summaryrefslogtreecommitdiff
path: root/drivers/pinctrl/pinctrl-amd.c
AgeCommit message (Collapse)Author
2020-12-16Merge tag 'pinctrl-v5.11-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v5.11 kernel. Drivers, drivers and drivers. Not a single core change. Some new stuff, especially a bunch of new Intel, Qualcomm and Ocelot SoCs. As part of the modularization attempt, I applied one patch affecting the firmware subsystem as a functional (not syntactic/semantic) dependency and then it blew up in our face, so I had to revert it, bummer. It will come in later, through that subsystem, I guess. New drivers: - New driver for the Microchip Serial GPIO "SGPIO". - Qualcomm SM8250 LPASS (Low Power Audio Subsystem) GPIO driver. New subdrivers: - Intel Lakefield subdriver. - Intel Elkhart Lake subdriver. - Intel Alder Lake-S subdriver. - Qualcomm MSM8953 subdriver. - Qualcomm SDX55 subdriver. - Qualcomm SDX55 PMIC subdriver. - Ocelot Luton SoC subdriver. - Ocelot Serval SoC subdriver. Modularization: - The Meson driver can now be built as modules. - The Qualcomm driver(s) can now be built as modules. Incremental improvements: - The Intel driver now supports pin configuration for GPIO-related configurations. - A bunch of Renesas PFC drivers have been augmented with support for QSPI pins, groups and functions. - Non-critical fixes to the irq handling in the Allwinner Sunxi driver" * tag 'pinctrl-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits) pinctrl/spear: simplify the return expression of spear300_pinctrl_probe() pinctrl: mediatek: simplify the return expression of mtk_pinconf_bias_disable_set_rev1() dt-bindings: pinctrl: pinctrl-microchip-sgpio: Add irq support pinctrl: pinctrl-microchip-sgpio: Add irq support (for sparx5) pinctrl: qcom: Add sm8250 lpass lpi pinctrl driver dt-bindings: pinctrl: qcom: Add sm8250 lpass lpi pinctrl bindings pinctrl: qcom-pmic-gpio: Add support for pmx55 dt-bindings: pinctrl: qcom-pmic-gpio: Add pmx55 support pinctrl: pinctrl-microchip-sgpio: Mark some symbols with static keyword pinctrl: at91-pio4: Make PINCTRL_AT91PIO4 depend on HAS_IOMEM to fix build error pinctrl: mtk: Fix low level output voltage issue pinctrl: falcon: add missing put_device() call in pinctrl_falcon_probe() pinctrl: actions: pinctrl-s500: Constify s500_padinfo[] pinctrl: pinctrl-microchip-sgpio: Add OF config dependency pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO dt-bindings: pinctrl: Add bindings for pinctrl-microchip-sgpio driver pinctrl: at91-pio4: add support for fewer lines on last PIO bank pinctrl: sunxi: Always call chained_irq_{enter, exit} in sunxi_pinctrl_irq_handler pinctrl: sunxi: Mark the irq bank not found in sunxi_pinctrl_irq_handler() with WARN_ON pinctrl: sunxi: fix irq bank map for the Allwinner A100 pin controller ...
2020-12-04pinctrl: amd: remove debounce filter setting in IRQ type settingCoiby Xu
Debounce filter setting should be independent from IRQ type setting because according to the ACPI specs, there are separate arguments for specifying debounce timeout and IRQ type in GpioIo() and GpioInt(). Together with commit 06abe8291bc31839950f7d0362d9979edc88a666 ("pinctrl: amd: fix incorrect way to disable debounce filter") and Andy's patch "gpiolib: acpi: Take into account debounce settings" [1], this will fix broken touchpads for laptops whose BIOS set the debounce timeout to a relatively large value. For example, the BIOS of Lenovo AMD gaming laptops including Legion-5 15ARH05 (R7000), Legion-5P (R7000P) and IdeaPad Gaming 3 15ARH05, set the debounce timeout to 124.8ms. This led to the kernel receiving only ~7 HID reports per second from the Synaptics touchpad (MSFT0001:00 06CB:7F28). Existing touchpads like [2][3] are not troubled by this bug because the debounce timeout has been set to 0 by the BIOS before enabling the debounce filter in setting IRQ type. [1] https://lore.kernel.org/linux-gpio/20201111222008.39993-11-andriy.shevchenko@linux.intel.com/ 8dcb7a15a585 ("gpiolib: acpi: Take into account debounce settings") [2] https://github.com/Syniurge/i2c-amd-mp2/issues/11#issuecomment-721331582 [3] https://forum.manjaro.org/t/random-short-touchpad-freezes/30832/28 Signed-off-by: Coiby Xu <coiby.xu@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/linux-gpio/CAHp75VcwiGREBUJ0A06EEw-SyabqYsp%2Bdqs2DpSrhaY-2GVdAA%40mail.gmail.com/ BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1887190 Link: https://lore.kernel.org/r/20201125130320.311059-1-coiby.xu@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-11-10pinctrl: amd: print debounce filter info in debugfsCoiby Xu
