| Age | Commit message (Collapse) | Author |
|---|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"First of all, the adaptive voltage scaling (AVS) drivers go to new
platform-specific locations as planned (this part was reported to have
merge conflicts against the new arm-soc updates in linux-next).
In addition to that, there are some fixes (intel_idle, intel_pstate,
RAPL, acpi_cpufreq), the addition of on/off notifiers and idle state
accounting support to the generic power domains (genpd) code and some
janitorial changes all over.
Specifics:
- Move the AVS drivers to new platform-specific locations and get rid
of the drivers/power/avs directory (Ulf Hansson).
- Add on/off notifiers and idle state accounting support to the
generic power domains (genpd) framework (Ulf Hansson, Lina Iyer).
- Ulf will maintain the PM domain part of cpuidle-psci (Ulf Hansson).
- Make intel_idle disregard ACPI _CST if it cannot use the data
returned by that method (Mel Gorman).
- Modify intel_pstate to avoid leaving useless sysfs directory
structure behind if it cannot be registered (Chen Yu).
- Fix domain detection in the RAPL power capping driver and prevent
it from failing to enumerate the Psys RAPL domain (Zhang Rui).
- Allow acpi-cpufreq to use ACPI _PSD information with Family 19 and
later AMD chips (Wei Huang).
- Update the driver assumptions comment in intel_idle and fix a
kerneldoc comment in the runtime PM framework (Alexander Monakov,
Bean Huo).
- Avoid unnecessary resets of the cached frequency in the schedutil
cpufreq governor to reduce overhead (Wei Wang).
- Clean up the cpufreq core a bit (Viresh Kumar).
- Make assorted minor janitorial changes (Daniel Lezcano, Geert
Uytterhoeven, Hubert Jasudowicz, Tom Rix).
- Clean up and optimize the cpupower utility somewhat (Colin Ian
King, Martin Kaistra)"
* tag 'pm-5.10-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
PM: sleep: remove unreachable break
PM: AVS: Drop the avs directory and the corresponding Kconfig
PM: AVS: qcom-cpr: Move the driver to the qcom specific drivers
PM: runtime: Fix typo in pm_runtime_set_active() helper comment
PM: domains: Fix build error for genpd notifiers
powercap: Fix typo in Kconfig "Plance" -> "Plane"
cpufreq: schedutil: restore cached freq when next_f is not changed
acpi-cpufreq: Honor _PSD table setting on new AMD CPUs
PM: AVS: smartreflex Move driver to soc specific drivers
PM: AVS: rockchip-io: Move the driver to the rockchip specific drivers
PM: domains: enable domain idle state accounting
PM: domains: Add curly braces to delimit comment + statement block
PM: domains: Add support for PM domain on/off notifiers for genpd
powercap/intel_rapl: enumerate Psys RAPL domain together with package RAPL domain
powercap/intel_rapl: Fix domain detection
intel_idle: Ignore _CST if control cannot be taken from the platform
cpuidle: Remove pointless stub
intel_idle: mention assumption that WBINVD is not needed
MAINTAINERS: Add section for cpuidle-psci PM domain
cpufreq: intel_pstate: Delete intel_pstate sysfs if failed to register the driver
...
|
|
All avs drivers have now been moved to their corresponding soc specific
directories. Additionally, they don't depend on the POWER_AVS Kconfig
anymore. Therefore, let's simply drop the drivers/power/avs directory
altogether.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The avs drivers are all SoC specific drivers that doesn't share any code.
Instead they are located in a directory, mostly to keep similar
functionality together. From a maintenance point of view, it makes better
sense to collect SoC specific drivers like these, into the SoC specific
directories.
