| Age | Commit message (Collapse) | Author |
|---|
|
When merging A20 pinctrl support to A10 pinctrl driver, the I2C function
of PI3 is wrongly written as "i2c3" (it should be "i2c4").
Fix this typo.
Fixes: cad4e209c102 ("pinctrl: sunxi: add support of R40 to A10 pinctrl driver")
Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Old pinctrl drivers will need to disable strict mode for various reasons,
among which:
- Some DT will still have a pinctrl group for each GPIO used, which will
be rejected by pin_request. While we could remove those nodes, we still
have to deal with old DTs.
- Some GPIOs on these boards need to have their pin configuration changed
(for bias or current), and there's no clear migration path
Let's disable the strict mode on those SoCs so that there's no breakage.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
R40 is said to be an upgrade of A20, and its pin configuration is also
similar to A20 (and thus similar to A10).
Add support for R40 to the A10 pinctrl driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PH16 pin has a function with mux id 0x5, which is the DET pin of the
"sim" (smart card reader) IP block.
This function is missing in old versions of A10/A20 SoCs' datasheets and
user manuals, so it's also missing in the old drivers. The newest A10
Datasheet V1.70 and A20 Datasheet V1.41 contain this pin function, and
it's discovered during implementing R40 pinctrl driver.
Add it to the driver. As we now merged A20 pinctrl driver to the A10
one, we need to only fix the A10 driver now.
Fixes: f2821b1ca3a2 ("pinctrl: sunxi: Move Allwinner A10 pinctrl
driver to a driver of its own")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As A20 is designed as a pin-compatible upgrade of A10, their pin
controller are very similar, and can share one driver.
Add A20 support to the A10 driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get essentially the same change, so they are handled in batch.
Changes are (1) use builtin_platform_driver, (2) use init.h header
(3) delete module_exit related code, (4) delete MODULE_DEVICE_TABLE,
and (5) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We do delete the MODULE_LICENSE etc. tags since all that information
is already contained at the top of each file in the comments.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Hongzhou Yang <hongzhou.yang@mediatek.com>
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Vishnu Patekar <vishnupatekar0510@gmail.com>
Cc: Mylene Josserand <mylene.josserand@free-electrons.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pincontrol updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.1 development
cycle. Nothing really exciting this time: we basically added a few
new drivers and subdrivers and stabilized them in linux-next. Some
cleanups too. With sunrisepoint Intel has a real fine fully featured
pin control driver for contemporary hardware, and the AMD driver is
also for large deployments. Most of the others are ARM devices.
New drivers:
- Intel Sunrisepoint
- AMD KERNCZ GPIO
- Broadcom Cygnus IOMUX
New subdrivers:
- Marvell MVEBU Armada 39x SoCs
- Samsung Exynos 5433
- nVidia Tegra 210
- Mediatek MT8135
- Mediatek MT8173
- AMLogic Meson8b
- Qualcomm PM8916
On top of this cleanups and development history for the above drivers
as issues were fixed after merging"
* tag 'pinctrl-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (71 commits)
pinctrl: sirf: move sgpio lock into state container
pinctrl: Add support for PM8916 GPIO's and MPP's
pinctrl: bcm2835: Fix support for threaded level triggered IRQs
sh-pfc: r8a7790: add EtherAVB pin groups
pinctrl: Document "function" + "pins" pinmux binding
pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support
pinctrl: fsl: imx: Check for 0 config register
pinctrl: Add support for Meson8b
documentation: Extend pinctrl docs for Meson8b
pinctrl: Cleanup Meson8 driver
Fix inconsistent spinlock of AMD GPIO driver which can be recognized by static analysis tool smatch. Declare constant Variables with Sparse's suggestion.
pinctrl: at91: convert __raw to endian agnostic IO
pinctrl: constify of_device_id array
pinctrl: pinconf-generic: add dt node names to error messages
pinctrl: pinconf-generic: scan also referenced phandle node
pinctrl: mvebu: add suspend/resume support to Armada XP pinctrl driver
pinctrl: st: Display pin's function when printing pinctrl debug information
pinctrl: st: Show correct pin direction also in GPIO mode
pinctrl: st: Supply a GPIO get_direction() call-back
pinctrl: st: Move st_get_pio_control() further up the source file
...
|
|
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On sun4i-a10, when GPIOs are configured as external interrupt the value for
them in the data register does not seem to get updated, so set their mux to
input (and restore afterwards) when reading the pin.
Missed edges seem to be buffered, so this does not introduce a race
condition.
I've also tested this on sun5i-a13 and sun7i-a20 and those do not seem to
be affected, the input value representation in the data register does seem
to correctly get updated to the actual pin value while in irq mode there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Declare in the description structure associated to the compatible the number of
interrupt banks the device has. For now, we're not doing anything with it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
