| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Print IRQ number used by PCIe Link Bandwidth Notification (Dongdong
Liu)
- Add schedule point in pci_read_config() to reduce max latency
(Jiang Biao)
- Add Kconfig options for MPS/MRRS strategy (Jim Quinlan)
Resource management:
- Fix pci_iounmap() memory leak when !CONFIG_GENERIC_IOMAP (Lorenzo
Pieralisi)
PCIe native device hotplug:
- Reduce noisiness on hot removal (Lukas Wunner)
Power management:
- Revert "PCI/PM: Apply D2 delay as milliseconds, not microseconds"
that was done on the basis of spec typo (Bjorn Helgaas)
- Rename pci_dev.d3_delay to d3hot_delay to remove D3hot/D3cold
ambiguity (Krzysztof Wilczyński)
- Remove unused pcibios_pm_ops (Vaibhav Gupta)
IOMMU:
- Enable Translation Blocking for external devices to harden against
DMA attacks (Rajat Jain)
Error handling:
- Add an ACPI APEI notifier chain for vendor CPER records to enable
device-specific error handling (Shiju Jose)
ASPM:
- Remove struct aspm_register_info to simplify code (Saheed O.
Bolarinwa)
Amlogic Meson PCIe controller driver:
- Build as module by default (Kevin Hilman)
Ampere Altra PCIe controller driver:
- Add MCFG quirk to work around non-standard ECAM implementation
(Tuan Phan)
Broadcom iProc PCIe controller driver:
- Set affinity mask on MSI interrupts (Mark Tomlinson)
Broadcom STB PCIe controller driver:
- Make PCIE_BRCMSTB depend on ARCH_BRCMSTB (Jim Quinlan)
- Add DT bindings for more Brcmstb chips (Jim Quinlan)
- Add bcm7278 register info (Jim Quinlan)
- Add bcm7278 PERST# support (Jim Quinlan)
- Add suspend and resume pm_ops (Jim Quinlan)
- Add control of rescal reset (Jim Quinlan)
- Set additional internal memory DMA viewport sizes (Jim Quinlan)
- Accommodate MSI for older chips (Jim Quinlan)
- Set bus max burst size by chip type (Jim Quinlan)
- Add support for bcm7211, bcm7216, bcm7445, bcm7278 (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Use dev_err_probe() to reduce redundant messages (Anson Huang)
Freescale Layerscape PCIe controller driver:
- Enforce 4K DMA buffer alignment in endpoint test (Hou Zhiqiang)
- Add DT compatible strings for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint support for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint test support for lS1088a (Xiaowei Bao)
- Add MSI-X support for ls1088a (Xiaowei Bao)
HiSilicon HIP PCIe controller driver:
- Handle HIP-specific errors via ACPI APEI (Yicong Yang)
HiSilicon Kirin PCIe controller driver:
- Return -EPROBE_DEFER if the GPIO isn't ready (Bean Huo)
Intel VMD host bridge driver:
- Factor out physical offset, bus offset, IRQ domain, IRQ allocation
(Jon Derrick)
- Use generic PCI PM correctly (Jon Derrick)
Marvell Aardvark PCIe controller driver:
- Fix compilation on s390 (Pali Rohár)
- Implement driver 'remove' function and allow to build it as module
(Pali Rohár)
- Move PCIe reset card code to advk_pcie_train_link() (Pali Rohár)
- Convert mvebu a3700 internal SMCC firmware return codes to errno
(Pali Rohár)
- Fix initialization with old Marvell's Arm Trusted Firmware (Pali
Rohár)
Microsoft Hyper-V host bridge driver:
- Fix hibernation in case interrupts are not re-created (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Stop checking return value of debugfs_create() functions (Greg
Kroah-Hartman)
- Convert to use DEFINE_SEQ_ATTRIBUTE macro (Liu Shixin)
Qualcomm PCIe controller driver:
- Reset PCIe to work around Qsdk U-Boot issue (Ansuel Smith)
Renesas R-Car PCIe controller driver:
- Add DT documentation for r8a774a1, r8a774b1, r8a774e1 endpoints
(Lad Prabhakar)
- Add RZ/G2M, RZ/G2N, RZ/G2H IDs to endpoint test (Lad Prabhakar)
- Add DT support for r8a7742 (Lad Prabhakar)
Socionext UniPhier Pro5 controller driver:
- Add DT descriptions of iATU register (host and endpoint) (Kunihiko
Hayashi)
Synopsys DesignWare PCIe controller driver:
- Add link up check in dw_child_pcie_ops.map_bus() (racy, but seems
unavoidable) (Hou Zhiqiang)
- Fix endpoint Header Type check so multi-function devices work (Hou
Zhiqiang)
- Skip PCIE_MSI_INTR0* programming if MSI is disabled (Jisheng Zhang)
- Stop leaking MSI page in suspend/resume (Jisheng Zhang)
- Add common iATU register support instead of keystone-specific code
(Kunihiko Hayashi)
- Major config space access and other cleanups in dwc core and
drivers that use it (al, exynos, histb, imx6, intel-gw, keystone,
kirin, meson, qcom, tegra) (Rob Herring)
- Add multiple PFs support for endpoint (Xiaowei Bao)
- Add MSI-X doorbell mode in endpoint mode (Xiaowei Bao)
Miscellaneous:
- Use fallthrough pseudo-keyword (Gustavo A. R. Silva)
- Fix "0 used as NULL pointer" warnings (Gustavo Pimentel)
- Fix "cast truncates bits from constant value" warnings (Gustavo
Pimentel)
- Remove redundant zeroing for sg_init_table() (Julia Lawall)
