| Age | Commit message (Collapse) | Author |
|---|
|
Rather than continue adding CPU-specific event maps, instead look up by
default in the PMUv3 event map and only fallback to the CPU-specific maps
if either the event isn't described by PMUv3, or it is described but
the PMCEID registers say that it is unsupported by the current CPU.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Managed resources in the driver should be automatically cleaned up on
driver detach. It's unnecessary to manually free/unmmap these resources.
One of the manual cleanup causes static checkers to complain.
The bug is reported by Dan Carpenter <dan.carpenter@oracle.com> in [1]
[1] https://www.spinics.net/lists/arm-kernel/msg593012.html
This patch gets rid of all the unnecessary manual cleanup and properly
unregister all the registered PMU devices by the driver on driver detach.
Signed-off-by: Tai Nguyen <ttnguyen@apm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Since the PMU register interface is banked per CPU, CPU PMU interrrupts
cannot be handled by a CPU other than the one with the PMU asserting the
interrupt. This means that migrating PMU SPIs, as we do during a CPU
hotplug operation doesn't make any sense and can lead to the IRQ being
disabled entirely if we route a spurious IRQ to the new affinity target.
This has been observed in practice on AMD Seattle, where CPUs on the
non-boot cluster appear to take a spurious PMU IRQ when coming online,
which is routed to CPU0 where it cannot be handled.
This patch passes IRQF_PERCPU for PMU SPIs and forcefully sets their
affinity prior to requesting them, ensuring that they cannot
be migrated during hotplug events. This interacts badly with the DB8500
erratum workaround that ping-pongs the interrupt affinity from the handler,
so we avoid passing IRQF_PERCPU in that case by allowing the IRQ flags
to be overridden in the platdata.
Fixes: 3cf7ee98b848 ("drivers/perf: arm_pmu: move irq request/free into probe")
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The check for column exclusion did not verify that the event being
checked was an L2 event, and not a software event.
Software events should not be checked for column exclusion.
This resulted in a group with both software and L2 events sometimes
incorrectly rejecting the L2 event for column exclusion and
not counting it.
Add a check for PMU type before applying column exclusion logic.
Fixes: 21bdbb7102edeaeb ("perf: add qcom l2 cache perf events driver")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Neil Leeder <nleeder@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Merge in arm64 ACPI RAS support (APEI/GHES) from Tyler Baicar.
|
|
This patch adds support for SoC-wide (AKA uncore) Performance Monitoring
Unit version 3.
It can support up to
- 2 IOB PMU instances
- 8 L3C PMU instances
- 2 MCB PMU instances
- 8 MCU PMU instances
and these PMUs support 64 bit counter
Signed-off-by: Hoan Tran <hotran@apm.com>
[Mark: stop counters in _xgene_pmu_isr()]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: make xgene_pmu_v3_ops static]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This patch moves PMU leaf functions into a function pointer structure.
It helps code maintain and expasion easier.
Signed-off-by: Hoan Tran <hotran@apm.com>
[Mark: remove redundant cast]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: make xgene_pmu_ops static]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This patch parses PMU Subnode from a match table.
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
All PMU drivers are going to depend on PERF_EVENTS, so let's make this
dependency common and simplify the individual Kconfig entries.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We saw perf IRQ init failures when running Linux kernel in an ACPI
guest without PMU (i.e. pmu=off). This is because perf IRQ is not
present when pmu=off, but arm_pmu_acpi still tries to register
or unregister GSI. This patch addresses the problem by checking
gicc->performance_interrupt. If it is 0, which is the value set
by qemu when pmu=off, we skip the IRQ register/unregister process.
[ 4.069470] bc00: 0000000000040b00 ffff0000089db190
[ 4.070267] [<ffff000008134f80>] enable_percpu_irq+0xdc/0xe4
[ 4.071192] [<ffff000008667cc4>] arm_perf_starting_cpu+0x108/0x10c
[ 4.072200] [<ffff0000080cbdd4>] cpuhp_invoke_callback+0x14c/0x4ac
[ 4.073210] [<ffff0000080ccd3c>] cpuhp_thread_fun+0xd4/0x11c
[ 4.074132] [<ffff0000080f1394>] smpboot_thread_fn+0x1b4/0x1c4
[ 4.075081] [<ffff0000080ec90c>] kthread+0x10c/0x138
[ 4.075921] [<ffff0000080833c0>] ret_from_fork+0x10/0x50
[ 4.076947] genirq: Setting trigger mode 4 for irq 43 failed
(gic_set_type+0x0/0x74)
Signed-off-by: Wei Huang <wei@redhat.com>
[will: add comment justifying deviation from ACPI spec, removed redundant hunk]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This patch adds framework code to handle parsing PMU data out of the
MADT, sanity checking this, and managing the association of CPUs (and
their interrupts) with appropriate logical PMUs.
