm/amd/pm: setup APU dpm clock table in SMU HW initialization
drm/amdgpu: prevent spurious warning
drm/amdgpu/swsmu: fix ARC build errors
drm/amd/display: Fix OPTC_DATA_FORMAT programming
drm/amd/display: Don't allow pstate if no support in blank
drm/panfrost: increase readl_relaxed_poll_timeout values
MAINTAINERS: Update entry for st7703 driver after the rename
Revert "gpu/drm: ingenic: Add option to mmap GEM buffers cached"
drm/amd/display: HDMI remote sink need mode validation for Linux
drm/amd/display: Change to correct unit on audio rate
drm/amd/display: Avoid set zero in the requested clk
drm/amdgpu: align frag_end to covered address space
drm/amdgpu: fix NULL pointer dereference for Renoir
drm/vmwgfx: fix regression in thp code due to ttm init refactor.
drm/amdgpu/swsmu: add interrupt work handler for smu11 parts
drm/amdgpu/swsmu: add interrupt work function
...
|
|
PWM core was converted to u64 by the commit a9d887dc1c60 ("pwm: Convert
period and duty cycle to u64") but did not change the duty_cycle_store()
so it will error out if trying to pass a numeric string bigger than
2^32-1.
Fix this by using u64 and kstrtou64() in duty_cycle_store().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Guru Das Srinagesh <gurus@codeaurora.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
dev_get_drvdata() is called in img_pwm_runtime_resume() before the
driver data is set.
When pm_runtime_enabled() returns false in img_pwm_probe() it calls
img_pwm_runtime_resume() which results in a null pointer access.
This patch fixes the problem by setting the driver data earlier in the
img_pwm_probe() function.
This crash was seen when booting the Imagination Technologies Creator
Ci40 (Marduk) with kernel 5.4 in OpenWrt.
Fixes: e690ae526216 ("pwm: img: Add runtime PM")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PCA9685 supports listening to 1 or more alternative I2C chip addresses
for some special features that this driver does not support.
By default the LED ALLCALL address is active (default 0x70), which causes
this chip to respond to address 0x70 in addition to its main address
(0x41). This is not desireable if there is another device on the same bus
that uses this address (like a TMP103 for example).
Since this feature is not supported by this driver, it is best to disable
these addresses in the chip to avoid unsuspected bus collisions.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Make all explanatory comments start with an uppercase char.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Use DEFINE_SEQ_ATTRIBUTE macro to simplify the code.
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Following commit cfc4c189bc70 ("pwm: Read initial hardware state at
request time") the Rockchip PWM driver can no longer assume a device's
pwm_state structure has been populated after a call to pwmchip_add().
Consequently, the test in rockchip_pwm_probe() intended to prevent the
driver from stopping PWM devices already enabled by the bootloader no
longer functions reliably and this can lead to the kernel hanging
during startup, particularly on devices like the Pinebook Pro that use
a PWM-controlled backlight for their display.
Avoid this by querying the device directly at probe time to determine
whether or not it is enabled.
Fixes: cfc4c189bc70 ("pwm: Read initial hardware state at request time")
Signed-off-by: Simon South <simon@simonsouth.net>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add support for the PWM controller of the sl28cpld board management
controller. This is part of a multi-function device driver.
The controller has one PWM channel and can just generate four distinct
frequencies.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Sync drm-intel-gt-next here so we can have an unified fixes flow.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Implement the pwm_ops.get_state() method to complete the support for the
new atomic PWM API.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-14-hdegoede@redhat.com
|
|
Replace the enable, disable and config pwm_ops with an apply op,
to support the new atomic PWM API.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-13-hdegoede@redhat.com
|
|
The pwm-crc code is using 2 different enable bits:
1. bit 7 of the PWM0_CLK_DIV (PWM_OUTPUT_ENABLE)
2. bit 0 of the BACKLIGHT_EN register
So far we've kept the PWM_OUTPUT_ENABLE bit set when disabling the PWM,
this commit makes crc_pwm_disable() clear it on disable and makes
crc_pwm_enable() set it again on re-enable.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-12-hdegoede@redhat.com
|
|
The pwm-crc code is using 2 different enable bits:
1. bit 7 of the PWM0_CLK_DIV (PWM_OUTPUT_ENABLE)
2. bit 0 of the BACKLIGHT_EN register
The BACKLIGHT_EN register at address 0x51 really controls a separate
output-only GPIO which is earmarked to be used as output connected to the
backlight-enable pin for LCD panels, this GPO is part of the PMIC's
"Display Panel Control Block." . This pin should probably be moved over
to a GPIO provider driver (and consumers modified accordingly), but that
is something for an(other) patch.