- Use scnprintf(), not snprintf(), in sysfs "show" functions
(Krzysztof Wilczyński)
- Remove unused assignments (Krzysztof Wilczyński)
- Fix "0 used as NULL pointer" warning (Krzysztof Wilczyński)
- Simplify bool comparisons (Krzysztof Wilczyński)
- Use for_each_child_of_node() and for_each_node_by_name() (Qinglang
Miao)
- Simplify return expressions (Qinglang Miao)"
* tag 'pci-v5.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (147 commits)
PCI: vmd: Update VMD PM to correctly use generic PCI PM
PCI: vmd: Create IRQ allocation helper
PCI: vmd: Create IRQ Domain configuration helper
PCI: vmd: Create bus offset configuration helper
PCI: vmd: Create physical offset helper
PCI: v3-semi: Remove unneeded break
PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()
PCI/ASPM: Remove struct pcie_link_state.l1ss
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap
PCI/ASPM: Pass L1SS Capabilities value, not struct aspm_register_info
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl1
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl2 (unused)
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap_ptr
PCI/ASPM: Remove struct aspm_register_info.latency_encoding
PCI/ASPM: Remove struct aspm_register_info.enabled
PCI/ASPM: Remove struct aspm_register_info.support
PCI/ASPM: Use 'parent' and 'child' for readability
PCI/ASPM: Move LTR path check to where it's used
PCI/ASPM: Move pci_clear_and_set_dword() earlier
PCI: dwc: Fix MSI page leakage in suspend/resume
...
|
|
Most of dma-debug.h is not required by anything outside of kernel/dma.
Move the four declarations needed by dma-mappin.h or dma-ops providers
into dma-mapping.h and dma-map-ops.h, and move the remainder of the
file to kernel/dma/debug.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The "struct dev_pm_ops pcibios_pm_ops", declared in include/linux/pci.h and
defined in drivers/pci/pci-driver.c, provided arch-specific hooks when a
PCI device was doing a hibernate transition.
394216275c7d ("s390: remove broken hibernate / power management support")
removed the last use of pcibios_pm_ops, so remove it completely.
[bhelgaas: drop unused "error"]
Link: https://lore.kernel.org/r/20200730194416.1029509-1-vaibhavgupta40@gmail.com
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
pci_call_probe() prevents the nesting of work_on_cpu() for a scenario
where a VF device is probed from work_on_cpu() of the PF.
Replace the cpumask used in pci_call_probe() from all online CPUs to only
housekeeping CPUs. This is to ensure that there are no additional latency
overheads caused due to the pinning of jobs on isolated CPUs.
Signed-off-by: Alex Belits <abelits@marvell.com>
Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lkml.kernel.org/r/20200625223443.2684-3-nitesh@redhat.com
|
|
Because all callers of dev_pm_smart_suspend_and_suspended use it only
for checking whether or not to skip driver suspend callbacks for a
device, rename it to dev_pm_skip_suspend() in analogy with
dev_pm_skip_resume().
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The name of dev_pm_may_skip_resume() may be easily confused with the
power.may_skip_resume flag which is not checked by that function, so
rename the former as dev_pm_skip_resume().
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Because the power.may_skip_resume device status bit is taken
into account in combination with the DPM_FLAG_LEAVE_SUSPENDED
driver flag, it can be set to 'true' for all devices in the
"suspend" phase of a suspend-resume cycle, so do that.
Then, neither the PM core nor the middle-layer (sybsystem) code
handling it needs to set it to 'true' any more and it just has
to be cleared if there is a reason to avoid skipping the "noirq"
and "early" resume callbacks provided by the driver, so update
the code in question accordingly.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The current code in device_resume_noirq() causes the entire early
resume and resume phases of device suspend to be skipped for
devices for which the noirq resume phase have been skipped (due
to the LEAVE_SUSPENDED flag being set) on the premise that those
devices should stay in runtime-suspend after system-wide resume.
However, that may not be correct in two situations. First, the
middle layer (subsystem) noirq resume callback may be missing for
a given device, but its early resume callback may be present and it
may need to do something even if it decides to skip the driver
callback. Second, if the device's wakeup settings were adjusted
in the suspend phase without resuming the device (that was in
runtime suspend at that time), they most likely need to be
adjusted again in the resume phase and so the driver callback
in that phase needs to be run.