For the time being, we expect that only one PMU driver (PMUv3) will make
use of this, and we simply pass in a single probe function.
This is based on an earlier patch from Jeremy Linton.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Now that we've split the pdev and DT probing logic from the runtime
management, let's move the former into its own file. We gain a few lines
due to the copyright header and includes, but this should keep the logic
clearly separated, and paves the way for adding ACPI support in a
similar fashion.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
[will: rename nr_irqs to avoid conflict with global variable]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Currently we request (and potentially free) all IRQs for a given PMU in
cpu_pmu_init(). This works for platform/DT probing today, but it doesn't
fit ACPI well as we don't have all our affinity data up-front.
In preparation for ACPI support, fold the IRQ request/free into
arm_pmu_device_probe(), which will remain specific to platform/DT
probing.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Currently we have functions to request/free all IRQs for a given PMU.
While this works today, this won't work for ACPI, where we don't know
the full set of IRQs up front, and need to request them separately.
To enable supporting ACPI, this patch splits out the cpu-local
request/free into new functions, allowing us to request/free individual
IRQs.
As this makes it possible/necessary to request a PPI once per cpu, an
additional check is added to detect mismatched PPIs. This shouldn't
matter for the DT / platform case, as we check this when parsing.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
For historical reasons, portions of the arm_pmu code use a cpu_pmu_
prefix rather than an armpmu_ prefix. While a minor annoyance, this
hasn't been a problem thusfar.
However, to enable ACPI support, we'll need to expose a few things in
header files, and we should aim to keep those consistently namespaced.
In preparation for exporting our IRQ request/free functions, rename
these to have an armpmu_ prefix. For consistency, the 'cpu_pmu'
parameter is also renamed to 'armpmu'.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
In armpmu_dispatch_irq() we look at arm_pmu::plat_device to acquire
platdata, so that we can defer to platform-specific IRQ handling,
required on some 32-bit parts. With the advent of ACPI we won't always
have a platform_device, and so we must avoid trying to dereference
fields from it.
This patch fixes up armpmu_dispatch_irq() to avoid doing so, introducing
a new armpmu_get_platdata() helper.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The ARM PMU framework code always uses armpmu_dispatch_irq as its common
IRQ handler. Passing this down from cpu_pmu_init() is somewhat
pointless, and gets in the way of refactoring.
This patch makes cpu_pmu_request_irqs() always use armpmu_dispatch_irq
as the handler when requesting IRQs, and removes the handler parameter
from its prototype.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Currently arm_pmu_device_probe contains probing logic specific to the
platform_device infrastructure, and some logic required to safely
register the PMU with various systems.
This patch factors out the logic relating to the registration of the
PMU. This makes arm_pmu_device_probe a little easier to read, and will
make it easier to reuse the logic for an ACPI-specific probing
mechanism.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Given we always want to initialise common fields on an allocated PMU,
this patch folds this common initialisation into armpmu_alloc(). This
will make it simpler to reuse this code for an ACPI-specific probe path.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We expect an ARM PMU's init function to have a particular prototype,
which we open-code in a few places. This is less than ideal, considering
that we cast a void value to this type in one location, and a mismatch
could easily be missed.
Add a typedef so that we can ensure this is consistent.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We currently disable the PMU temporarily in armpmu_add(). We may have
required this historically, but the perf core always disables an event's
PMU when calling event::pmu::add(), so this is not necessary.
We don't do similarly in armpmu_del(), or elsewhere, so this is
unnecessary and inconsistent, and only serves to confuse the reader.
Remove the pointless disable, simplifying armpmu_add() in the process.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This adds a new dynamic PMU to the Perf Events framework to program
and control the L3 cache PMUs in some Qualcomm Technologies SOCs.
