| Age | Commit message (Collapse) | Author |
|---|
|
IRQF_NO_AUTOEN flag"
It causes mlxreg-hotplug probing failure: request_threaded_irq()
returns -EINVAL due to true value of condition:
((irqflags & IRQF_SHARED) && (irqflags & IRQF_NO_AUTOEN))
after flag "IRQF_NO_AUTOEN" has been added to:
err = devm_request_irq(&pdev->dev, priv->irq,
mlxreg_hotplug_irq_handler, IRQF_TRIGGER_FALLING
| IRQF_SHARED | IRQF_NO_AUTOEN,
"mlxreg-hotplug", priv);
This reverts commit bee3ecfed0fc ("platform/mellanox: mlxreg-hotplug: move
to use request_irq by IRQF_NO_AUTOEN flag").
Signed-off-by: Mykola Kostenok <c_mykolak@nvidia.com>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210603172827.2599908-1-c_mykolak@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The virtio framework uses wmb() when updating avail->idx. It
guarantees the write order, but not necessarily loading order
for the code accessing the memory. This commit adds a load barrier
after reading the avail->idx to make sure all the data in the
descriptor is visible. It also adds a barrier when returning the
packet to virtio framework to make sure read/writes are visible to
the virtio code.
Fixes: 1357dfd7261f ("platform/mellanox: Add TmFifo driver for Mellanox BlueField Soc")
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/1620433812-17911-1-git-send-email-limings@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
flag
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable because of requesting.
this patch is made base on "add IRQF_NO_AUTOEN for request_irq" which
is being merged: https://lore.kernel.org/patchwork/patch/1388765/
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/1617785983-28878-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
s/progamming/programming/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210317095650.2036419-1-unixbhaskar@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The performance modules in BlueField are present in several hardware
blocks and each block provides access to these stats either through
counters that can be programmed to monitor supported events or
through memory-mapped registers that hold the relevant information.
The hardware blocks that include a performance module are:
* Tile (block containing 2 cores and a shared L2 cache)
* TRIO (PCIe root complex)
* MSS (Memory Sub-system containing the Memory Controller and L3 cache)
* GIC (Interrupt controller)
* SMMU (System Memory Management Unit)
The mlx_pmc driver provides access to all of these performance modules
through a hwmon sysfs interface.
v2 --> v3
Update copyright info.
v1 --> v2
Remove unused headers.
Add comma to arrays where last line is not a termination.
Use kstrtoint in place of sscanf.
UUID manipulation follows drivers/platform/mellanox/mlxbf-bootctl.c
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/4e19a1e5bf4197ad27fc57981fd280eaebd23577.1602160468.git.shravankr@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Pull virtio updates from Michael Tsirkin:
- IRQ bypass support for vdpa and IFC
- MLX5 vdpa driver
- Endianness fixes for virtio drivers
- Misc other fixes
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (71 commits)
vdpa/mlx5: fix up endian-ness for mtu
vdpa: Fix pointer math bug in vdpasim_get_config()
vdpa/mlx5: Fix pointer math in mlx5_vdpa_get_config()
vdpa/mlx5: fix memory allocation failure checks
vdpa/mlx5: Fix uninitialised variable in core/mr.c
vdpa_sim: init iommu lock
virtio_config: fix up warnings on parisc
vdpa/mlx5: Add VDPA driver for supported mlx5 devices
vdpa/mlx5: Add shared memory registration code
vdpa/mlx5: Add support library for mlx5 VDPA implementation
vdpa/mlx5: Add hardware descriptive header file
vdpa: Modify get_vq_state() to return error code
net/vdpa: Use struct for set/get vq state
vdpa: remove hard coded virtq num
vdpasim: support batch updating
vhost-vdpa: support IOTLB batching hints
vhost-vdpa: support get/set backend features
vhost: generialize backend features setting/getting
vhost-vdpa: refine ioctl pre-processing
vDPA: dont change vq irq after DRIVER_OK
...
|
|
mlxbf-tmfifo accesses config space using native types -
which works for it since the legacy virtio native types.
This will break if it ever needs to support modern virtio,
so with new tags previously introduced for virtio net config,
sparse now warns for this in drivers.
