| Age | Commit message (Collapse) | Author |
|---|
|
The Armada 37xx SoC come with 2 pin controllers: one on the south
bridge (managing 28 pins) and one on the north bridge (managing 36 pins).
At the hardware level the controller configure the pins by group and not
pin by pin. This constraint is reflected in the design of the driver:
only the group related functions are implemented.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add pinctrl driver support for the Axis ARTPEC-6 SoC.
There are only some pins that actually have different
functions available, but all can control bias (pull-up/-down)
and drive strength.
Code originally written by Chris Paterson.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
SoC family such as DRA7 family of processors have, in addition
to the regular muxing of pins (as done by pinctrl-single), a separate
hardware module called IODelay which is also expected to be configured.
The "IODelay" module has it's own register space that is independent
of the control module and the padconf register area.
With recent changes to the pinctrl framework, we can now support
this hardware with a reasonably minimal driver by using #pinctrl-cells,
GENERIC_PINCTRL_GROUPS and GENERIC_PINMUX_FUNCTIONS.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay reconfiguration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do as little of muxing as absolutely necessary
without I/O isolation (which can only be done in initial stages of
bootloader).
NOTE: with the system wide I/O isolation scheme present in DRA7 SoC
family, it is not reasonable to do stop all I/O operations for every
such pad configuration scheme. So, we will let it glitch when used in
this mode.
Even with the above limitation, certain functionality such as MMC has
mandatory need for IODelay reconfiguration requirements, depending on
speed of transfer. In these cases, with careful examination of usecase
involved, the expected glitch can be controlled such that it does not
impact functionality.
In short, IODelay module support as a padconf driver being introduced
here is not expected to do SoC wide I/O Isolation and is meant for
a limited subset of IODelay configuration requirements that need to
be dynamic and whose glitchy behavior will not cause functionality
failure for that interface.
IMPORTANT NOTE: we take the approach of keeping LOCK_BITs cleared
to 0x0 at all times, even when configuring Manual IO Timing Modes.
This is done by eliminating the LOCK_BIT=1 setting from Step
of the Manual IO timing Mode configuration procedure. This option
leaves the CFG_* registers unprotected from unintended writes to the
CTRL_CORE_PAD_* registers while Manual IO Timing Modes are configured.
This approach is taken to allow for a generic driver to exist in kernel
world that has to be used carefully in required usecases.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[tony@atomide.com: updated to use generic pinctrl functions, added
binding documentation, updated comments]
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a new driver for pinconf on TI DA850/OMAP-L138/AM18XX. These
SoCs have a separate controller for controlling pullup/pulldown groups.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since the I2C sx150x GPIO expander driver uses platform_data to manage
the pins configurations, rewrite the driver as a pinctrl driver using
pinconf to get/set pin configurations from DT or debugfs.
The pinctrl driver is functionnally equivalent as the gpio-only driver
and can use DT for pinconf. The platform_data confirmation is dropped.
This patchset removed the gpio-only driver and selects the Pinctrl driver
config instead. This patchset also migrates the gpio dt-bindings to pinctrl
and add the pinctrl optional properties.
The driver was tested with a SX1509 device on a BeagleBone black with
interrupt support and on an X86_64 machine over an I2C to USB converter.
This is a fixed version that builds and runs on non-OF platforms and on
arm based OF. The GPIO version is removed and the bindings are also moved
to the pinctrl bindings.
Changes since v2
- rebased on v4.9-rc1
- removed MODULE_DEVICE_TABLE as in upstream bb411e771b0e
("gpio: sx150x: fix implicit assumption module.h is present")
Changes since v1
- Fix Kconfig descriptions on pinctrl and gpio
- Fix Kconfig dependency
- Remove oscio support for non-789 devices
- correct typo in dt bindings
- remove probe reset for non-789 devices
Changes since RFC
- Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms
- No more rely on OF_GPIO config
- Moved and enhanced bindings to pinctrl bindings
- Removed gpio-sx150x.c
- Temporary select PINCTRL_SX150X when GPIO_SX150X
- Temporary mark GPIO_SX150X as deprecated
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
ested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Aspeed SoCs typically provide more than 200 pins for GPIO and other
functions. The signal enabled on a pin is determined on a priority
basis, where a given pin can provide a number of different signal types.