Enabling / disabling the actual PWM output is controlled by the
PWM_OUTPUT_ENABLE bit of the PWM0_CLK_DIV register.
As the comment in the old code already indicates we must disable the PWM
before we can change the clock divider. But the crc_pwm_disable() and
crc_pwm_enable() calls the old code make for this only change the
BACKLIGHT_EN register; and the value of that register does not matter for
changing the period / the divider. What does matter is that the
PWM_OUTPUT_ENABLE bit must be cleared before a new value can be written.
This commit modifies crc_pwm_config() to clear PWM_OUTPUT_ENABLE instead
when changing the period, so that period changes actually work.
Note this fix will cause a significant behavior change on some devices
using the CRC PWM output to drive their backlight. Before the PWM would
always run with the output frequency configured by the BIOS at boot, now
the period time specified by the i915 driver will actually be honored.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-11-hdegoede@redhat.com
|
|
The CRC PWM controller has a clock-divider which divides the clock with
a value between 1-128. But as can seen from the PWM_DIV_CLK_xxx
defines, this range maps to a register value of 0-127.
So after calculating the clock-divider we must subtract 1 to get the
register value, unless the requested frequency was so high that the
calculation has already resulted in a (rounded) divider value of 0.
Note that before this fix, setting a period of PWM_MAX_PERIOD_NS which
corresponds to the max. divider value of 128 could have resulted in a
bug where the code would use 128 as divider-register value which would
have resulted in an actual divider value of 0 (and the enable bit being
set). A rounding error stopped this bug from actually happen. This
same rounding error means that after the subtraction of 1 it is impossible
to set the divider to 128. Also bump PWM_MAX_PERIOD_NS by 1 ns to allow
setting a divider of 128 (register-value 127).
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-10-hdegoede@redhat.com
|
|
While looking into adding atomic-pwm support to the pwm-crc driver I
noticed something odd, there is a PWM_BASE_CLK define of 6 MHz and
there is a clock-divider which divides this with a value between 1-128,
and there are 256 duty-cycle steps.
The pwm-crc code before this commit assumed that a clock-divider
setting of 1 means that the PWM output is running at 6 MHZ, if that
is true, where do these 256 duty-cycle steps come from?
This would require an internal frequency of 256 * 6 MHz = 1.5 GHz, that
seems unlikely for a PMIC which is using a silicon process optimized for
power-switching transistors. It is way more likely that there is an 8
bit counter for the duty cycle which acts as an extra fixed divider
wrt the PWM output frequency.
The main user of the pwm-crc driver is the i915 GPU driver which uses it
for backlight control. Lets compare the PWM register values set by the
video-BIOS (the GOP), assuming the extra fixed divider is present versus
the PWM frequency specified in the Video-BIOS-Tables:
Device: PWM Hz set by BIOS PWM Hz specified in VBT
Asus T100TA 200 200
Asus T100HA 200 200
Lenovo Miix 2 8 23437 20000
Toshiba WT8-A 23437 20000
So as we can see if we assume the extra division by 256 then the register
values set by the GOP are an exact match for the VBT values, where as
otherwise the values would be of by a factor of 256.
This commit fixes the period / duty_cycle calculations to take the
extra division by 256 into account.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-9-hdegoede@redhat.com
|
|
PWM controller drivers should not restore the PWM state on resume. The
convention is that PWM consumers do this by calling pwm_apply_state(),
so that it can be done at the exact moment when the consumer needs
the state to be stored, avoiding e.g. backlight flickering.
The only in kernel consumers of the pwm-lpss code, the i915 driver
and the pwm-class sysfs interface code both correctly restore the
state on resume, so there is no need to do this in the pwm-lpss code.
More-over the removed resume handler is buggy, since it blindly
restores the ctrl-register contents without setting the update
bit, which is necessary to get the controller to actually use/apply
the restored base-unit and on-time-div values.
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-8-hdegoede@redhat.com
|
|
Before this commit pwm_lpss_apply() was assuming 2 pre-conditions
were met by the existing hardware state:
1. That the base-unit and on-time-div read back from the
control register are those actually in use, so that it
can skip setting the update bit if the read-back value
matches the desired values.
