summaryrefslogtreecommitdiff
path: root/drivers/pinctrl/meson
AgeCommit message (Collapse)Author
2020-07-16pinctrl: meson: pinctrl-meson-a1: Remove unused const variable ↵Lee Jones
'i2c_slave_groups' It has never been used. Fixes the following W=1 kernel build warning(s): drivers/pinctrl/meson/pinctrl-meson-a1.c:749:27: warning: ‘i2c_slave_groups’ defined but not used [-Wunused-const-variable=] 749 | static const char const i2c_slave_groups[] = { | ^~~~~~~~~~~~~~~~ Signed-off-by: Lee Jones <lee.jones@linaro.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Qianggui Song <qianggui.song@amlogic.com> Cc: linux-amlogic@lists.infradead.org Link: https://lore.kernel.org/r/20200713144930.1034632-24-lee.jones@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-07-07pinctrl: meson: fix drive strength register and bit calculationHyeonki Hong
If a GPIO bank has greater than 16 pins, PAD_DS_REG is split into two or more registers. However, when register and bit were calculated, the first register defined in the bank was used, and the bit was calculated based on the first pin. This causes problems in setting the driving strength. The following method was used to solve this problem: A bit is calculated first using predefined strides. Then, If the bit is 32 or more, the register is changed by the quotient of the bit divided by 32. And the bit is set to the remainder. Signed-off-by: Hyeonki Hong <hhk7734@gmail.com> Link: https://lore.kernel.org/r/20200618025916.GA19368@home-desktop Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-04-28pinctrl: meson: wire up the gpio_chip's set_config callbackMartin Blumenstingl
Use gpiochip_generic_config for the gpio_chip's set_config callback so GPIO flags like GPIO_PULL_UP or GPIO_PULL_DOWN can be used in the board .dts descriptions. This is required for some Meson8m2 boards where GPIO_BSD_EN provides the "MUTE" signal and requires enabling the internal pull-up resistor. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20200417183349.1283092-3-martin.blumenstingl@googlemail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-04-28pinctrl: meson: implement the gpio_chip get_direction callbackMartin Blumenstingl
Implement the get_direction callback so we read the direction from the actual GPIO controller register. This is recommended by the gpio_chip kernel doc. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20200417183349.1283092-2-martin.blumenstingl@googlemail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-04-02Merge tag 'pinctrl-v5.7-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v5.7 kernel cycle. There are no core changes this time, only driver developments: - New driver for the Dialog Semiconductor DA9062 Power Management Integrated Circuit (PMIC). - Renesas SH-PFC has improved consistency, with group and register checks in the configuration checker. - New subdriver for the Qualcomm IPQ6018. - Add the RGMII pin control functionality to Qualcomm IPQ8064. - Performance and code quality cleanups in the Mediatek driver. - Improve the Broadcom BCM2835 support to cover all the GPIOs that exist in it. - The Allwinner/Sunxi driver properly masks non-wakeup IRQs on suspend. - Add some missing groups and functions to the Ingenic driver. - Convert some of the Freescale device tree bindings to use the new and all improved JSON YAML markup. - Refactorings and support for the SFIO/GPIO in the Tegra194 SoC driver. - Support high impedance mode in the Spreadtrum/Unisoc driver" * tag 'pinctrl-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (64 commits) pinctrl: qcom: fix compilation error pinctrl: qcom: use scm_call to route GPIO irq to Apps pinctrl: sprd: Add pin high impedance mode support pinctrl: sprd: Use the correct pin output configuration pinctrl: tegra: Add SFIO/GPIO programming on Tegra194 pinctrl: tegra: Renumber the GG.0 and GG.1 pins pinctrl: tegra: Do not add default pin range on Tegra194 pinctrl: tegra: Pass struct tegra_pmx for pin range check pinctrl: tegra: Fix "Scmitt" -> "Schmitt" typo pinctrl: tegra: Fix whitespace issues for improved readability pinctrl: mediatek: Use scnprintf() for avoiding potential buffer overflow pinctrl: freescale: drop the dependency on ARM64 for i.MX8M Revert "pinctrl: mvebu: armada-37xx: use use platform api" dt-bindings: pinctrl: at91: Fix a typo ("descibe") pinctrl: meson: add tsin pinctrl for meson gxbb/gxl/gxm pinctrl: sprd: Fix the kconfig warning pinctrl: ingenic: add hdmi-ddc pin control group pinctrl: sirf/atlas7: Replace zero-length array with flexible-array member pinctrl: sprd: Allow the SPRD pinctrl driver building into a module pinctrl: Export some needed symbols at module load time ...