In addition to the priority levels, the Aspeed pin controllers describe
the signal active on a pin by compound logical expressions involving
multiple operators, registers and bits. Some difficulty arises as a
pin's function bit masks for each priority level are frequently not the
same (i.e. we cannot just flip a bit to change from a high to low
priority signal), or even in the same register(s). Some configuration
bits affect multiple pins, while in other cases the signals for a bus
must each be enabled individually.
Together, these features give rise to some complexity in the
implementation. A more complete description of the complexities is
provided in the associated header file.
The patch doesn't implement pinctrl/pinmux/pinconf for any particular
Aspeed SoC, rather it adds the framework for defining pinmux
configurations.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.8 kernel cycle.
Nothing stands out as especially exiting: new drivers, new subdrivers,
lots of cleanups and incremental features.
Business as usual.
New drivers:
- New driver for Oxnas pin control and GPIO. This ARM-based chipset
is used in a few storage (NAS) type devices.
- New driver for the MAX77620/MAX20024 pin controller portions.
- New driver for the Intel Merrifield pin controller.
New subdrivers:
- New subdriver for the Qualcomm MDM9615
- New subdriver for the STM32F746 MCU
- New subdriver for the Broadcom NSP SoC.
Cleanups:
- Demodularization of bool compiled-in drivers.
Apart from this there is just regular incremental improvements to a
lot of drivers, especially Uniphier and PFC"
* tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (131 commits)
pinctrl: fix pincontrol definition for marvell
pinctrl: xway: fix typo
Revert "pinctrl: amd: make it explicitly non-modular"
pinctrl: iproc: Add NSP and Stingray GPIO support
pinctrl: Update iProc GPIO DT bindings
pinctrl: bcm: add OF dependencies
pinctrl: ns2: remove redundant dev_err call in ns2_pinmux_probe()
pinctrl: Add STM32F746 MCU support
pinctrl: intel: Protect set wake flow by spin lock
pinctrl: nsp: remove redundant dev_err call in nsp_pinmux_probe()
pinctrl: uniphier: add Ethernet pin-mux settings
sh-pfc: Use PTR_ERR_OR_ZERO() to simplify the code
pinctrl: ns2: fix return value check in ns2_pinmux_probe()
pinctrl: qcom: update DT bindings with ebi2 groups
pinctrl: qcom: establish proper EBI2 pin groups
pinctrl: imx21: Remove the MODULE_DEVICE_TABLE() macro
Documentation: dt: Add new compatible to STM32 pinctrl driver bindings
includes: dt-bindings: Add STM32F746 pinctrl DT bindings
pinctrl: sunxi: fix nand0 function name for sun8i
pinctrl: uniphier: remove pointless pin-mux settings for PH1-LD11
...
|
|
I got below build error:
ERROR: "tegra_xusb_padctl_legacy_probe"
[drivers/phy/tegra/phy-tegra-xusb.ko] undefined!
with below build configuration:
CONFIG_ARCH_TEGRA=y
CONFIG_PINCTRL_TEGRA_XUSB=y
CONFIG_PHY_TEGRA_XUSB=y
The problem is below line in drivers/pinctrl/Makefile
obj-$(CONFIG_PINCTRL_TEGRA) += tegra/
So even CONFIG_PINCTRL_TEGRA_XUSB=y is set, kbuild still does not compile
the code in drivers/pinctrl/tegra folder if !CONFIG_PINCTRL_TEGRA.
phy-tegra-xusb.c does not use any symbol from pinctrl-tegra.c,
so build pinctrl-tegra.c only when CONFIG_PINCTRL_TEGRA is set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
drivers/pinctrl/bcm/Makefile properly builds individual drivers based on
their respective Kconfig symbols. ARCH_BCM is currently a menuconfig
option from arch/arm/mach-bcm/Kconfig, which is fine, but prevents ARM64
platforms which do not have such menuconfig option from building their
pinctrl drivers, so let's get rid of that dependency.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
MAXIM Semiconductor's PMIC, MAX77620/MAX20024 has 8 GPIO pins
which also act as the special function in alternate mode. Also
there is configuration like push-pull, open drain, FPS timing
etc for these pins.