Therefore, let's move the qcom-cpr driver to the qcom directory.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Niklas Cassel <nks@flawful.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- add wireless type
- properly document current direction
Battery/charger driver changes:
- new fuel-gauge/charger driver for RN5T618/RN5T619
- new charger driver for BQ25980, BQ25975 and BQ25960
- bq27xxx-battery: add support for TI bq34z100
- gpio-charger: convert to GPIO descriptors
- gpio-charger: add optional support for charge current limiting
- max17040: add support for max17041, max17043, max17044
- max17040: add support for max17048, max17049, max17058, max17059
- smb347-charger: add DT support
- smb247-charger: add SMB345 and SMB358 support
- simple-battery: add temperature properties
- lots of minor fixes, cleanups and DT binding YAML conversions
Reset drivers:
- ocelot: Add support for Sparx5"
* tag 'for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (81 commits)
power: reset: POWER_RESET_OCELOT_RESET should depend on Ocelot or Sparx5
power: supply: bq25980: Fix uninitialized wd_reg_val and overrun
power: supply: ltc2941: Fix ptr to enum cast
power: supply: test-power: revise parameter printing to use sprintf
power: supply: charger-manager: fix incorrect check on charging_duration_ms
power: supply: max17040: Fix ptr to enum cast
power: supply: bq25980: Fix uninitialized wd_reg_val
power: supply: bq25980: remove redundant zero check on ret
power: reset: ocelot: Add support for Sparx5
dt-bindings: reset: ocelot: Add Sparx5 support
power: supply: sbs-battery: keep error code when get_property() fails
power: supply: bq25980: Add support for the BQ259xx family
dt-binding: bq25980: Add the bq25980 flash charger
power: supply: fix spelling mistake "unprecise" -> "imprecise"
power: supply: test_power: add missing newlines when printing parameters by sysfs
power: supply: pm2301: drop duplicated i2c_device_id
power: supply: charger-manager: drop unused charger assignment
power: supply: rt9455: skip 'struct acpi_device_id' when !CONFIG_ACPI
power: supply: goldfish: skip 'struct acpi_device_id' when !CONFIG_ACPI
power: supply: bq25890: skip 'struct acpi_device_id' when !CONFIG_ACPI
...
|
|
The avs drivers are all SoC specific drivers that doesn't share any code.
Instead they are located in a directory, mostly to keep similar
functionality together. From a maintenance point of view, it makes better
sense to collect SoC specific drivers like these, into the SoC specific
directories.
Therefore, let's move the smartreflex driver for OMAP to the ti directory.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The avs drivers are all SoC specific drivers that doesn't share any code.
Instead they are located in a directory, mostly to keep similar
functionality together. From a maintenance point of view, it makes better
sense to collect SoC specific drivers like these, into the SoC specific
directories.
Therefore, let's move the rockchip-io driver to the rockchip directory.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To add support for Sparx5, the dependency on MSCC_OCELOT was removed.
However, this increases exposure of the driver question not only to
Sparx5 platforms, but to everyone. Hence re-add the dependency on
MSCC_OCELOT, and extend it with ARCH_SPARX5, to prevent asking the user
about this driver when configuring a kernel without Ocelot and Sparx5
support.
Fixes: ec871696b7776767 ("power: reset: ocelot: Add support for Sparx5")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char, misc, and other assorted driver subsystem
patches for 5.10-rc1.
There's a lot of different things in here, all over the drivers/
directory. Some summaries:
- soundwire driver updates
- habanalabs driver updates
- extcon driver updates
- nitro_enclaves new driver
- fsl-mc driver and core updates
- mhi core and bus updates
- nvmem driver updates
- eeprom driver updates
- binder driver updates and fixes
- vbox minor bugfixes
- fsi driver updates
- w1 driver updates
- coresight driver updates
- interconnect driver updates
- misc driver updates
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (396 commits)
binder: fix UAF when releasing todo list
docs: w1: w1_therm: Fix broken xref, mistakes, clarify text
misc: Kconfig: fix a HISI_HIKEY_USB dependency
LSM: Fix type of id parameter in kernel_post_load_data prototype
misc: Kconfig: add a new dependency for HISI_HIKEY_USB
firmware_loader: fix a kernel-doc markup
w1: w1_therm: make w1_poll_completion static
binder: simplify the return expression of binder_mmap
test_firmware: Test partial read support
firmware: Add request_partial_firmware_into_buf()
firmware: Store opt_flags in fw_priv
fs/kernel_file_read: Add "offset" arg for partial reads
IMA: Add support for file reads without contents
LSM: Add "contents" flag to kernel_read_file hook
module: Call security_kernel_post_load_data()
firmware_loader: Use security_post_load_data()
LSM: Introduce kernel_post_load_data() hook
fs/kernel_read_file: Add file_size output argument
fs/kernel_read_file: Switch buffer size arg to size_t
fs/kernel_read_file: Remove redundant size argument
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These rework the collection of cpufreq statistics to allow it to take
place if fast frequency switching is enabled in the governor, rework
the frequency invariance handling in the cpufreq core and drivers, add
new hardware support to a couple of cpufreq drivers, fix a number of
assorted issues and clean up the code all over.
Specifics:
- Rework cpufreq statistics collection to allow it to take place when
fast frequency switching is enabled in the governor (Viresh Kumar).
- Make the cpufreq core set the frequency scale on behalf of the
driver and update several cpufreq drivers accordingly (Ionela
Voinescu, Valentin Schneider).