Print the status of debounce filter as follows, $ cat /sys/kernel/debug/gpio pin129 interrupt is disabled | interrupt is masked | disable wakeup in S0i3 state | disable wakeup in S3 state | disable wakeup in S4/S5 state| input is high | pull-up is disabled | Pull-down is disabled | output is disabled | debouncing filter disabled | 0x50000 pin130 interrupt is disabled | interrupt is masked | disable wakeup in S0i3 state | disable wakeup in S3 state | disable wakeup in S4/S5 state | input is high | pull-up is disabled | Pull-down is disabled | output is disabled | debouncing filter (high) enabled | debouncing timeout is 124800 (us)| 0x503c8 Signed-off-by: Coiby Xu <coiby.xu@gmail.com> Link: https://lore.kernel.org/r/20201105231912.69527-4-coiby.xu@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-11-10pinctrl: amd: use higher precision for 512 RtcClkCoiby Xu
RTC is 32.768kHz thus 512 RtcClk equals 15625 usec. The documentation likely has dropped precision and that's why the driver mistakenly took the slightly deviated value. Cc: stable@vger.kernel.org Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com> Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com> Suggested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Coiby Xu <coiby.xu@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/linux-gpio/2f4706a1-502f-75f0-9596-cc25b4933b6c@redhat.com/ Link: https://lore.kernel.org/r/20201105231912.69527-3-coiby.xu@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-11-10pinctrl: amd: fix incorrect way to disable debounce filterCoiby Xu
The correct way to disable debounce filter is to clear bit 5 and 6 of the register. Cc: stable@vger.kerne.org Signed-off-by: Coiby Xu <coiby.xu@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Cc: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/linux-gpio/df2c008b-e7b5-4fdd-42ea-4d1c62b52139@redhat.com/ Link: https://lore.kernel.org/r/20201105231912.69527-2-coiby.xu@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-08-04pinctrl: amd: Use irqchip templateLinus Walleij
This makes the driver use the irqchip template to assign properties to the gpio_irq_chip instead of using the explicit call to gpiochip_irqchip_add(). The irqchip is instead added while adding the gpiochip. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Cc: Sandeep Singh <sandeep.singh@amd.com> Link: https://lore.kernel.org/r/20200722101545.144373-1-linus.walleij@linaro.org
2020-07-16pinctrl: pinctrl-amd: Do not define 'struct acpi_device_id' when !CONFIG_ACPILee Jones
Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI, 'struct amd_gpio_acpi_match' becomes defined but unused. Fixes the following W=1 kernel build warning(s): drivers/pinctrl/pinctrl-amd.c:959:36: warning: ‘amd_gpio_acpi_match’ defined but not used [-Wunused-const-variable=] 959 | static const struct acpi_device_id amd_gpio_acpi_match[] = { Signed-off-by: Lee Jones <lee.jones@linaro.org> Cc: Ken Xue <Ken.Xue@amd.com> Cc: "Wu, Jeff" <Jeff.Wu@amd.com> Cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Cc: Sundar S K <Shyam-sundar.S-k@amd.com> Link: https://lore.kernel.org/r/20200713144930.1034632-26-lee.jones@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-07-07pinctrl: amd: Honor IRQ trigger type requested by the callerFurquan Shaikh
This change drops the override in `amd_gpio_irq_set_type()` that ignores the IRQ trigger type settings from the caller. The device driver (caller) is in a better position to identify the right trigger type for the device based on the usage as well as the information exposed by the BIOS. There are instances where the device driver might want to configure the trigger type differently in different modes. An example of this is gpio-keys driver which configures IRQ type as trigger on both edges (to identify assert and deassert events) when in S0 and reconfigures the trigger type using the information provided by the BIOS when going into suspend to ensure that the wake happens on the required edge. This override in `amd_gpio_irq_set_type()` prevents the caller from being able to reconfigure trigger type once it is set either based on ACPI information or the type used by the first caller for IRQ on a given GPIO line. Without this change, pen-insert gpio key (used by garaged stylus on a Chromebook) works fine in S0 (i.e. insert and eject events are correctly identified), however, BIOS configuration for wake on only pen eject i.e. only-rising edge or only-falling edge is not honored. With this change, it was verified that pen-insert gpio key behavior is correct in both S0 and for wakeup from S3. Signed-off-by: Furquan Shaikh <furquan@google.com> Signed-off-by: Shyam Sundar S K<Shyam-sundar.S-k@amd.com> Link: https://lore.kernel.org/r/20200626211026.513520-1-furquan@google.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-02-21pinctrl: Use new GPIO_LINE_DIRECTIONMatti Vaittinen