Since this is a legacy only device, fix it up using
virtio_legacy_is_little_endian for now.
No functional changes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
|
|
Add support for attributes composed from few registers.
Such attributes could occupy from 2 to 4 sequential registers.
For word size register space complex attributes can occupy up to two
registers, for byte size - up to four. These attributes can carry, for
example, CPLD or FPGA versioning, power consuming info, etcetera.
Such registers contain read-only data.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Send "udev" event with environmental data in order to allow handling
"ENV{}" variables in "udev" rules.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
creation
Create the 'sysfs' attributes according to configuration provided
through the capability register, which purpose is to indicate the
actual number of the components within the particular group.
Such components could be, for example the FAN or power supply units.
The motivation is to avoid adding a new code in the future in order to
distinct between the systems types supporting a different number of the
components like power supplies, FANs, ASICs, line cards.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Change module license to 'SPDX'.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
treewide: replace '---help---' in Kconfig files with 'help'
kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
samples: binderfs: really compile this sample and fix build issues
|
|
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add support for capability register, which is used for detection of the
actual number of interrupt capable components within the particular
group, supported by the specific system.
Such components could be for example the number of power units and
interrupts related to these units.
The motivation is to avoid adding a new code in the future in order to
distinct between the systems type supported different number of the
components like power supplies, FANs, ASICs, line cards.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
This commit fixes the potential deadlock caused by the console Rx
and Tx processing at the same time. Rx and Tx both take the console
and tmfifo spinlock but in different order which causes potential
deadlock. The fix is to use different tmfifo spinlock for Rx and
Tx since they protect different resources and it's safe to split
the lock.
Below is the reported call trace when copying/pasting large string
in the console.
Rx:
_raw_spin_lock_irqsave (hvc lock)
__hvc_poll
hvc_poll
in_intr
vring_interrupt
mlxbf_tmfifo_rxtx_one_desc (tmfifo lock)
mlxbf_tmfifo_rxtx
mlxbf_tmfifo_work_rxtx
Tx:
_raw_spin_lock_irqsave (tmfifo lock)
mlxbf_tmfifo_virtio_notify
virtqueue_notify
virtqueue_kick
put_chars
hvc_push
hvc_write (hvc lock)
...
do_tty_write
tty_write
Fixes: 1357dfd7261f ("platform/mellanox: Add TmFifo driver for Mellanox BlueField Soc")
Cc: <stable@vger.kernel.org> # 5.4+
Reviewed-by: David Woods <dwoods@mellanox.com>
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
This is a follow-up commit for the sysfs attributes to change
from DRIVER_ATTR to DEVICE_ATTR according to some initial comments.
In such case, it's better to point the sysfs path to the device
itself instead of the driver. The ABI document is also updated.
Fixes: 79e29cb8fbc5 ("platform/mellanox: Add bootctl driver for Mellanox BlueField Soc")
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
This commit adds the bootctl platform driver for Mellanox BlueField
Soc, which queries secure state and controls the eMMC boot partition
swapping by sending SMC calls to ATF running at EL3.
Below are the sequences of typical use case.
1. User requests boot partition swapping, which could be on-demand or
during boot-image upgrade via UEFI capsule;
2. This bootctl driver handles the request and sends SMC call
to ATF. ATF programs register BREADCRUMB0 which has value
preserved during warm reset. It also programs eMMC to swap
the boot partition;
3. After software reset (rebooting), ATF BL1 (BootRom) checks
register BREADCRUMB0 and enable watchdog if configured;
4. If booting fails, the watchdog timer will trigger rebooting.
In such case, ATF Boot ROM will switch the boot partition
back to the previous one. This is a robust feature and used
to prevent failure during boot partition upgrade.
Reviewed-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
platform_get_irq()
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: "Darren Hart (VMware)" <dvhart@infradead.org>
Cc: Roman Kiryanov <rkir@google.com>
Cc: Vadim Pasternak <vadimp@mellanox.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add devm_free_irq() call to mlxreg-hotplug remove() for clean release
of devices irq resource. Fix debugobjects warning triggered by rmmod
It prevents of use-after-free memory, related to
mlxreg_hotplug_work_handler.
