summaryrefslogtreecommitdiff
path: root/drivers/pinctrl/meson
AgeCommit message (Collapse)Author
2019-07-13Merge tag 'pinctrl-v5.3-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v5.3 kernel cycle: Core changes: - Device links can optionally be added between a pin control producer and its consumers. This will affect how the system power management is handled: a pin controller will not suspend before all of its consumers have been suspended. This was necessary for the ST Microelectronics STMFX expander and need to be tested on other systems as well: it makes sense to make this default in the long run. Right now it is opt-in per driver. - Drive strength can be specified in microamps. With decreases in silicon technology, milliamps isn't granular enough, let's make it possible to select drive strengths in microamps. Right now the Meson (AMlogic) driver needs this. New drivers: - New subdriver for the Tegra 194 SoC. - New subdriver for the Qualcomm SDM845. - New subdriver for the Qualcomm SM8150. - New subdriver for the Freescale i.MX8MN (Freescale is now a product line of NXP). - New subdriver for Marvell MV98DX1135. Driver improvements: - The Bitmain BM1880 driver now supports pin config in addition to muxing. - The Qualcomm drivers can now reserve some GPIOs as taken aside and not usable for users. This is used in ACPI systems to take out some GPIO lines used by the BIOS so that noone else (neither kernel nor userspace) will play with them by mistake and crash the machine. - A slew of refurbishing around the Aspeed drivers (board management controllers for servers) in preparation for the new Aspeed AST2600 SoC. - A slew of improvements over the SH PFC drivers as usual. - Misc cleanups and fixes" * tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits) pinctrl: aspeed: Strip moved macros and structs from private header pinctrl: aspeed: Fix missed include pinctrl: baytrail: Use GENMASK() consistently pinctrl: baytrail: Re-use data structures from pinctrl-intel.h pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux() pinctrl: qcom: Add SM8150 pinctrl driver dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding dt-bindings: pinctrl: qcom: Document missing gpio nodes pinctrl: aspeed: Add implementation-related documentation pinctrl: aspeed: Split out pinmux from general pinctrl pinctrl: aspeed: Clarify comment about strapping W1C pinctrl: aspeed: Correct comment that is no longer true MAINTAINERS: Add entry for ASPEED pinctrl drivers dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema dt-bindings: pinctrl: aspeed: Split bindings document in two pinctrl: qcom: Add irq_enable callback for msm gpio pinctrl: madera: Fixup SPDX headers pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard pinctrl: tegra: Add bitmask support for parked bits ...
2019-06-05treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446Thomas Gleixner
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation you should have received a copy of the gnu general public license along with this program if not see http www gnu org licenses extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 30 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190531190115.962665879@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-01pinctrl: meson: update with SPDX Licence identifierNeil Armstrong
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-24pinctrl: meson: add output support in pinconfJerome Brunet
Add pinconf support for PIN_CONFIG_OUTPUT_ENABLE and PIN_CONFIG_OUTPUT in the meson pinctrl driver. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-23pinctrl: meson: g12a: add DS bank valueGuillaume La Roque
add drive-strength bank regiter and bit value for G12A SoC Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-23pinctrl: meson: add support of drive-strength-microampGuillaume La Roque
