summaryrefslogtreecommitdiff
path: root/drivers/pci
AgeCommit message (Collapse)Author
2011-11-23Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: PCI hotplug: shpchp: don't blindly claim non-AMD 0x7450 device IDs PCI: pciehp: wait 100 ms after Link Training check PCI: pciehp: wait 1000 ms before Link Training check PCI: pciehp: Retrieve link speed after link is trained PCI: Let PCI_PRI depend on PCI PCI: Fix compile errors with PCI_ATS and !PCI_IOV PCI / ACPI: Make acpiphp ignore root bridges using PCIe native hotplug
2011-11-14PCI hotplug: shpchp: don't blindly claim non-AMD 0x7450 device IDsBjorn Helgaas
Previously we claimed device ID 0x7450, regardless of the vendor, which is clearly wrong. Now we'll claim that device ID only for AMD. I suspect this was just a typo in the original code, but it's possible this change will break shpchp on non-7450 AMD bridges. If so, we'll have to fix them as we find them. Reference: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=638863 Reported-by: Ralf Jung <ralfjung-e@gmx.de> Cc: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-11-11PCI: pciehp: wait 100 ms after Link Training checkKenji Kaneshige
If the port supports Link speeds greater than 5.0 GT/s, we must wait for 100 ms after Link training completes before sending configuration request. Acked-by: Yinghai Lu <yinghai@kernel.org> Tested-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-11-11PCI: pciehp: wait 1000 ms before Link Training checkKenji Kaneshige
We need to wait for 1000 ms after Data Link Layer Link Active (DLLLA) bit reads 1b before sending configuration request. Currently pciehp does this wait after checking Link Training (LT) bit. But we need it before checking LT bit because LT is still set even after DLLLA bit is set on some platforms. Acked-by: Yinghai Lu <yinghai@kernel.org> Tested-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-11-07PCI: pciehp: Retrieve link speed after link is trainedYinghai Lu
During hot plug, board_added will call pciehp_power_on_slot(). But link speed is updated in pciehp_power_on_slot(). We should not update link speed there, because that is too early. So move the link speed update to pciehp_check_link_status() after making sure the link has been trained. -v2: fix compile warning that Kenji found. Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com> Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-11-06Merge branch 'modsplit-Oct31_2011' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux * 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits) Revert "tracing: Include module.h in define_trace.h" irq: don't put module.h into irq.h for tracking irqgen modules. bluetooth: macroize two small inlines to avoid module.h ip_vs.h: fix implicit use of module_get/module_put from module.h nf_conntrack.h: fix up fallout from implicit moduleparam.h presence include: replace linux/module.h with "struct module" wherever possible include: convert various register fcns to macros to avoid include chaining crypto.h: remove unused crypto_tfm_alg_modname() inline uwb.h: fix implicit use of asm/page.h for PAGE_SIZE pm_runtime.h: explicitly requires notifier.h linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h miscdevice.h: fix up implicit use of lists and types stop_machine.h: fix implicit use of smp.h for smp_processor_id of: fix implicit use of errno.h in include/linux/of.h of_platform.h: delete needless include <linux/module.h> acpi: remove module.h include from platform/aclinux.h miscdevice.h: delete unnecessary inclusion of module.h device_cgroup.h: delete needless include <linux/module.h> net: sch_generic remove redundant use of <linux/module.h> net: inet_timewait_sock doesnt need <linux/module.h> ... Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in - drivers/media/dvb/frontends/dibx000_common.c - drivers/media/video/{mt9m111.c,ov6650.c} - drivers/mfd/ab3550-core.c - include/linux/dmaengine.h
2011-11-06Merge branch 'trivial' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild * 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: scsi: drop unused Kconfig symbol pci: drop unused Kconfig symbol stmmac: drop unused Kconfig symbol x86: drop unused Kconfig symbol powerpc: drop unused Kconfig symbols powerpc: 40x: drop unused Kconfig symbol mips: drop unused Kconfig symbols openrisc: drop unused Kconfig symbols arm: at91: drop unused Kconfig symbol samples: drop unused Kconfig symbol m32r: drop unused Kconfig symbol score: drop unused Kconfig symbols sh: drop unused Kconfig symbol um: drop unused Kconfig symbol sparc: drop unused Kconfig symbol alpha: drop unused Kconfig symbol Fix up trivial conflict in drivers/net/ethernet/stmicro/stmmac/Kconfig as per Michal: the STMMAC_DUAL_MAC config variable is still unused and should be deleted.
