| Age | Commit message (Collapse) | Author |
|---|
|
I got below build error with random config if CONFIG_PINCTRL_SAMSUNG=y &&
CONFIG_PINCTRL_EXYNOS5440=y.
Fix the build error by making pcfgs static.
LD drivers/pinctrl/built-in.o
drivers/pinctrl/pinctrl-exynos5440.o: In function `.LANCHOR0':
pinctrl-exynos5440.c:(.data+0x54): multiple definition of `pcfgs'
drivers/pinctrl/pinctrl-samsung.o:pinctrl-samsung.c:(.data+0x54): first defined here
make[2]: *** [drivers/pinctrl/built-in.o] Error 1
make[1]: *** [drivers/pinctrl] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
struct samsung_pin_bank does not have a member called reg_offset.
It should be pctl_offset instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform conversion patches from Olof Johansson:
"Here are more patches in the progression towards multiplatform, sparse
irq conversions in particular.
Tegra has a handful of cleanups and general groundwork, but is not
quite there yet on full enablement.
Platforms that are enabled through this branch are VT8500 and Zynq.
Note that i.MX was converted in one of the earlier cleanup branches as
well (before we started a separate topic for multiplatform). And both
new platforms for this merge window, sunxi and bcm, were merged with
multiplatform support enabled."
Fix up conflicts mostly as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: zynq: Remove all unused mach headers
ARM: zynq: add support for ARCH_MULTIPLATFORM
ARM: zynq: make use of debug_ll_io_init()
ARM: zynq: remove TTC early mapping
ARM: tegra: move debug-macro.S to include/debug
ARM: tegra: don't include iomap.h from debug-macro.S
ARM: tegra: decouple uncompress.h and debug-macro.S
ARM: tegra: simplify DEBUG_LL UART selection options
ARM: tegra: select SPARSE_IRQ
ARM: tegra: enhance timer.c to get IO address from device tree
ARM: tegra: enhance timer.c to get IRQ info from device tree
ARM: timer: fix checkpatch warnings
ARM: tegra: add TWD to device tree
ARM: tegra: define DT bindings for and instantiate RTC
ARM: tegra: define DT bindings for and instantiate timer
clocksource/mtu-nomadik: use apb_pclk
clk: ux500: Register mtu apb_pclocks
ARM: plat-nomadik: convert platforms to SPARSE_IRQ
mfd/db8500-prcmu: use the irq_domain_add_simple()
mfd/ab8500-core: use irq_domain_add_simple()
...
|
|
Pull ARM SoC device tree conversions and enablement from Olof Johansson:
"Continued device tree conversion and enablement across a number of
platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
smaller series as well.
ux500 has seen continued conversion for platforms. Several platforms
have seen pinctrl-via-devicetree conversions for simpler
multiplatform. Tegra is adding data for new devices/drivers, and
Exynos has a bunch of new bindings and devices added as well.
So, pretty much the same progression in the right direction as the
last few releases."
Fix up conflicts as per Olof.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (185 commits)
ARM: ux500: Rename dbx500 cpufreq code to be more generic
ARM: dts: add missing ux500 device trees
ARM: ux500: Stop registering the PCM driver from platform code
ARM: ux500: Move board specific GPIO info out to subordinate DTS files
ARM: ux500: Disable the MMCI gpio-regulator by default
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
...
|
|
Pull ARM SoC updates from Olof Johansson:
"This contains the bulk of new SoC development for this merge window.
Two new platforms have been added, the sunxi platforms (Allwinner A1x
SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
series of ARMv7 platforms from them, where the hope is that we can
keep the platform code generic enough to have them all share one mach
directory. The new Broadcom platform is contributed by Christian
Daudt.
Highbank has grown support for Calxeda's next generation of hardware,
ECX-2000.
clps711x has seen a lot of cleanup from Alexander Shiyan, and he's
also taken on maintainership of the platform.
Beyond this there has been a bunch of work from a number of people on
converting more platforms to IRQ domains, pinctrl conversion, cleanup
and general feature enablement across most of the active platforms."