drive-strength-microamp is a new feature needed for G12A SoC. the default DS setting after boot is usually 500uA and it is not enough for many functions. We need to be able to set the drive strength to reliably enable things like MMC, I2C, etc ... Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-23pinctrl: meson: Rework enable/disable bias partGuillaume La Roque
rework bias enable/disable part to prepare drive-strength integration no functional changes Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-11Merge tag 'pinctrl-v5.1-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is a calm cycle, not much happened this time around: not even much incremental development. Some three new drivers, that is all. No core changes. New drivers: - NXP (ex Freescale) i.MX 8QM driver. - NXP (ex Freescale) i.MX 8MM driver. - AT91 SAM9X60 subdriver. Improvements: - Support for external interrups (EINT) on Mediatek virtual GPIOs. - Make BCM2835 pin config fully generic. - Lots of Renesas SH-PFC incremental improvements" * tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (70 commits) pinctrl: imx: fix scu link errors dt-bindings: pinctrl: Document the i.MX50 IOMUXC binding pinctrl: qcom: spmi-gpio: Reorder debug print pinctrl: nomadik: fix possible object reference leak pinctrl: stm32: return error upon hwspinlock failure pinctrl: stm32: fix memory leak issue pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions pinctrl: sh-pfc: Validate fixed-size field widths at build time pinctrl: sh-pfc: sh73a0: Fix fsic_spdif pin groups pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group pinctrl: sh-pfc: emev2: Add missing pinmux functions pinctrl: sunxi: Support I/O bias voltage setting on A80 pinctrl: ingenic: Add LCD pins for the JZ4725B SoC pinctrl: samsung: Remove legacy API for handling external wakeup interrupts mask pinctrl: bcm2835: Direct GPIO config changes to generic pinctrl pinctrl: bcm2835: declare pin config as generic pinctrl: qcom: qcs404: Drop unused UFS_RESET macro dt-bindings: add documentation for slew rate ...
2019-02-17pinctrl: meson: meson8b: fix the sdxc_a data 1..3 pinsMartin Blumenstingl
Fix the mismatch between the "sdxc_d13_1_a" pin group definition from meson8b_cbus_groups and the entry in sdxc_a_groups ("sdxc_d0_13_1_a"). This makes it possible to use "sdxc_d13_1_a" in device-tree files to route the MMC data 1..3 pins to GPIOX_1..3. Fixes: 0fefcb6876d0d6 ("pinctrl: Add support for Meson8b") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-01-22Merge branch 'ib-meson-fixes' into develLinus Walleij
2019-01-21pinctrl: meson: add optional region for drive strengthJerome Brunet
On the G12a, there is a new 'region' to handle the drive-strength. This is optional since the older do not have this. Fixes: 29ae0952e85f ("pinctrl: meson-g12a: add pinctrl driver support") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-01-21pinctrl: meson: fix G12A ao pull registers base addressXingyu Chen
Since Meson G12A SoC, Introduce new ao registers AO_RTI_PULL_UP_EN_REG and AO_GPIO_O. These bits of controlling output level are remapped to the new register AO_GPIO_O, and the AO_GPIO_O_EN_N support only controlling output enable. These bits of controlling pull enable are remapped to the new register AO_RTI_PULL_UP_EN_REG, and the AO_RTI_PULL_UP_REG support only controlling pull type(up/down). The new layout of ao gpio/pull registers is as follows: - AO_GPIO_O_EN_N [offset: 0x9 << 2] - AO_GPIO_I [offset: 0xa << 2] - AO_RTI_PULL_UP_REG [offset: 0xb << 2] - AO_RTI_PULL_UP_EN_REG [offset: 0xc << 2] - AO_GPIO_O [offset: 0xd << 2] From above, we can see ao GPIO registers region has been separated by the ao pull registers. In order to ensure the continuity of the region on software, the ao GPIO and ao pull registers use the same base address, but can be identified by the offset. Fixes: 29ae0952e85f ("pinctrl: meson-g12a: add pinctrl driver support") Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-01-14pinctrl: meson: meson8b: add the eth_rxd2 and eth_rxd3 pinsMartin Blumenstingl