Issue has been reported as debugobjects warning triggered by
'rmmod mlxtreg-hotplug' flow, while running kernel with
CONFIG_DEBUG_OBJECTS* options.
[ 2489.623551] ODEBUG: free active (active state 0) object type: work_struct hint: mlxreg_hotplug_work_handler+0x0/0x7f0 [mlxreg_hotplug]
[ 2489.637097] WARNING: CPU: 5 PID: 3924 at lib/debugobjects.c:328 debug_print_object+0xfe/0x180
[ 2489.637165] RIP: 0010:debug_print_object+0xfe/0x180
?
[ 2489.637214] Call Trace:
[ 2489.637225] __debug_check_no_obj_freed+0x25e/0x320
[ 2489.637231] kfree+0x82/0x110
[ 2489.637238] release_nodes+0x33c/0x4e0
[ 2489.637242] ? devres_remove_group+0x1b0/0x1b0
[ 2489.637247] device_release_driver_internal+0x146/0x270
[ 2489.637251] driver_detach+0x73/0xe0
[ 2489.637254] bus_remove_driver+0xa1/0x170
[ 2489.637261] __x64_sys_delete_module+0x29e/0x320
[ 2489.637265] ? __ia32_sys_delete_module+0x320/0x320
[ 2489.637268] ? blkcg_exit_queue+0x20/0x20
[ 2489.637273] ? task_work_run+0x7d/0x100
[ 2489.637278] ? exit_to_usermode_loop+0x5b/0xf0
[ 2489.637281] do_syscall_64+0x73/0x160
[ 2489.637287] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 2489.637290] RIP: 0033:0x7f95c3596fd7
The difference in release flow with and with no devm_free_irq is listed
below:
bus: 'platform': remove driver mlxreg-hotplug
mlxreg_hotplug_remove(start)
-> devm_free_irq (with new code)
mlxreg_hotplug_remove (end)
release_nodes (start)
mlxreg-hotplug: DEVRES REL devm_hwmon_release (8 bytes)
device: 'hwmon3': device_unregister
PM: Removing info for No Bus:hwmon3
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (88 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (6 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_irq_release (16 bytes) (no new code)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (1376 bytes)
------------[ cut here ]------------ (no new code):
ODEBUG: free active (active state 0) object type: work_struct hint: mlxreg_hotplug_work_handler
release_nodes(end)
driver: 'mlxreg-hotplug': driver_release
Fixes: 1f976f6978bf ("platform/x86: Move Mellanox platform hotplug driver to platform/mellanox")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
This commit adds the TmFifo platform driver for Mellanox BlueField
Soc. TmFifo is a shared FIFO which enables external host machine
to exchange data with the SoC via USB or PCIe. The driver is based
on virtio framework and has console and network access enabled.
Reviewed-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Fix the following KASAN warning produced when booting a 64-bit kernel:
[ 13.334750] BUG: KASAN: stack-out-of-bounds in find_first_bit+0x19/0x70
[ 13.342166] Read of size 8 at addr ffff880235067178 by task kworker/2:1/42
[ 13.342176] CPU: 2 PID: 42 Comm: kworker/2:1 Not tainted 4.20.0-rc1+ #106
[ 13.342179] Hardware name: Mellanox Technologies Ltd. MSN2740/Mellanox x86 SFF board, BIOS 5.6.5 06/07/2016
[ 13.342190] Workqueue: events deferred_probe_work_func
[ 13.342194] Call Trace:
[ 13.342206] dump_stack+0xc7/0x15b
[ 13.342214] ? show_regs_print_info+0x5/0x5
[ 13.342220] ? kmsg_dump_rewind_nolock+0x59/0x59
[ 13.342234] ? _raw_write_lock_irqsave+0x100/0x100
[ 13.351593] print_address_description+0x73/0x260