For the above reason, modify the core to allow the middle layer
->resume_late callback to run even if its ->resume_noirq callback
is missing (and the core has skipped the driver-level callback
in that phase) and to allow all device callbacks to run in the
resume phase. Also make the core set the PM-runtime status of
devices with SMART_SUSPEND set whose resume callbacks are not
skipped to "active" in the "noirq" resume phase and update the
affected subsystems (PCI and ACPI) accordingly.
After this change, middle-layer (subsystem) callbacks will always
be invoked in all phases of system suspend and resume and driver
callbacks will always run in the prepare, suspend, resume, and
complete phases for all devices.
For devices with SMART_SUSPEND set, driver callbacks will be
skipped in the late and noirq phases of system suspend if those
devices remain in runtime suspend in __device_suspend_late().
Driver callbacks will also be skipped for them during the
noirq and early phases of the "thaw" transition related to
hibernation in that case.
Setting LEAVE_SUSPENDED means that the driver allows its callbacks
to be skipped in the noirq and early phases of system resume, but
some additional conditions need to be met for that to happen (among
other things, the power.may_skip_resume flag needs to be set for the
device during system suspend for the driver callbacks to be skipped
during the subsequent resume transition).
For all devices with SMART_SUSPEND set whose driver callbacks are
invoked during system resume, the PM-runtime status will be set to
"active" (by the core).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Currently Linux does not follow PCIe spec regarding the required delays
after reset. A concrete example is a Thunderbolt add-in-card that consists
of a PCIe switch and two PCIe endpoints:
+-1b.0-[01-6b]----00.0-[02-6b]--+-00.0-[03]----00.0 TBT controller
+-01.0-[04-36]-- DS hotplug port
+-02.0-[37]----00.0 xHCI controller
\-04.0-[38-6b]-- DS hotplug port
The root port (1b.0) and the PCIe switch downstream ports are all PCIe Gen3
so they support 8GT/s link speeds.
We wait for the PCIe hierarchy to enter D3cold (runtime):
pcieport 0000:00:1b.0: power state changed by ACPI to D3cold
When it wakes up from D3cold, according to the PCIe 5.0 section 5.8 the
PCIe switch is put to reset and its power is re-applied. This means that we
must follow the rules in PCIe 5.0 section 6.6.1.
For the PCIe Gen3 ports we are dealing with here, the following applies:
With a Downstream Port that supports Link speeds greater than 5.0 GT/s,
software must wait a minimum of 100 ms after Link training completes
before sending a Configuration Request to the device immediately below
that Port. Software can determine when Link training completes by polling
the Data Link Layer Link Active bit or by setting up an associated
interrupt (see Section 6.7.3.3).
Translating this into the above topology we would need to do this (DLLLA
stands for Data Link Layer Link Active):
0000:00:1b.0: wait for 100 ms after DLLLA is set before access to 0000:01:00.0
0000:02:00.0: wait for 100 ms after DLLLA is set before access to 0000:03:00.0
0000:02:02.0: wait for 100 ms after DLLLA is set before access to 0000:37:00.0
I've instrumented the kernel with some additional logging so we can see the
actual delays performed:
pcieport 0000:00:1b.0: power state changed by ACPI to D0
pcieport 0000:00:1b.0: waiting for D3cold delay of 100 ms
pcieport 0000:00:1b.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:01.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:04.0: waiting for D3hot delay of 10 ms
For the switch upstream port (01:00.0 reachable through 00:1b.0 root port)
we wait for 100 ms but not taking into account the DLLLA requirement. We
then wait 10 ms for D3hot -> D0 transition of the root port and the two
downstream hotplug ports. This means that we deviate from what the spec
requires.
Performing the same check for system sleep (s2idle) transitions it turns
out to be even worse. None of the mandatory delays are performed. If this
would be S3 instead of s2idle then according to PCI FW spec 3.2 section
4.6.8. there is a specific _DSM that allows the OS to skip the delays but
this platform does not provide the _DSM and does not go to S3 anyway so no
firmware is involved that could already handle these delays.
On this particular platform these delays are not actually needed because
there is an additional delay as part of the ACPI power resource that is
used to turn on power to the hierarchy but since that additional delay is
not required by any of standards (PCIe, ACPI) it is not present in the
Intel Ice Lake, for example where missing the mandatory delays causes
pciehp to start tearing down the stack too early (links are not yet
trained). Below is an example how it looks like when this happens:
pcieport 0000:83:04.0: pciehp: Slot(4): Card not present
pcieport 0000:87:04.0: PME# disabled
pcieport 0000:83:04.0: pciehp: pciehp_unconfigure_device: domain:bus:dev = 0000:86:00
pcieport 0000:86:00.0: Refused to change power state, currently in D3
pcieport 0000:86:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x201ff)
pcieport 0000:86:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
There is also one reported case (see the bugzilla link below) where the
missing delay causes xHCI on a Titan Ridge controller fail to runtime
resume when USB-C dock is plugged. This does not involve pciehp but instead
the PCI core fails to runtime resume the xHCI device:
pcieport 0000:04:02.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:04:02.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100406)
xhci_hcd 0000:39:00.0: Refused to change power state, currently in D3
xhci_hcd 0000:39:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x1ff)
xhci_hcd 0000:39:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
Add a new function pci_bridge_wait_for_secondary_bus() that is called on
PCI core resume and runtime resume paths accordingly if the bridge entered
D3cold (and thus went through reset).
