| Age | Commit message (Collapse) | Author |
|---|
|
The hardware manual should be revised, but the initial value of
VBCTRL.OCCLREN is set to 1 actually. If the bit is set, the hardware
clears VBCTRL.VBOUT and ADPCTRL.DRVVBUS registers automatically
when the hardware detects over-current signal from a USB power switch.
However, since the hardware doesn't have any registers which
indicates over-current, the driver cannot handle it at all. So, if
"is_otg_channel" hardware detects over-current, since ADPCTRL.DRVVBUS
register is cleared automatically, the channel cannot be used after
that.
To resolve this behavior, this patch sets the VBCTRL.OCCLREN to 0
to keep ADPCTRL.DRVVBUS even if the "is_otg_channel" hardware
detects over-current. (We assume a USB power switch itself protects
over-current and turns the VBUS off.)
This patch is inspired by a BSP patch from Kazuya Mizuguchi.
Fixes: 1114e2d31731 ("phy: rcar-gen3-usb2: change the mode to OTG on the combined channel")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
phy: for 5.3
*) Add a new PHY driver for Qualcomm PCIe2 PHY
*) Add a new PHY driver for Mixel DPHY present in i.MX8
*) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that
PHY enable failed
*) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to
calling a sleeping function from invalid context
*) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to
imbalance powered flag
*) Fix .cocci and sparse warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: qcom-qmp: Raise qcom_qmp_phy_enable() polling delay
phy: meson-g12a-usb3-pcie: disable locking for cr_regmap
phy: Add driver for mixel mipi dphy found on NXP's i.MX8 SoCs
dt-bindings: phy: Add documentation for mixel dphy
dt-bindings: phy-pxa-usb: add bindings
phy: renesas: rcar-gen3-usb2: fix imbalance powered flag
phy: qcom-qmp: Drop useless msm8998_pciephy_cfg setting
phy: qcom-qmp: Correct READY_STATUS poll break condition
phy: ti: am654-serdes: Make serdes_am654_xlate() static
phy: usb: phy-brcm-usb: Fix platform_no_drv_owner.cocci warnings
phy: samsung: Use struct_size() in devm_kzalloc()
phy: qcom: Add Qualcomm PCIe2 PHY driver
dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
|
|
The powered flag should be set for any other phys anyway. Also
the flag should be locked by the channel. Otherwise, after we have
revised the device tree for the usb phy, the following warning
happened during a second system suspend. And if the driver doesn't
lock the flag, an imbalance is possible when enabling the regulator
during system resume. So, this patch fixes the issues.
< The warning >
[ 56.026531] unbalanced disables for USB20_VBUS0
[ 56.031108] WARNING: CPU: 3 PID: 513 at drivers/regulator/core.c:2593 _regula
tor_disable+0xe0/0x1c0
[ 56.040146] Modules linked in: rcar_du_drm rcar_lvds drm_kms_helper drm drm_p
anel_orientation_quirks vsp1 videobuf2_vmalloc videobuf2_dma_contig videobuf2_me
mops videobuf2_v4l2 videobuf2_common videodev snd_soc_rcar renesas_usbhs snd_soc
_audio_graph_card media snd_soc_simple_card_utils crct10dif_ce renesas_usb3 snd_
soc_ak4613 rcar_fcp pwm_rcar usb_dmac phy_rcar_gen3_usb3 pwm_bl ipv6
[ 56.074047] CPU: 3 PID: 513 Comm: kworker/u16:19 Not tainted 5.2.0-rc3-00001-
g5f20a19 #6
[ 56.082129] Hardware name: Renesas Salvator-X board based on r8a7795 ES2.0+ (
DT)
[ 56.089524] Workqueue: events_unbound async_run_entry_fn
[ 56.094832] pstate: 40000005 (nZcv daif -PAN -UAO)
[ 56.099617] pc : _regulator_disable+0xe0/0x1c0
[ 56.104054] lr : _regulator_disable+0xe0/0x1c0
[ 56.108489] sp : ffff0000121c3ae0
[ 56.111796] x29: ffff0000121c3ae0 x28: 0000000000000000
[ 56.117102] x27: 0000000000000000 x26: ffff000010fe0e60
[ 56.122407] x25: 0000000000000002 x24: 0000000000000001
[ 56.127712] x23: 0000000000000002 x22: ffff8006f99d4000
[ 56.133017] x21: ffff8006f99cc000 x20: ffff8006f9846800
[ 56.138322] x19: ffff8006f9846800 x18: ffffffffffffffff
[ 56.143626] x17: 0000000000000000 x16: 0000000000000000
[ 56.148931] x15: ffff0000112f96c8 x14: ffff0000921c37f7
[ 56.154235] x13: ffff0000121c3805 x12: ffff000011312000
[ 56.159540] x11: 0000000005f5e0ff x10: ffff0000112f9f20