Use newly added GPIO defines GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT instead of using hard-coded 1 and 0. Main benefit is to make it easier to see which values mean IN and which OUT. As a side effect this helps GPIO framework to change the direction defines to something else if ever needed. Please note that return value from get_direction call on pinctrl-axp209 driver was changed. Previously pinctrl-axp209 might have returned value 2 for direction INPUT. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Reported-by: kbuild test robot <lkp@intel.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Link: https://lore.kernel.org/r/20200214135712.GA14557@localhost.localdomain Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-01-06remove ioremap_nocache and devm_ioremap_nocacheChristoph Hellwig
ioremap has provided non-cached semantics by default since the Linux 2.6 days, so remove the additional ioremap_nocache interface. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Arnd Bergmann <arnd@arndb.de>
2019-11-04pinctrl: amd: fix __iomem annotation in amd_gpio_irq_handler()Ben Dooks (Codethink)
The regs pointer in amd_gpio_irq_handler() should have __iomem on it, so add that to fix the following sparse warnings: drivers/pinctrl/pinctrl-amd.c:555:14: warning: incorrect type in assignment (different address spaces) drivers/pinctrl/pinctrl-amd.c:555:14: expected unsigned int [usertype] *regs drivers/pinctrl/pinctrl-amd.c:555:14: got void [noderef] <asn:2> *base drivers/pinctrl/pinctrl-amd.c:563:34: warning: incorrect type in argument 1 (different address spaces) drivers/pinctrl/pinctrl-amd.c:563:34: expected void const volatile [noderef] <asn:2> *addr drivers/pinctrl/pinctrl-amd.c:563:34: got unsigned int [usertype] * drivers/pinctrl/pinctrl-amd.c:580:34: warning: incorrect type in argument 1 (different address spaces) drivers/pinctrl/pinctrl-amd.c:580:34: expected void const volatile [noderef] <asn:2> *addr drivers/pinctrl/pinctrl-amd.c:580:34: got unsigned int [usertype] * drivers/pinctrl/pinctrl-amd.c:587:25: warning: incorrect type in argument 2 (different address spaces) drivers/pinctrl/pinctrl-amd.c:587:25: expected void volatile [noderef] <asn:2> *addr drivers/pinctrl/pinctrl-amd.c:587:25: got unsigned int [usertype] * Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk> Link: https://lore.kernel.org/r/20191022151154.5986-1-ben.dooks@codethink.co.uk Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-08-23pinctrl: amd: disable spurious-firing GPIO IRQsDaniel Drake
When cold-booting Asus X434DA, GPIO 7 is found to be already configured as an interrupt, and the GPIO level is found to be in a state that causes the interrupt to fire. As soon as pinctrl-amd probes, this interrupt fires and invokes amd_gpio_irq_handler(). The IRQ is acked, but no GPIO-IRQ handler was invoked, so the GPIO level being unchanged just causes another interrupt to fire again immediately after. This results in an interrupt storm causing this platform to hang during boot, right after pinctrl-amd is probed. Detect this situation and disable the GPIO interrupt when this happens. This enables the affected platform to boot as normal. GPIO 7 actually is the I2C touchpad interrupt line, and later on, i2c-multitouch loads and re-enables this interrupt when it is ready to handle it. Instead of this approach, I considered disabling all GPIO interrupts at probe time, however that seems a little risky, and I also confirmed that Windows does not seem to have this behaviour: the same 41 GPIO IRQs are enabled under both Linux and Windows, which is a far larger collection than the GPIOs referenced by the DSDT on this platform. Signed-off-by: Daniel Drake <drake@endlessm.com> Link: https://lore.kernel.org/r/20190814090540.7152-1-drake@endlessm.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-08-05pinctrl: Remove dev_err() usage after platform_get_irq()Stephen Boyd
We don't need dev_err() messages when platform_get_irq() fails now that platform_get_irq() prints an error message itself when something goes wrong. Let's remove these prints with a simple semantic patch. // <smpl> @@ expression ret; struct platform_device *E; @@ ret = ( platform_get_irq(E, ...) | platform_get_irq_byname(E, ...) ); if ( \( ret < 0 \| ret <= 0 \) ) { ( -if (ret != -EPROBE_DEFER) -{ ... -dev_err(...); -... } | ... -dev_err(...); ) ... } // </smpl> While we're here, remove braces on if statements that only have one statement (manually). Cc: Linus Walleij <linus.walleij@linaro.org> Cc: linux-gpio@vger.kernel.org Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20190730181557.90391-34-swboyd@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-06-05treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 422Thomas Gleixner