The driver supports a distributed cache architecture where the overall
cache for a socket is comprised of multiple slices each with its own PMU.
Access to each individual PMU is provided even though all CPUs share all
the slices. User space needs to aggregate to individual counts to provide
a global picture.
The driver exports formatting and event information to sysfs so it can
be used by the perf user space tools with the syntaxes:
perf stat -a -e l3cache_0_0/read-miss/
perf stat -a -e l3cache_0_0/event=0x21/
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Agustin Vega-Frias <agustinv@codeaurora.org>
[will: fixed sparse issues]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
For historical reasons, we lazily request and free interrupts in the
arm pmu driver. This requires us to refcount use of the pmu (by way of
counting the active events) in order to request/free interrupts at the
correct times, which complicates the driver somewhat.
The existing logic is flawed, as it only considers currently online CPUs
when requesting, freeing, or managing the affinity of interrupts.
Intervening hotplug events can result in erroneous IRQ affinity, online
CPUs for which interrupts have not been requested, or offline CPUs whose
interrupts are still requested.
To fix this, this patch splits the requesting of interrupts from any
per-cpu management (i.e. per-cpu enable/disable, and configuration of
cpu affinity). We now request all interrupts up-front at probe time (and
never free them, since we never unregister PMUs).
The management of affinity, and per-cpu enable/disable now happens in
our cpu hotplug callback, ensuring it occurs consistently. This means
that we must now invoke the CPU hotplug callback at boot time in order
to configure IRQs, and since the callback also resets the PMU hardware,
we can remove the duplicate reset in the probe path.
This rework renders our event refcounting unnecessary, so this is
removed.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: make armpmu_get_cpu_irq static]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
When requesting or freeing interrupts, we use platform_get_irq() to find
relevant irqs, backing this up with additional information in an
optional irq_affinity table.
This means that our irq request and free paths are tied to a
platform_device, and our request path must jump through a number of
hoops in order to determine the required affinity of each interrupt.
Given that the affinity must be static, we can compute the affinity once
up-front at probe time, simplifying the irq request and free paths. By
recording interrupts in a per-cpu data structure, we simplify a few
paths, and permit a subsequent rework of the request and free paths.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: rename local nr_irqs variable to avoid conflict with global]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
For historical reasons, we allocate per-cpu data associated with a PMU
rather late, in cpu_pmu_init, after we've parsed whatever hardware
information we were provided with.
In order to allow use to store some per-cpu data early in the probe
path, we need to allocate (and initialise) the per-cpu data earlier.
This patch reworks the way we allocate the pmu and associated per-cpu
data in order to make that possible.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: make armpmu_{alloc,free} static
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
<linux/sched/clock.h>
We are going to split <linux/sched/clock.h> out of <linux/sched.h>, which
will have to be picked up from other headers and .c files.
Create a trivial placeholder <linux/sched/clock.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Adds perf events support for L2 cache PMU.
The L2 cache PMU driver is named 'l2cache_0' and can be used
with perf events to profile L2 events such as cache hits
and misses on Qualcomm Technologies processors.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Neil Leeder <nleeder@codeaurora.org>
[will: minimise nesting in l2_cache_associate_cpu_with_cluster]
[will: use kstrtoul for unsigned long, remove redunant .owner setting]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
I ran into a build error when I disabled CONFIG_ACPI and tried to
compile this driver:
drivers/perf/xgene_pmu.c:1242:1: warning: data definition has no type or storage class
MODULE_DEVICE_TABLE(of, xgene_pmu_of_match);
^
drivers/perf/xgene_pmu.c:1242:1: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE' [-Werror=implicit-int]
Include module.h for the MODULE_DEVICE_TABLE macro that's
implicitly included through ACPI.
Tested-by: Tai Nguyen <ttnguyen@apm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In acpi_get_pmu_hw_inf we pass the address of a local variable to IS_ERR(),
which doesn't make sense, as the pointer must be a real, valid pointer.
This doesn't cause a functional problem, as IS_ERR() will evaluate as
false, but the check is bogus and causes static checkers to complain.
Remove the bogus check.