Fix up trivial conflicts as per Olof.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (174 commits)
mfd: vexpress-sysreg: Remove LEDs code
irqchip: irq-sunxi: Add terminating entry for sunxi_irq_dt_ids
clocksource: sunxi_timer: Add terminating entry for sunxi_timer_dt_ids
irq: versatile: delete dangling variable
ARM: sunxi: add missing include for mdelay()
ARM: EXYNOS: Avoid early use of of_machine_is_compatible()
ARM: dts: add node for PL330 MDMA1 controller for exynos4
ARM: EXYNOS: Add support for secondary CPU bring-up on Exynos4412
ARM: EXYNOS: add UART3 to DEBUG_LL ports
ARM: S3C24XX: Add clkdev entry for camif-upll clock
ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers
ARM: sunxi: Add missing sun4i.dtsi file
pinctrl: samsung: Do not initialise statics to 0
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"These are the first and major pinctrl changes for the v3.8 merge
cycle. Some of this is used as merge base for other trees so I better
be early on the trigger.
As can be seen from the diffstat the major changes are:
- A big conversion of the AT91 pinctrl driver and the associated ACKed
platform changes under arch/arm/max-at91 and its device trees. This
has been coordinated with the AT91 maintainers to go in through the
pinctrl tree.
- A larger chunk of changes to the SPEAr drivers and the addition of
the "plgpio" driver for the SPEAr as well.
- The removal of the remnants of the Nomadik driver from the arch/arm
tree and fusion of that into the Nomadik driver and platform data
header files.
- Some local movement in the Marvell MVEBU drivers, these now have
their own subdirectory.
- The addition of a chunk of code to gpiolib under drivers/gpio to
register gpio-to-pin range mappings from the GPIO side of things.
This has been requested by Grant Likely and is now implemented, it
is particularly useful for device tree work.
Then we have incremental updates all over the place, many of these are
cleanups and fixes from Axel Lin who has done a great job of removing
minor mistakes and compilation annoyances."
* tag 'pinctrl-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (114 commits)
ARM: mmp: select PINCTRL for ARCH_MMP
pinctrl: Drop selecting PINCONF for MMP2, PXA168 and PXA910
pinctrl: pinctrl-single: Fix error check condition
pinctrl: SPEAr: Update error check for unsigned variables
gpiolib: Fix use after free in gpiochip_add_pin_range
gpiolib: rename pin range arguments
pinctrl: single: support gpio request and free
pinctrl: generic: add input schmitt disable parameter
pinctrl/u300/coh901: stop spawning pinctrl from GPIO
pinctrl/u300/coh901: let the gpio_chip register the range
pinctrl: add function to retrieve range from pin
gpiolib: return any error code from range creation
pinctrl: make range registration defer properly
gpiolib: rename find_pinctrl_*
gpiolib: let gpiochip_add_pin_range() specify offset
ARM: at91: pm9g45: add mmc support
ARM: at91: Animeo IP: add mmc support
ARM: at91: dt: add mmc pinctrl for Atmel reference boards
ARM: at91: dt: at91sam9: add mmc pinctrl support
ARM: at91/dts: add nodes for atmel hsmci controllers for atmel boards
...
|
|
These drivers do not need to select PINCONF.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
From Kukjin Kim:
* 'next/pinctrl-samsung-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
pinctrl: samsung: Do not initialise statics to 0
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option so __devinitconst is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Barry Song <baohua.song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
into next/dt
From Jason Cooper:
orion dt for v3.8
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
* tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux: (211 commits)
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
ARM: Kirkwood: Convert dnskw to pinctrl
ARM: Kirkwood: Convert iConnect to pinctrl.
ARM: Kirkwood: Convert TS219 to pinctrl.
ARM: Kirkwood: Add DTSI files for pinctrl
ARM: Kirkwood: Make use of mvebu pincltl and gpio drivers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
From Kukjin Kim:
This is adding support for exynos5440, including Quad ARM Cortex-A15
cores and its reference board SSDK5440.
Note, at this moment, just enabled minimal system part for initial kernel
boot and pinctrl driver.
* 'next/soc-exynos5440' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add pin controller node for Samsung EXYNOS5440 SoC
pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC
ARM: dts: add initial dts file for EXYNOS5440, SSDK5440
ARM: EXYNOS: add support for EXYNOS5440 SoC
Add/add conflict in arch/arm/boot/dts/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The Marvell 98DX412x SoC embed a kirkwood variant that does not have
pinctrl support yet. Even though this kirkwood is very similar to the
88f6281, on the MPP front a lot of pins are not available. That's why a
new kirkwood pinctrl variant is needed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
When setting audio1 pinmux the bits in the corresponding registers
are not cleared. This fix first clears all bits and then sets the
required bits according to the selected function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
There has been a change in readl/writel to require registers
addresses marked as IOMEM(). This patch takes care of this and
also replaces ORing address offsets with adding them.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Static variables are initialised to 0 by GCC.
