| Age | Commit message (Collapse) | Author |
|---|
|
The common layer phy exit callback ufs_qcom_phy_exit()
calls phy_power_off() that has no meaning when phy_power_off()
callback is already registered with the phy provider and
the consumer makes use of the same.
Instead, add a no-op specific phy_exit() callback for now
to add the exit sequence at a later point.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The phy init is meant to do phy initialization rather than
just getting the clock and regulator. Move these clock and
regulator get to probe(), to make room for actual phy
initialization sequence.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
remove() callback does a phy_power_off() only over the phy,
and nothing else now.
The phy_power_off() over the generic phy is called from the phy
consumer, and phy provider driver should not explicitly need to
call any phy ops.
So discard the remove callback for qcom-ufs phy platform drivers.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add a new compatible string for 14nm ufs phy present on msm8996
chipset. This phy is bit different from the legacy 14nm ufs phy
in terms of the clocks that are needed to be handled in the driver.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Different menthods pass around generic phy pointer to
extract device pointer. Instead, pass the device pointer
directly between function calls.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
kzalloc will issue its own error message including a dump_stack()
so remote the site specific message.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The phy_ops variables are never modified after initialized in these
drivers, so make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This change adds a support for a 14nm qcom-ufs phy that is
required in platforms that use ufs-qcom controller.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