The bug is reported by Dan Carpenter <dan.carpenter@oracle.com> in [1]
[1] https://www.spinics.net/lists/arm-kernel/msg535957.html
Signed-off-by: Tai Nguyen <ttnguyen@apm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"It's a bit all over the place this time with no "killer feature" to
speak of. Support for mismatched cache line sizes should help people
seeing whacky JIT failures on some SoCs, and the big.LITTLE perf
updates have been a long time coming, but a lot of the changes here
are cleanups.
We stray outside arch/arm64 in a few areas: the arch/arm/ arch_timer
workaround is acked by Russell, the DT/OF bits are acked by Rob, the
arch_timer clocksource changes acked by Marc, CPU hotplug by tglx and
jump_label by Peter (all CC'd).
Summary:
- Support for execute-only page permissions
- Support for hibernate and DEBUG_PAGEALLOC
- Support for heterogeneous systems with mismatches cache line sizes
- Errata workarounds (A53 843419 update and QorIQ A-008585 timer bug)
- arm64 PMU perf updates, including cpumasks for heterogeneous systems
- Set UTS_MACHINE for building rpm packages
- Yet another head.S tidy-up
- Some cleanups and refactoring, particularly in the NUMA code
- Lots of random, non-critical fixes across the board"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (100 commits)
arm64: tlbflush.h: add __tlbi() macro
arm64: Kconfig: remove SMP dependence for NUMA
arm64: Kconfig: select OF/ACPI_NUMA under NUMA config
arm64: fix dump_backtrace/unwind_frame with NULL tsk
arm/arm64: arch_timer: Use archdata to indicate vdso suitability
arm64: arch_timer: Work around QorIQ Erratum A-008585
arm64: arch_timer: Add device tree binding for A-008585 erratum
arm64: Correctly bounds check virt_addr_valid
arm64: migrate exception table users off module.h and onto extable.h
arm64: pmu: Hoist pmu platform device name
arm64: pmu: Probe default hw/cache counters
arm64: pmu: add fallback probe table
MAINTAINERS: Update ARM PMU PROFILING AND DEBUGGING entry
arm64: Improve kprobes test for atomic sequence
arm64/kvm: use alternative auto-nop
arm64: use alternative auto-nop
arm64: alternative: add auto-nop infrastructure
arm64: lse: convert lse alternatives NOP padding to use __nops
arm64: barriers: introduce nops and __nops macros for NOP sequences
arm64: sysreg: replace open-coded mrs_s/msr_s with {read,write}_sysreg_s
...
|
|
https://github.com/AppliedMicro/xgene-next into next/drivers
Pull "X-Gene driver changes queued for v4.9" from Duc Dang:
This patch set includes:
+ X-Gene SoC Performance Monitoring Unit (PMU) driver
* tag 'xgene-drivers-for-4.9' of https://github.com/AppliedMicro/xgene-next:
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
|
|
In preparation for ACPI support, add a pmu_probe_info table to
the arm_pmu_device_probe() call. This table gets used when
probing in the absence of a devicetree node for PMU.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This patch adds a driver for the SoC-wide (AKA uncore) PMU hardware
found in APM X-Gene SoCs.
Signed-off-by: Tai Nguyen <ttnguyen@apm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
|
|
In systems with heterogeneous CPUs, there are multiple logical CPU PMUs,
each of which covers a subset of CPUs in the system. In some cases
userspace needs to know which CPUs a given logical PMU covers, so we'd
like to expose a cpumask under sysfs, similar to what is done for uncore
PMUs.
Unfortunately, prior to commit 00e727bb389359c8 ("perf stat: Balance
opening and reading events"), perf stat only correctly handled a cpumask
holding a single CPU, and only when profiling in system-wide mode. In
other cases, the presence of a cpumask file could cause perf stat to
behave erratically.
Thus, exposing a cpumask file would break older perf binaries in cases
where they would otherwise work.
To avoid this issue while still providing userspace with the information
it needs, this patch exposes a differently-named file (cpus) under
sysfs. New tools can look for this and operate correctly, while older
tools will not be adversely affected by its presence.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Now that the 32-bit and 64-bit perf backends use the common groups
directly, remove the fallback and no longer allow the groups array to be
overridden.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
In preparation for adding common attribute groups, add an array of
attribute group pointers to arm_pmu, which will be used if the
backend hasn't already set pmu::attr_groups.
