| Age | Commit message (Collapse) | Author |
|---|
|
The .get_socket callback is never used by the PCMCIA core, therefore remove
it.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Don't waste cpu time in yenta interrupt handler when the interrupt was for
another device.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
It's simple, and it's a good debugging aid.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Adds better support for the CB-710, CB-712, CB-720 and CB-722 bridges from EnE
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Support some more TI cardbus bridges. most of them are multifunction
devices which adds 1394 controllers, smartcard readers etc. this could
also help with the various problems with the XX21 controllers seen on the
linux-pcmcia list.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
pci_set_power_state is not needed, as we call pci_enable_device() somewhere
else. Also, the resource we write to PCI_BASE_ADDRESS_0 needs to be converted
to bus-centric view first.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
In interrupt probing (both ISA and PCI) the bridge control register is used
to change interrupt routing to ISA or PCI by changing bit 7. But this bit
only controls the routing of card functional interrupts, not the CSC
interrupts which are used for interrupt probing.
A bad side effect of messing with this register in yenta_probe_irq() is
that it can lead to irq storms if a card is inserted and already powered by
the BIOS.
Usage in yenta_sock_init() and yenta_config_init() seem to be fishy as well.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Echo Audio cardbus products are known to be incompatible with EnE bridges.
in order to maybe solve the problem a EnE specific test bit has to be set,
another cleared...but other setups have a good chance to break when just
forcing the bits. so do the whole thingy automatically.
The patch adds a hook in cb_alloc() that allows special tuning for the
different chipsets. for ene just match the Echo products and set/clear the
test bits, defaults to do the same thing as w/o the patch to not break
working setups.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
And mention 'pci=assign-busses' as a possible fix.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
In some cases, especially on modern laptops with a lot of PCI and
cardbus bridges, we're unable to assign correct secondary/subordinate
bus numbers to all cardbus bridges due to BIOS limitations unless
we are using "pci=assign-busses" boot option.
So some cardbus controllers may not have attached subordinate pci_bus
structure, and yenta driver must cope with it - just ignore such cardbus
bridges.
For example, see https://bugzilla.novell.com/show_bug.cgi?id=113778
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
extend cb_writel(), exca_writeb(), exca_writel() to do a read[lb]() after
the write[lb]() to avoid possible problem with PCI write posting.
Seems to fix Bug #5061.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Share code between setup-bus.c and yenta_socket.c: use the write-out code of
resources to the bridge also in yenta_socket.c, as it provides useful debug
output. In addition, it fixes the bug that the CPU-centric resource view
might need to be transferred to the PCI-centric view: setup-bus.c does that,
while yenta-socket.c did not.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
ToPIC95 brides (and maybe some other too) require to use the ExCA registers
to power up the socket if a 16bit card is pluged. allow socket drivers to
set a flag so that yenta does just that. also clean up yenta_get_status()
a bit to use the new yenta_get_power() function.
Side note: ToPIC97 bridges (at least in Rev.5 i have) don't require this.
Ryan Underwood <nemesis-lists@icequake.net> said:
According to the mail that David Hinds received from a Toshiba engineer,
ToPIC95 and 97 do require this, and ToPIC100 does not. Maybe you have a
later revision.
For all chips, 16-bit cards can be enabled through ExCA. So doesn't it
make sense just to make this the default behavior for all Toshiba chips,
to avoid corner cases showing up later?
Daniel responded:
I disagree with ryan to change anything for topic97 bridges. they work.
and I couldn't find (read google) any report of a topic97 breaking on
applying power with the CB registers.
I'm having several toshba notebooks at work (and home) with topic95,97,100
bridges. Only the ones with a topic95 didn't work.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
In yenta_socket, we default to using the resource setting of the CardBus
bridge. However, this is a PCI-bus-centric view of resources and thus needs
to be converted to generic resources first. Therefore, add a call to
pcibios_bus_to_resource() call in between. This function is a mere wrapper on
x86 and friends, however on some others it already exists, is added in this
patch (alpha, arm, ppc, ppc64) or still needs to be provided (parisc -- where
is its pcibios_resource_to_bus() ?).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Recent changes (well, dating from 12 July) have broken cardbus on my
powerbook: I get 3 messages saying "no resource of type xxx available,
trying to continue", and if I plug in my wireless card, it complains
that there are no resources allocated to the card. This all worked in
2.6.12.