Add pin control driver to configure these parameters through
pin control APIs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add pinctrl and gpio control support to Oxford Semiconductor OXNAS SoC Family.
This version supports the ARM926EJ-S based OX810SE SoC with 34 IO pins.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
CONFIG_PINCTRL_MTK is more suitable than CONFIG_ARCH_MEDIATEK
to guard the drivers/pinctrl/mediatek/ directory.
(I renamed CONFIG_PINCTRL_MTK_COMMON to CONFIG_PINCTRL_MTK.)
This allows COMPILE_TEST to descend into drivers/pinctrl/mediatek
without CONFIG_ARCH_MEDIATEK define.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
While selecting the driver for compile testing seemed possible,
the driver was not compiled because the driver directory was only
added if ARCH_STM32 was selected.
This patch now makes the pinctrl Makefile to add stm32 directory if
PINCTRL_STM32 is selected.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a driver for the pin controller present on the Microchip PIC32
including the specific variant PIC32MZDA. This driver provides pinmux
and pinconfig operations as well as GPIO and IRQ chips for the GPIO
banks.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Tegra has several pinctrl drivers. Now it is reasonable enough to
move them into drivers/pinctrl/tegra/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
CONFIG_PINCTRL_SUNXI is more suitable than CONFIG_ARCH_SUNXI
to guard the drivers/pinctrl/sunxi/ directory.
(I renamed CONFIG_PINCTRL_SUNXI_COMMON to CONFIG_PINCTRL_SUNXI.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
CONFIG_PINCTRL_PXA is more suitable than CONFIG_ARCH_PXA
to guard the drivers/pinctrl/pxa/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds pinctrl and GPIO support to STMicroelectronic's STM32
family of MCUs.
While it only supports STM32F429 for now, it has been designed to enable
support of other MCUs of the family (e.g. STM32F746).
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As the pxa architecture, at least for pxa27x, supports pin control,
activate it in the pinctrl tree.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
CONFIG_PINCTRL_SPEAR is more suitable than CONFIG_PLAT_SPEAR
to guard the drivers/pinctrl/spear/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
CONFIG_PINCTRL_MVEBU is more suitable than CONFIG_PLAT_ORION
to guard the drivers/pinctrl/mvebu/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
CONFIG_PINCTRL_BERLIN is more suitable than CONFIG_ARCH_BERLIN
to guard the drivers/pinctrl/berlin/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
CONFIG_PINCTRL_UNIPHIER is more suitable than CONFIG_ARCH_UNIPHIER
to guard the drivers/pinctrl/uniphier directory.
The current CONFIG_PINCTRL_UNIPHIER_CORE is a bit long
(it would break the indentation in drivers/pinctrl/Makefile),
so rename it into CONFIG_PINCTRL_UNIPHIER.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a pinctrl/gpio driver for Atmel PIO4 controller available on SAMA5D2
chip family.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds pinctrl and gpio driver to the CX92755 SoC "General
Purpose Pin Mapping" hardware block. The CX92755 is one SoC
from the Conexant Digicolor series. Pin mapping hardware supports
configuring pins as either GPIO, or up to 3 other "client select"
functions. This driver adds support for pin muxing using the
generic device tree binding, and a basic gpiolib driver for
the GPIO functionality.
This driver does not currently support GPIO interrupts, and
pad configuration.
v2:
* Address review comments for Linus Walleij:
- Add a pointer to pinctrl_desc in struct dc_pinmap
- Drop the now redundant pinctrl_pin_desc field
- Adapt dc_get_group_{name,pins} to these changes, and
add a comment explaining the 1-to-1 pin-groups relation
* Staticise dc_pmxops
* Protect the GP_CLIENTSEL clct parameter with parenthesis
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Kbuild should descend into drivers/pinctrl/ only when CONFIG_PINCTRL
is enabled because everything under that directory depends on
CONFIG_PINCTRL.