[ 13.351603] kasan_report+0x260/0x380
[ 13.351611] ? find_first_bit+0x19/0x70
[ 13.351619] find_first_bit+0x19/0x70
[ 13.351630] mlxreg_hotplug_work_handler+0x73c/0x920 [mlxreg_hotplug]
[ 13.351639] ? __lock_text_start+0x8/0x8
[ 13.351646] ? _raw_write_lock_irqsave+0x80/0x100
[ 13.351656] ? mlxreg_hotplug_remove+0x1e0/0x1e0 [mlxreg_hotplug]
[ 13.351663] ? regmap_volatile+0x40/0xb0
[ 13.351668] ? regcache_write+0x4c/0x90
[ 13.351676] ? mlxplat_mlxcpld_reg_write+0x24/0x30 [mlx_platform]
[ 13.351681] ? _regmap_write+0xea/0x220
[ 13.351688] ? __mutex_lock_slowpath+0x10/0x10
[ 13.351696] ? devm_add_action+0x70/0x70
[ 13.351701] ? mutex_unlock+0x1d/0x40
[ 13.351710] mlxreg_hotplug_probe+0x82e/0x989 [mlxreg_hotplug]
[ 13.351723] ? mlxreg_hotplug_work_handler+0x920/0x920 [mlxreg_hotplug]
[ 13.351731] ? sysfs_do_create_link_sd.isra.2+0xf4/0x190
[ 13.351737] ? sysfs_rename_link_ns+0xf0/0xf0
[ 13.351743] ? devres_close_group+0x2b0/0x2b0
[ 13.351749] ? pinctrl_put+0x20/0x20
[ 13.351755] ? acpi_dev_pm_attach+0x2c/0xd0
[ 13.351763] platform_drv_probe+0x70/0xd0
[ 13.351771] really_probe+0x480/0x6e0
[ 13.351778] ? device_attach+0x10/0x10
[ 13.351784] ? __lock_text_start+0x8/0x8
[ 13.351790] ? _raw_write_lock_irqsave+0x80/0x100
[ 13.351797] ? _raw_write_lock_irqsave+0x80/0x100
[ 13.351806] ? __driver_attach+0x190/0x190
[ 13.351812] driver_probe_device+0x17d/0x1a0
[ 13.351819] ? __driver_attach+0x190/0x190
[ 13.351825] bus_for_each_drv+0xd6/0x130
[ 13.351831] ? bus_rescan_devices+0x20/0x20
[ 13.351837] ? __mutex_lock_slowpath+0x10/0x10
[ 13.351845] __device_attach+0x18c/0x230
[ 13.351852] ? device_bind_driver+0x70/0x70
[ 13.351859] ? __mutex_lock_slowpath+0x10/0x10
[ 13.351866] bus_probe_device+0xea/0x110
[ 13.351874] deferred_probe_work_func+0x1c9/0x290
[ 13.351882] ? driver_deferred_probe_add+0x1d0/0x1d0
[ 13.351889] ? preempt_notifier_dec+0x20/0x20
[ 13.351897] ? read_word_at_a_time+0xe/0x20
[ 13.351904] ? strscpy+0x151/0x290
[ 13.351912] ? set_work_pool_and_clear_pending+0x9c/0xf0
[ 13.351918] ? __switch_to_asm+0x34/0x70
[ 13.351924] ? __switch_to_asm+0x40/0x70
[ 13.351929] ? __switch_to_asm+0x34/0x70
[ 13.351935] ? __switch_to_asm+0x40/0x70
[ 13.351942] process_one_work+0x5cc/0xa00
[ 13.351952] ? pwq_dec_nr_in_flight+0x1e0/0x1e0
[ 13.351960] ? pci_mmcfg_check_reserved+0x80/0xb8
[ 13.351967] ? run_rebalance_domains+0x250/0x250
[ 13.351980] ? stack_access_ok+0x35/0x80
[ 13.351986] ? deref_stack_reg+0xa1/0xe0
[ 13.351994] ? schedule+0xcd/0x250
[ 13.352000] ? worker_enter_idle+0x2d6/0x330
[ 13.352006] ? __schedule+0xeb0/0xeb0
[ 13.352014] ? fork_usermode_blob+0x130/0x130
[ 13.352019] ? mutex_lock+0xa7/0x100
[ 13.352026] ? _raw_spin_lock_irq+0x98/0xf0
[ 13.352032] ? _raw_read_unlock_irqrestore+0x30/0x30
[ 13.352037] i2c i2c-2: Added multiplexed i2c bus 11
[ 13.352043] worker_thread+0x181/0xa80
[ 13.352052] ? __switch_to_asm+0x34/0x70
[ 13.352058] ? __switch_to_asm+0x40/0x70
[ 13.352064] ? process_one_work+0xa00/0xa00
[ 13.352070] ? __switch_to_asm+0x34/0x70
[ 13.352076] ? __switch_to_asm+0x40/0x70
[ 13.352081] ? __switch_to_asm+0x34/0x70
[ 13.352086] ? __switch_to_asm+0x40/0x70
[ 13.352092] ? __switch_to_asm+0x34/0x70