- Add new hardware support to the STI and qcom cpufreq drivers and
improve them (Alain Volmat, Manivannan Sadhasivam).
- Fix multiple assorted issues in cpufreq drivers (Jon Hunter,
Krzysztof Kozlowski, Matthias Kaehlcke, Pali Rohár, Stephan
Gerhold, Viresh Kumar).
- Fix several assorted issues in the operating performance points
(OPP) framework (Stephan Gerhold, Viresh Kumar).
- Allow devfreq drivers to fetch devfreq instances by DT enumeration
instead of using explicit phandles and modify the devfreq core code
to support driver-specific devfreq DT bindings (Leonard Crestez,
Chanwoo Choi).
- Improve initial hardware resetting in the tegra30 devfreq driver
and clean up the tegra cpuidle driver (Dmitry Osipenko).
- Update the cpuidle core to collect state entry rejection statistics
and expose them via sysfs (Lina Iyer).
- Improve the ACPI _CST code handling diagnostics (Chen Yu).
- Update the PSCI cpuidle driver to allow the PM domain
initialization to occur in the OSI mode as well as in the PC mode
(Ulf Hansson).
- Rework the generic power domains (genpd) core code to allow domain
power off transition to be aborted in the absence of the "power
off" domain callback (Ulf Hansson).
- Fix two suspend-to-idle issues in the ACPI EC driver (Rafael
Wysocki).
- Fix the handling of timer_expires in the PM-runtime framework on
32-bit systems and the handling of device links in it (Grygorii
Strashko, Xiang Chen).
- Add IO requests batching support to the hibernate image saving and
reading code and drop a bogus get_gendisk() from there (Xiaoyi
Chen, Christoph Hellwig).
- Allow PCIe ports to be put into the D3cold power state if they are
power-manageable via ACPI (Lukas Wunner).
- Add missing header file include to a power capping driver (Pujin
Shi).
- Clean up the qcom-cpr AVS driver a bit (Liu Shixin).
- Kevin Hilman steps down as designated reviwer of adaptive voltage
scaling (AVS) drivers (Kevin Hilman)"
* tag 'pm-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (65 commits)
cpufreq: stats: Fix string format specifier mismatch
arm: disable frequency invariance for CONFIG_BL_SWITCHER
cpufreq,arm,arm64: restructure definitions of arch_set_freq_scale()
cpufreq: stats: Add memory barrier to store_reset()
cpufreq: schedutil: Simplify sugov_fast_switch()
ACPI: EC: PM: Drop ec_no_wakeup check from acpi_ec_dispatch_gpe()
ACPI: EC: PM: Flush EC work unconditionally after wakeup
PCI/ACPI: Whitelist hotplug ports for D3 if power managed by ACPI
PM: hibernate: remove the bogus call to get_gendisk() in software_resume()
cpufreq: Move traces and update to policy->cur to cpufreq core
cpufreq: stats: Enable stats for fast-switch as well
cpufreq: stats: Mark few conditionals with unlikely()
cpufreq: stats: Remove locking
cpufreq: stats: Defer stats update to cpufreq_stats_record_transition()
PM: domains: Allow to abort power off when no ->power_off() callback
PM: domains: Rename power state enums for genpd
PM / devfreq: tegra30: Improve initial hardware resetting
PM / devfreq: event: Change prototype of devfreq_event_get_edev_by_phandle function
PM / devfreq: Change prototype of devfreq_get_devfreq_by_phandle function
PM / devfreq: Add devfreq_get_devfreq_by_node function
...
|
|
Fix the issue when 'i' is equal to array size then array index over
runs the array when checking for the watch dog value.
Fixes: 5069185fc18e ("power: supply: bq25980: Add support for the BQ259xx family")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
clang complains about casting pointers to smaller enum types.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fix from Sebastian Reichel:
"Just a single change to revert enablement of packet error checking for
battery data on Chromebooks, since some of their embedded controllers
do not handle it correctly"
* tag 'for-v5.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: supply: sbs-battery: chromebook workaround for PEC
|
|
Looks like the I2C tunnel implementation from Chromebook's
embedded controller does not handle PEC correctly. Fix this
by disabling PEC for batteries behind those I2C tunnels as
a workaround.
Note, that some Chromebooks actually have been reported to
have working PEC support (with I2C tunnel). Since the problem
has not yet been fully understood this simply reverts all
Chromebooks to not use PEC for now.
Reported-by: "Milan P. Stanić" <mps@arvanta.net>
Reported-by: Vicente Bergas <vicencb@gmail.com>
CC: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Fixes: 7222bd603dd2 ("power: supply: sbs-battery: add PEC support")
Tested-by: Vicente Bergas <vicencb@gmail.com>
Tested-by: "Milan P. Stanić" <mps@arvanta.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Simplify code by using sprintf instead of strcpy+strcat+strlen.