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms and conditions of the gnu general public license version 2 as published by the free software foundation extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 101 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-08pinctrl: Added IRQF_SHARED flag for amd-pinctrl driverSandeep Singh
Some of the AMD reference boards used single GPIO line for multiple devices. So added IRQF_SHARED flag in amd pinctrl driver. Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-01-11pinctrl/amd: fix typoMatteo Croce
Fix spelling mistake: "lenght" -> "length" Signed-off-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-05pinctrl: pinctrl-amd: simplify getting .driver_dataWolfram Sang
We should get 'driver_data' from 'struct device' directly. Going via platform_device is an unneeded step back and forth. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-10-01Merge tag 'v4.19-rc6' into develLinus Walleij
This is the 4.19-rc6 release I needed to merge this in because of extensive conflicts in the MSM and Intel pin control drivers. I know how to resolve them, so let's do it like this. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-25pinctrl/amd: poll InterruptEnable bits in amd_gpio_irq_set_typeDaniel Kurtz
From the AMD BKDG, if WAKE_INT_MASTER_REG.MaskStsEn is set, a software write to the debounce registers of *any* gpio will block wake/interrupt status generation for *all* gpios for a length of time that depends on WAKE_INT_MASTER_REG.MaskStsLength[11:0]. During this period the Interrupt Delivery bit (INTERRUPT_ENABLE) will read as 0. In commit 4c1de0414a1340 ("pinctrl/amd: poll InterruptEnable bits in enable_irq") we tried to fix this same "gpio Interrupts are blocked immediately after writing debounce registers" problem, but incorrectly assumed it only affected the gpio whose debounce was being configured and not ALL gpios. To solve this for all gpios, we move the polling loop from amd_gpio_irq_enable() to amd_gpio_irq_set_type(), while holding the gpio spinlock. This ensures that another gpio operation (e.g. amd_gpio_irq_unmask()) can read a temporarily disabled IRQ and incorrectly disable it while trying to modify some other register bits. Fixes: 4c1de0414a1340 pinctrl/amd: poll InterruptEnable bits in enable_irq Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-14pinctrl: Include <linux/gpio/driver.h> nothing elseLinus Walleij
These drivers are GPIO drivers, and the do not need to use the legacy header in <linux/gpio.h>, go directly for <linux/gpio/driver.h> instead. Replace any use of GPIOF_* with 0/1, these flags are for consumers, not drivers. Get rid of a few gpio_to_irq() users that was littering around the place, use local callbacks or avoid using it at all. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-07-29pinctrl/amd: only handle irq if it is pending and unmaskedDaniel Kurtz
The AMD pinctrl driver demultiplexes GPIO interrupts and fires off their individual handlers. If one of these GPIO irqs is configured as a level interrupt, and its downstream handler is a threaded ONESHOT interrupt, the GPIO interrupt source is masked by handle_level_irq() until the eventual return of the threaded irq handler. During this time the level GPIO interrupt status will still report as high until the actual gpio source is cleared - both in the individual GPIO interrupt status bit (INTERRUPT_STS_OFF) and in its corresponding "WAKE_INT_STATUS_REG" bit. Thus, if another GPIO interrupt occurs during this time, amd_gpio_irq_handler() will see that the (masked-and-not-yet-cleared) level irq is still pending and incorrectly call its handler again. To fix this, have amd_gpio_irq_handler() check for both interrupts status and mask before calling generic_handle_irq(). Note: Is it possible that this bug was the source of the interrupt storm on Ryzen when using chained interrupts before commit ba714a9c1dea85 ("pinctrl/amd: Use regular interrupt instead of chained")? Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-07-29pinctrl/amd: fix gpio irq level in debugfsDaniel Kurtz