[ 13.352097] ? __switch_to_asm+0x40/0x70
[ 13.352105] ? __schedule+0x3d6/0xeb0
[ 13.352112] ? migrate_swap_stop+0x470/0x470
[ 13.352119] ? save_stack+0x89/0xb0
[ 13.352127] ? kmem_cache_alloc_trace+0xe5/0x570
[ 13.352132] ? kthread+0x59/0x1d0
[ 13.352138] ? ret_from_fork+0x35/0x40
[ 13.352154] ? __schedule+0xeb0/0xeb0
[ 13.352161] ? remove_wait_queue+0x150/0x150
[ 13.352169] ? _raw_write_lock_irqsave+0x80/0x100
[ 13.352175] ? __lock_text_start+0x8/0x8
[ 13.352183] ? process_one_work+0xa00/0xa00
[ 13.352188] kthread+0x1a4/0x1d0
[ 13.352195] ? kthread_create_worker_on_cpu+0xc0/0xc0
[ 13.352202] ret_from_fork+0x35/0x40
[ 13.353879] The buggy address belongs to the page:
[ 13.353885] page:ffffea0008d419c0 count:0 mapcount:0 mapping:0000000000000000 index:0x0
[ 13.353890] flags: 0x2ffff8000000000()
[ 13.353897] raw: 02ffff8000000000 ffffea0008d419c8 ffffea0008d419c8 0000000000000000
[ 13.353903] raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
[ 13.353905] page dumped because: kasan: bad access detected
[ 13.353908] Memory state around the buggy address:
[ 13.353912] ffff880235067000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 13.353917] ffff880235067080: 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1 04
[ 13.353921] >ffff880235067100: f2 f2 f2 f2 f2 f2 f2 04 f2 f2 f2 f2 f2 f2 f2 04
[ 13.353923] ^
[ 13.353927] ffff880235067180: f2 f2 f2 f2 f2 f2 f2 04 f2 f2 f2 00 00 00 00 00
[ 13.353931] ffff880235067200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 13.353933] ==================================================================
The warning is caused by the below loop:
for_each_set_bit(bit, (unsigned long *)&asserted, 8) {
while "asserted" is declared as 'unsigned'.
The casting of 32-bit unsigned integer pointer to a 64-bit unsigned long
pointer. There are two problems here.
It causes the access of four extra byte, which can corrupt memory
The 32-bit pointer address may not be 64-bit aligned.
The fix changes variable "asserted" to "unsigned long".
Fixes: 1f976f6978bf ("platform/x86: Move Mellanox platform hotplug driver to platform/mellanox")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Provide support for the fan capability registers for the next generation
systems of types MQM87xx, MSN34xx, MSN37xx. These new registers provide
configuration for tachometers and fan drawers connectivity. Use these
registers for next generation led, fan and hotplug structures in order
to distinguish between the systems which have minor configuration
differences. This reduces the amount of code used to describe such
systems.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Notify user when hotplug device signal is received in order to allow user
to handle such case, if it wishes to take some action on this matter.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Simplify the logic of ASIC health discovery.
ASIC device can indicate its health state as a good, booting or dormant.
During ASIC reset the device is dropped to dormant state and should get to
the stable good health state through the intermediate booting state.
The sequence for getting to the steady state health after reset is:
(dormant -> booting -> good)+.