2020-03-12pinctrl: meson: add tsin pinctrl for meson gxbb/gxl/gxmIgor Vavro
Add the tsin pinctrl definitions needed for integrated DVB hardware support on Meson GXBB/GXL/GXM boards. changes in v2 - fix ordering and numbering of uart_c ping flagged by Otto in [1] [1] http://lists.infradead.org/pipermail/linux-amlogic/2020-March/015906.html Signed-off-by: Igor Vavro <afl2001@gmail.com> [updated commit message] Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Link: https://lore.kernel.org/r/1583377666-13378-1-git-send-email-christianshewitt@gmail.com Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-02-21pinctrl: meson-gxl: fix GPIOX sdio pinsNicolas Belin
In the gxl driver, the sdio cmd and clk pins are inverted. It has not caused any issue so far because devices using these pins always take both pins so the resulting configuration is OK. Fixes: 0f15f500ff2c ("pinctrl: meson: Add GXL pinctrl definitions") Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Nicolas Belin <nbelin@baylibre.com> Link: https://lore.kernel.org/r/1582204512-7582-1-git-send-email-nbelin@baylibre.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-01-29Merge tag 'pinctrl-v5.6-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes, nothing too exciting about this. Some changes hit arch/sh and arch/arm but are well isolated and acknowledged by the respective arch maintainers. Core changes: - Dropped the chained IRQ setup callback into GPIOLIB as we got rid of the last users of that in this changeset. New drivers: - New driver for Ingenic X1830. - New driver for Freescale i.MX8MP. Driver enhancements: - Fix all remaining Intel drivers to pass their IRQ chips along with the GPIO chips. - Intel Baytrail allocates its irqchip dynamically. - Intel Lynxpoint is thoroughly rewritten and modernized. - Aspeed AST2600 pin muxing and configuration is much improved. - Qualcomm SC7180 functions are updated and wakeup interrupt map is provided. - A whole slew of Renesas SH-PFC cleanups and improvements. - Fix up the Intel DT bindings to use the generic YAML DT bindings schema (a first user of this)" * tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits) pinctrl: madera: Remove extra blank line pinctrl: qcom: Don't lock around irq_set_irq_wake() pinctrl: mvebu: armada-37xx: use use platform api gpio: Drop the chained IRQ handler assign function pinctrl: freescale: Add i.MX8MP pinctrl driver support dt-bindings: imx: Add pinctrl binding doc for i.MX8MP pinctrl: tigerlake: Tiger Lake uses _HID enumeration pinctrl: sunrisepoint: Add Coffee Lake-S ACPI ID pinctrl: iproc: Use platform_get_irq_optional() to avoid error message pinctrl: dt-bindings: Fix some errors in the lgm and pinmux schema pinctrl: intel: Pass irqchip when adding gpiochip pinctrl: intel: Add GPIO <-> pin mapping ranges via callback pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins pinctrl: sunrisepoint: Add missing Interrupt Status register offset pinctrl: sh-pfc: Split R-Car H3 support in two independent drivers pinctrl: artpec6: fix __iomem on reg in set pinctrl: ingenic: Use devm_platform_ioremap_resource() pinctrl: ingenic: Factorize irq_set_type function pinctrl: ingenic: Remove duplicated ingenic_chip_info structures ...