2011-10-31pci: add module.h to files implicitly relying on its presence.Paul Gortmaker
These were getting module.h implicitly from device.h but we want to clean that up, so we fix it here to avoid things like: pci/slot.c: In function ‘pci_hp_create_module_link’: pci/slot.c:383: error: ‘module_kset’ undeclared (first use in this function) Similarly, rpadlpar_core.c is modular, so add module.h to its includes. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31pci: Fix files needing export.h for EXPORT_SYMBOL/THIS_MODULEPaul Gortmaker
They were implicitly getting it from device.h --> module.h but we want to clean that up. So add the minimal header for these macros. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31pci: drop unused Kconfig symbolPaul Bolle
There's no other Kconfig symbol that depends on XEN_PCIDEV_FE_DEBUG. Neither is there anything that uses CONFIG_XEN_PCIDEV_FE_DEBUG. Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Michal Marek <mmarek@suse.cz>
2011-10-31PCI: Let PCI_PRI depend on PCIJoerg Roedel
This avoids the PCI_PRI question in 'make config' when PCI is not selected. Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-31PCI / ACPI: Make acpiphp ignore root bridges using PCIe native hotplugRafael J. Wysocki
If the kernel has requested control of the PCIe native hotplug feature for a given root complex, the acpiphp driver should not try to handle that root complex and it should leave it to pciehp. Failing to do so causes problems to happen if acpiphp is loaded before pciehp on such systems. To address this issue make find_root_bridges() ignore PCIe root complexes with PCIe native hotplug enabled and make add_bridge() return error code if PCIe native hotplug is enabled for the given root port. This causes acpiphp to refuse to load if PCIe native hotplug is enabled for all complexes and to refuse binding to the root complexes with PCIe native hotplug is enabled. Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-28Merge branch 'next-rebase' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci * 'next-rebase' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: PCI: Clean-up MPS debug output pci: Clamp pcie_set_readrq() when using "performance" settings PCI: enable MPS "performance" setting to properly handle bridge MPS PCI: Workaround for Intel MPS errata PCI: Add support for PASID capability PCI: Add implementation for PRI capability PCI: Export ATS functions to modules PCI: Move ATS implementation into own file PCI / PM: Remove unnecessary error variable from acpi_dev_run_wake() PCI hotplug: acpiphp: Prevent deadlock on PCI-to-PCI bridge remove PCI / PM: Extend PME polling to all PCI devices PCI quirk: mmc: Always check for lower base frequency quirk for Ricoh 1180:e823 PCI: Make pci_setup_bridge() non-static for use by arch code x86: constify PCI raw ops structures PCI: Add quirk for known incorrect MPSS PCI: Add Solarflare vendor ID and SFC4000 device IDs
2011-10-27PCI: Clean-up MPS debug outputJon Mason
Clean-up MPS debug output to make it a single line and aligned, thus making it more readable for a large number of buses and devices in a single system. Suggested by Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jon Mason <mason@myri.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-27pci: Clamp pcie_set_readrq() when using "performance" settingsBenjamin Herrenschmidt
When configuring the PCIe settings for "performance", we allow parents to have a larger Max Payload Size than children and rely on children Max Read Request Size to not be larger than their own MPS to avoid having the host bridge generate responses they can't cope with. However, various drivers in Linux call pci_set_readrq() with arbitrary values, assuming this to be a simple performance tweak. This breaks under our "performance" configuration. Fix that by making sure the value programmed by pcie_set_readrq() is never larger than the configured MPS for that device. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jon Mason <mason@myri.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-27PCI: enable MPS "performance" setting to properly handle bridge MPSJon Mason
Rework the "performance" MPS option to configure the device MPS with the smaller of the device MPSS or the bridge MPS (which is assumed to be properly configured at this point to the largest allowable MPS based on its parent bus). Also, rework the MRRS setting to report an inability to set the MRRS to a valid setting. Signed-off-by: Jon Mason <mason@myri.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-27PCI: Workaround for Intel MPS errataJon Mason