Gigabit Ethernet requires the Ethernet TXD0..3 and RXD0..3 data lines. Add the missing eth_rxd2 and eth_rxd3 definitions so we don't have to rely on the bootloader to set them up correctly. The vendor u-boot sources for Odroid-C1 use the following Ethernet pinmux configuration: SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f); SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000); This translates to the following pin groups in the mainline kernel: - register 6 bit 0: eth_rxd1 (DIF_0_P) - register 6 bit 1: eth_rxd0 (DIF_0_N) - register 6 bit 2: eth_rx_dv (DIF_1_P) - register 6 bit 3: eth_rx_clk (DIF_1_N) - register 6 bit 6: eth_tx_en (DIF_3_P) - register 6 bit 8: eth_ref_clk (DIF_3_N) - register 6 bit 9: eth_mdc (DIF_4_P) - register 6 bit 10: eth_mdio_en (DIF_4_N) - register 6 bit 11: eth_tx_clk (GPIOH_9) - register 6 bit 12: eth_txd2 (GPIOH_8) - register 6 bit 13: eth_txd3 (GPIOH_7) - register 7 bit 20: eth_txd0_0 (GPIOH_6) - register 7 bit 21: eth_txd1_0 (GPIOH_5) - register 7 bit 22: eth_rxd3 (DIF_2_P) - register 7 bit 23: eth_rxd2 (DIF_2_N) All functions except eth_rxd2 and eth_rxd3 are already supported by the pinctrl-meson8b driver. Suggested-by: Jianxin Pan <jianxin.pan@amlogic.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com> Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-01-01Merge tag 'pinctrl-v4.21-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "We have no core changes but lots of incremental development in drivers all over the place: Renesas, NXP, Mediatek and Actions Semiconductor keep churning out new SoCs. I have some subtree maintainers for Renesas and Intel helping out to keep down the load, it's been working smoothly (Samsung also have a subtree but it was not used this cycle.) New drivers: - NXP (ex Freescale) i.MX 8 QXP SoC driver. - Mediatek MT6797 SoC driver. - Mediatek MT7629 SoC driver. - Actions Semiconductor S700 SoC driver. - Renesas RZ/A2 SoC driver. - Allwinner sunxi suniv F1C100 SoC driver. - Qualcomm PMS405 PMIC driver. - Microsemi Ocelot Jaguar2 SoC driver. Improvements: - Some RT improvements (using raw spinlocks where appropriate). - A lot of new pin sets on the Renesas PFC pin controllers. - GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO chips, and Xway. - Major modernization of the Intel pin control drivers. - STM32 pin control driver will now synchronize usage of pins with another CPU using a hardware spinlock" * tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (145 commits) dt-bindings: arm: fsl-scu: add imx8qm pinctrl support pinctrl: freescale: Break dependency on SOC_IMX8MQ for i.MX8MQ pinctrl: imx-scu: Depend on IMX_SCU pinctrl: ocelot: Add dependency on HAS_IOMEM pinctrl: ocelot: add MSCC Jaguar2 support pinctrl: bcm: ns: support updated DT binding as syscon subnode dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon MAINTAINERS: merge at91 pinctrl entries pinctrl: imx8qxp: break the dependency on SOC_IMX8QXP pinctrl: uniphier: constify uniphier_pinctrl_socdata pinctrl: mediatek: improve Kconfig dependencies pinctrl: msm: mark PM functions as __maybe_unused dt-bindings: pinctrl: sunxi: Add supply properties pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARD pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARD pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs" pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs" pinctrl: meson: meson8b: fix the GPIO function for the GPIOAO pins pinctrl: meson: meson8: fix the GPIO function for the GPIOAO pins pinctrl: sh-pfc: Make pinmux_cfg_reg.var_field_width[] variable-length ...