This is second attempt to add the missing delays. The previous solution in
c2bf1fc212f7 ("PCI: Add missing link delays required by the PCIe spec") was
reverted because of two issues it caused:
1. One system become unresponsive after S3 resume due to PME service
spinning in pcie_pme_work_fn(). The root port in question reports that
the xHCI sent PME but the xHCI device itself does not have PME status
set. The PME status bit is never cleared in the root port resulting
the indefinite loop in pcie_pme_work_fn().
2. Slows down resume if the root/downstream port does not support Data
Link Layer Active Reporting because pcie_wait_for_link_delay() waits
1100 ms in that case.
This version should avoid the above issues because we restrict the delay to
happen only if the port went into D3cold.
Link: https://lore.kernel.org/linux-pci/SL2P216MB01878BBCD75F21D882AEEA2880C60@SL2P216MB0187.KORP216.PROD.OUTLOOK.COM/
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203885
Link: https://lore.kernel.org/r/20191112091617.70282-3-mika.westerberg@linux.intel.com
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Move the invocation of pci_update_current_state() from pci_power_up() to
pci_pm_default_resume_early(), which is the only caller of that function.
Preparatory change, no functional impact.
Link: https://lore.kernel.org/r/37482337.udjOGdOKNb@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The struct pci_driver.suspend_late() hook is one of the legacy PCI power
management callbacks, and there are no remaining users of it. Remove it.
Link: https://lore.kernel.org/r/20191101204558.210235-7-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The struct pci_driver.resume_early() hook is one of the legacy PCI power
management callbacks, and there are no remaining users of it. Remove it.
Link: https://lore.kernel.org/r/20191101204558.210235-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add and use pci_WARN() wrappers so warnings include device information.
Link: https://lore.kernel.org/r/20191017212851.54237-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use the PCI dev_printk() wrappers for consistency with the rest of the PCI
core. No functional change intended.
Link: https://lore.kernel.org/r/20191017212851.54237-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some of the power management ops use this style:
struct device_driver *drv = dev->driver;
if (drv && drv->pm && drv->pm->prepare(dev))
drv->pm->prepare(dev);
while others use this:
const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
if (pm && pm->runtime_resume)
pm->runtime_resume(dev);
Convert the first style to the second so they're all consistent. Remove
local "error" variables when unnecessary. No functional change intended.
Link: https://lore.kernel.org/r/20191014230016.240912-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
pci_pm_resume() and pci_pm_restore() call pci_pm_default_resume(), which
runs resume fixups before disabling wakeup events:
static void pci_pm_default_resume(struct pci_dev *pci_dev)
{
pci_fixup_device(pci_fixup_resume, pci_dev);
pci_enable_wake(pci_dev, PCI_D0, false);
}
pci_pm_runtime_resume() does both of these, but in the opposite order:
pci_enable_wake(pci_dev, PCI_D0, false);
pci_fixup_device(pci_fixup_resume, pci_dev);
We should always use the same ordering unless there's a reason to do
otherwise. Change pci_pm_runtime_resume() to call pci_pm_default_resume()
instead of open-coding this, so the fixups are always done before disabling
wakeup events.
pci_pm_default_resume() is called from pci_pm_runtime_resume(), which is
under #ifdef CONFIG_PM. If SUSPEND and HIBERNATION are disabled, PM_SLEEP
is disabled also, so move pci_pm_default_resume() from #ifdef
CONFIG_PM_SLEEP to #ifdef CONFIG_PM.
Link: https://lore.kernel.org/r/20191014230016.240912-5-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Previously, pci_pm_resume_noirq() cleared the PME Status bit in the Root
Status register only if the device had no driver or the driver did not
implement legacy power management. It should clear PME Status regardless
of what sort of power management the driver supports, so do this before
checking for legacy power management.
This affects Root Ports and Root Complex Event Collectors, for which the
usual driver is the PCIe portdrv, which implements new power management, so
this change is just on principle, not to fix any actual defects.
Fixes: a39bd851dccf ("PCI/PM: Clear PCIe PME Status bit in core, not PCIe port driver")
Link: https://lore.kernel.org/r/20191014230016.240912-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
pci_pm_thaw_noirq() is supposed to return the device to D0 and restore its
configuration registers, but previously it only did that for devices whose
drivers implemented the new power management ops.