Intel 5000 and 5100 series memory controllers have a known issue if read completion coalescing is enabled and the PCI-E Maximum Payload Size is set to 256B. To work around this issue, disable read completion coalescing in the memory controller and root complexes. Unfortunately, it must always be disabled, even if no 256B MPS devices are present, due to the possibility of one being hotplugged. Links to erratas: http://www.intel.com/content/dam/doc/specification-update/5000-chipset-memory-controller-hub-specification-update.pdf http://www.intel.com/content/dam/doc/specification-update/5100-memory-controller-hub-chipset-specification-update.pdf Thanks to Jesse Brandeburg and Ben Hutchings for providing insight into the problem. Tested-and-Reported-by: Avi Kivity <avi@redhat.com> Signed-off-by: Jon Mason <mason@myri.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-26Merge branch 'core-iommu-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip * 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86, ioapic: Consolidate the explicit EOI code x86, ioapic: Restore the mask bit correctly in eoi_ioapic_irq() x86, kdump, ioapic: Reset remote-IRR in clear_IO_APIC iommu: Rename the DMAR and INTR_REMAP config options x86, ioapic: Define irq_remap_modify_chip_defaults() x86, msi, intr-remap: Use the ioapic set affinity routine iommu: Cleanup ifdefs in detect_intel_iommu() iommu: No need to set dmar_disabled in check_zero_address() iommu: Move IOMMU specific code to intel-iommu.c intr_remap: Call dmar_dev_scope_init() explicitly x86, x2apic: Enable the bios request for x2apic optout
2011-10-25Merge branches 'stable/drivers-3.2', 'stable/drivers.bugfixes-3.2' and ↵Linus Torvalds
'stable/pci.fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen * 'stable/drivers-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xenbus: don't rely on xen_initial_domain to detect local xenstore xenbus: Fix loopback event channel assuming domain 0 xen/pv-on-hvm:kexec: Fix implicit declaration of function 'xen_hvm_domain' xen/pv-on-hvm kexec: add xs_reset_watches to shutdown watches from old kernel xen/pv-on-hvm kexec: update xs_wire.h:xsd_sockmsg_type from xen-unstable xen/pv-on-hvm kexec+kdump: reset PV devices in kexec or crash kernel xen/pv-on-hvm kexec: rebind virqs to existing eventchannel ports xen/pv-on-hvm kexec: prevent crash in xenwatch_thread() when stale watch events arrive * 'stable/drivers.bugfixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xen/pciback: Check if the device is found instead of blindly assuming so. xen/pciback: Do not dereference psdev during printk when it is NULL. xen: remove XEN_PLATFORM_PCI config option xen: XEN_PVHVM depends on PCI xen/pciback: double lock typo xen/pciback: use mutex rather than spinlock in vpci backend xen/pciback: Use mutexes when working with Xenbus state transitions. xen/pciback: miscellaneous adjustments xen/pciback: use mutex rather than spinlock in passthrough backend xen/pciback: use resource_size() * 'stable/pci.fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xen/pci: support multi-segment systems xen-swiotlb: When doing coherent alloc/dealloc check before swizzling the MFNs. xen/pci: make bus notifier handler return sane values xen-swiotlb: fix printk and panic args xen-swiotlb: Fix wrong panic. xen-swiotlb: Retry up three times to allocate Xen-SWIOTLB xen-pcifront: Update warning comment to use 'e820_host' option.
2011-10-14PCI: Add support for PASID capabilityJoerg Roedel
Devices supporting Process Address Space Identifiers (PASIDs) can use an IOMMU to access multiple IO address spaces at the same time. A PCIe device indicates support for this feature by implementing the PASID capability. This patch adds support for the capability to the Linux kernel. Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-14PCI: Add implementation for PRI capabilityJoerg Roedel
Implement the necessary functions to handle PRI capabilities on PCIe devices. With PRI devices behind an IOMMU can signal page fault conditions to software and recover from such faults. Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-14PCI: Export ATS functions to modulesJoerg Roedel
This patch makes the ATS functions usable for modules. They will be used by a module implementing some advanced AMD IOMMU features. Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-14PCI: Move ATS implementation into own fileJoerg Roedel
ATS does not depend on IOV support, so move the code into its own file. This file will also include support for the PRI and PASID capabilities later. Also give ATS its own Kconfig variable to allow selecting it without IOV support. Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-14PCI / PM: Remove unnecessary error variable from acpi_dev_run_wake()Rafael J. Wysocki
The result returned by acpi_dev_run_wake() is always either -EINVAL or -ENODEV, while obviously it should return 0 on success. The problem is that the leftover error variable, that's not really used in the function, is initialized with -ENODEV and then returned without modification. To fix this issue remove the error variable from acpi_dev_run_wake() and make the function return 0 on success as appropriate. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-14PCI hotplug: acpiphp: Prevent deadlock on PCI-to-PCI bridge removePrarit Bhargava