Initial implementation assumes that ?good? within this sequence is always
repeated twice and device is getting steady state only after the second
?good?. This patch removes this dependency, since the second ?good? is
received because of the noise on line and can be ignored. Device reaches
steady state after the first ?good? is received.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
As already done treewide, switch from open-coded multiplication to using
2-factor allocation helpers.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Introduce new Mellanox platform driver to allow access to Mellanox
programmable device register space trough sysfs interface.
The driver purpose is to provide sysfs interface for user space for the
registers essential for system control and monitoring.
The sets of registers for sysfs access are supposed to be defined per
system type bases and include the registers related to system resets
operation, system reset causes monitoring and some kinds of mux selection.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
[dvhart: Kconfig typo fixes spotted by Randy Dunlap]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Several incremental improvements including new keycodes, new models,
new quirks, and related documentation. Adds LED platform driver
activation for Mellanox systems. Some minor optimizations and
cleanups. Includes several bug fixes, message silencing, mostly minor
Automated summary:
acer-wmi:
- add another KEY_POWER keycode
apple-gmux:
- fix gmux_get_client_id()'s return type
asus-laptop:
- Simplify getting .drvdata
asus-wireless:
- Fix format specifier
dell-laptop:
- Fix keyboard backlight timeout on XPS 13 9370
dell-smbios:
- Match on www.dell.com in OEM strings too
dell-wmi:
- Ignore new rfkill and fn-lock events
- Set correct keycode for Fn + left arrow
fujitsu-laptop:
- Simplify soft key handling
ideapad-laptop:
- Add E42-80 to no_hw_rfkill
- Add fn-lock setting
- Add MIIX 720-12IKB to no_hw_rfkill
lib/string_helpers:
- Add missed declaration of struct task_struct
intel_scu_ipc:
- Replace mdelay with usleep_range in intel_scu_ipc_i2c_cntrl
mlx-platform:
- Add LED platform driver activation
platform/mellanox:
- Add new ODM system types to mlx-platform
- mlxreg-hotplug: add extra cycle for hotplug work queue
- mlxreg-hotplug: Document fixes for hotplug private data
platform_data/mlxreg:
- Document fixes for hotplug device
silead_dmi:
- Add entry for Chuwi Hi8 tablet touchscreen
- Add touchscreen info for the Onda V891w tablet
- Add info for the PoV mobii TAB-P800W (v2.0)
- Add touchscreen info for the Jumper EZpad 6 Pro
thinkpad_acpi:
- silence false-positive-prone pr_warn
- do not report thermal sensor state for tablet mode switch
- silence HKEY 0x6032, 0x60f0, 0x6030"
* tag 'platform-drivers-x86-v4.18-1' of git://git.infradead.org/linux-platform-drivers-x86: (30 commits)
platform/x86: silead_dmi: Add entry for Chuwi Hi8 tablet touchscreen
platform/x86: dell-laptop: Fix keyboard backlight timeout on XPS 13 9370
platform/x86: dell-wmi: Ignore new rfkill and fn-lock events
platform/x86: mlx-platform: Add LED platform driver activation
platform/mellanox: Add new ODM system types to mlx-platform
platform/mellanox: mlxreg-hotplug: add extra cycle for hotplug work queue
platform/x86: ideapad-laptop: Add E42-80 to no_hw_rfkill
platform/x86: silead_dmi: Add touchscreen info for the Onda V891w tablet
platform/x86: silead_dmi: Add info for the PoV mobii TAB-P800W (v2.0)
platform/x86: silead_dmi: Add touchscreen info for the Jumper EZpad 6 Pro
platform/x86: asus-wireless: Fix format specifier
platform/x86: asus-wmi: Fix NULL pointer dereference
platform/x86: dell-wmi: Set correct keycode for Fn + left arrow
platform/x86: acer-wmi: add another KEY_POWER keycode
platform/x86: ideapad-laptop: Add fn-lock setting
platform/x86: ideapad-laptop: Add MIIX 720-12IKB to no_hw_rfkill
lib/string_helpers: Add missed declaration of struct task_struct
platform/x86: DELL_WMI use depends on instead of select for DELL_SMBIOS
platform/mellanox: mlxreg-hotplug: Document fixes for hotplug private data
platform_data/mlxreg: Document fixes for hotplug device
...
|
|
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc().