Hibernation, e.g., via "echo disk > /sys/power/state", involves freezing
devices, creating a hibernation image, thawing devices, writing the image,
and powering off. The fact that thawing did not return devices with legacy
power management to D0 caused errors, e.g., in this path:
pci_pm_thaw_noirq
if (pci_has_legacy_pm_support(pci_dev)) # true for Mellanox VF driver
return pci_legacy_resume_early(dev) # ... legacy PM skips the rest
pci_set_power_state(pci_dev, PCI_D0)
pci_restore_state(pci_dev)
pci_pm_thaw
if (pci_has_legacy_pm_support(pci_dev))
pci_legacy_resume
drv->resume
mlx4_resume
...
pci_enable_msix_range
...
if (dev->current_state != PCI_D0) # <---
return -EINVAL;
which caused these warnings:
mlx4_core a6d1:00:02.0: INTx is not supported in multi-function mode, aborting
PM: dpm_run_callback(): pci_pm_thaw+0x0/0xd7 returns -95
PM: Device a6d1:00:02.0 failed to thaw: error -95
Return devices to D0 and restore config registers for all devices, not just
those whose drivers support new power management.
[bhelgaas: also call pci_restore_state() before pci_legacy_resume_early(),
update comment, add stable tag, commit log]
Link: https://lore.kernel.org/r/KU1P153MB016637CAEAD346F0AA8E3801BFAD0@KU1P153MB0166.APCP153.PROD.OUTLOOK.COM
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # v4.13+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration changes:
- Evaluate PCI Boot Configuration _DSM to learn if firmware wants us
to preserve its resource assignments (Benjamin Herrenschmidt)
- Simplify resource distribution (Nicholas Johnson)
- Decode 32 GT/s link speed (Gustavo Pimentel)
Virtualization:
- Fix incorrect caching of VF config space size (Alex Williamson)
- Fix VF driver probing sysfs knobs (Alex Williamson)
Peer-to-peer DMA:
- Fix dma_virt_ops check (Logan Gunthorpe)
Altera host bridge driver:
- Allow building as module (Ley Foon Tan)
Armada 8K host bridge driver:
- add PHYs support (Miquel Raynal)
DesignWare host bridge driver:
- Export APIs to support removable loadable module (Vidya Sagar)
- Enable Relaxed Ordering erratum workaround only on Tegra20 &
Tegra30 (Vidya Sagar)
Hyper-V host bridge driver:
- Fix use-after-free in eject (Dexuan Cui)
Mobiveil host bridge driver:
- Clean up and fix many issues, including non-identify mapped
windows, 64-bit windows, multi-MSI, class code, INTx clearing (Hou
Zhiqiang)
Qualcomm host bridge driver:
- Use clk bulk API for 2.4.0 controllers (Bjorn Andersson)
- Add QCS404 support (Bjorn Andersson)
- Assert PERST for at least 100ms (Niklas Cassel)
R-Car host bridge driver:
- Add r8a774a1 DT support (Biju Das)
Tegra host bridge driver:
- Add support for Gen2, opportunistic UpdateFC and ACK (PCIe protocol
details) AER, GPIO-based PERST# (Manikanta Maddireddy)
- Fix many issues, including power-on failure cases, interrupt
masking in suspend, UPHY settings, AFI dynamic clock gating,
pending DLL transactions (Manikanta Maddireddy)
Xilinx host bridge driver:
- Fix NWL Multi-MSI programming (Bharat Kumar Gogada)
Endpoint support:
- Fix 64bit BAR support (Alan Mikhak)
- Fix pcitest build issues (Alan Mikhak, Andy Shevchenko)
Bug fixes:
- Fix NVIDIA GPU multi-function power dependencies (Abhishek Sahu)
- Fix NVIDIA GPU HDA enablement issue (Lukas Wunner)
- Ignore lockdep for sysfs "remove" (Marek Vasut)
Misc:
- Convert docs to reST (Changbin Du, Mauro Carvalho Chehab)"
* tag 'pci-v5.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (107 commits)
PCI: Enable NVIDIA HDA controllers
tools: PCI: Fix installation when `make tools/pci_install`
PCI: dwc: pci-dra7xx: Fix compilation when !CONFIG_GPIOLIB
PCI: Fix typos and whitespace errors
PCI: mobiveil: Fix INTx interrupt clearing in mobiveil_pcie_isr()
PCI: mobiveil: Fix infinite-loop in the INTx handling function
PCI: mobiveil: Move PCIe PIO enablement out of inbound window routine
PCI: mobiveil: Add upper 32-bit PCI base address setup in inbound window
PCI: mobiveil: Add upper 32-bit CPU base address setup in outbound window
PCI: mobiveil: Mask out hardcoded bits in inbound/outbound windows setup
PCI: mobiveil: Clear the control fields before updating it
PCI: mobiveil: Add configured inbound windows counter
PCI: mobiveil: Fix the valid check for inbound and outbound windows
PCI: mobiveil: Clean-up program_{ib/ob}_windows()
PCI: mobiveil: Remove an unnecessary return value check
PCI: mobiveil: Fix error return values
PCI: mobiveil: Refactor the MEM/IO outbound window initialization
PCI: mobiveil: Make some register updates more readable
PCI: mobiveil: Reformat the code for readability
dt-bindings: PCI: mobiveil: Change gpio_slave and apb_csr to optional
...