We can avoid the conditional, ifeq ($(CONFIG_OF),y) ... endif.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The core support for the pinctrl drivers for all the UniPhier SoCs.
Changes in v2:
- drop vogus THIS_MODULE because this file is always built-in
- drop vogus "include <linux/module.h> because this file is
always built-in
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a driver for the pin controller present on the IMG Pistachio SoC.
This driver provides pinmux and pinconfig operations as well as GPIO
and IRQ chips for the GPIO banks.
Changes from v4:
- Switched to using gpiochip_add_pin_range().
- Fixed up Kconfig entry.
Changes from v3:
- Addressed review comments from Ezequiel.
Changes from v2:
- Removed module stuff which would be compiled out.
Changes from v1:
- Addressed review comments from Linus.
- Changed compatible string to "img,pistachio-system-pinctrl".
- Look for GPIO sub-nodes by name.
- A couple of bug fixes.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pinctrl driver for the System Control Unit (SCU) found on NXP
LPC18xx/43xx devices.
Driver uses the generic pinctrl DT bindings for multiplexing
and property settings.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
KERNCZ GPIO is a new IP from AMD. it can be implemented in both x86 and ARM.
Current driver patch only support GPIO in x86.
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
[Moved back to <linux/gpio.h> header]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The mediatek SoCs have GPIO controller that handle both the muxing and GPIOs.
The GPIO controller have pinmux, pull enable, pull select, direction and output high/low control.
This driver include common driver and mt8135 part.
The common driver include the pinctrl driver and GPIO driver.
The mt8135 part contain its special device data.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Consolidate Broadcom pinctrl drivers into drivers/pinctrl/bcm/*
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Tegra210's pinmux supports a different set of pins/options than earlier
SoCs, so requires its own driver (well, table of pin-specific data).
Cc: devicetree@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver for the pinmux and GPIO controller available in
Amlogic Meson SoCs. It currently supports only Meson8, however the
common code should be generic enough to work also for other SoCs after
having defined the proper set of functions and groups.
GPIO interrupts are not supported at the moment due to lack of
documentation.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a pin-control driver for Zynq.
Changes since v2:
- driver-specific DT properties are passed to the core in two arrays,
one for the actual DT parsing one for the debugfs representation.
Issue a compiler warning when the number of entries is not the same
for both arrays.
Changes since v1:
- fix EMIO_SD1_CD pin name
- add USB to pinmux options
changes since RFCv2:
- let Zynq select PINCTRL_ZYNQ. Boot hangs when pinctrl information is
present in DT but no driver available.
- add #defines to get rid of magical constants
- add commas at end of initializers
- separate changes in mach-zynq in separate patch
- add driver specific io-standard DT property
- refactored pinconf set function to not require arguments for
argument-less properties
- squash other patches in
- support for IO-standard property
- support for low-power mode property
- migration to pinconf_generic_dt_node_to_map_all()
- use newly created infrastructure to add pass driver-specific DT
params to pinconf-generic
changes since RFC:
- use syscon/regmap to access registers in SLCR space
- rebase to 3.18: rename enable -> set_mux
- add kernel-doc
- support pinconf
- supported attributes
- pin-bias: pull up, tristate, disable
- slew-rate: 0 == slow, 1 == fast; generic pinconf does not display
argument
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When drivers are compiled in subdirectories the -DDEBUG flag need
to be passed in the individual Makefiles.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Suggested-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We are going to have more pinctrl drivers for Intel hardware so separate
all our pin controller drivers to own directory.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This moves all the Freescale-related drivers (i.MX and MXS) to
its own subdirectory to clear the view.
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Anson Huang <b20788@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Denis Carikli <denis@eukrea.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is currently a kludge to get the Makefile to move down
to sh-pfc:s drivers: the arch definitions are used twice to
get it done. However we can very well use the Kconfig symbol
for the SH PFC pin control feature itself: it doesn't matter
that it comes from a lower leaf in the Kconfig hierarchy which
is completely orthogonal.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Samsung Exynos7 is a ARM64bit processor. Which does not select
the CONFIG_PLAT_SAMSUNG symbol. CONFIG_PINCTRL_SAMSUNG is being
selected for both PLAT_SAMSUNG and ARCH_EXYNOS7 symbols.