Signed-off-by: Harley A.W. Lorenzo <hl1998@protonmail.com>
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Currently the duration check on the discharging duration setting is
checking the charging duration rather than the discharging duration
due to a cut-n-paste coding error. Fix this by checking the value
desc->charging_max_duration_ms.
Addresses-Coverity: ("Copy-paste-error")
Fixes: 8fcfe088e21a ("charger-manager: Support limit of maximum possible")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
clang complains about casting pointers to smaller enum types.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Fix the uninitialized wd_reg_val if the for..loop was not successful in
finding an appropriate match.
Fixes: 5069185fc18e ("power: supply: bq25980: Add support for the BQ259xx family")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Currently ret is assigned to zero and the following statement checks
if it is non-zero. This check is redundant and can be removed
Addresses-Coverity: ("Logically dead code")
Fixes: 5069185fc18e ("power: supply: bq25980: Add support for the BQ259xx family")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This adds reset support for Sparx5 in the ocelot-reset driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Commit 395a7251dc2b (power: supply: sbs-battery: don't assume
i2c errors as battery disconnect) overwrites the original error code
returned from internal functions. On such a sporadic i2c error,
a user will get a wrong value without errors.
Fixes: 395a7251dc2b (power: supply: sbs-battery: don't assume i2c errors as battery disconnect)
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The only usage of these structs is to assign their address to the fops
field in the w1_family struct, which is a const pointer. Make them const
to allow the compiler to put them in read-only memory.
This was done with the following Coccinelle semantic patch
(http://coccinelle.lip6.fr/):
// <smpl>
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct w1_family_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
identifier s;
@@
static struct w1_family s = {
.fops=&i@p,
};
@bad1@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad1 disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct w1_family_ops i={};
// </smpl>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201004193202.4044-4-rikard.falkeborn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for the BQ25980, BQ25975 and BQ25960 family of flash
chargers.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
There is a spelling mistake in a dev_info message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
sysfs
When I cat some module parameters by sysfs, it displays as follows.
It's better to add a newline for easy reading.
root@syzkaller:~# cd /sys/module/test_power/parameters/
root@syzkaller:/sys/module/test_power/parameters# cat ac_online
onroot@syzkaller:/sys/module/test_power/parameters# cat battery_present
trueroot@syzkaller:/sys/module/test_power/parameters# cat battery_health
goodroot@syzkaller:/sys/module/test_power/parameters# cat battery_status
dischargingroot@syzkaller:/sys/module/test_power/parameters# cat battery_technology
LIONroot@syzkaller:/sys/module/test_power/parameters# cat usb_online
onroot@syzkaller:/sys/module/test_power/parameters#
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The driver defines two of 'struct i2c_device_id' but uses only one:
drivers/power/supply/pm2301_charger.c:107:35: warning:
'pm2xxx_ident' defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The 'charger' variable in error path is assigned but never used:
drivers/power/supply/charger-manager.c: In function 'charger_manager_probe':
drivers/power/supply/charger-manager.c:1626:29: warning: variable 'charger' set but not used [-Wunused-but-set-variable]
Fixes: c1f73028f75d ("power: supply: charger-manager: Update extcon functions")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI, the
struct acpi_device_id becomes unused:
drivers/power/supply/rt9455_charger.c:1734:36: warning:
'rt9455_i2c_acpi_match' defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI, the
struct acpi_device_id becomes unused:
drivers/power/supply/goldfish_battery.c:269:36: warning:
'goldfish_battery_acpi_match' defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI, the
struct acpi_device_id becomes unused:
drivers/power/supply/bq25890_charger.c:1076:36: warning:
'bq25890_acpi_match' defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Fix kerneldoc W=1 warning:
drivers/power/supply/bq2515x_charger.c:189: warning:
Function parameter or member 'init_data' not described in 'bq2515x_device'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI, the
struct acpi_device_id becomes unused:
drivers/power/supply/bq24257_charger.c:1155:36: warning:
'bq24257_acpi_match' defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
max17048 and max17049 support SOC alerts (interrupts when battery
capacity changes by +/- 1%). At the moment the driver polls for changes
every second. Using the alerts removes the need for polling.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The Maxim ModelGauge family supports fine-tuning by setting
a compensation value (named rcomp in the docs). The value is affected by
battery chemistry and ambient temperature.