2018-12-21pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARDMartin Blumenstingl
Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be configured in devicetree using groups = BOOTx or groups = CARDx. This makes the behavior consistent with other pins inside the same driver as well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers. Fixes: 0fefcb6876d0d6 ("pinctrl: Add support for Meson8b") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-21pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARDMartin Blumenstingl
Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be configured in devicetree using groups = BOOTx or groups = CARDx. This makes the behavior consistent with other pins inside the same driver as well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers. Fixes: 6ac730951104a4 ("pinctrl: add driver for Amlogic Meson SoCs") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-21pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"Martin Blumenstingl
Rename the existing "gpio" function to "gpio_periphs". This makes it consistent with the "gpio_aobus" function. Also GXBB and GXL are also using the "gpio_periphs" naming, so this makes the code here consistent with other Amlogic pinctrl drivers. No functional changes since thee "gpio" function is currently not used. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-21pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"Martin Blumenstingl
Rename the existing "gpio" function to "gpio_periphs". This makes it consistent with the "gpio_aobus" function. Also GXBB and GXL are also using the "gpio_periphs" naming, so this makes the code here consistent with other Amlogic pinctrl drivers. No functional changes since thee "gpio" function is currently not used. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-21pinctrl: meson: meson8b: fix the GPIO function for the GPIOAO pinsMartin Blumenstingl
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N) only belong to the pin controller in the AO domain. With the current definition these pins cannot be referred to in .dts files as group (which is possible on GXBB and GXL for example). Add a separate "gpio_aobus" function to fix the mapping between the pin controller and the GPIO pins in the AO domain. This is similar to how the GXBB and GXL drivers implement this functionality. Fixes: 9dab1868ec0db4 ("pinctrl: amlogic: Make driver independent from two-domain configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-21pinctrl: meson: meson8: fix the GPIO function for the GPIOAO pinsMartin Blumenstingl
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N) only belong to the pin controller in the AO domain. With the current definition these pins cannot be referred to in .dts files as group (which is possible on GXBB and GXL for example). Add a separate "gpio_aobus" function to fix the mapping between the pin controller and the GPIO pins in the AO domain. This is similar to how the GXBB and GXL drivers implement this functionality. Fixes: 9dab1868ec0db4 ("pinctrl: amlogic: Make driver independent from two-domain configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-19pinctrl: meson: fix pull enable register calculationJerome Brunet
We just changed the code so we apply bias disable on the correct register but forgot to align the register calculation. The result is that we apply the change on the correct register, but possibly at the incorrect offset/bit This went undetected because offsets tends to be the same between REG_PULL and REG_PULLEN for a given pin the EE controller. This is not true for the AO controller. Fixes: e39f9dd8206a ("pinctrl: meson: fix pinconf bias disable") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-15pinctrl: meson-gxl: remove invalid GPIOX tsin_a pinsNeil Armstrong
The GPIOX tsin_a pins wrongly uses the SDCard pinctrl bits, this patch completely removes these pins entries until we find out what are the correct bits and registers to be used instead. Fixes: 5a6ae9b80139 ("pinctrl: meson-gxl: add tsin_a pins") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-05pinctrl: meson: fix meson8b ao pull register bitsJerome Brunet
AO pull register definition is inverted between pull (up/down) and pull enable. Fixing this allows to properly apply bias setting through pinconf Fixes: 0fefcb6876d0 ("pinctrl: Add support for Meson8b") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-05pinctrl: meson: fix meson8 ao pull register bitsJerome Brunet
AO pull register definition is inverted between pull (up/down) and pull enable. Fixing this allows to properly apply bias setting through pinconf Fixes: 6ac730951104 ("pinctrl: add driver for Amlogic Meson SoCs") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-05pinctrl: meson: fix gxl ao pull register bitsJerome Brunet
AO pull register definition is inverted between pull (up/down) and pull enable. Fixing this allows to properly apply bias setting through pinconf Fixes: 0f15f500ff2c ("pinctrl: meson: Add GXL pinctrl definitions") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-05pinctrl: meson: fix gxbb ao pull register bitsJerome Brunet
AO pull register definition is inverted between pull (up/down) and pull enable. Fixing this allows to properly apply bias setting through pinconf Fixes: 468c234f9ed7 ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-05pinctrl: meson: fix pinconf bias disableJerome Brunet