This patch modifes the pinctrl/Makefile to use
CONFIG_PINCTRL_SAMSUNG symbol to compile the pinctrl/samsung/*.c
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: linus.walleij@linaro.org
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds pincontrol driver for Freescale i.MX21 SOCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree changes from Olof Johansson:
"Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new
platforms, but there's also a bit of cleanup and code removal for
things that are moved from platform code to DT contents (some OMAP
clock code in particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no
particular order:
- Rockchip RK3288 SoC support, including DTS for a dev board that
they have seeded with some community developers.
- Better support for Hardkernel Exynos4-based ODROID boards.
- CCF conversions (and dtsi contents) for several Renesas platforms.
- Gumstix Pepper (TI AM335x) board support
- TI eval board support for AM437x
- Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an
Ippo tablet with the chipset.
- Allwinner A31 Hummingbird board support, not to be confused with
the SolidRun i.MX-based Hummingboard.
- Tegra30 Apalis board support"
* tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (334 commits)
ARM: dts: Enable USB host0 (EHCI) on rk3288-evb
ARM: dts: add rk3288 ehci usb devices
ARM: dts: Turn on USB host vbus on rk3288-evb
ARM: tegra: apalis t30: fix device tree compatible node
ARM: tegra: paz00: Fix some indentation inconsistencies
ARM: zynq: DT: Clarify Xilinx Zynq platform
ARM: dts: rockchip: add watchdog node
ARM: dts: rockchip: remove pinctrl setting from radxarock uart2
ARM: dts: Add missing pinctrl for uart0/1 for exynos3250
ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250
ARM: dts: Add TMU dt node to monitor the temperature for exynos3250
ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250
ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only
ARM: dts: max77686 is exynos5250-snow only
ARM: zynq: DT: Remove DMA from board DTs
ARM: zynq: DT: Add CAN node
ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table
ARM: dts: Add PMU DT node for exynos5260 SoC
ARM: EXYNOS: Add support for Exynos5410 PMU
ARM: dts: Add PMU to exynos5410
...
|
|
We have a bunch of Nomadik family pin control drivers, so let's
move them into their own subdirectory.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The XUSB pad controller found on NVIDIA Tegra SoCs provides several pads
that lanes can be assigned to in order to support a variety of interface
options: USB 2.0, USB 3.0, PCIe and SATA.
In addition to the pin controller used to assign lanes to pads two PHYs
are exposed to allow the bricks for PCIe and SATA to be powered up and
down by PCIe and SATA drivers.
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Group all pin control drivers of Samsung platform together in
a sub-directory for easy maintenance.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We have four Qualcomm-related pin control drivers, and now there
are drivers coming in for the PMICs on these systems, so let's
create a qcom subdirectory to hold all the Qualcomm stuff.
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds pincontrol driver for Freescale i.MX1 SOCs.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a pinctrl driver for i.MX6 SoloX based on pinctrl-imx core
driver.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Marvell Berlin boards have a group based pinmuxing mechanism. This
adds the core driver support. We actually do not need any information
about the pins here and only have the definition of the groups.
Let's take the example of the uart0 pinmuxing on the BG2Q. Balls BK4 and
BH6 are muxed to respectively UART0 RX and TX if the group GSM12 is set
to mode 0:
Group Modes Offset Base Offset LSB Bit Width
GSM12 3 sm_base 0x40 0x10 0x2
Ball Group Mode 0 Mode 1 Mode 2
BK4 GSM12 UART0_RX IrDA0_RX GPIO9
BH6 GSM12 UART0_TX IrDA0_TX GPIO10
So in order to configure BK4 -> UART0_TX and BH6 -> UART0_RX, we need
to set (sm_base + 0x40 + 0x10) &= ff3fffff.
As pin control registers are part of either chip control or system
control registers, that deal with a bunch of other functions we rely
on a regmap instead of exclusively remapping any resources.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