2. That the controller is enabled when the cached
pwm_state.enabled says that the controller is enabled.
As the long history of fixes for subtle (often suspend/resume)
lpss-pwm issues shows, these assumptions are not necessary
always true.
1. Specifically is not true on some (*) Cherry Trail devices
with a nasty GFX0._PS3 method which: a. saves the ctrl reg value.
b. sets the base-unit to 0 and writes the update bit to apply/commit
c. restores the original ctrl value without setting the update bit,
so that the 0 base-unit value is still in use.
2. Assumption 2. currently is true, but only because of the code which
saves/restores the state on suspend/resume. By convention restoring the
PWM state should be done by the PWM consumer and the presence of this
code in the pmw-lpss driver is a bug. Therefor the save/restore code will
be dropped in the next patch in this series, after which this assumption
also is no longer true.
This commit changes the pwm_lpss_apply() to not make any assumptions about
the state the hardware is in. Instead it makes pwm_lpss_apply() always
fully program the PWM controller, making it much less fragile.
*) Seen on the Acer One 10 S1003, Lenovo Ideapad Miix 310 and 320 models
and various Medion models.
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-7-hdegoede@redhat.com
|
|
In the not-enabled -> enabled path pwm_lpss_apply() needs to get a
runtime-pm reference; and then on any errors it needs to release it
again.
This leads to somewhat hard to read code. This commit introduces a new
pwm_lpss_prepare_enable() helper and moves all the steps necessary for
the not-enabled -> enabled transition there, so that we can error check
the entire transition in a single place and only have one pm_runtime_put()
on failure call site.
While working on this I noticed that the enabled -> enabled (update
settings) path was quite similar, so I've added an enable parameter to
the new pwm_lpss_prepare_enable() helper, which allows using it in that
path too.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-6-hdegoede@redhat.com
|
|
When the user requests a high enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value of 0.
But according to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency. Adding 0
to the counter is a no-op. The data-sheet even explicitly states that
writing 0 to the base_unit bits will result in the PWM outputting a
continuous 0 signal.
When the user requestes a low enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value
which is bigger then base_unit_range - 1. Currently the codes for this
deals with this by applying a mask:
base_unit &= (base_unit_range - 1);
But this means that we let the value overflow the range, we throw away the
higher bits and store whatever value is left in the lower bits into the
register leading to a random output frequency, rather then clamping the
output frequency to the highest frequency which the hardware can do.
This commit fixes both issues by clamping the base_unit value to be
between 1 and (base_unit_range - 1).
Fixes: 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-5-hdegoede@redhat.com
|
|
According to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency.
So assuming e.g. a 16 bit counter this means that if base_unit is set to 1,
after 65535 input clock-cycles the counter has been increased from 0 to
65535 and it will overflow on the next cycle, so it will overflow after
every 65536 clock cycles and thus the calculations done in
pwm_lpss_prepare() should use 65536 and not 65535.
This commit fixes this. Note this also aligns the calculations in
pwm_lpss_prepare() with those in pwm_lpss_get_state().
Note this effectively reverts commit 684309e5043e ("pwm: lpss: Avoid
potential overflow of base_unit"). The next patch in this series really
fixes the potential overflow of the base_unit value.
Fixes: 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-4-hdegoede@redhat.com
|
|
With enhanced error reporting from cros_ec_cmd_xfer_status() in place,
we can fully use it and no longer rely on EC error codes.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
|
|
Since commit c5cd2b47b203 ("platform/chrome: cros_ec_proto: Report command
not supported") we can no longer assume that cros_ec_cmd_xfer_status()
reports -EPROTO for all errors returned by the EC itself. A follow-up
patch will change cros_ec_cmd_xfer_status() to report additional errors
reported by the EC as distinguished Linux error codes.
Handle this change by no longer assuming that only -EPROTO is used
to report all errors returned by the EC itself. Instead, support both
the old and the new error codes.
Add a comment describing cros_ec_num_pwms() to explain its functionality.
Cc: Gwendal Grignou <gwendal@chromium.org>
Cc: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Cc: Prashant Malani <pmalani@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
|
|
The plat-samsung directory and mach-s5pv210 can be build
completely independently, so split the two Kconfig symbols
CONFIG_PLAT_SAMSUNG and CONFIG_ARCH_S5PV210.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-18-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some
types of hardware can generate the full range of signals that they're
capable of.