If a bias is enabled on a pin of an Amlogic SoC, calling .pin_config_set() with PIN_CONFIG_BIAS_DISABLE will not disable the bias. Instead it will force a pull-down bias on the pin. Instead of the pull type register bank, the driver should access the pull enable register bank. Fixes: 6ac730951104 ("pinctrl: add driver for Amlogic Meson SoCs") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-14pinctrl: Include <linux/gpio/driver.h> nothing elseLinus Walleij
These drivers are GPIO drivers, and the do not need to use the legacy header in <linux/gpio.h>, go directly for <linux/gpio/driver.h> instead. Replace any use of GPIOF_* with 0/1, these flags are for consumers, not drivers. Get rid of a few gpio_to_irq() users that was littering around the place, use local callbacks or avoid using it at all. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-08-29pinctrl: Convert to using %pOFn instead of device_node.nameRob Herring
In preparation to remove the node name pointer from struct device_node, convert printf users to use the %pOFn format specifier. Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Dong Aisheng <aisheng.dong@nxp.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Stefan Agner <stefan@agner.ch> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Sean Wang <sean.wang@mediatek.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@bootlin.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Tony Lindgren <tony@atomide.com> Cc: Haojian Zhuang <haojian.zhuang@linaro.org> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Barry Song <baohua@kernel.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: linux-gpio@vger.kernel.org Cc: linux-mediatek@lists.infradead.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-amlogic@lists.infradead.org Cc: linux-rockchip@lists.infradead.org Cc: linux-omap@vger.kernel.org Acked-by: Dong Aisheng <aisheng.dong@nxp.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Sean Wang <sean.wang@mediatek.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-08-29pinctrl: meson-g12a: add pinctrl driver supportYixun Lan
Add the pinctrl driver for Meson-G12A SoC which share the similar IP as the previous Meson-AXG SoC, both use same pinmux ops (register layout). A new driver is needed here due to the differences in the pins. Starting from Meson-AXG SoC, the pinctrl controller block use 4 continues register bits to specific the pin mux function, while comparing to old generation SoC which using variable length register bits for the pin mux definition. The new design greatly simplify the software model. For the detail example, one 32bit register can be divided into 8 parts, each has 4 bits whose value start from 0 - 7, each can describe one pin, the value 0 is always devoted to GPIO function, while 1 - 7 devoted to the mux pin function. Please note, the GPIOE is actually located at AO (always on) bank. Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-07-16pinctrl: meson: add gen_clk pinsJerome Brunet
Add the pinctrl configuration for gen_clk on gxbb and axg. gen_clk allows to output and devide several internal clocks of SoC, including most of the plls. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-06-07Merge tag 'pinctrl-v4.18-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for v4.18. No core changes this time! Just a calm all-over-the-place drivers, updates and fixes cycle as it seems. New drivers/subdrivers: - Actions Semiconductor S900 driver with more Actions variants for S700, S500 in the pipe. Also generic GPIO support on top of the same driver and IRQ support is in the pipe. - Renesas r8a77470 PFC support. - Renesas r8a77990 PFC support. - Allwinner Sunxi H6 R_PIO support. - Rockchip PX30 support. - Meson Meson8m2 support. - Remove support for the ill-fated Samsung Exynos 5440 SoC. Improvements: - Context save/restore support in pinctrl-single. - External interrupt support for the Mediatek MT7622. - Qualcomm ACPI HID QCOM8002 supported. Fixes: - Fix up suspend/resume support for Exynos 5433. - Fix Strago DMI fixes on the Intel Cherryview" * tag 'pinctrl-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits) pinctrl: cherryview: limit Strago DMI workarounds to version 1.0 pinctrl: at91-pio4: add missing of_node_put pinctrl: armada-37xx: Fix spurious irq management gpiolib: discourage gpiochip_add_pin[group]_range for DT pinctrls pinctrl: msm: fix gpio-hog related boot issues MAINTAINERS: update entry for Mediatek pin controller pinctrl: mediatek: remove unused fields in struct mtk_eint_hw pinctrl: mediatek: use generic EINT register maps for each SoC pinctrl: mediatek: add EINT support to MT7622 SoC pinctrl: mediatek: refactor EINT related code for all MediaTek pinctrl can fit dt-bindings: pinctrl: add external interrupt support to MT7622 pinctrl pinctrl: freescale: Switch to SPDX identifier pinctrl: samsung: Fix suspend/resume for Exynos5433 GPF1..5 banks pinctrl: sh-pfc: rcar-gen3: Fix grammar in static pin comments pinctrl: sh-pfc: r8a77965: Add I2C pin support pinctrl: sh-pfc: r8a77990: Add EthernetAVB pins, groups and functions pinctrl: sh-pfc: r8a77990: Add I2C{1,2,4,5,6,7} pins, groups and functions pinctrl: sh-pfc: r8a77990: Add SCIF pins, groups and functions pinctrl: sh-pfc: r8a77990: Add bias pinconf support pinctrl: sh-pfc: Initial R8A77990 PFC support ...