2020-01-07pinctrl: meson: meson8b: add the GPIOH pinmux settings for ETH_RXD{2,3}Martin Blumenstingl
GPIOH_5 and GPIOH_6 can have two Ethernet related functions: - GPIOH_5 can be ETH_TXD1 or ETH_RXD3 - GPIOH_6 can be ETH_TXD0 or ETH_RXD2 Add the bits for eth_rxd3_h and eth_rxd2_h so the ETH_RXD function can be disabled when using the ETH_TXD function of GPIOH_{5,6}. No problem was observed so far, but in theory this could lead to two different signals being routed to the same pad (which could break Ethernet). These settings were found in the public "Amlogic Ethernet controller user guide": http://openlinux.amlogic.com/@api/deki/files/75/=Amlogic_Ethenet_controller_user_Guide.pdf Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20191226191425.3797490-1-martin.blumenstingl@googlemail.com Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-01-07pinctrl: meson: Fix wrong shift value when get drive-strengthQianggui Song
In meson_pinconf_get_drive_strength, variable bit is calculated by meson_calc_reg_and_bit, this value is the offset from the first pin of a certain bank to current pin, while Meson SoCs use two bits for each pin to depict drive-strength. So a left shift by 1 should be done or node pinconf-pins shows wrong message. Fixes: 6ea3e3bbef37 ("pinctrl: meson: add support of drive-strength-microamp") Signed-off-by: Qianggui Song <qianggui.song@amlogic.com> Link: https://lore.kernel.org/r/20191226023734.9631-1-qianggui.song@amlogic.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-12-12pinctrl: meson-axg: Use the correct style for SPDX License IdentifierNishad Kamdar
This patch corrects the SPDX License Identifier style in header file related Meson axg SoC pinctrl driver. It assigns explicit block comment for the SPDX License Identifier. Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Link: https://lore.kernel.org/r/bcb86aa22d8d8499502bbd8c54a364be24886a86.1574871463.git.nishadkamdar@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-11-19pinctrl: meson: add pinctrl driver support for Meson-A1 SoCQianggui Song
Meson A1 SoC share the same register layout of pinmux with previous Meson-G12A, however there is difference for gpio and pin config register in A1. The main difference is that registers before A1 are grouped by function while those of A1 are by bank. The new register layout is as below: /* first bank */ /* addr */ - P_PADCTRL_GPIOP_I base + 0x00 << 2 - P_PADCTRL_GPIOP_O base + 0x01 << 2 - P_PADCTRL_GPIOP_OEN base + 0x02 << 2 - P_PADCTRL_GPIOP_PULL_EN base + 0x03 << 2 - P_PADCTRL_GPIOP_PULL_UP base + 0x04 << 2 - P_PADCTRL_GPIOP_DS base + 0x05 << 2 /* second bank */ - P_PADCTRL_GPIOB_I base + 0x10 << 2 - P_PADCTRL_GPIOB_O base + 0x11 << 2 - P_PADCTRL_GPIOB_OEN base + 0x12 << 2 - P_PADCTRL_GPIOB_PULL_EN base + 0x13 << 2 - P_PADCTRL_GPIOB_PULL_UP base + 0x14 << 2 - P_PADCTRL_GPIOB_DS base + 0x15 << 2 Each bank contains at least 6 registers to be configured, if one bank has more than 16 gpios, an extra P_PADCTRL_GPIO[X]_DS_EXT is included. Between two adjacent P_PADCTRL_GPIO[X]_I, there is an offset 0x10, that is to say, for third bank, the offsets will be 0x20,0x21,0x22,0x23,0x24 ,0x25 according to above register layout. For previous chips, registers are grouped according to their functions while registers of A1 are according to bank.Also note that there is no AO bank any more in A1. Current Meson pinctrl driver can cover such change by using base address of GPIO as that of drive-strength. While simply giving reg_ds = reg_pullen make wrong value to reg_ds for Socs that do not support drive-strength like AXG.To make things simple, add an extra dt parser function for a1 and remain the old dt parser function for only reg parsing. Signed-off-by: Qianggui Song <qianggui.song@amlogic.com> Link: https://lore.kernel.org/r/1573819429-6937-3-git-send-email-qianggui.song@amlogic.com Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-11-19pinctrl: meson: add a new callback for SoCs fixupQianggui Song
In meson_pinctrl_parse_dt, it contains two parts: reg parsing and SoC relative fixup for AO. Several fixups in the same code make it hard to maintain, so move all fixups to each SoC's callback and make meson_pinctrl_parse_dt just do the reg parsing, separate these two parts.Overview of all current Meson SoCs fixup is as below: +------+--------------------------------------+--------------------------+ | | | | | SoC | EE domain | AO domain | +------+--------------------------------------+--------------------------+ |m8 | parse regs: | parse regs: | |m8b | gpio,mux,pull,pull-enable(skip ds) | gpio,mux,pull(skip ds)| |gxl | fixup: | fixup: | |gxbb | no | pull-enable = pull; | |axg | | | +------+--------------------------------------+--------------------------+ |g12a | parse regs: | parse regs: | |sm1 | gpio,mux,pull,pull-enable,ds | gpio,mux,ds | | | fixup: | fixup: | | | no | pull = gpio; | | | | pull-enable = gpio; | +------+--------------------------------------+--------------------------+ |a1 or | parse regs: | |later | gpio/mux (without ao domain) | |SoCs | fixup: | | | pull = gpio; pull-enable = gpio; ds = gpio; | +------+-----------------------------------------------------------------+ Since m8-axg share the same ao fixup, make a common function meson8_aobus_parse_dt_extra to do the job. Signed-off-by: Qianggui Song <qianggui.song@amlogic.com> Link: https://lore.kernel.org/r/1573819429-6937-2-git-send-email-qianggui.song@amlogic.com Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-09-13pinctrl: meson-gxbb: Fix wrong pinning definition for uart_cOtto Meier