According to the AMD BKDG, the GPIO ActiveLevel bits (10:9) map to: 00 Active High 01 Active Low 10 Active on both edges iff LevelTrig (bit 8) == 0 11 Reserved The current code has a bug where it interprets 00 => Active Low, and 01 => Active High. Fix the bug, restrict "Active on both" to just the edge trigger case, and refactor a bit to make the logic more readable. Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-26pinctrl/amd: poll InterruptEnable bits in enable_irqDaniel Kurtz
In certain cases interrupt enablement will be delayed relative to when the InterruptEnable bits are written. One example of this is when a GPIO's "debounce" logice is first enabled. After enabling debounce, there is a 900 us "warm up" period during which InterruptEnable[0] (bit 11) will read as 0 despite being written 1. During this time InterruptSts will not be updated, nor will interrupts be delivered, even if the GPIO's interrupt configuration has been written to the register. To work around this delay, poll the InterruptEnable bits after setting them to ensure interrupts have truly been enabled in hardware before returning from the irq_enable handler. Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-22pinctrl/amd: add get_direction handlerDaniel Kurtz
On boot, gpiochip_add_data() initializes the FLAG_IS_OUT bit in desc->flags iff its gpio_chip does not have ->direction_input() handler, else it is initialized to 0, which implies the GPIO is an "input". Later, the sysfs "direction" handler will use gpiod_get_direction() to get the current direction, but if no ->get_direction() handler is installed, the result will just be the current (initial) value of flags, which will always be OUT irregardless of the initial register value. Add a get_direction() handler to pinctrl-amd to fix this and always provide the correct value for direction. Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-16Merge tag 'pinctrl-v4.15-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v4.15 kernel cycle: Core: - The pin control Kconfig entry PINCTRL is now turned into a menuconfig option. This obviously has the implication of making the subsystem menu visible in menuconfig. This is happening because of two things: (a) Intel have started to deploy and depend on pin controllers in a way that is affecting users directly. This happens on the highly integrated laptop chipsets named after geographical places: baytrail, broxton, cannonlake, cedarfork, cherryview, denverton, geminilake, lewisburg, merrifield, sunrisepoint... It started a while back and now it is ever more evident that this is crucial infrastructure for x86 laptops and not an embedded obscurity anymore. Users need to be aware. (b) Pin control expanders on I2C and SPI that are arch-agnostic. Currently Semtech SX150X and Microchip MCP28x08 but more are expected. Users will have to be able to configure these in directly for their set-up. - Just go and select GPIOLIB now that we made sure that GPIOLIB is a very vanilla subsystem. Do not depend on it, if we need it, select it. - Exposing the pin control subsystem in menuconfig uncovered a bunch of obscure bugs that are now hopefully fixed, all more or less pertaining to Blackfin. - Unified namespace for cross-calls between pin control and GPIO. - New support for clock skew/delay generic DT bindings and generic pin config options for this. - Minor documentation improvements. Various: - The Renesas SH-PFC pin controller has evolved a lot. It seems Renesas are churning out new SoCs by the minute. - A bunch of non-critical fixes for the Rockchip driver. - Improve the use of library functions instead of open coding. - Support the MCP28018 variant in the MCP28x08 driver. - Static constifying" * tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits) pinctrl: gemini: Fix missing pad descriptions pinctrl: Add some depends on HAS_IOMEM pinctrl: samsung/s3c24xx: add CONFIG_OF dependency pinctrl: gemini: Fix GMAC groups pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support pinctrl: ti-iodelay: remove redundant unused variable dev pinctrl: max77620: Use common error handling code in max77620_pinconf_set() pinctrl: gemini: Implement clock skew/delay config pinctrl: gemini: Use generic DT parser pinctrl: Add skew-delay pin config and bindings pinctrl: armada-37xx: Add edge both type gpio irq support pinctrl: uniphier: remove eMMC hardware reset pin-mux pinctrl: rockchip: Add iomux-route switching support for rk3288 pinctrl: intel: Add Intel Cedar Fork PCH pin controller support pinctrl: intel: Make offset to interrupt status register configurable pinctrl: sunxi: Enforce the strict mode by default pinctrl: sunxi: Disable strict mode for old pinctrl drivers pinctrl: sunxi: Introduce the strict flag pinctrl: sh-pfc: Save/restore registers for PSCI system suspend pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description ...