This patch replaces cases of:
devm_kzalloc(handle, a * b, gfp)
with:
devm_kcalloc(handle, a * b, gfp)
as well as handling cases of:
devm_kzalloc(handle, a * b * c, gfp)
with:
devm_kzalloc(handle, array3_size(a, b, c), gfp)
as it's slightly less ugly than:
devm_kcalloc(handle, array_size(a, b), c, gfp)
This does, however, attempt to ignore constant size factors like:
devm_kzalloc(handle, 4 * 1024, gfp)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
Some manual whitespace fixes were needed in this patch, as Coccinelle
really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...".
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
expression HANDLE;
type TYPE;
expression THING, E;
@@
(
devm_kzalloc(HANDLE,
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
devm_kzalloc(HANDLE,
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression HANDLE;
expression COUNT;
typedef u8;
typedef __u8;
@@
(
devm_kzalloc(HANDLE,
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(char) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
expression HANDLE;
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)
// 2-factor product, only identifiers.
@@
expression HANDLE;
identifier SIZE, COUNT;
@@
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- SIZE * COUNT
+ COUNT, SIZE
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression HANDLE;
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
devm_kzalloc(HANDLE,
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression HANDLE;
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
expression HANDLE;
identifier STRIDE, SIZE, COUNT;
@@
(
devm_kzalloc(HANDLE,
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression HANDLE;
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
devm_kzalloc(HANDLE,
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression HANDLE;
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@
(
devm_kzalloc(HANDLE, sizeof(THING) * C2, ...)
|
devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...)
|
devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
devm_kzalloc(HANDLE, C1 * C2, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- (E1) * E2
+ E1, E2
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- (E1) * (E2)
+ E1, E2
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- E1 * E2
+ E1, E2
, ...)
)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Add extra cycle for hotplug work queue to handle the case when a signal is
It adds missed logic for signal acknowledge, by adding an extra run for
received, but no specific signal assertion is detected. Such case
theoretically can happen for example in case several units are removed or
inserted at the same time. In this situation acknowledge for some signal
can be missed at signal top aggreagation status level. The extra run will
allow to handler to acknowledge the missed signal.
The interrupt handling flow performs the next steps:
(1)
Enter mlxreg_hotplug_work_handler due to signal assertion.
Aggregation status register is changed for example from 0xff to 0xfd
(event signal group related to bit 1).
(2)
Mask aggregation interrupts, read aggregation status register and save it
(0xfd) in aggr_cache, then traverse down to handle signal from groups
related to the changed bit.
(3)
Read and mask group related signal.
Acknowledge and unmask group related signal (acknowledge should clear
aggregation status register from 0xfd back to 0xff).
(4)
Re-schedule work queue for the immediate execution.
(5)
Enter mlxreg_hotplug_work_handler due to re-scheduling.
Aggregation status is changed from previous 0xfd to 0xff.
Go over steps (2) - (5) and in case no new signal assertion
is detected - unmask aggregation interrupts.
The possible race could happen in case new signal from the same group is
asserted after step (3) and prior step (5). In such case aggregation
status will change back from 0xff to 0xfd and the value read from the
aggregation status register will be the same as a value saved in
aggr_cache. As a result the handler will not traverse down and signal
will stay unhandled.
Example of faulty flow:
The signal routing flow is as following (f.e. for of FANi removing):
- FAN status and event registers related bit is changed;
-- intermediate aggregation status register is changed;
--- top aggregation status register is changed;
---- interrupt routed to CPU and interrupt handler is invoked.
When interrupt handler is invoked it follows the next simple logic (f.e
FAN3 is removed):
(a1) mask top aggregation interrupt mask register;
(a2) read top aggregation interrupt status register and test to which
underling group belongs a signal (FANs in this case and is changed
from 0xff to 0xfb and 0xfb is saved as a last status value);
(b1) mask FANs interrupt mask register;
(b2) read FANs status register and test which FAN has been changed
FAN3 in this example);
(c1) perform relevant action;
<--------------- (FAN2 is removed at this point)
(b3) clear FANs interrupt event register to acknowledge FAN3 signal;
(b4) unmask FANs interrupt mask register
(a3) unmask top aggregation interrupt mask register;
An interrupt handler is invoked, since FAN2 interrupt is not acknowledge.