Hi i tried to use the uart_C of the the odroid-c2. I enabled it in the dts file. During boot it crashed when the the sdcard slot is addressed. After long search in the net i found this: https://forum.odroid.com/viewtopic.php?f=139&t=25371&p=194370&hilit=uart_C#p177856 After changing the pin definitions accordingly erverything works. Uart_c is functioning and sdcard ist working. Fixes: 6db0f3a8a04e46 ("pinctrl: amlogic: gxbb: add more UART pins") Signed-off-by: Otto Meier <gf435@gmx.net> Link: https://lore.kernel.org/r/1cc32a18-464d-5531-7a1c-084390e2ecb1@gmx.net Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-08-23pinctrl: meson: meson: Add of_node_put() before returnNishka Dasgupta
Each iteration of for_each_child_of_node puts the previous node, but in the case of a return from the middle of the loop, there is no put, thus causing a memory leak. Hence add an of_node_put before the return. Issue found with Coccinelle. Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com> Link: https://lore.kernel.org/r/20190815060718.3286-1-nishkadg.linux@gmail.com Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-08-05pinctrl: meson-g12a: add pwm_a on GPIOE_2 pinmuxNeil Armstrong
Add the missing pinmux for the pwm_a function on the GPIOE_2 pin. Reviewed-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20190729125838.6498-1-narmstrong@baylibre.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-07-13Merge tag 'pinctrl-v5.3-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v5.3 kernel cycle: Core changes: - Device links can optionally be added between a pin control producer and its consumers. This will affect how the system power management is handled: a pin controller will not suspend before all of its consumers have been suspended. This was necessary for the ST Microelectronics STMFX expander and need to be tested on other systems as well: it makes sense to make this default in the long run. Right now it is opt-in per driver. - Drive strength can be specified in microamps. With decreases in silicon technology, milliamps isn't granular enough, let's make it possible to select drive strengths in microamps. Right now the Meson (AMlogic) driver needs this. New drivers: - New subdriver for the Tegra 194 SoC. - New subdriver for the Qualcomm SDM845. - New subdriver for the Qualcomm SM8150. - New subdriver for the Freescale i.MX8MN (Freescale is now a product line of NXP). - New subdriver for Marvell MV98DX1135. Driver improvements: - The Bitmain BM1880 driver now supports pin config in addition to muxing. - The Qualcomm drivers can now reserve some GPIOs as taken aside and not usable for users. This is used in ACPI systems to take out some GPIO lines used by the BIOS so that noone else (neither kernel nor userspace) will play with them by mistake and crash the machine. - A slew of refurbishing around the Aspeed drivers (board management controllers for servers) in preparation for the new Aspeed AST2600 SoC. - A slew of improvements over the SH PFC drivers as usual. - Misc cleanups and fixes" * tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits) pinctrl: aspeed: Strip moved macros and structs from private header pinctrl: aspeed: Fix missed include pinctrl: baytrail: Use GENMASK() consistently pinctrl: baytrail: Re-use data structures from pinctrl-intel.h pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux() pinctrl: qcom: Add SM8150 pinctrl driver dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding dt-bindings: pinctrl: qcom: Document missing gpio nodes pinctrl: aspeed: Add implementation-related documentation pinctrl: aspeed: Split out pinmux from general pinctrl pinctrl: aspeed: Clarify comment about strapping W1C pinctrl: aspeed: Correct comment that is no longer true MAINTAINERS: Add entry for ASPEED pinctrl drivers dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema dt-bindings: pinctrl: aspeed: Split bindings document in two pinctrl: qcom: Add irq_enable callback for msm gpio pinctrl: madera: Fixup SPDX headers pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard pinctrl: tegra: Add bitmask support for parked bits ...