Subsequent patches will move backends over to using these, before adding
common fields.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
As declared by the chief penguin, and enforced by the NO_IRQ brigade,
IRQ0 doesn't exist, and is considered as an error (no irq).
Unfortunately, the arm_pmu driver still considers it as valid in
a large number of cases. Let's fix this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160817171420.sdwk2qivxunzryz4@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Patch 7f1d642fbb5c ("drivers/perf: arm-pmu: Fix handling of SPI lacking
interrupt-affinity property") unintended also fixes perf_event support
for bcm2835 which doesn't have PMU interrupts. Unfortunately this change
introduce a NULL pointer dereference on bcm2835, because irq_is_percpu
always expected to be called with a valid IRQ. So fix this regression
by validating the IRQ before.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 7f1d642fbb5c ("drivers/perf: arm-pmu: Fix handling of SPI lacking "interrupt-affinity" property")
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In case of a IRQ type mismatch in of_pmu_irq_cfg() the
device node for interrupt affinity isn't freed. So fix this
issue by calling of_node_put().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: fa8ad7889d83 ("arm: perf: factor arm_pmu core out to drivers")
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Patch 19a469a58720 ("drivers/perf: arm-pmu: Handle per-interrupt
affinity mask") added support for partitionned PPI setups, but
inadvertently broke setups using SPIs without the "interrupt-affinity"
property (which is the case for UP platforms).
This patch restore the broken functionnality by testing whether the
interrupt is percpu or not instead of relying on the using_spi flag
that really means "SPI *and* interrupt-affinity property".
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 19a469a58720 ("drivers/perf: arm-pmu: Handle per-interrupt affinity mask")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
arm_pmu_mutex is never held long and we don't want to sleep while the
lock is being held as it's executed in the context of hotplug notifiers.
So it can be converted to a simple spinlock instead.
Without this patch we get the following warning:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620
in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/2
no locks held by swapper/2/0.
irq event stamp: 381314
hardirqs last enabled at (381313): _raw_spin_unlock_irqrestore+0x7c/0x88
hardirqs last disabled at (381314): cpu_die+0x28/0x48
softirqs last enabled at (381294): _local_bh_enable+0x28/0x50
softirqs last disabled at (381293): irq_enter+0x58/0x78
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.7.0 #12
Call trace:
dump_backtrace+0x0/0x220
show_stack+0x24/0x30
dump_stack+0xb4/0xf0
___might_sleep+0x1d8/0x1f0
__might_sleep+0x5c/0x98
mutex_lock_nested+0x54/0x400
arm_perf_starting_cpu+0x34/0xb0
cpuhp_invoke_callback+0x88/0x3d8
notify_cpu_starting+0x78/0x98
secondary_start_kernel+0x108/0x1a8
This patch converts the mutex to spinlock to eliminate the above
warnings. This constraints pmu->reset to be non-blocking call which is
the case with all the ARM PMU backends.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Fixes: 37b502f121ad ("arm/perf: Fix hotplug state machine conversion")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
|
|
Mark Rutland pointed out that this commit is incomplete:
7d88eb695a1f ("arm/perf: Convert to hotplug state machine")
The problem is that:
> We may have multiple PMUs (e.g. two in big.LITTLE systems), and
> __oprofile_cpu_pmu only contains one of these. So this conversion is not
> correct.
>
> We were relying on the notifier list implicitly containing a list of
> those PMUs. It seems like we need an explicit list here.
>
> We keep __oprofile_cpu_pmu around for legacy 32-bit users of OProfile
> (on non-hetereogeneous systems), and that's all that the variable should
> be used for.
Introduce arm_pmu_list to correctly handle multiple PMUs in the system.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-tip-commits@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160719111733.GA22911@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Straight forward conversion w/o bells and whistles.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153335.794097159@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
On a big-little system, PMUs can be wired to CPUs using per CPU
interrups (PPI). In this case, it is important to make sure that
the enable/disable do happen on the right set of CPUs.
So instead of relying on the interrupt-affinity property, we can
use the actual percpu affinity that DT exposes as part of the
interrupt specifier. The DT binding is also updated to reflect
the fact that the interrupt-affinity property shouldn't be used
in that case.
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