I originally submitted a patch to workaround this by pushing all Ejection Requests and Device Checks onto the kacpi_hotplug queue. http://marc.info/?l=linux-acpi&m=131678270930105&w=2 The patch is still insufficient in that Bus Checks also need to be added. Rather than add all events, including non-PCI-hotplug events, to the hotplug queue, mjg suggested that a better approach would be to modify the acpiphp driver so only acpiphp events would be added to the kacpi_hotplug queue. It's a longer patch, but at least we maintain the benefit of having separate queues in ACPI. This, of course, is still only a workaround the problem. As Bjorn and mjg pointed out, we have to refactor a lot of this code to do the right thing but at this point it is a better to have this code working. The acpi core places all events on the kacpi_notify queue. When the acpiphp driver is loaded and a PCI card with a PCI-to-PCI bridge is removed the following call sequence occurs: cleanup_p2p_bridge() -> cleanup_bridge() -> acpi_remove_notify_handler() -> acpi_os_wait_events_complete() -> flush_workqueue(kacpi_notify_wq) which is the queue we are currently executing on and the process will hang. Move all hotplug acpiphp events onto the kacpi_hotplug workqueue. In handle_hotplug_event_bridge() and handle_hotplug_event_func() we can simply push the rest of the work onto the kacpi_hotplug queue and then avoid the deadlock. Signed-off-by: Prarit Bhargava <prarit@redhat.com> Cc: mjg@redhat.com Cc: bhelgaas@google.com Cc: linux-acpi@vger.kernel.org Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-14PCI / PM: Extend PME polling to all PCI devicesRafael J. Wysocki
The land of PCI power management is a land of sorrow and ugliness, especially in the area of signaling events by devices. There are devices that set their PME Status bits, but don't really bother to send a PME message or assert PME#. There are hardware vendors who don't connect PME# lines to the system core logic (they know who they are). There are PCI Express Root Ports that don't bother to trigger interrupts when they receive PME messages from the devices below. There are ACPI BIOSes that forget to provide _PRW methods for devices capable of signaling wakeup. Finally, there are BIOSes that do provide _PRW methods for such devices, but then don't bother to call Notify() for those devices from the corresponding _Lxx/_Exx GPE-handling methods. In all of these cases the kernel doesn't have a chance to receive a proper notification that it should wake up a device, so devices stay in low-power states forever. Worse yet, in some cases they continuously send PME Messages that are silently ignored, because the kernel simply doesn't know that it should clear the device's PME Status bit. This problem was first observed for "parallel" (non-Express) PCI devices on add-on cards and Matthew Garrett addressed it by adding code that polls PME Status bits of such devices, if they are enabled to signal PME, to the kernel. Recently, however, it has turned out that PCI Express devices are also affected by this issue and that it is not limited to add-on devices, so it seems necessary to extend the PME polling to all PCI devices, including PCI Express and planar ones. Still, it would be wasteful to poll the PME Status bits of devices that are known to receive proper PME notifications, so make the kernel (1) poll the PME Status bits of all PCI and PCIe devices enabled to signal PME and (2) disable the PME Status polling for devices for which correct PME notifications are received. Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-14PCI quirk: mmc: Always check for lower base frequency quirk for Ricoh 1180:e823Josh Boyer
Commit 15bed0f2f added a quirk for the e823 Ricoh card reader to lower the base frequency. However, the quirk first checks to see if the proprietary MMC controller is disabled, and returns if so. On some devices, such as the Lenovo X220, the MMC controller is already disabled by firmware it seems, but the frequency change is still needed so sdhci-pci can talk to the cards. Since the MMC controller is disabled, the frequency fixup was never being run on these machines. This moves the e823 check above the MMC controller check so that it always gets run. This fixes https://bugzilla.redhat.com/show_bug.cgi?id=722509 Signed-off-by: Josh Boyer <jwboyer@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-14PCI: Make pci_setup_bridge() non-static for use by arch codeBenjamin Herrenschmidt
The "powernv" platform of the powerpc architecture needs to assign PCI resources using a specific algorithm to fit some HW constraints of the IBM "IODA" architecture (related to the ability to create error handling domains that encompass specific segments of MMIO space). For doing so, it wants to call pci_setup_bridge() from architecture specific resource management in order to configure bridges after all resources have been assigned. So make it non-static. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-14PCI: Add quirk for known incorrect MPSSBen Hutchings