2019-06-05treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446Thomas Gleixner
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation you should have received a copy of the gnu general public license along with this program if not see http www gnu org licenses extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 30 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190531190115.962665879@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-01pinctrl: meson: update with SPDX Licence identifierNeil Armstrong
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-24pinctrl: meson: add output support in pinconfJerome Brunet
Add pinconf support for PIN_CONFIG_OUTPUT_ENABLE and PIN_CONFIG_OUTPUT in the meson pinctrl driver. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-23pinctrl: meson: g12a: add DS bank valueGuillaume La Roque
add drive-strength bank regiter and bit value for G12A SoC Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-23pinctrl: meson: add support of drive-strength-microampGuillaume La Roque
drive-strength-microamp is a new feature needed for G12A SoC. the default DS setting after boot is usually 500uA and it is not enough for many functions. We need to be able to set the drive strength to reliably enable things like MMC, I2C, etc ... Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-23pinctrl: meson: Rework enable/disable bias partGuillaume La Roque
rework bias enable/disable part to prepare drive-strength integration no functional changes Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-11Merge tag 'pinctrl-v5.1-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is a calm cycle, not much happened this time around: not even much incremental development. Some three new drivers, that is all. No core changes. New drivers: - NXP (ex Freescale) i.MX 8QM driver. - NXP (ex Freescale) i.MX 8MM driver. - AT91 SAM9X60 subdriver. Improvements: - Support for external interrups (EINT) on Mediatek virtual GPIOs. - Make BCM2835 pin config fully generic. - Lots of Renesas SH-PFC incremental improvements" * tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (70 commits) pinctrl: imx: fix scu link errors dt-bindings: pinctrl: Document the i.MX50 IOMUXC binding pinctrl: qcom: spmi-gpio: Reorder debug print pinctrl: nomadik: fix possible object reference leak pinctrl: stm32: return error upon hwspinlock failure pinctrl: stm32: fix memory leak issue pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions pinctrl: sh-pfc: Validate fixed-size field widths at build time pinctrl: sh-pfc: sh73a0: Fix fsic_spdif pin groups pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group pinctrl: sh-pfc: emev2: Add missing pinmux functions pinctrl: sunxi: Support I/O bias voltage setting on A80 pinctrl: ingenic: Add LCD pins for the JZ4725B SoC pinctrl: samsung: Remove legacy API for handling external wakeup interrupts mask pinctrl: bcm2835: Direct GPIO config changes to generic pinctrl pinctrl: bcm2835: declare pin config as generic pinctrl: qcom: qcs404: Drop unused UFS_RESET macro dt-bindings: add documentation for slew rate ...
2019-02-17pinctrl: meson: meson8b: fix the sdxc_a data 1..3 pinsMartin Blumenstingl
Fix the mismatch between the "sdxc_d13_1_a" pin group definition from meson8b_cbus_groups and the entry in sdxc_a_groups ("sdxc_d0_13_1_a"). This makes it possible to use "sdxc_d13_1_a" in device-tree files to route the MMC data 1..3 pins to GPIOX_1..3. Fixes: 0fefcb6876d0d6 ("pinctrl: Add support for Meson8b") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-01-22Merge branch 'ib-meson-fixes' into develLinus Walleij
2019-01-21pinctrl: meson: add optional region for drive strengthJerome Brunet
On the G12a, there is a new 'region' to handle the drive-strength. This is optional since the older do not have this. Fixes: 29ae0952e85f ("pinctrl: meson-g12a: add pinctrl driver support") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-01-21pinctrl: meson: fix G12A ao pull registers base addressXingyu Chen
