| Age | Commit message (Collapse) | Author |
|---|
|
callback
PHY drivers may try to access PHY registers in the ->reset() callback.
Invoke phy_pm_runtime_get_sync() before invoking the ->reset() callback
so that the PHY drivers don't have to enable clocks by themselves before
accessing PHY registers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add a new phy_ops *release* invoked when the consumer relinquishes the
PHY using phy_put/devm_phy_put. The initializations done by the PHY
driver in of_xlate call back can be can be cleaned up here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/phy/Kconfig:config GENERIC_PHY
drivers/phy/Kconfig: bool "PHY Core"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't remove module.h since the file is using other modular fcns
(to load other phy modules) even though the core support itself is
non-modular.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The phy framework is only allowing to configure the power state of the PHY
using the init and power_on hooks, and their power_off and exit
counterparts.
While it works for most, simple, PHYs supported so far, some more advanced
PHYs need some configuration depending on runtime parameters. These PHYs
have been supported by a number of means already, often by using ad-hoc
drivers in their consumer drivers.
That doesn't work too well however, when a consumer device needs to deal
with multiple PHYs, or when multiple consumers need to deal with the same
PHY (a DSI driver and a CSI driver for example).
So we'll add a new interface, through two funtions, phy_validate and
phy_configure. The first one will allow to check that a current
configuration, for a given mode, is applicable. It will also allow the PHY
driver to tune the settings given as parameters as it sees fit.
phy_configure will actually apply that configuration in the phy itself.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Currently the attempt to add support for Ethernet interface mode PHY
(MII/GMII/RGMII) will lead to the necessity of extending enum phy_mode and
duplicate there values from phy_interface_t enum (or introduce more PHY
callbacks) [1]. Both approaches are ineffective and would lead to fast
bloating of enum phy_mode or struct phy_ops in the process of adding more
PHYs for different subsystems which will make them unmaintainable.
As discussed in [1] the solution could be to introduce dual level PHYs mode
configuration - PHY mode and PHY submode. The PHY mode will define generic
PHY type (subsystem - PCIE/ETHERNET/USB_) while the PHY submode - subsystem
specific interface mode. The last is usually already defined in
corresponding subsystem headers (phy_interface_t for Ethernet, enum
usb_device_speed for USB).
This patch is cumulative change which refactors PHY framework code to
support dual level PHYs mode configuration - PHY mode and PHY submode. It
extends .set_mode() callback to support additional parameter "int submode"
and converts all corresponding PHY drivers to support new .set_mode()
callback declaration.
The new extended PHY API
int phy_set_mode_ext(struct phy *phy, enum phy_mode mode, int submode)
is introduced to support dual level PHYs mode configuration and existing
phy_set_mode() API is converted to macros, so PHY framework consumers do
not need to be changed (~21 matches).
[1] http://lkml.kernel.org/r/d63588f6-9ab0-848a-5ad4-8073143bd95d@ti.com
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
phy_init() and phy_exit() calls, and phy_power_on() and
phy_power_off() already accept NULL as valid PHY reference
and act as NOP. Extend same concept to phy runtime_pm APIs
to keep drivers (e.g. dwc3) code simple while dealing with
optional PHYs.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add following USB speed related PHY modes:
LS (Low Speed), FS (Full Speed), HS (High Speed), SS (Super Speed)
Speed related information is required by some QCOM PHY drivers
to program PHY monitor resume/remote-wakeup events in suspended
state. Speed is needed in order to set correct polarity of wakeup
events for detection. E.g. QUSB2 PHY monitors DP/DM line state
depending on whether speed is LS or FS/HS to detect resume.
Similarly QMP USB3 PHY in SS mode should monitor RX terminations
attach/detach and LFPS events depending on SSPHY is active or not.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Stefan Wahren reports a problem with a warning fix that was merged
for v4.15: we had lots of device nodes with a 'phys' property pointing
to a device node that is not compliant with the binding documented in
Documentation/devicetree/bindings/phy/phy-bindings.txt
This generally works because USB HCD drivers that support both the generic
phy subsystem and the older usb-phy subsystem ignore most errors from
phy_get() and related calls and then use the usb-phy driver instead.
However, it turns out that making the usb-nop-xceiv device compatible with
the generic-phy binding changes the phy_get() return code from -EINVAL to
-EPROBE_DEFER, and the dwc2 usb controller driver for bcm2835 now returns
-EPROBE_DEFER from its probe function rather than ignoring the failure,
breaking all USB support on raspberry-pi when CONFIG_GENERIC_PHY is
enabled. The same code is used in the dwc3 driver and the usb_add_hcd()
function, so a reasonable assumption would be that many other platforms
are affected as well.