It should set top aggregation interrupt status register bit 6 (0xfb).
In step (a2)
(a2) read top aggregation interrupt and comparing it with saved value
does not show change (same 0xfb) and after (a2) execution jumps to
(a3) and signal leaved unhandled
The fix will enforce handler to traverse down in case the signal is
received, but signal assertion is not detected.
Fixes: 304887041d95 ("platform/x86: Introduce support for Mellanox hotplug driver")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Add missing description of dev, regmap, dwork_irq, after_probe in struct
mlxreg_hotplug_priv_data.
Remove dwork field from the structure mlxreg_hotplug_priv_data itself and
for the descriptions, since it is not used.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
mlx-platform does not provide a bus number to i2c-mlxcpld, assuming it
is always one. On some x86 systems, other i2c drivers may probe before
i2c-mlxcpld, causing bus one to be busy.
Make mlx-platform determine which adapter number is free prior to
activating i2c-mlxpld, adjusting the mux base numbers accordingly.
Update the mlxreg-hotplug pdata similarly.
This adds an explicit mlx-platform build dependency on I2C, update the
Kconfig accordingly. Add the missing REGMAP dependency while we're at
it.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
[dvhart: Rewrite commit message more concisely]
[dvhart: Add build dependencies]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Change the first input parameter in mlxreg_hotplug_device_create to the
pointer to mlxreg_hotplug private data in order to use the fields from
the private data structure.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
[dvhart: Cleaned up commit message]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
mlx-platform activates i2c-mux-reg, which creates buses needed by
mlxreg-hotplug. If the mlxreg-hotplug probe runs before the i2c-mux-reg
probe completes, it may attempt to connect a device to an adapter number
that has not been created yet, and fail.
Make mlx-platform driver record the highest bus number in mlxreg-hotplug
platform data and defer mlxreg-hotplug probe until all the buses are
created.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
[dvhart: rewrite commit message more concisely]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
With gcc-4.1.2:
drivers/platform/mellanox/mlxreg-hotplug.c: In function ‘mlxreg_hotplug_health_work_helper’:
drivers/platform/mellanox/mlxreg-hotplug.c:347: warning: ‘ret’ is used uninitialized in this function
Indeed, if mlxreg_core_item.count is zero, ret is used uninitialized.
While this is unlikely to happen (it is set to ARRAY_SIZE(...) in x86
board files), this is done in another source file, so fix this by
preinitializing ret to zero.
Fixes: c6acad68eb2dbffd ("platform/mellanox: mlxreg-hotplug: Modify to use a regmap interface")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Verify before creation of hotplug device if the associated adapter number
is negative. It could be in case hotplug event is not associated with
hotplug device.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Add ARM in addition to X86 as supported architectures in the Mellanox
Hotplug Platform driver Kconfig entry.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
[dvhart: rewrite commit message]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Restructure mlxreg header for unification of hotplug item definitions.
Unify hotplug items to allow any kind of item (power controller, fan
eeprom, psu eeprom, asic health) in common way.
Use a hardware independent regmap interface, enabling the support of
hotplug events over programmable devices attached to different bus
types, such as I2C, LPC, or SPI. Add a device node to the
mlxreg_core_data structure.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[dvhart: spelling corrections, refactor device node introduction]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Move the mlxreg_hotplug_device_create and _destroy functions up with the
related attribute functions. No functional changes.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[dvhart: refactored commit into smaller functional changes]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Use Linux convention of nr instead of bus for i2c adapter number.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[dvhart: refactored commit into smaller functional changes]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
The driver does not make use of anything defined in wait.h.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[dvhart: refactor into smaller functional changes, leave spinlock.h]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
In preparation for making the hotplug driver build for different
architectures, move mlxcpld-hotplug.c to platform/mellanox and the
header to include/linux/platform_data as mlxreg.h to reflect the new
interface changes to come.
Replace references to CPLD with REG throughout the files, consistent
with the new name.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[dvhart: update copyright, rewrite commit message]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