Using legacy interrupts and TLPs > 256 bytes on the SFC4000 (all revisions) may cause interrupt messages to be replayed. In some systems this results in a non-recoverable MCE. Early boards using the SFC4000 set the maximum payload size supported (MPSS) to 1024 bytes and we should override that. There are probably other devices with similar issues, so give this quirk a generic name. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-04PCI: Disable MPS configuration by defaultJon Mason
Add the ability to disable PCI-E MPS turning and using the BIOS configured MPS defaults. Due to the number of issues recently discovered on some x86 chipsets, make this the default behavior. Also, add the option for peer to peer DMA MPS configuration. Peer to peer DMA is outside the scope of this patch, but MPS configuration could prevent it from working by having the MPS on one root port different than the MPS on another. To work around this, simply make the system wide MPS the smallest possible value (128B). Signed-off-by: Jon Mason <mason@myri.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-21iommu: Rename the DMAR and INTR_REMAP config optionsSuresh Siddha
Change the CONFIG_DMAR to CONFIG_INTEL_IOMMU to be consistent with the other IOMMU options. Rename the CONFIG_INTR_REMAP to CONFIG_IRQ_REMAP to match the irq subsystem name. And define the CONFIG_DMAR_TABLE for the common ACPI DMAR routines shared by both CONFIG_INTEL_IOMMU and CONFIG_IRQ_REMAP. Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Cc: yinghai@kernel.org Cc: youquan.song@intel.com Cc: joerg.roedel@amd.com Cc: tony.luck@intel.com Cc: dwmw2@infradead.org Link: http://lkml.kernel.org/r/20110824001456.558630224@sbsiddha-desk.sc.intel.com Signed-off-by: Ingo Molnar <mingo@elte.hu>
2011-09-13pci: Don't crash when reading mpss from root complexBenjamin Herrenschmidt
In pcie_find_smpss(), we have the following statement: if (dev->is_hotplug_bridge && (!list_is_singular(&dev->bus->devices) || dev->bus->self->pcie_type != PCI_EXP_TYPE_ROOT_PORT)) The problem is that at least on my machine, this gets called for the root complex (virtual P2P bridge), and dev->bus->self is NULL since the parent bus for this is not itself anchor to a PCI device. This adds the necessary NULL check. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jon Mason <mason@myri.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-09PCI: Remove MRRS modification from MPS setting codeJon Mason
Modifying the Maximum Read Request Size to 0 (value of 128Bytes) has massive negative ramifications on some devices. Without knowing which devices have this issue, do not modify from the default value when walking the PCI-E bus in pcie_bus_safe mode. Also, make pcie_bus_safe the default procedure. Tested-by: Sven Schnelle <svens@stackframe.org> Tested-by: Simon Kirby <sim@hostway.ca> Tested-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com> Reported-and-tested-by: Niels Ole Salscheider <niels_ole@salscheider-online.de> References: https://bugzilla.kernel.org/show_bug.cgi?id=42162 Signed-off-by: Jon Mason <mason@myri.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-09Fix pointer dereference before call to pcie_bus_configure_settingsShyam Iyer
Commit b03e7495a862 ("PCI: Set PCI-E Max Payload Size on fabric") introduced a potential NULL pointer dereference in calls to pcie_bus_configure_settings due to attempts to access pci_bus self variables when the self pointer is NULL. To correct this, verify that the self pointer in pci_bus is non-NULL before dereferencing it. Reported-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Shyam Iyer <shyam_iyer@dell.com> Signed-off-by: Jon Mason <mason@myri.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-08-26xen-pcifront: Update warning comment to use 'e820_host' option.Konrad Rzeszutek Wilk
With Xen changeset 23428 "libxl: Add 'e820_host' option to config file" the E820 as seen from the host can now be passed into the guest. This means that a PV guest can now: - Use the correct PCI I/O gap. Before these patches, Linux guest would boot up and would tell: [ 0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:c0000000) while in actuality the PCI I/O gap should have been: [ 0.000000] Allocating PCI resources starting at b0000000 (gap: b0000000:4c000000) - The PV domain with PCI devices was limited to 3GB. It now can be booted with 4GB, 8GB, or whatever number you want. The PCI devices will now _not_ conflict with System RAM. Meaning the drivers can load. CC: Jesse Barnes <jbarnes@virtuousgeek.org> CC: linux-pci@vger.kernel.org CC: stable@kernel.org [v2: Made the string less broken up. Suggested by Joe Perches] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2011-08-20pci: fix new kernel-doc warning in pci.cRandy Dunlap