|
|
* pm-sleep:
PM: sleep: Drop dev_pm_skip_next_resume_phases()
ACPI: PM: Drop unused function and function header
ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS
ACPI: PM: Simplify and fix PM domain hibernation callbacks
PCI: PM: Simplify bus-level hibernation callbacks
PM: ACPI/PCI: Resume all devices during hibernation
kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset()
PM: sleep: Update struct wakeup_source documentation
drivers: base: power: remove wakeup_sources_stats_dentry variable
PM: suspend: Rename pm_suspend_via_s2idle()
PM: sleep: Show how long dpm_suspend_start() and dpm_suspend_end() take
PM: hibernate: powerpc: Expose pfn_is_nosave() prototype
|
|
After a previous change causing all runtime-suspended PCI devices
to be resumed before creating a snapshot image of memory during
hibernation, it is not necessary to worry about the case in which
them might be left in runtime-suspend any more, so get rid of the
code related to that from bus-level PCI hibernation callbacks.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
|
|
Both the PCI bus type and the ACPI PM domain avoid resuming
runtime-suspended devices with DPM_FLAG_SMART_SUSPEND set during
hibernation (before creating the snapshot image of system memory),
but that turns out to be a mistake. It leads to functional issues
and adds complexity that's hard to justify.
For this reason, resume all runtime-suspended PCI devices and all
devices in the ACPI PM domains before creating a snapshot image of
system memory during hibernation.
Fixes: 05087360fd7a (ACPI / PM: Take SMART_SUSPEND driver flag into account)
Fixes: c4b65157aeef (PCI / PM: Take SMART_SUSPEND driver flag into account)
Link: https://lore.kernel.org/linux-acpi/917d4399-2e22-67b1-9d54-808561f9083f@uwyo.edu/T/#maf065fe6e4974f2a9d79f332ab99dfaba635f64c
Reported-by: Robert R. Howell <RHowell@uwyo.edu>
Tested-by: Robert R. Howell <RHowell@uwyo.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
|
|
|
|
In pci_pm_complete() there are checks to decide whether or not to
resume devices that were left in runtime-suspend during the preceding
system-wide transition into a sleep state. They involve checking the
current power state of the device and comparing it with the power
state of it set before the preceding system-wide transition, but the
platform component of the device's power state is not handled
correctly in there.
Namely, on platforms with ACPI, the device power state information
needs to be updated with care, so that the reference counters of
power resources used by the device (if any) are set to ensure that
the refreshed power state of it will be maintained going forward.
To that end, introduce a new ->refresh_state() platform PM callback
for PCI devices, for asking the platform to refresh the device power
state data and ensure that the corresponding power state will be
maintained going forward, make it invoke acpi_device_update_power()
(for devices with ACPI PM) on platforms with ACPI and make
pci_pm_complete() use it, through a new pci_refresh_power_state()
wrapper function.
Fixes: a0d2a959d3da (PCI: Avoid unnecessary resume after direct-complete)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
There are platforms that do not call pm_set_suspend_via_firmware(),
so pm_suspend_via_firmware() returns 'false' on them, but the power
states of PCI devices (PCIe ports in particular) are changed as a
result of powering down core platform components during system-wide
suspend. Thus the pm_suspend_via_firmware() checks in
pci_pm_suspend_noirq() and pci_pm_resume_noirq() introduced by
commit 3e26c5feed2a ("PCI: PM: Skip devices in D0 for suspend-to-
idle") are not sufficient to determine that devices left in D0
during suspend will remain in D0 during resume and so the bus-level
power management can be skipped for them.
For this reason, introduce a new global suspend flag,
PM_SUSPEND_FLAG_NO_PLATFORM, set it for suspend-to-idle only
and replace the pm_suspend_via_firmware() checks mentioned above
with checks against this flag.
Fixes: 3e26c5feed2a ("PCI: PM: Skip devices in D0 for suspend-to-idle")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
|
|
The code in pci_dev_keep_suspended() is relatively hard to follow due
to the negative checks in it and in its callers and the function has
a possible side-effect (disabling the PME) which doesn't really match
its role.
For this reason, move the PME disabling from pci_dev_keep_suspended()
to a separate function and change the semantics (and name) of the
rest of it, so that 'true' is returned when the device needs to be
resumed (and not the other way around). Change the callers of
pci_dev_keep_suspended() accordingly.
While at it, make the code flow in pci_pm_poweroff() reflect the
pci_pm_suspend() more closely to avoid arbitrary differences between
them.