I have reviewed all the related patches and concluded that "usb-nop-xceiv"
is the only USB phy that is affected by the change, and since it is by far
the most commonly referenced phy, all the other USB phy drivers appear
to be used in ways that are are either safe in DT (they don't use the
'phys' property), or in the driver (they already ignore -EPROBE_DEFER
from generic-phy when usb-phy is available).
To work around the problem, this adds a special case to _of_phy_get()
so we ignore any PHY node that is compatible with "usb-nop-xceiv",
as we know that this can never load no matter how much we defer. In the
future, we might implement a generic-phy driver for "usb-nop-xceiv"
and then remove this workaround.
Since we generally want older kernels to also want to work with the
fixed devicetree files, it would be good to backport the patch into
stable kernels as well (3.13+ are possibly affected), even though they
don't contain any of the patches that may have caused regressions.
Fixes: 014d6da6cb25 ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells
Fixes: c5bbf358b790 arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv
Fixes: 44e5dced2ef6 arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv
Fixes: f568f6f554b8 ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv
Fixes: d745d5f277bf ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv
Fixes: 915fbe59cbf2 ARM: dts: imx: Add missing #phy-cells to usb-nop-xceiv
Link: https://marc.info/?l=linux-usb&m=151518314314753&w=2
Link: https://patchwork.kernel.org/patch/10158145/
Cc: stable@vger.kernel.org
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Some quirky UDCs (like dwc3 on Exynos) need to have their phys calibrated e.g.
for using super speed. This patch adds a new phy_calibrate() method.
When the calibration should be used is dependent on actual chip.
In case of dwc3 on Exynos the calibration must happen after usb_add_hcd()
(while in host mode), because certain phy parameters like Tx LOS levels
and boost levels need to be calibrated further post initialization of xHCI
controller, to get SuperSpeed operations working. But an hcd must be
prepared first in order to pass it to usb_add_hcd(), so, in particular, dwc3
registers must be available first, and in order for the latter to happen
the phys must be initialized. This poses a chicken and egg problem if
the calibration were to be performed in phy_init(). To break the circular
dependency a separate method is added which can be called at a desired
moment after phy intialization.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The only use for this is for solving a hardware design problem in
usb of Rockchip RK3288.
Signed-off-by: Randy Li <ayaka@soulik.info>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The initial use for this is for PHYs that have a mode related to USB OTG.
There are several SoCs (e.g. TI OMAP and DA8xx) that have a mode setting
in the USB PHY to override OTG VBUS and ID signals.
Of course, the enum can be expaned in the future to include modes for
other types of PHYs as well.
Suggested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
|
|
In order to more flexibly support device tree bindings, allow drivers to
override the container of the child nodes. By default the device node of
the PHY provider is assumed to be the parent for children, but bindings
may decide to add additional levels for better organization.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
If phy_pm_runtime_get_sync failed but we already
enable regulator, current code return directly without
doing regulator_disable. This patch fix this problem
and cleanup err handle of phy_power_on to be more readable.
Fixes: 3be88125d85d ("phy: core: Support regulator ...")
Cc: <stable@vger.kernel.org> # v3.18+
Cc: Roger Quadros <rogerq@ti.com>
Cc: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
On driver detach, devm_phy_release() will put a refcount to
the phy, so gets a refconut to it before return.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a common checking in various drivers, so move the checking to
_of_phy_get().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Multi-port phys may have per port power supplies. Let's change phy
core to look for supply at the port level when multiple ports are
specified. To keep compatibility with the existing device tree board
descriptions for single-port phys we will continue looking up the
power supply at the parent node level
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Some generic drivers, such as ehci, may use multiple phys and for such
drivers referencing phy(s) by name(s) does not make sense. Instead of
inventing new naming schemes and using custom code to iterate through them,
such drivers are better of using nameless phy bindings and using this newly
introduced API to iterate through them.
Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
[kishon@ti.com: fix compilation errors]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Don't pass valid pointer to PTR_ERR, use PTR_ERR(phy) only when
IS_ERR(phy) is true.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
When phy_pm_runtime_get_sync() returns -ENOTSUPP, phy_exit() also returns
-ENOTSUPP if !phy->ops->exit. Fix it.
Also move the code to override ret close to the code we got ret.
I think it is less error prone this way.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
devm_phy_create() stores the pointer to the new PHY at the address
returned by devres_alloc(). The res parameter passed to devm_phy_match()
is therefore the location where the pointer to the PHY is stored, hence
it needs to be dereferenced before comparing to the match data in order
to find the correct match.