Since Meson G12A SoC, Introduce new ao registers AO_RTI_PULL_UP_EN_REG and AO_GPIO_O. These bits of controlling output level are remapped to the new register AO_GPIO_O, and the AO_GPIO_O_EN_N support only controlling output enable. These bits of controlling pull enable are remapped to the new register AO_RTI_PULL_UP_EN_REG, and the AO_RTI_PULL_UP_REG support only controlling pull type(up/down). The new layout of ao gpio/pull registers is as follows: - AO_GPIO_O_EN_N [offset: 0x9 << 2] - AO_GPIO_I [offset: 0xa << 2] - AO_RTI_PULL_UP_REG [offset: 0xb << 2] - AO_RTI_PULL_UP_EN_REG [offset: 0xc << 2] - AO_GPIO_O [offset: 0xd << 2] From above, we can see ao GPIO registers region has been separated by the ao pull registers. In order to ensure the continuity of the region on software, the ao GPIO and ao pull registers use the same base address, but can be identified by the offset. Fixes: 29ae0952e85f ("pinctrl: meson-g12a: add pinctrl driver support") Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-01-14pinctrl: meson: meson8b: add the eth_rxd2 and eth_rxd3 pinsMartin Blumenstingl
Gigabit Ethernet requires the Ethernet TXD0..3 and RXD0..3 data lines. Add the missing eth_rxd2 and eth_rxd3 definitions so we don't have to rely on the bootloader to set them up correctly. The vendor u-boot sources for Odroid-C1 use the following Ethernet pinmux configuration: SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f); SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000); This translates to the following pin groups in the mainline kernel: - register 6 bit 0: eth_rxd1 (DIF_0_P) - register 6 bit 1: eth_rxd0 (DIF_0_N) - register 6 bit 2: eth_rx_dv (DIF_1_P) - register 6 bit 3: eth_rx_clk (DIF_1_N) - register 6 bit 6: eth_tx_en (DIF_3_P) - register 6 bit 8: eth_ref_clk (DIF_3_N) - register 6 bit 9: eth_mdc (DIF_4_P) - register 6 bit 10: eth_mdio_en (DIF_4_N) - register 6 bit 11: eth_tx_clk (GPIOH_9) - register 6 bit 12: eth_txd2 (GPIOH_8) - register 6 bit 13: eth_txd3 (GPIOH_7) - register 7 bit 20: eth_txd0_0 (GPIOH_6) - register 7 bit 21: eth_txd1_0 (GPIOH_5) - register 7 bit 22: eth_rxd3 (DIF_2_P) - register 7 bit 23: eth_rxd2 (DIF_2_N) All functions except eth_rxd2 and eth_rxd3 are already supported by the pinctrl-meson8b driver. Suggested-by: Jianxin Pan <jianxin.pan@amlogic.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com> Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-01-01Merge tag 'pinctrl-v4.21-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "We have no core changes but lots of incremental development in drivers all over the place: Renesas, NXP, Mediatek and Actions Semiconductor keep churning out new SoCs. I have some subtree maintainers for Renesas and Intel helping out to keep down the load, it's been working smoothly (Samsung also have a subtree but it was not used this cycle.) New drivers: - NXP (ex Freescale) i.MX 8 QXP SoC driver. - Mediatek MT6797 SoC driver. - Mediatek MT7629 SoC driver. - Actions Semiconductor S700 SoC driver. - Renesas RZ/A2 SoC driver. - Allwinner sunxi suniv F1C100 SoC driver. - Qualcomm PMS405 PMIC driver. - Microsemi Ocelot Jaguar2 SoC driver. Improvements: - Some RT improvements (using raw spinlocks where appropriate). - A lot of new pin sets on the Renesas PFC pin controllers. - GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO chips, and Xway. - Major modernization of the Intel pin control drivers. - STM32 pin control driver will now synchronize usage of pins with another CPU using a hardware spinlock" * tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (145 commits) dt-bindings: arm: fsl-scu: add imx8qm pinctrl support pinctrl: freescale: Break dependency on SOC_IMX8MQ for i.MX8MQ pinctrl: imx-scu: Depend on IMX_SCU pinctrl: ocelot: Add dependency on HAS_IOMEM pinctrl: ocelot: add MSCC Jaguar2 support pinctrl: bcm: ns: support updated DT binding as syscon subnode dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon MAINTAINERS: merge at91 pinctrl entries pinctrl: imx8qxp: break the dependency on SOC_IMX8QXP pinctrl: uniphier: constify uniphier_pinctrl_socdata pinctrl: mediatek: improve Kconfig dependencies pinctrl: msm: mark PM functions as __maybe_unused dt-bindings: pinctrl: sunxi: Add supply properties pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARD pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARD pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs" pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs" pinctrl: meson: meson8b: fix the GPIO function for the GPIOAO pins pinctrl: meson: meson8: fix the GPIO function for the GPIOAO pins pinctrl: sh-pfc: Make pinmux_cfg_reg.var_field_width[] variable-length ...