Fix new kernel-doc warning in pci.c: Warning(drivers/pci/pci.c:3259): No description found for parameter 'mps' Warning(drivers/pci/pci.c:3259): Excess function parameter 'rq' description in 'pcie_set_mps' Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-08-19Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: PCI: OF: Don't crash when bridge parent is NULL. PCI: export pcie_bus_configure_settings symbol PCI: code and comments cleanup PCI: make cardbus-bridge resources optional PCI: make SRIOV resources optional PCI : ability to relocate assigned pci-resources PCI: honor child buses add_size in hot plug configuration PCI: Set PCI-E Max Payload Size on fabric
2011-08-19PCI: OF: Don't crash when bridge parent is NULL.David Daney
In pcibios_get_phb_of_node(), we will crash while booting if bus->bridge->parent is NULL. Check for this case and avoid dereferencing the NULL pointer. Signed-off-by: David Daney <david.daney@cavium.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-08-02Merge branch 'release' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (28 commits) ACPI: delete stale reference in kernel-parameters.txt ACPI: add missing _OSI strings ACPI: remove NID_INVAL thermal: make THERMAL_HWMON implementation fully internal thermal: split hwmon lookup to a separate function thermal: hide CONFIG_THERMAL_HWMON ACPI print OSI(Linux) warning only once ACPI: DMI workaround for Asus A8N-SLI Premium and Asus A8N-SLI DELUX ACPI / Battery: propagate sysfs error in acpi_battery_add() ACPI / Battery: avoid acpi_battery_add() use-after-free ACPI: introduce "acpi_rsdp=" parameter for kdump ACPI: constify ops structs ACPI: fix CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS ACPI: fix 80 char overflow ACPI / Battery: Resolve the race condition in the sysfs_remove_battery() ACPI / Battery: Add the check before refresh sysfs in the battery_notify() ACPI / Battery: Add the hibernation process in the battery_notify() ACPI / Battery: Rename acpi_battery_quirks2 with acpi_battery_quirks ACPI / Battery: Change 16-bit signed negative battery current into correct value ACPI / Battery: Add the power unit macro ...
2011-08-02PCI: export pcie_bus_configure_settings symbolJon Mason
pcie_bus_configure_settings needs to be exported if the PCI hotplug driver is being compiled as a module. Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Jon Mason <mason@myri.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-08-01PCI: code and comments cleanupRam Pai
a) adjust_resource_sorted() is now called reassign_resource_sorted() b) nice-to-have is now called optional c) add_list is now called realloc_list. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-08-01PCI: make cardbus-bridge resources optionalRam Pai
Allocate resources to cardbus bridge only after all other genuine resources requests are satisfied. Dont retry if resource allocation for cardbus-bridges fail. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-08-01PCI: make SRIOV resources optionalYinghai Lu
From: Yinghai Lu <yinghai@kernel.org> Allocate resources to SRIOV BARs only after all other required resource-requests are satisfied. Dont retry if resource allocation for SRIOV BARs fail. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-08-01PCI : ability to relocate assigned pci-resourcesRam Pai
Currently pci-bridges are allocated enough resources to satisfy their immediate requirements. Any additional resource-requests fail if additional free space, contiguous to the one already allocated, is not available. This behavior is not reasonable since sufficient contiguous resources, that can satisfy the request, are available at a different location. This patch provides the ability to expand and relocate a allocated resource. v2: Changelog: Fixed size calculation in pci_reassign_resource() v3: Changelog : Split this patch. The resource.c changes are already upstream. All the pci driver changes are in here. Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-08-01PCI: honor child buses add_size in hot plug configurationYinghai Lu
git commit c8adf9a3e873eddaaec11ac410a99ef6b9656938 "PCI: pre-allocate additional resources to devices only after successful allocation of essential resources." fails to take into consideration the optional-resources needed by children devices while calculating the optional-resource needed by the bridge. This can be a problem on some setup. For example, if a hotplug bridge has 8 children hotplug bridges, the bridge should have enough resources to accomodate the hotplug requirements for each of its children hotplug bridges. Currently this is not the case. This patch fixes the problem. Signed-off-by: Yinghai Lu <yinghai@kernel.org> Reviewed-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-08-01PCI: Set PCI-E Max Payload Size on fabricJon Mason