This is a cosmetic change with no intention to alter behavior.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Commit d491f2b75237 ("PCI: PM: Avoid possible suspend-to-idle issue")
attempted to avoid a problem with devices whose drivers want them to
stay in D0 over suspend-to-idle and resume, but it did not go as far
as it should with that.
Namely, first of all, the power state of a PCI bridge with a
downstream device in D0 must be D0 (based on the PCI PM spec r1.2,
sec 6, table 6-1, if the bridge is not in D0, there can be no PCI
transactions on its secondary bus), but that is not actively enforced
during system-wide PM transitions, so use the skip_bus_pm flag
introduced by commit d491f2b75237 for that.
Second, the configuration of devices left in D0 (whatever the reason)
during suspend-to-idle need not be changed and attempting to put them
into D0 again by force is pointless, so explicitly avoid doing that.
Fixes: d491f2b75237 ("PCI: PM: Avoid possible suspend-to-idle issue")
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
|
|
Commit 0e7df22401a3 ("PCI: Add sysfs sriov_drivers_autoprobe to control
VF driver binding") introduced the sriov_drivers_autoprobe attribute
which allows users to prevent the kernel from automatically probing a
driver for new VFs as they are created. This allows VFs to be spawned
without automatically binding the new device to a host driver, such as
in cases where the user intends to use the device only with a meta
driver like vfio-pci. However, the current implementation prevents any
use of drivers_probe with the VF while sriov_drivers_autoprobe=0. This
blocks the now current general practice of setting driver_override
followed by using drivers_probe to bind a device to a specified driver.
The kernel never automatically sets a driver_override therefore it seems
we can assume a driver_override reflects the intent of the user. Also,
probing a device using a driver_override match seems outside the scope
of the 'auto' part of sriov_drivers_autoprobe. Therefore, let's allow
driver_override matches regardless of sriov_drivers_autoprobe, which we
can do by simply testing if a driver_override is set for a device as a
'can probe' condition.
Fixes: 0e7df22401a3 ("PCI: Add sysfs sriov_drivers_autoprobe to control VF driver binding")
Link: https://lore.kernel.org/lkml/155742996741.21878.569845487290798703.stgit@gimli.home
Link: https://lore.kernel.org/linux-pci/155672991496.20698.4279330795743262888.stgit@gimli.home/T/#u
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Commit 0e7df22401a3 ("PCI: Add sysfs sriov_drivers_autoprobe to control
VF driver binding") allows the user to specify that drivers for VFs of
a PF should not be probed, but it actually causes pci_device_probe() to
return success back to the driver core in this case. Therefore by all
sysfs appearances the device is bound to a driver, the driver link from
the device exists as does the device link back from the driver, yet the
driver's probe function is never called on the device. We also fail to
do any sort of cleanup when we're prohibited from probing the device,
the IRQ setup remains in place and we even hold a device reference.
Instead, abort with errno before any setup or references are taken when
pci_device_can_probe() prevents us from trying to probe the device.
Link: https://lore.kernel.org/lkml/155672991496.20698.4279330795743262888.stgit@gimli.home
Fixes: 0e7df22401a3 ("PCI: Add sysfs sriov_drivers_autoprobe to control VF driver binding")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
If a PCI driver leaves the device handled by it in D0 and calls
pci_save_state() on the device in its ->suspend() or ->suspend_late()
callback, it can expect the device to stay in D0 over the whole
s2idle cycle. However, that may not be the case if there is a
spurious wakeup while the system is suspended, because in that case
pci_pm_suspend_noirq() will run again after pci_pm_resume_noirq()
which calls pci_restore_state(), via pci_pm_default_resume_early(),
so state_saved is cleared and the second iteration of
pci_pm_suspend_noirq() will invoke pci_prepare_to_sleep() which
may change the power state of the device.
To avoid that, add a new internal flag, skip_bus_pm, that will be set
by pci_pm_suspend_noirq() when it runs for the first time during the
given system suspend-resume cycle if the state of the device has
been saved already and the device is still in D0. Setting that flag
will cause the next iterations of pci_pm_suspend_noirq() to set
state_saved for pci_pm_resume_noirq(), so that it always restores the
device state from the originally saved data, and avoid calling
pci_prepare_to_sleep() for the device.
Fixes: 33e4f80ee69b ("ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Allow state reset of printk_once() calls.
- Prevent crashes when dereferencing invalid pointers in vsprintf().
Only the first byte is checked for simplicity.
- Make vsprintf warnings consistent and inlined.
- Treewide conversion of obsolete %pf, %pF to %ps, %pF printf
modifiers.
- Some clean up of vsprintf and test_printf code.