2018-12-21pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARDMartin Blumenstingl
Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be configured in devicetree using groups = BOOTx or groups = CARDx. This makes the behavior consistent with other pins inside the same driver as well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers. Fixes: 0fefcb6876d0d6 ("pinctrl: Add support for Meson8b") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-21pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARDMartin Blumenstingl
Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be configured in devicetree using groups = BOOTx or groups = CARDx. This makes the behavior consistent with other pins inside the same driver as well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers. Fixes: 6ac730951104a4 ("pinctrl: add driver for Amlogic Meson SoCs") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-21pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"Martin Blumenstingl
Rename the existing "gpio" function to "gpio_periphs". This makes it consistent with the "gpio_aobus" function. Also GXBB and GXL are also using the "gpio_periphs" naming, so this makes the code here consistent with other Amlogic pinctrl drivers. No functional changes since thee "gpio" function is currently not used. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-21pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"Martin Blumenstingl
Rename the existing "gpio" function to "gpio_periphs". This makes it consistent with the "gpio_aobus" function. Also GXBB and GXL are also using the "gpio_periphs" naming, so this makes the code here consistent with other Amlogic pinctrl drivers. No functional changes since thee "gpio" function is currently not used. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-21pinctrl: meson: meson8b: fix the GPIO function for the GPIOAO pinsMartin Blumenstingl
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N) only belong to the pin controller in the AO domain. With the current definition these pins cannot be referred to in .dts files as group (which is possible on GXBB and GXL for example). Add a separate "gpio_aobus" function to fix the mapping between the pin controller and the GPIO pins in the AO domain. This is similar to how the GXBB and GXL drivers implement this functionality. Fixes: 9dab1868ec0db4 ("pinctrl: amlogic: Make driver independent from two-domain configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-21pinctrl: meson: meson8: fix the GPIO function for the GPIOAO pinsMartin Blumenstingl
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N) only belong to the pin controller in the AO domain. With the current definition these pins cannot be referred to in .dts files as group (which is possible on GXBB and GXL for example). Add a separate "gpio_aobus" function to fix the mapping between the pin controller and the GPIO pins in the AO domain. This is similar to how the GXBB and GXL drivers implement this functionality. Fixes: 9dab1868ec0db4 ("pinctrl: amlogic: Make driver independent from two-domain configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-19pinctrl: meson: fix pull enable register calculationJerome Brunet
We just changed the code so we apply bias disable on the correct register but forgot to align the register calculation. The result is that we apply the change on the correct register, but possibly at the incorrect offset/bit This went undetected because offsets tends to be the same between REG_PULL and REG_PULLEN for a given pin the EE controller. This is not true for the AO controller. Fixes: e39f9dd8206a ("pinctrl: meson: fix pinconf bias disable") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-15pinctrl: meson-gxl: remove invalid GPIOX tsin_a pinsNeil Armstrong
The GPIOX tsin_a pins wrongly uses the SDCard pinctrl bits, this patch completely removes these pins entries until we find out what are the correct bits and registers to be used instead. Fixes: 5a6ae9b80139 ("pinctrl: meson-gxl: add tsin_a pins") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-05pinctrl: meson: fix meson8b ao pull register bitsJerome Brunet
AO pull register definition is inverted between pull (up/down) and pull enable. Fixing this allows to properly apply bias setting through pinconf Fixes: 0fefcb6876d0 ("pinctrl: Add support for Meson8b") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-05pinctrl: meson: fix meson8 ao pull register bitsJerome Brunet
AO pull register definition is inverted between pull (up/down) and pull enable. Fixing this allows to properly apply bias setting through pinconf Fixes: 6ac730951104 ("pinctrl: add driver for Amlogic Meson SoCs") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-05pinctrl: meson: fix gxl ao pull register bitsJerome Brunet
AO pull register definition is inverted between pull (up/down) and pull enable. Fixing this allows to properly apply bias setting through pinconf Fixes: 0f15f500ff2c ("pinctrl: meson: Add GXL pinctrl definitions") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-05pinctrl: meson: fix gxbb ao pull register bitsJerome Brunet
AO pull register definition is inverted between pull (up/down) and pull enable. Fixing this allows to properly apply bias setting through pinconf Fixes: 468c234f9ed7 ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-05pinctrl: meson: fix pinconf bias disableJerome Brunet