[ 56.164844] x9 : ffff0000112d3018 x8 : 00000000000001ad
[ 56.170149] x7 : 00000000ffffffcc x6 : ffff8006ff768180
[ 56.175453] x5 : ffff8006ff768180 x4 : 0000000000000000
[ 56.180758] x3 : ffff8006ff76ef10 x2 : ffff8006ff768180
[ 56.186062] x1 : 3d2eccbaead8fb00 x0 : 0000000000000000
[ 56.191367] Call trace:
[ 56.193808] _regulator_disable+0xe0/0x1c0
[ 56.197899] regulator_disable+0x40/0x78
[ 56.201820] rcar_gen3_phy_usb2_power_off+0x3c/0x50
[ 56.206692] phy_power_off+0x48/0xd8
[ 56.210263] usb_phy_roothub_power_off+0x30/0x50
[ 56.214873] usb_phy_roothub_suspend+0x1c/0x50
[ 56.219311] hcd_bus_suspend+0x13c/0x168
[ 56.223226] generic_suspend+0x4c/0x58
[ 56.226969] usb_suspend_both+0x1ac/0x238
[ 56.230972] usb_suspend+0xcc/0x170
[ 56.234455] usb_dev_suspend+0x10/0x18
[ 56.238199] dpm_run_callback.isra.6+0x20/0x68
[ 56.242635] __device_suspend+0x110/0x308
[ 56.246637] async_suspend+0x24/0xa8
[ 56.250205] async_run_entry_fn+0x40/0xf8
[ 56.254210] process_one_work+0x1e0/0x320
[ 56.258211] worker_thread+0x40/0x450
[ 56.261867] kthread+0x124/0x128
[ 56.265094] ret_from_fork+0x10/0x18
[ 56.268661] ---[ end trace 86d7ec5de5c517af ]---
[ 56.273290] phy phy-ee080200.usb-phy.10: phy poweroff failed --> -5
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 549b6b55b005 ("phy: renesas: rcar-gen3-usb2: enable/disable independent irqs")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch fixes memory leak at error paths of the probe function.
In for_each_child_of_node, if the loop returns, the driver should
call of_put_node() before returns.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Fixes: 1233f59f745b237 ("phy: Renesas R-Car Gen2 PHY driver")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Since the previous code enabled/disabled the irqs both OHCI and EHCI,
it is possible to cause unexpected interruptions. To avoid this,
this patch creates multiple phy instances from phandle and
enables/disables independent irqs by the instances.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Tested-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
To implement multiple phy instances in the future, this patch uses
pdev's device pointer on dev_vdbg() instead of the phy's device
pointer.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch adds support for r8a77470 (RZ/G1C). We can reuse this driver for
initializing timing/interrupt generation registers.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch adds support for RZ/G1C (r8a77470) SoC. RZ/G1C SoC has a
PLL register shared between hsusb0 and hsusb1. Compared to other RZ/G1
and R-Car Gen2/3, USB Host needs to deassert the pll reset.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-and-Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch modifies rcar_gen3_init_otg() procedure to follow Figure
73.4 of "R-Car Series, 3rd Generation User's Manual: Hardware Rev.1.00".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Even if a board doesn't have otg pins connection, this hardware can
change the role by a register setting. So, this patch adds
"is_otg_channel" for it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
If uses_otg_pins is set to false, this driver 1) should disable otg
related interruptions, and 2) should not get ID pin signal, to avoid
unexpected behaviors. So, this patch adds conditions for it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch changes a condition about dr_mode. If a device node has
any dr_mode ("host", "peripheral" or "otg"), this driver allows to
set "is_otg_channel" to true. Also, this patch keeps the dr_mode
value for future use.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch unifies the OBINTEN handling to clean-up the code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Since All R-Car Gen3 SoCs have dedicated otg pins actually but
some boards don't use the otg pins (e.g. R-Car D3 Draak and R-Car E3
Ebisu), the driver should not choose SoC model base by using
rcar_gen3_phy_usb2_match_table's data. So, this patch checks a
"renesas,no-otg-pins" property to set the "uses_otg_pins".