The remainder is mostly minor fixes and cleanups"
* tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: bcm-iproc: handle clk_get_rate() return
pwm: Replace HTTP links with HTTPS ones
pwm: omap-dmtimer: Repair pwm_omap_dmtimer_chip's broken kerneldoc header
pwm: mediatek: Provide missing kerneldoc description for 'soc' arg
pwm: bcm-kona: Remove impossible comparison when validating duty cycle
pwm: bcm-iproc: Remove impossible comparison when validating duty cycle
pwm: iqs620a: Use lowercase hexadecimal literals for consistency
pwm: Convert period and duty cycle to u64
clk: pwm: Use 64-bit division function
backlight: pwm_bl: Use 64-bit division function
pwm: sun4i: Use nsecs_to_jiffies to avoid a division
pwm: sifive: Use 64-bit division macro
pwm: iqs620a: Use 64-bit division
pwm: imx27: Use 64-bit division macro
pwm: imx-tpm: Use 64-bit division macro
pwm: clps711x: Use 64-bit division macro
hwmon: pwm-fan: Use 64-bit division macro
drm/i915: Use 64-bit division macro
|
|
Handle clk_get_rate() returning 0 to avoid possible division by zero.
Fixes: daa5abc41c80 ("pwm: Add support for Broadcom iProc PWM controller")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Argument descriptions must be prepended with a '@' to be understood
by the kerneldoc tooling/parsers/validators.
Fixes the following W=1 warning:
drivers/pwm/pwm-omap-dmtimer.c:70: warning: Function parameter or member 'dm_timer_pdev' not described in 'pwm_omap_dmtimer_chip'
Cc: Tony Lindgren <tony@atomide.com>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Grant Erickson <marathon96@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Kerneldoc syntax is used, but not complete.
Descriptions are required for all arguments.
Fixes the following W=1 build warning:
drivers/pwm/pwm-mediatek.c:57: warning: Function parameter or member 'soc' not described in 'pwm_mediatek_chip'
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Zhi Mao <zhi.mao@mediatek.com>
Cc: linux-pwm@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
'dc' here is an unsigned long, thus checking for <0 will always
evaluate to false.
Fixes the following W=1 warning:
drivers/pwm/pwm-bcm-kona.c:141:35: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-pwm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
'duty' here is an unsigned int, thus checking for <0 will always
evaluate to false.
Fixes the following W=1 warning:
drivers/pwm/pwm-bcm-iproc.c:147:12: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-pwm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The unicore32 port is removed from the kernel.
There is no point to keep stale PWM driver for this architecture.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
|
|
Other drivers use lowercase hexadecimal literals, so convert the IQS620a
driver to do the same for consistency.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Because period and duty cycle are defined as ints with units of
nanoseconds, the maximum time duration that can be set is limited to
~2.147 seconds. Change their definitions to u64 in the structs of the
PWM framework so that higher durations may be set.
Also use the right format specifiers in debug prints in both core.c,
pwm-stm32-lp.c as well as video/fbdev/ssd1307fb.c.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Since the PWM framework is switching struct pwm_state.period's datatype
to u64, prepare for this transition by using nsecs_to_jiffies() which
does away with the need for a division operation.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Since the PWM framework is switching struct pwm_args.period's datatype
to u64, prepare for this transition by using DIV64_U64_ROUND_CLOSEST to
handle a 64-bit divisor.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM framework is going to change the PWM period and duty cycles to
be 64-bit unsigned integers. To avoid build errors on platforms that do
not natively support 64-bit division, use explicity 64-bit division.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Since the PWM framework is switching struct pwm_state.period's
datatype to u64, prepare for this transition by using
DIV_ROUND_UP_ULL to handle a 64-bit dividend.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Since the PWM framework is switching struct pwm_state.period's datatype
to u64, prepare for this transition by using DIV64_U64_ROUND_CLOSEST to
handle a 64-bit divisor.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Since the PWM framework is switching struct pwm_args.period's datatype
to u64, prepare for this transition by using DIV64_U64_ROUND_CLOSEST to
handle a 64-bit divisor.
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The IS_ENABLED() use was missing the CONFIG_ prefix which would have
lead to skipping this code.
Fixes: 3ad1f3a33286 ("pwm: Implement some checks for lowlevel drivers")
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