If a bias is enabled on a pin of an Amlogic SoC, calling .pin_config_set() with PIN_CONFIG_BIAS_DISABLE will not disable the bias. Instead it will force a pull-down bias on the pin. Instead of the pull type register bank, the driver should access the pull enable register bank. Fixes: 6ac730951104 ("pinctrl: add driver for Amlogic Meson SoCs") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-14pinctrl: Include <linux/gpio/driver.h> nothing elseLinus Walleij
These drivers are GPIO drivers, and the do not need to use the legacy header in <linux/gpio.h>, go directly for <linux/gpio/driver.h> instead. Replace any use of GPIOF_* with 0/1, these flags are for consumers, not drivers. Get rid of a few gpio_to_irq() users that was littering around the place, use local callbacks or avoid using it at all. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-08-29pinctrl: Convert to using %pOFn instead of device_node.nameRob Herring
In preparation to remove the node name pointer from struct device_node, convert printf users to use the %pOFn format specifier. Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Dong Aisheng <aisheng.dong@nxp.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Stefan Agner <stefan@agner.ch> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Sean Wang <sean.wang@mediatek.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@bootlin.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Tony Lindgren <tony@atomide.com> Cc: Haojian Zhuang <haojian.zhuang@linaro.org> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Barry Song <baohua@kernel.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: linux-gpio@vger.kernel.org Cc: linux-mediatek@lists.infradead.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-amlogic@lists.infradead.org Cc: linux-rockchip@lists.infradead.org Cc: linux-omap@vger.kernel.org Acked-by: Dong Aisheng <aisheng.dong@nxp.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Sean Wang <sean.wang@mediatek.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-08-29pinctrl: meson-g12a: add pinctrl driver supportYixun Lan
Add the pinctrl driver for Meson-G12A SoC which share the similar IP as the previous Meson-AXG SoC, both use same pinmux ops (register layout). A new driver is needed here due to the differences in the pins. Starting from Meson-AXG SoC, the pinctrl controller block use 4 continues register bits to specific the pin mux function, while comparing to old generation SoC which using variable length register bits for the pin mux definition. The new design greatly simplify the software model. For the detail example, one 32bit register can be divided into 8 parts, each has 4 bits whose value start from 0 - 7, each can describe one pin, the value 0 is always devoted to GPIO function, while 1 - 7 devoted to the mux pin function. Please note, the GPIOE is actually located at AO (always on) bank. Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-07-16pinctrl: meson: add gen_clk pinsJerome Brunet
Add the pinctrl configuration for gen_clk on gxbb and axg. gen_clk allows to output and devide several internal clocks of SoC, including most of the plls. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-06-07Merge tag 'pinctrl-v4.18-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for v4.18. No core changes this time! Just a calm all-over-the-place drivers, updates and fixes cycle as it seems. New drivers/subdrivers: - Actions Semiconductor S900 driver with more Actions variants for S700, S500 in the pipe. Also generic GPIO support on top of the same driver and IRQ support is in the pipe. - Renesas r8a77470 PFC support. - Renesas r8a77990 PFC support. - Allwinner Sunxi H6 R_PIO support. - Rockchip PX30 support. - Meson Meson8m2 support. - Remove support for the ill-fated Samsung Exynos 5440 SoC. Improvements: - Context save/restore support in pinctrl-single. - External interrupt support for the Mediatek MT7622. - Qualcomm ACPI HID QCOM8002 supported. Fixes: - Fix up suspend/resume support for Exynos 5433. - Fix Strago DMI fixes on the Intel Cherryview" * tag 'pinctrl-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits) pinctrl: cherryview: limit Strago DMI workarounds to version 1.0 pinctrl: at91-pio4: add missing of_node_put pinctrl: armada-37xx: Fix spurious irq management gpiolib: discourage gpiochip_add_pin[group]_range for DT pinctrls pinctrl: msm: fix gpio-hog related boot issues MAINTAINERS: update entry for Mediatek pin controller pinctrl: mediatek: remove unused fields in struct mtk_eint_hw pinctrl: mediatek: use generic EINT register maps for each SoC pinctrl: mediatek: add EINT support to MT7622 SoC pinctrl: mediatek: refactor EINT related code for all MediaTek pinctrl can fit dt-bindings: pinctrl: add external interrupt support to MT7622 pinctrl pinctrl: freescale: Switch to SPDX identifier pinctrl: samsung: Fix suspend/resume for Exynos5433 GPF1..5 banks pinctrl: sh-pfc: rcar-gen3: Fix grammar in static pin comments pinctrl: sh-pfc: r8a77965: Add I2C pin support pinctrl: sh-pfc: r8a77990: Add EthernetAVB pins, groups and functions pinctrl: sh-pfc: r8a77990: Add I2C{1,2,4,5,6,7} pins, groups and functions pinctrl: sh-pfc: r8a77990: Add SCIF pins, groups and functions pinctrl: sh-pfc: r8a77990: Add bias pinconf support pinctrl: sh-pfc: Initial R8A77990 PFC support ...
2018-05-16pinctrl: nand: meson-gxl: fix missing data pinsYixun Lan
The data pin 0-7 of the NAND controller are actually missing from the nand pinctrl group, so we fix it here. Fixes: 0f15f500ff2c ("pinctrl: meson: Add GXL pinctrl definitions") Reported-by: Liang Yang <liang.yang@amlogic.com> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-02 13:32:18 +0000