2018-05-16pinctrl: nand: meson-gxl: fix missing data pinsYixun Lan
The data pin 0-7 of the NAND controller are actually missing from the nand pinctrl group, so we fix it here. Fixes: 0f15f500ff2c ("pinctrl: meson: Add GXL pinctrl definitions") Reported-by: Liang Yang <liang.yang@amlogic.com> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-16pinctrl: nand: meson-gxbb: fix missing data pinsYixun Lan
The data pin 0-7 of the NAND controller are actually missing from the nand pinctrl group, so we fix it here. Fixes: cd1e3b01c7d3 ("pinctrl: amlogic: gxbb: add nand pins") Reported-by: Liang Yang <liang.yang@amlogic.com> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-02pinctrl: meson: axg: add tdm pinsJerome Brunet
Add the information related to the tdm pins of the A113D SoC Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-02pinctrl: meson: meson8: add the RGMII RXD2/RXD3 and TXD2/TXD3 signalsMartin Blumenstingl
These are only available on the Meson8m2 SoC (which uses the same DesignWare Ethernet MAC as Meson8b). The "eth_tx_clk_50m" signal either provides a 50MHz clock for the RMII PHYs or the RGMII TX clock (as far as we know the frequency is controlled by the PRG_ETHERNET registers in the Ethernet MAC "glue" IP block). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-02pinctrl: meson: meson8: add support for the Meson8m2 SoCMartin Blumenstingl
Add Meson8m2 support to the existing Meson8 pinctrl driver. Since there are only very few changes (Meson8m2 has an extra signal on 10 CBUS pins, no other differences were found so far). Add the new compatible strings for Meson8m2 to the existing Meson8 driver so we don't have to duplicate the whole driver. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-02pinctrl: meson-axg: fix the range of aobus bankYixun Lan
The GPIOAO bank is range from GPIOAO_0 to GPIOAO_13. Fixes: 83c566806a68 ("pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC") Reported-by: Xingyu Chen <xingyu.chen@amlogic.com> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Acked-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-04-03Merge tag 'pinctrl-v4.17-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control bulk updates from Linus Walleij: "New drivers: - Qualcomm SDM845: this is their new flagship SoC platform which seems to be targeted at premium mobile handsets. - Renesas R-Car M3-N SoC. - Renesas R8A77980 SoC. - NXP (ex Freescale) i.MX 6SLL SoC. - Mediatek MT2712 SoC. - Allwinner H6 SoC. Improvements: - Uniphier adds a few new functions and pins. - Renesas refactorings and additional pin definitions. - Improved pin groups for Axis Artpec6. Cleanup: - Drop the TZ1090 drivers. This platform is no longer maintained and is being deleted. - Drop ST-Ericsson U8540/U9540 support as this was never productified. - Overall minor fixes and janitorial" * tag 'pinctrl-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits) pinctrl: uniphier: add UART hardware flow control pin-mux settings pinctrl: sunxi: add support for the Allwinner H6 main pin controller pinctrl: sunxi: change irq_bank_base to irq_bank_map pinctrl: sunxi: introduce IRQ bank conversion function pinctrl: sunxi: refactor irq related register function to have desc pinctrl: msm8998: Remove owner assignment from platform_driver pinctrl: uniphier: divide I2S and S/PDIF audio out pin-mux group pinctrl: uniphier: add PXs2 Audio in/out pin-mux settings pinctrl/amd: poll InterruptEnable bits in enable_irq pinctrl: ocelot: fix gpio direction pinctrl: mtk: fix check warnings. pintcrl: mtk: support bias-disable of generic and special pins simultaneously pinctrl: add mt2712 pinctrl driver pinctrl: pinctrl-single: Fix pcs_request_gpio() when bits_per_mux != 0 pinctrl: imx: Add pinctrl driver support for imx6sll dt-bindings: imx: update pinctrl doc for imx6sll pinctrl: intel: Implement intel_gpio_get_direction callback pinctrl: stm32: add 'depends on HAS_IOMEM' to fix unmet dependency pinctrl: mediatek: mtk-common: use true and false for boolean values pinctrl: sunxi: always look for apb block ...