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The users of the old method are now converted to the new one.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[ kishon@ti.com : made phy-berlin-usb.c and phy-miphy28lp.c to use the updated
devm_phy_create API.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Separates registration of the phy and the lookup. The method
is copied from clkdev.c,
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Instead of using the node pointer of the PHY provider and then scanning its
child nodes to get a reference to the PHY, directly use the node pointer
present in of_phandle_args to get a reference to the PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
In case of multi-phy PHY providers, each PHY should be modeled as a sub
node of the PHY provider. Then each PHY will have a different node pointer
(node pointer of sub node) than that of PHY provider. Added this provision
in the PHY core.
Also fixed all drivers to use the updated API.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
|
|
Fixed of_phy_provider_lookup to return 'phy_provider' if _of_phy_get
passes the node pointer of the sub-node of phy provider node. This is
needed when phy provider implements multiple PHYs and each PHY is
modelled as the sub-node of PHY provider device node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
|
|
Some PHYs can be powered by an external power regulator.
e.g. USB_HS PHY on DRA7 SoC. Make the PHY core support a
power regulator.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Prevent resources from being freed twice in case device_add() call
fails within phy_create(). Also use ida_simple_remove() instead of
ida_remove() as we had used ida_simple_get() to allocate the ida.
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The kernel oopses in phy_lookup() due to 'phy->init_data' being NULL if we
register PHYs from a device tree probing driver and then call phy_get() on a
device that has no representation in the device tree (e.g. a PCI device).
Checking the pointer before dereferening it and skipping an interation if
it's NULL prevents this kernel oops.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adding devm_of_phy_get will allow to get phys by supplying a
pointer to the struct device_node instead of struct device.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Previously the of_phy_get function took a struct device * and
was declared static. It was impossible to call it from
another driver and thus it was impossible to get phy defined
for a given node. The old function was renamed to _of_phy_get
and was left for internal use. of_phy_get function was added
and it was exported. The function enables to get a phy for
a given device tree node.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The phy-core allows phy_init and phy_power_on to be called multiple times,
but before this patch -ENOSUPP from phy_pm_runtime_get_sync would be
propagated to the caller for the 2nd and later calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In various cases errors may be expected, ie probe-deferral or a call to
phy_get from a driver where the use of a phy is optional.
Rather then adding all sort of complicated checks for this, and/or adding
special functions like devm_phy_get_optional, simply don't log an error,
and let deciding if get_phy returning an error really should result in a
dev_err up to the caller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add devm_phy_optional_get and phy_optional_get, which should be used
when the phy is optional. They does not return an error when the phy
does not exist, rather they returns NULL, which is considered as a valid
phy, but results in NOPs when used with the consumer API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The common clock framework considers NULL a valid clock
reference. This makes handling optional clocks simple, in that if the
optional clock is not available, a NULL reference can be used in the
place of a real clock, simplifying the clock consumer.
Extend this concept to the phy consumer API. A NULL can be passed to
the release calls, the phy_init() and phy_exit() calls, and
phy_power_on() and phy_power_off() and a NOP is performed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
There were a few places where variables are initialized unncessarily.
Remove those initializations.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Increment 'init_count' only if the 'init' callback succeeded and decrement
'init_count' only if the 'exit' callback succeded. Increment 'power_count'
only if 'power_on' callback succeded and if it failed disable the clocks using
phy_pm_runtime_put_sync(). Also decrement 'power_count' only if 'power_off'
callback succeded and if it failed do not disable the clocks.
Reported-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
In case pm_runtime_get*() fails, it still
increments pm usage counter, so we *must*
make sure to pm_runtime_put() even in those
cases.
This patch fixes that mistake the same way
usbcore treats those possible failures.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
If this was called with a NULL "dev" then it lead to a NULL dereference
when we called dev_WARN(). I have changed it to WARN_ON() so that we
get a stack dump and can fix the caller.
The rest of this patch is just cleanup like returning directly instead
of having do-nothing gotos. Using descriptive labels instead of
GW-BASIC style "err0" and "err1". I also flipped the order of
put_device() and ida_remove() so they are a mirror reflection of the
order they were allocated.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'phy' was not being freed upon error in one of the cases.
Adjust the 'goto's to fix this.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The PHY framework provides a set of APIs for the PHY drivers to
create/destroy a PHY and APIs for the PHY users to obtain a reference to the
PHY with or without using phandle. For dt-boot, the PHY drivers should
also register *PHY provider* with the framework.
PHY drivers should create the PHY by passing id and ops like init, exit,
power_on and power_off. This framework is also pm runtime enabled.
The documentation for the generic PHY framework is added in
Documentation/phy.txt and the documentation for dt binding can be found at
Documentation/devicetree/bindings/phy/phy-bindings.txt
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