2017-11-14Merge tag 'gpio-v4.15-1' of ↵Linus Torvalds
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO updates from Linus Walleij: "This is the bulk of GPIO changes for the v4.15 kernel cycle: Core: - Fix the semantics of raw GPIO to actually be raw. No inversion semantics as before, but also no open draining, and allow the raw operations to affect lines used for interrupts as the caller supposedly knows what they are doing if they are getting the big hammer. - Rewrote the __inner_function() notation calls to names that make more sense. I just find this kind of code disturbing. - Drop the .irq_base() field from the gpiochip since now all IRQs are mapped dynamically. This is nice. - Support for .get_multiple() in the core driver API. This allows us to read several GPIO lines with a single register read. This has high value for some usecases: it can be used to create oscilloscopes and signal analyzers and other things that rely on reading several lines at exactly the same instant. Also a generally nice optimization. This uses the new assign_bit() macro from the bitops lib that was ACKed by Andrew Morton and is implemented for two drivers, one of them being the generic MMIO driver so everyone using that will be able to benefit from this. - Do not allow requests of Open Drain and Open Source setting of a GPIO line simultaneously. If the hardware actually supports enabling both at the same time the electrical result would be disastrous. - A new interrupt chip core helper. This will be helpful to deal with "banked" GPIOs, which means GPIO controllers with several logical blocks of GPIO inside them. This is several gpiochips per device in the device model, in contrast to the case when there is a 1-to-1 relationship between a device and a gpiochip. New drivers: - Maxim MAX3191x industrial serializer, a very interesting piece of professional I/O hardware. - Uniphier GPIO driver. This is the GPIO block from the recent Socionext (ex Fujitsu and Panasonic) platform. - Tegra 186 driver. This is based on the new banked GPIO infrastructure. Other improvements: - Some documentation improvements. - Wakeup support for the DesignWare DWAPB GPIO controller. - Reset line support on the DesignWare DWAPB GPIO controller. - Several non-critical bug fixes and improvements for the Broadcom BRCMSTB driver. - Misc non-critical bug fixes like exotic errorpaths, removal of dead code etc. - Explicit comments on fall-through switch() statements" * tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits) gpio: tegra186: Remove tegra186_gpio_lock_class gpio: rcar: Add r8a77995 (R-Car D3) support pinctrl: bcm2835: Fix some merge fallout gpio: Fix undefined lock_dep_class gpio: Automatically add lockdep keys gpio: Introduce struct gpio_irq_chip.first gpio: Disambiguate struct gpio_irq_chip.nested gpio: Add Tegra186 support gpio: Export gpiochip_irq_{map,unmap}() gpio: Implement tighter IRQ chip integration gpio: Move lock_key into struct gpio_irq_chip gpio: Move irq_valid_mask into struct gpio_irq_chip gpio: Move irq_nested into struct gpio_irq_chip gpio: Move irq_chained_parent to struct gpio_irq_chip gpio: Move irq_default_type to struct gpio_irq_chip gpio: Move irq_handler to struct gpio_irq_chip gpio: Move irqdomain into struct gpio_irq_chip gpio: Move irqchip into struct gpio_irq_chip gpio: Introduce struct gpio_irq_chip pinctrl: armada-37xx: remove unused variable ...
2017-11-09Merge branch 'gpio-irqchip-rework' of /home/linus/linux-gpio into develLinus Walleij
2017-11-08gpio: Move irqdomain into struct gpio_irq_chipThierry Reding
In order to consolidate the multiple ways to associate an IRQ chip with a GPIO chip, move more fields into the new struct gpio_irq_chip. Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-10-19pinctrl/amd: fix masking of GPIO interruptsDaniel Drake
On Asus laptop models X505BA, X505BP, X542BA and X542BP, the i2c-hid touchpad (using a GPIO for interrupts) becomes unresponsive after a few minutes of usage, or after placing two fingers on the touchpad, which seems to have the effect of queuing up a large amount of input data to be transferred. When the touchpad is in unresponsive state, we observed that the GPIO level-triggered interrupt is still at it's active level, however the pinctrl-amd driver is not receiving/dispatching more interrupts at this point. After the initial interrupt arrives, amd_gpio_irq_mask() is called however we then see amd_gpio_irq_handler() being called repeatedly for the same irq; the interrupt mask is not taking effect because of the following sequence of events: - amd_gpio_irq_handler fires, reads and caches pin reg - amd_gpio_irq_handler calls generic_handle_irq() - During IRQ handling, amd_gpio_irq_mask() is called and modifies pin reg - amd_gpio_irq_handler clears interrupt by writing cached value The stale cached value written at the final stage undoes the masking. Fix this by re-reading the register before clearing the interrupt. I also spotted that the interrupt-clearing code can race against amd_gpio_irq_mask() / amd_gpio_irq_unmask(), so add locking there. Presumably this race was leading to the loss of interrupts. After these changes, the touchpad appears to be working fine. Signed-off-by: Daniel Drake <drake@endlessm.com> Acked-by: Shah, Nehal-bakulchandra <Nehal-Bakulchandra.shah@amd.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-09-21pinctrl/amd: make functions amd_gpio_suspend and amd_gpio_resume staticColin Ian King