Fixes the following checkpatch error:
ERROR: do not initialise statics to 0 or NULL
FILE: pinctrl/pinctrl-samsung.c:50:
static unsigned int pin_base = 0;
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
*map should be tested for NULL instead of map.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Checking '< 0' for unsigned variables always returns false. For error
codes, use IS_ERR_VALUE() instead.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a new pinctrl driver for Samsung EXYNOS5440 SoC. The pin controller
module in EXYNOS5440 is different from the pin controller found on other
Samsung SoC. Hence, the pin controller driver for EXYNOS5440 SoC is
independent of the Samsung pinctrl framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
Here is Samsung DT for v3.8 and this is including DT for EXYNOS4X12
SoC, SMDK4412 board, pinctrl for exynos4x12, TMU, MFC, SATA and SATA
PHY.
As I commented on [4/7], this branch merged pinctrl/samsung to support
pinctrl for exynos4x12 without useless merge conflicts.
* 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (32 commits)
ARM: EXYNOS: DT Support for SATA and SATA PHY
ARM: dts: Remove broken-voltage property from sdhci node for exynos4210-trats
ARM: dts: Add node for touchscreen for exynos4210-trats
ARM: dts: Add node for touchscreen voltage regulator for exynos4210-trats
ARM: dts: Add node for i2c3 bus for exynos4210-trats
ARM: dts: Add nodes for GPIO keys available on Trats
ARM: dts: Update for pinctrl-samsung driver for exynos4210-trats
ARM: dts: Add nodes for pin controllers for exynos4x12
pinctrl: samsung: Add support for EXYNOS4X12
gpio: samsung: Skip registration if pinctrl driver is present on EXYNOS4X12
ARM: EXYNOS: Skip wakeup-int setup if pinctrl driver is used on EXYNOS4X12
ARM: dts: add board dts file for EXYNOS4412 based SMDK board
ARM: dts: Add support for EXYNOS4X12 SoCs
ARM: EXYNOS: Add devicetree node for TMU driver for exynos5
ARM: EXYNOS: Add devicetree node for TMU driver for exynos4
ARM: EXYNOS: Add MFC device tree support
ARM: dts: Enable serial controllers on Origen and SMDKV310
Documentation: Update samsung-pinctrl device tree bindings documentation
pinctrl: samsung: Add GPIO to IRQ translation
pinctrl: exynos: Set pin function to EINT in irq_set_type of wake-up EINT
...
Add/add conflicts in:
arch/arm/boot/dts/exynos5250-smdk5250.dts
arch/arm/boot/dts/exynos5250.dtsi
arch/arm/mach-exynos/mach-exynos5-dt.c
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
From Kukjin Kim:
Here is Samsung DT for v3.8 and this is including DT for EXYNOS4X12
SoC, SMDK4412 board, pinctrl for exynos4x12, TMU, MFC, SATA and SATA
PHY.
As I commented on [4/7], this branch merged pinctrl/samsung to support
pinctrl for exynos4x12 without useless merge conflicts.
* samsung/pinctrl:
pinctrl: samsung: Update error check for unsigned variables
pinctrl: samsung: Add support for EXYNOS4X12
Documentation: Update samsung-pinctrl device tree bindings documentation
pinctrl: samsung: Add GPIO to IRQ translation
pinctrl: exynos: Set pin function to EINT in irq_set_type of wake-up EINT
pinctrl: samsung: Use per-bank IRQ domain for wake-up interrupts
pinctrl: samsung: Use one GPIO chip per pin bank
pinctrl: exynos: Use one IRQ domain per pin bank
pinctrl: samsung: Include bank-specific eint offset in bank struct
pinctrl: samsung: Hold pointer to driver data in bank struct
pinctrl: samsung: Match pin banks with their device nodes
ARM: dts: exynos4210-pinctrl: Add nodes for pin banks
pinctrl: samsung: Distinguish between pin group and bank nodes
pinctrl: samsung: Remove static pin enumerations
pinctrl: samsung: Assing pin numbers dynamically
pinctrl: samsung: Do not pass gpio_chip to pin_to_reg_bank
pinctrl: samsung: Detect and handle unsupported configuration types
|
|
|
|
Marvell's PXA/MMP silicon also match the behavior of pinctrl-single.