On a given PCI-E fabric, each device, bridge, and root port can have a different PCI-E maximum payload size. There is a sizable performance boost for having the largest possible maximum payload size on each PCI-E device. However, if improperly configured, fatal bus errors can occur. Thus, it is important to ensure that PCI-E payloads sends by a device are never larger than the MPS setting of all devices on the way to the destination. This can be achieved two ways: - A conservative approach is to use the smallest common denominator of the entire tree below a root complex for every device on that fabric. This means for example that having a 128 bytes MPS USB controller on one leg of a switch will dramatically reduce performances of a video card or 10GE adapter on another leg of that same switch. It also means that any hierarchy supporting hotplug slots (including expresscard or thunderbolt I suppose, dbl check that) will have to be entirely clamped to 128 bytes since we cannot predict what will be plugged into those slots, and we cannot change the MPS on a "live" system. - A more optimal way is possible, if it falls within a couple of constraints: * The top-level host bridge will never generate packets larger than the smallest TLP (or if it can be controlled independently from its MPS at least) * The device will never generate packets larger than MPS (which can be configured via MRRS) * No support of direct PCI-E <-> PCI-E transfers between devices without some additional code to specifically deal with that case Then we can use an approach that basically ignores downstream requests and focuses exclusively on upstream requests. In that case, all we need to care about is that a device MPS is no larger than its parent MPS, which allows us to keep all switches/bridges to the max MPS supported by their parent and eventually the PHB. In this case, your USB controller would no longer "starve" your 10GE Ethernet and your hotplug slots won't affect your global MPS. Additionally, the hotplugged devices themselves can be configured to a larger MPS up to the value configured in the hotplug bridge. To choose between the two available options, two PCI kernel boot args have been added to the PCI calls. "pcie_bus_safe" will provide the former behavior, while "pcie_bus_perf" will perform the latter behavior. By default, the latter behavior is used. NOTE: due to the location of the enablement, each arch will need to add calls to this function. This patch only enables x86. This patch includes a number of changes recommended by Benjamin Herrenschmidt. Tested-by: Jordan_Hargrave@dell.com Signed-off-by: Jon Mason <mason@myri.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-29Merge branch 'linux-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6 * 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: PCI: remove printks about disabled bridge windows PCI: fold pci_calc_resource_flags() into decode_bar() PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR PCI: correct pcie_set_readrq write size PCI: pciehp: change wait time for valid configuration access x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems PCI: ARI is a PCIe v2 feature x86/PCI: quirks: Use pci_dev->revision PCI: Make the struct pci_dev * argument of pci_fixup_irqs const. PCI hotplug: cpqphp: use pci_dev->vendor PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device} x86/PCI: config space accessor functions should not ignore the segment argument PCI: Assign values to 'pci_obff_signal_type' enumeration constants x86/PCI: reduce severity of host bridge window conflict warnings PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI PCI: PCIe AER: add aer_recover_queue x86/PCI: select direct access mode for mmconfig option PCI hotplug: Rename is_ejectable which also exists in dock.c
2011-07-26Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: merge fchmod() and fchmodat() guts, kill ancient broken kludge xfs: fix misspelled S_IS...() xfs: get rid of open-coded S_ISREG(), etc. vfs: document locking requirements for d_move, __d_move and d_materialise_unique omfs: fix (mode & S_IFDIR) abuse btrfs: S_ISREG(mode) is not mode & S_IFREG... ima: fmode_t misspelled as mode_t... pci-label.c: size_t misspelled as mode_t jffs2: S_ISLNK(mode & S_IFMT) is pointless snd_msnd ->mode is fmode_t, not mode_t v9fs_iop_get_acl: get rid of unused variable vfs: dont chain pipe/anon/socket on superblock s_inodes list Documentation: Exporting: update description of d_splice_alias fs: add missing unlock in default_llseek()
2011-07-26atomic: use <linux/atomic.h>Arun Sharma
This allows us to move duplicated code in <asm/atomic.h> (atomic_inc_not_zero() for now) to <linux/atomic.h> Signed-off-by: Arun Sharma <asharma@fb.com> Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: David Miller <davem@davemloft.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-26pci-label.c: size_t misspelled as mode_tAl Viro
no, really, strlen() and snprintf() do not return mode_t values... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>