Looking at the code in yenta_socket.c, function yenta_allocate_res,
it's obvious what is wrong: if we get to line 639 (i.e. there wasn't a
usable preassigned resource), we will always flow through to line 668,
which is the printk that I was seeing, even if a resource was
successfully allocated. It looks to me as though there should be a
return statement after the two config_writel's in each of the 3
branches of the if statements, so that the function returns after
successfully setting up the resource.
The patch below adds these return statements, and with this patch,
cardbus works on my powerbook once again.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
ACPI is wrong. Devices should not release their IRQ's on suspend and
re-aquire them on resume. ACPI should just re-init the IRQ controller
instead of breaking most drivers very subtly.
Breakage reported by Hugh Dickins <hugh@veritas.com>
Undo: d8c4b4195c7d664baf296818bf756775149232d3
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Resume doesn't seem to work without.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
The current CardBus window allocation code in yenta_socket is unable to handle
the transparent PCI-bridge handling update in 2.6.13. We need to check _all_
resources of a given type to find the best one suitable for CardBus windows,
not just the first one.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
drivers/pci/setup-bus.c enumerates the CardBus windows (bus->resources[])
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
If the CardBus windows were pre-configured and the CardBus bridge is behind a
transparent PCI-PCI bridge, pci_find_parent_resource() might return a
different resource than the real parent if it is called before the window is
determined. Therefore, move that call around.
Also fix return of value in void function.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Drivers should do this:
.suspend()
pci_disable_device()
.resume()
pci_enable_device()
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
If probing for the correct interrupt fails on yenta bridges, the driver falls
back to polling for interrupt actions. However, CardBus cards cannot be used
then.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
As a follow-up, remove the inclusion of pcmcia/version.h in many files.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
On Mon, Jun 20, 2005 at 07:15:34PM +1000, Grant Coady wrote:
> Yenta: CardBus bridge found at 0000:00:0b.0 [1179:0001]
> yenta 0000:00:0b.0: Preassigned resource 0 busy, reconfiguring...
In -mm1 the cardbus resources might be assigned in
pci_assign_unassigned_resources() pass. From your dmesg:
PCI: Bus 2, cardbus bridge: 0000:00:0b.0
IO window: 00002000-00002fff
IO window: 00003000-00003fff
PREFETCH window: 12000000-13ffffff
MEM window: 14000000-15ffffff
Then yenta_allocate_res() tries to assign these resources again and,
naturally, fails.
This adds check for already assigned cardbus resources.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
- make boot-up card recognition more reliable (ie. redo interrogation
always if there is no valid 'card inserted' state) (and yes, i saw it
happening on an o2micro controller that both CB_CBARD and CB_16BITCARD
bits were set at the same time)
- also redo interrogation before probing the ISA interrupts. it's safer
to do the probing with the socket in a clean state.
- make card insert detect more reliable. yenta_get_status() now returns
SS_PENDING as long as the card is not completley inserted and one of the
voltage bits is set. also !CB_CBARD doesn't mean CB_16BITCARD. there is
CB_NOTACARD as well, so make an explicit check for CB_16BITCARD.
- for TI bridges: disable IRQs during power-on. in all-serial and tied
interrupt mode the interrupts are always disabled for single-slot
controllers. for two-slot contollers the disabling is only done when the
other slot is empty. to force disabling there is a new module parameter
now: pwr_irqs_off=Y (which is a regression for working setups. that's
why it's an option, only use when required)
- modparm to disable ISA interrupt probing (isa_probe, defaults to on)
- remove unneeded code/cleanups (ie. merge yenta_events() into
yenta_interrupts())
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