The functions amd_gpio_suspend and amd_gpio_resume are local to the source and do not need to be in global scope, so make them static. Cleans up sparse warnings: symbol 'amd_gpio_suspend' was not declared. Should it be static? symbol 'amd_gpio_resume' was not declared. Should it be static? Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-09-12pinctrl/amd: save pin registers over suspend/resumeDaniel Drake
The touchpad in the Asus laptop models X505BA/BP and X542BA/BP is unresponsive after suspend/resume. The following error appears during resume: i2c_hid i2c-ELAN1300:00: failed to reset device. The problem here is that i2c_hid does not notice the interrupt being generated at this point, because the GPIO is no longer configured for interrupts. Fix this by saving pinctrl-amd pin registers during suspend and restoring them at resume time. Based on code from pinctrl-intel. Cc: stable@vger.kernel.org Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-22pinctrl: amd: fix error return code in amd_gpio_probe()Gustavo A. R. Silva
platform_get_irq() returns an error code, but the pinctrl-amd driver ignores it and always returns -EINVAL. This is not correct and, prevents -EPROBE_DEFER from being propagated properly. Print and propagate the return value of platform_get_irq on failure. This issue was detected with the help of Coccinelle. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-06-29Merge tag 'v4.12-rc7' into develLinus Walleij
Linux 4.12-rc7
2017-06-09pinctrl/amd: Use regular interrupt instead of chainedThomas Gleixner
The AMD pinctrl driver uses a chained interrupt to demultiplex the GPIO interrupts. Kevin Vandeventer reported, that his new AMD Ryzen locks up hard on boot when the AMD pinctrl driver is initialized. The reason is an interrupt storm. It's not clear whether that's caused by hardware or firmware or both. Using chained interrupts on X86 is a dangerous endavour. If a system is misconfigured or the hardware buggy there is no safety net to catch an interrupt storm. Convert the driver to use a regular interrupt for the demultiplex handler. This allows the interrupt storm detector to catch the malfunction and lets the system boot up. This should be backported to stable because it's likely that more users run into this problem as the AMD Ryzen machines are spreading. Reported-by: Kevin Vandeventer Link: https://bugzilla.suse.com/show_bug.cgi?id=1034261 Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-22pinctrl/amd: Update contact information for AMD pinctrl/amdShyam Sundar S K
Updating the point of contact for AMD GPIO driver. Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Cc: Ken Xue <Ken.Xue@amd.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-02Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial Pull trivial tree updates from Jiri Kosina. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: tty: fix comment for __tty_alloc_driver() init/main: properly align the multi-line comment init/main: Fix double "the" in comment Fix dead URLs to ftp.kernel.org drivers: Clean up duplicated email address treewide: Fix typo in xml/driver-api/basics.xml tools/testing/selftests/powerpc: remove redundant CFLAGS in Makefile: "-Wall -O2 -Wall" -> "-O2 -Wall" selftests/timers: Spelling s/privledges/privileges/ HID: picoLCD: Spelling s/REPORT_WRTIE_MEMORY/REPORT_WRITE_MEMORY/ net: phy: dp83848: Fix Typo UBI: Fix typos Documentation: ftrace.txt: Correct nice value of 120 priority net: fec: Fix typo in error msg and comment treewide: Fix typos in printk
2017-03-24treewide: Fix typos in printkMasanari Iida
This patch fix some spelling typos found in printk. [jkosina@suse.cz: drop arch/arm64/kernel/hibernate.c that was already in place] Signed-off-by: Masanari Iida <standby24x7@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2017-03-16pinctrl: amd: make use of raw_spinlock variantsJulia Cartwright
The amd pinctrl drivers currently implement an irq_chip for handling interrupts; due to how irq_chip handling is done, it's necessary for the irq_chip methods to be invoked from hardirq context, even on a a real-time kernel. Because the spinlock_t type becomes a "sleeping" spinlock w/ RT kernels, it is not suitable to be used with irq_chips. A quick audit of the operations under the lock reveal that they do only minimal, bounded work, and are therefore safe to do under a raw spinlock. Signed-off-by: Julia Cartwright <julia@ni.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-01-30Merge tag 'v4.10-rc6' into develLinus Walleij
Linux 4.10-rc6 Resolved conflicts in: drivers/pinctrl/pinctrl-amd.c drivers/pinctrl/samsung/pinctrl-exynos.c