Each pin binds to one register. A lot of pins could be configured
as gpio.
GPIO range is defined as a child node of pinmux in .dtsi file. If those
pins are with the same gpio function configuration in the pinmux
register, they could be defined in the same GPIO range. For this new
child node, two properties are used.
reg = <the start of pinmux register in range, size of range>
pinctrl-single,gpio: <gpio base in range, the gpio function of the range
in the pinmux register>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In Marvell PXA/MMP silicons, input schmitt disable value is 0x40, not 0.
So append new config parameter -- input schmitt disable.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Let's stop spawning the pinctrl driver from the GPIO driver,
we have these two mechanisms broken apart now, and they can
each probe in isolation. If the GPIO driver cannot find its
pin controller (pinctrl-u300), the pin controller core will
tell it to defer probing.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Instead of having the pinctrl driver register the GPIO range
for the gpio_chip, making it necessary to instantiate the
pin controller from the GPIO driver and pass the GPIO chip as
platform data, now let the GPIO chip driver register it's own
ranges and have the pinctrl driver look up the GPIO chip from
the pinctrl core as necessary.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a function to the pinctrl core to retrieve the GPIO
range associated with a certain pin for a certain controller.
This is needed when a pinctrl driver want to look up the
corresponding struct gpio_chip for a certain pin. As the
GPIO drivers can now create these ranges themselves, the
pinctrl driver no longer knows about all its associated GPIO
chips.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This makes the pinctrl_find_and_add_gpio_range() return
-EPROBE_DEFER if the range hosting pin controller cannot be
located. We may assume that the common case for why adding a
range fails is that the targe pin controller device has not
probed yet.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Rename the function find_pinctrl_and_add_gpio_range()
to pinctrl_find_and_add_gpio_range() so as to be consistent
with the rest of the functions.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
http://github.com/at91linux/linux-at91 into at91
|
|
Checking '< 0' for unsigned variables always returns false. For error
codes, use IS_ERR_VALUE() instead.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch extends the driver with any necessary SoC-specific
definitions to support EXYNOS4X12 SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
|
|
option support
add :
set_deglitch: enable/disable deglitch
set_debounce: enable/disable debounce
set_pulldown: enable/disable pulldown
disable_schmitt_trig: disable schmitt trigger
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
They are not referenced outside of this file, make them static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
of_match_device() may return NULL.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Dump pinmux register value, not only function part in the pinmux
register.
Also fix the issue on caluclating pin offset. The last parameter
should be pin number, not register offset.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
SPEAr SoC's don't do anything in clk_prepare() of plgpio driver,
so there is no need to call this routine multiple times. Just
call it once at probe.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This driver allows clk_get() failure, and still work without it.
This patch adds !IS_ERR(plgpio->clk) checking in plgpio_request() error path
so we only call clk_disable_unprepare() if clk_prepare_enable() is called.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently get_gpio_pingroup() may return NULL or ERR_PTR(-EINVAL) when
no gpio_pingroup found. The caller in gpio_request_endisable() only
checks if the return value is NULL. Return ERR_PTR(-EINVAL) for
get_gpio_pingroup() causes problem and seems not necessary.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Return -ENOMEM instead of 0 if irq_domain_add_linear fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Current code does not work if count > 1, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Current code sets "pin_reg = &info->pin_regs[i];" in each loop iteration,
so in the case of no-match, pin_reg is not NULL.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The main samsung pinctrl module references the specific exynos4210
pinctrl driver, which selects the main driver in Kconfig.
Making the main driver a silent "bool" option avoid this potential
build error if CONFIG_PINCTRL_SAMSUNG=y && CONFIG_PINCTRL_EXYNOS4=n:
drivers/built-in.o:(.rodata+0x4e4): undefined reference to `exynos4210_pin_ctrl'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
They are not referenced outside of this file, make them static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The clkout group is split into groups clkout1 and clkout2
which allows pins cklkout1 and clkout2 to be muxed
separately.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