2018-03-02pinctrl: meson: meson8b: fix requesting GPIOs greater than GPIOZ_3Martin Blumenstingl
Meson8b is a cost reduced variant of the Meson8 SoC. It's package size is smaller than Meson8. Unfortunately there are a few key differences which cannot be seen without close inspection of the code and the public S805 datasheet: - the GPIOX bank is missing the GPIOX_12, GPIOX_13, GPIOX_14 and GPIOX_15 GPIOs - the GPIOY bank is missing the GPIOY_2, GPIOY_4, GPIOY_5, GPIOY_15 and GPIOY_16 GPIOs - the GPIODV bank is missing all GPIOs except GPIODV_9, GPIODV_24, GPIODV_25, GPIODV_26, GPIODV_27, GPIODV_28 and GPIODV_29 - the GPIOZ bank is missing completely - there is a new GPIO bank called "DIF" This means that Meson8b only has 83 actual GPIO lines. Without any holes there would be 130 GPIO lines in total (120 are inherited from Meson8 plus 10 new from the DIF bank). GPIOs greater GPIOZ_3 (whose ID is 83 - as a reminder: this is exactly the number of actual GPIO lines on Meson8b and also the value of meson8b_cbus_pinctrl_data.num_pins) cannot berequested. Using CARD_6 (which used ID 100 prior to this patch, "base of the GPIO controller was 382) as an example: $ echo 482 > /sys/class/gpio/export export_store: invalid GPIO 482 This removes all non-existing pins from to dt-bindings header file (include/dt-bindings/gpio/meson8b-gpio.h). This allows us to have a consecutive numbering for the GPIO #defines (GPIOY_2 doesn't exist for example, so previously the GPIOY_3 ID was "GPIOY_1 + 2", after this patch it is "GPIOY_1 + 1"). As a nice side-effect this means that we get compile-time (instead of runtime) errors if Meson8b .dts uses a pin that only exists on Meson8. Additionally the pinctrl-meson8b driver has to be updated to handle this new GPIO numbering. By default a struct meson_bank only handles GPIO banks where the pins are numbered consecutively because it calculates the bit offsets based on the GPIO IDs. This is solved by taking the original BANK() definition and splitting it into consecutive subsets (X0..11 and X16..21). The bit offsets for each new bank includes the skipped GPIOs (the definition of the "X0..11" bank is identical to the old "X" bank apart from the "last IRQ" field, the definition of the new, split "X16..21" bank takes the original "X" bank and adds 16 - the start of the new split bank - to the "first IRQ", pullen bit, pull bit, dir bit, out bit and in bit). Commit 984cffdeaeb7ea ("pinctrl: Fix gpio/pin mapping for Meson8b") fixed the same issue by setting "ngpio" (of the gpio_chip) to 130. Unfortunately this broke in db80f0e158e621 ("pinctrl: meson: get rid of unneeded domain structures"). The solution from this patch was considered to be better than the previous attempt at fixing this because it provides compile-time error checking for the GPIOs that exist on Meson8 but don't exist on Meson8b. The following pins were tested on an Odroid-C1 using the sysfs GPIO interface checking that their value (high or low) could be read: - GPIOX_0, GPIOX_1, GPIOX_2, GPIOX_3, GPIOX_4, GPIOX_5, GPIOX_6, GPIOX_7, GPIOX_8, GPIOX_9, GPIOX_10, GPIOX_11, GPIOX_18, GPIOX_19, GPIOX_20, GPIOX_21 - GPIOY_3, GPIOY_7, GPIOY_8 (some of these had to be pulled up because they were low by default, others were high by default so these had to be pulled down) Reported-by: Linus Lüssing <linus.luessing@c0d3.blue> Suggested-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-12pinctrl: meson-axg: adjust uart_ao_b pin group namingYixun Lan