Add support for reading maxim,rcomp from DT and configuring the device
with the supplied value. Temperature adjustment is not implemented at
the moment, because there is no provision for receiving the ambient
temperature at the moment.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The max17040 fuel gauge is part of a family of 8 chips that have very
similar mode of operations and registers.
This change adds:
- compatible strings for all supported devices and handling for the
minor differences between them;
- handling for devices reporting double capacity via maxim,double-soc;
The datasheets of the supported devices are linked [0] [1] [2] [3].
[0] https://datasheets.maximintegrated.com/en/ds/MAX17040-MAX17041.pdf
[1] https://datasheets.maximintegrated.com/en/ds/MAX17043-MAX17044.pdf
[2] https://datasheets.maximintegrated.com/en/ds/MAX17048-MAX17049.pdf
[3] https://datasheets.maximintegrated.com/en/ds/MAX17058-MAX17059.pdf
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Rewrite i2c operations from i2c client read/write to regmap i2c. As
a result, most private functions now accept the private driver data
instead of an i2c client pointer.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Two actions were performed during remove - power supply dereg and
delayed work cleanup. Power supply dereg can be handled by using the
devm_ version of the registration function. Work cleanup can be added as
a devm_action.
If probe fails after psy registration it will now be cleaned up
properly.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add support for new device: the TI bq34z100-G1, a Wide Range Fuel Gauge
for Li-Ion, PbA, NiMH, and NiCd batteries. The device shares a lot with
other models, although it has its own differences requiring new quirks.
This patch was tested on a system equipped with NiMH batteries.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
bq27000, bq27010 and upcoming bq34z100 have a Capacity Inaccurate flag.
However except this similarity, bq34z100 is quite different than
bq27000/bq27010, so flag BQ27XXX_O_ZERO cannot be reused here. Add
a new bit flag describing this capability.
No functional change for bq27000 and bq27010.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
bq27000, bq27010 and upcoming bq34z100 have a single byte SoC
register. However except this similarity, bq34z100 is quite different
than bq27000/bq27010, so flag BQ27XXX_O_ZERO cannot be reused here. Add
a new bit flag describing that SoC is a single byte register.
No functional change for bq27000 and bq27010.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
BIT() is a preferred way to toggle bit-like flags: no problems with 32/64
bit systems, less chances for mistakes. Remove also unneeded
whitespace.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Commit 6f24ff97e323 ("power: supply: bq27xxx_battery: Add the
BQ27Z561 Battery monitor") and commit d74534c27775 ("power:
bq27xxx_battery: Add support for additional bq27xxx family devices")
added support for new device types by copying most of the code and
adding necessary quirks.
However they did not copy the code in bq27xxx_battery_status()
responsible for returning POWER_SUPPLY_STATUS_NOT_CHARGING.
Unify the bq27xxx_battery_status() so for all types when charger is
supplied, it will return "not charging" status.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Some fault events like the over-current condition will get resolved
by the hardware, by e.g. disabling the port. As the status in the
interrupt status register is cleared on read when the fault is resolved,
the sysfs health property will only contain the correct health status
for the first time it is read after such an event, even if the actual
fault condition (like a VBUS short) still persists. To reflect this
properly in the property we cache the last health status and only update
the cache when a actual change happens, i.e. the ERR bit in the status
register flips, as this one properly reflects a continued fault condition.
The ALERT pin however, is not driven by the ERR status, but by the actual
fault status, so the pin will change back to it's default state when the
hardware has automatically resolved the fault by cutting the power. Thus
we never get an IRQ when the actual fault condition has been resolved and
the ERR status bit has been cleared in auto-recovery mode. To get this
information we need to poll the interrupt status register after some time
to see if the fault is gone and update our cache in that case.
To avoid any additional locking, we handle both paths (IRQ firing and
delayed polling) through the same single-threaded delayed work.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Modify the comment typo: "compliment" -> "complement".
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add configuration for compensation of IBAT measuring resistor in series
with the battery.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Modify the comment typo: "compliment" -> "complement".
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Simplify the return expression.
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
[ rjw: Minor subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Rather than having a cm-chargers and a separate cm-num-chargers
property, simply count the entries in cm-chargers.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
In commit 830ae442202e ("extcon: Remove the deprecated extcon functions")
the function extcon_register_interest became a no-op returning an error,
leading to non-functional behaviour in charger-manager.
Additionally, a translation table is needed between the text representation
of the extcon cable names and their IDs is needed. In order to retain DT
compatibility, TA and CHARGE-DOWNSTREAM are added as they were present up
until commit 11eecf910bd8 ("extcon: Modify the id and name of external
connector")
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