2017-01-26Merge branch 'ib-pinctrl-genprops' into develLinus Walleij
2017-01-26pinctrl / gpio: Introduce .set_config() callback for GPIO chipsMika Westerberg
Currently we already have two pin configuration related callbacks available for GPIO chips .set_single_ended() and .set_debounce(). In future we expect to have even more, which does not scale well if we need to add yet another callback to the GPIO chip structure for each possible configuration parameter. Better solution is to reuse what we already have available in the generic pinconf. To support this, we introduce a new .set_config() callback for GPIO chips. The callback takes a single packed pin configuration value as parameter. This can then be extended easily beyond what is currently supported by just adding new types to the generic pinconf enum. If the GPIO driver is backed up by a pinctrl driver the GPIO driver can just assign gpiochip_generic_config() (introduced in this patch) to .set_config and that will take care configuration requests are directed to the pinctrl driver. We then convert the existing drivers over .set_config() and finally remove the .set_single_ended() and .set_debounce() callbacks. Suggested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-01-19pinctrl/amd: Drop pinctrl_unregister for devm_ registered deviceWei Yongjun
It's not necessary to unregister pin controller device registered with devm_pinctrl_register() and using pinctrl_unregister() leads to a double free. Fixes: 3bfd44306c65 ("pinctrl: amd: Add support for additional GPIO") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-01-12pinctrl: amd: avoid maybe-uninitalized warningArnd Bergmann
Since gpio_dev->hwbank_num is now a variable, the compiler cannot figure out if pin_num is initialized at all: drivers/pinctrl/pinctrl-amd.c: In function 'amd_gpio_dbg_show': drivers/pinctrl/pinctrl-amd.c:210:3: warning: 'pin_num' may be used uninitialized in this function [-Wmaybe-uninitialized] for (; i < pin_num; i++) { ^~~ drivers/pinctrl/pinctrl-amd.c:172:21: warning: 'i' may be used uninitialized in this function [-Wmaybe-uninitialized] This adds a 'default' statement to make that case well-defined. Fixes: 3bfd44306c65 ("pinctrl: amd: Add support for additional GPIO") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-01-11pinctrl/amd: white space cleanups in amd_gpio_dbg_show()Dan Carpenter
We accidentally deleted two tabs from the first line, but even with that fixed the conditions were not really kernel style. Put the && at the end of the line so we can align the condition clauses. Also add spaces around the "+" operator. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-01-03pinctrl: amd: fix compilation warningLinus Walleij
3bfd44306c65 ("pinctrl: amd: Add support for additional GPIO") created the following warning: drivers/pinctrl/pinctrl-amd.c: In function 'amd_gpio_dbg_show': drivers/pinctrl/pinctrl-amd.c:210:3: warning: 'pin_num' may be used uninitialized in this function [-Wmaybe-uninitialized] for (; i < pin_num; i++) { ^ drivers/pinctrl/pinctrl-amd.c:172:21: warning: 'i' may be used uninitialized in this function [-Wmaybe-uninitialized] unsigned int bank, i, pin_num; ^ Fix this by adding a guarding default case for illegal bank numbers. Cc: S-k Shyam-sundar <Shyam-sundar.S-k@amd.com> Cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-29pinctrl/amd: Set the level based on ACPI tablesShyam Sundar S K
In the function amd_gpio_irq_set_type, read the values from the ACPI table to set the level and drop the settings passed by the client. Cc: <stable@vger.kernel.org> # 4.8.x+ Reviewed-by: Pankaj Sen <Pankaj.Sen@amd.com> Reviewed-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com> Reviewed-by: Shah, Nehal-bakulchandra <Nehal-bakulchandra.Shah@amd.com> Signed-off-by: Shyam-sundar S-k <Shyam-sundar.S-k@amd.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-28pinctrl: amd: Add support for additional GPIOShah, Nehal-bakulchandra
This patch adds support for new Bank and adds IRQCHIP_SKIP_SET_WAKE flag. Reviewed-by: S-k, Shyam-sundar <Shyam-sundar.S-k@amd.com> Signed-off-by: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-09-23Merge tag 'v4.8-rc6' into develLinus Walleij
Linux 4.8-rc6
2016-09-13pinctrl/amd: switch to using a bool for levelAgrawal, Nitesh-kumar
The earlier patch can be simplified by using a bool to indicate level trigger. Reviewed-by: Pankaj Sen <Pankaj.Sen@amd.com> Signed-off-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com> [Fixup to earlier manually applied patch] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-09-07pinctrl/amd: Configure GPIO register using BIOS settingsAgrawal, Nitesh-kumar
In the function amd_gpio_irq_set_type, use the settings provided by the BIOS,when the LevelTrig is Edge and activeLevel is HIGH, to configure the GPIO registers. Ignore the settings from client. Reviewed-by: Pankaj Sen <Pankaj.Sen@amd.com> Signed-off-by:Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-12 20:10:17 +0000