Simply adjust the pin group to _x _y _z style, as to keep the consistency in DT with previous naming scheme. Fixes: 83c566806a68 ("pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC") Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-13pinctrl: meson-axg: adjust spicc pin namingYixun Lan
According to datasheet, we should use numbers for the pin naming instead of letters. The patch here try to fix this to keep the consistency. This patch should not bring any functional change. Fixes: 83c566806a68 ("pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC") Suggested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Acked-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-30pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoCXingyu Chen
Add new pinctrl driver for Amlogic's Meson-AXG SoC. Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-30pinctrl: meson-axg: Introduce a pinctrl pinmux ops for Meson-AXG SoCXingyu Chen
The pin controller has been updated in the Amlogic Meson AXG series, which use continuous 4-bit register to select function for each pin. In order to support this, a new pinmux operations "meson_axg_pmx_ops" has been added. Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-10-16pinctrl: meson: rework pinmux opsJerome Brunet
This change prepare the introduction of new meson SoC. This new SoC will share the same gpio/pinconf registers but the pinmux part will be different. While the format of the data associated with each pinmux group will change, the way to handle pinmuxing will be similar. To deal with this new situation, the meson_pmx_struture is kept but the data associated to it is now generic. This allows to reuse the basic functions which would otherwise be copy/pasted in each pinmux driver (such as getting the name a count of groups and functions) Only the functions actually using this specific data is taken out of the common code and is handling the SoC pinmuxing Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-10-16pinctrl: meson: separate soc driversJerome Brunet
When meson pinctrl is enabled, all meson platforms pinctrl drivers are built in the kernel, with a significant amount of data. This leads to situation where pinctrl drivers targeting an architecture are also compiled and shipped on another one (ex: meson8 - ARM - compiled and shipped on ARM64 builds). This is a waste of memory we can easily avoid. This change makes 4 pinctrl drivers (1 per SoC) out the original single driver, allowing to compile and ship only the ones required. Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-10-11pinctrl: meson: remove unused pin_baseJerome Brunet
While removing the need to have pin_base defined in meson pinctrl drivers, I forgot to remove the corresponding field from the pinctrl_data structure. Fixing this now. Fixes: 70e5ecb1b994 ("pinctrl: meson: get rid of pin_base") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-10-11pinctrl: meson-gx: add TEST_N i2s pinmuxJerome Brunet
Add TEST_N pinmux for channel 6 and 7 of the i2s output Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-10-05pinctrl: meson-gxbb: add missing GPIOX_22 pinJerome Brunet
GPIOX_22 is declared as a gpio but the id is no present in the pin table. This hole trigger an error while reading the pingroup debugfs entry GPIOX_22 is no routed externally. For all we know, it could an internal pin of SoC Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>