Note that since r8a77995-draak.dts and r8a77990-ebisu.dts don't have
'dr_mode = "otg";' for now, if we apply this patch, no behavior
changes (the value of "uses_otg_pins" is false).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Since R-Car E3 and D3 have dedicated otg pins actually, "has_otg_pins"
is possible to misread in the future. So, this patch renames
has_otg_pins to uses_otg_pins.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch fixes and issue that the vbus_ctrl is disabled by
rcar_gen3_init_from_a_peri_to_a_host(), so a usb host cannot
supply the vbus.
Note that this condition will exit when the otg irq happens
even if we don't apply this patch.
Fixes: 9bb86777fb71 ("phy: rcar-gen3-usb2: add sysfs for usb role swap")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Use SPDX identifier for Renesas drivers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This PHY is still mostly undocumented -- the only documented registers
exist on R-Car V3H (R8A77980) SoC where this PHY stays in a powered-down
state after a reset and thus we must power it up for PCIe to work...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch adds support for r8a77965 (R-Car M3-N). This SoC has
dedicated pins.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
When USB is disabled, we get a link error for this driver
because of the added OTG support
drivers/phy/renesas/phy-rcar-gen3-usb2.o: In function `rcar_gen3_phy_usb2_probe':
phy-rcar-gen3-usb2.c:(.text+0x250): undefined reference to `of_usb_get_dr_mode_by_phy'
Other phy drivers select USB_COMMON for this, so let's do the same
here.
Fixes: 7e0540f41332 ("phy: rcar-gen3-usb2: check dr_mode for otg mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into usb-next
Chanwoo writes:
Update extcon for 4.15
Detailed description for this pull request:
1. Split out extcon header file for consumer and provider device
: The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect
the state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API
for both provider and consumer device driver. To clarify the meaning
of header file and to remove the wrong use-case on consumer device.
- include/linux/extcon-provider.h includes API for the provider device driver.
- include/linux/extcon.h includes the API for the consumer device driver.
2. Support the SmartDock accessory on extcon-max77843.c device driver
- Support the SmartDock accessory which detects following connectors
at the same time.
: USB host throught USB hub for mouse, keyboard and so on.
: MHL connector for video output.
: Charger connector for battery charging.
- It tested with Unitek Y-2165 MHL+OTG Hub Smart Phone Dock.
3. Fix the minor issue of extcon driver
- Delete the unneeded initialization in extcon-max14577.
- Make extcon_info static const in order to fix the warning.
|
|
This patch adds SoC-specific parameter to avoid reading/writing
specific registers wrongly if this driver runs on a SoC which doesn't
have dedicated pins (e.g. R-Car D3). This patch also changes the
value "has_otg" to "has_otg_pins" for slightly easier reading of
the code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch modifies the role_store() to use "enum phy_mode" instead
of the local "bool" for host/device mode selection.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The previous code assumed a channel has otg capability if a channel
has interrupt property. But, it is not good because:
- Battery charging feature also needs interrupt property.
- Some R-Car Gen3 SoCs (e.g. R-Car D3) don't have OTG capability.
So, this patch checks whether usb 2.0 host node has dr_mode property or
not. If it has 'dr_mode = "otg";', this driver enables otg capability.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect the
state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API for
both provider and consumer device driver. To clarify the meaning of
header file and to remove the wrong use-case on consumer device,
this patch separates into extcon.h and extcon-provider.h.
[Description for include/linux/{extcon.h|extcon-provider.h}]
- extcon.h includes the extcon API and data structure for extcon consumer
device driver. This header file contains the following APIs:
: Register/unregister the notifier to catch the change of extcon device
: Get the extcon device instance
: Get the extcon device name
: Get the state of each external connector
: Get the property value of each external connector
: Get the property capability of each external connector
- extcon-provider.h includes the extcon API and data structure for extcon
provider device driver. This header file contains the following APIs:
: Include 'include/linux/extcon.h'
: Allocate the memory for extcon device instance
: Register/unregister extcon device
: Set the state of each external connector
: Set the property value of each external connector
: Set the property capability of each external connector
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The USB 3.0 PHY modules of R-Car Gen3 SoCs have:
- Spread spectrum clock (ssc).
- Using USB 2.0 EXTAL clock instead of USB 3.0 clock.
- Enabling VBUS detection for usb3.0 peripheral.
So, this driver supports these features.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Adding vendor specific directories in phy to group
phy drivers under their respective vendor umbrella.
Also updated the MAINTAINERS file to reflect the correct
directory structure for phy drivers.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