* tag 'printk-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
lib/vsprintf: Make function pointer_string static
vsprintf: Limit the length of inlined error messages
vsprintf: Avoid confusion between invalid address and value
vsprintf: Prevent crash when dereferencing invalid pointers
vsprintf: Consolidate handling of unknown pointer specifiers
vsprintf: Factor out %pO handler as kobject_string()
vsprintf: Factor out %pV handler as va_format()
vsprintf: Factor out %p[iI] handler as ip_addr_string()
vsprintf: Do not check address of well-known strings
vsprintf: Consistent %pK handling for kptr_restrict == 0
vsprintf: Shuffle restricted_pointer()
printk: Tie printk_once / printk_deferred_once into .data.once for reset
treewide: Switch printk users from %pf and %pF to %ps and %pS, respectively
lib/test_printf: Switch to bitmap_zalloc()
|
|
%pF and %pf are functionally equivalent to %pS and %ps conversion
specifiers. The former are deprecated, therefore switch the current users
to use the preferred variant.
The changes have been produced by the following command:
git grep -l '%p[fF]' | grep -v '^\(tools\|Documentation\)/' | \
while read i; do perl -i -pe 's/%pf/%ps/g; s/%pF/%pS/g;' $i; done
And verifying the result.
Link: http://lkml.kernel.org/r/20190325193229.23390-1-sakari.ailus@linux.intel.com
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: sparclinux@vger.kernel.org
Cc: linux-um@lists.infradead.org
Cc: xen-devel@lists.xenproject.org
Cc: linux-acpi@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: drbd-dev@lists.linbit.com
Cc: linux-block@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-nvdimm@lists.01.org
Cc: linux-pci@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: linux-btrfs@vger.kernel.org
Cc: linux-f2fs-devel@lists.sourceforge.net
Cc: linux-mm@kvack.org
Cc: ceph-devel@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: David Sterba <dsterba@suse.com> (for btrfs)
Acked-by: Mike Rapoport <rppt@linux.ibm.com> (for mm/memblock.c)
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (for drivers/pci)
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
The double underscore types are meant for compatibility in userspace
headers which does not apply here. Therefore, change to use the standard
no-underscore types.
The origin of the double underscore types dates back to before the git era
so I was not able to find a commit to see the original justification.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Remove unused lists from ASPM pcie_link_state (Frederick Lawler)
- Fix Broadcom CNB20LE host bridge unintended sign extension (Colin Ian
King)
- Expand Kconfig "PF" acronyms (Randy Dunlap)
- Update MAINTAINERS for arch/x86/kernel/early-quirks.c (Bjorn Helgaas)
- Add missing include to drivers/pci.h (Alexandru Gagniuc)
- Override Synopsys USB 3.x HAPS device class so dwc3-haps can claim it
instead of xhci (Thinh Nguyen)
- Clean up P2PDMA documentation (Randy Dunlap)
- Allow runtime PM even if driver doesn't supply callbacks (Jarkko
Nikula)
- Remove status check after submitting Switchtec MRPC Firmware Download
commands to avoid Completion Timeouts (Kelvin Cao)
- Set Switchtec coherent DMA mask to allow 64-bit DMA (Boris Glimcher)
- Fix Switchtec SWITCHTEC_IOCTL_EVENT_IDX_ALL flag overwrite issue
(Joey Zhang)
- Enable write combining for Switchtec MRPC Input buffers (Kelvin Cao)
- Add Switchtec MRPC DMA mode support (Wesley Sheng)
- Skip VF scanning on powerpc, which does this in firmware (Sebastian
Ott)
- Add Amlogic Meson PCIe controller driver and DT bindings (Yue Wang)
- Constify histb dw_pcie_host_ops structure (Julia Lawall)
- Support multiple power domains for imx6 (Leonard Crestez)
- Constify layerscape driver data (Stefan Agner)
- Update imx6 Kconfig to allow imx6 PCIe in imx7 kernel (Trent Piepho)
- Support armada8k GPIO reset (Baruch Siach)
- Support suspend/resume support on imx6 (Leonard Crestez)
- Don't hard-code DesignWare DBI/ATU offst (Stephen Warren)
- Skip i.MX6 PHY setup on i.MX7D (Andrey Smirnov)
- Remove Jianguo Sun from HiSilicon STB maintainers (Lorenzo Pieralisi)
- Mask DesignWare interrupts instead of disabling them to avoid lost
interrupts (Marc Zyngier)
- Add locking when acking DesignWare interrupts (Marc Zyngier)
- Ack DesignWare interrupts in the proper callbacks (Marc Zyngier)
- Use devm resource parser in mediatek (Honghui Zhang)
- Remove unused mediatek "num-lanes" DT property (Honghui Zhang)
- Add UniPhier PCIe controller driver and DT bindings (Kunihiko
Hayashi)
- Enable MSI for imx6 downstream components (Richard Zhu)
* tag 'pci-v4.21-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (40 commits)
PCI: imx: Enable MSI from downstream components
s390/pci: skip VF scanning
PCI/IOV: Add flag so platforms can skip VF scanning
PCI/IOV: Factor out sriov_add_vfs()
PCI: uniphier: Add UniPhier PCIe host controller support
dt-bindings: PCI: Add UniPhier PCIe host controller description
PCI: amlogic: Add the Amlogic Meson PCIe controller driver
dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller
arm64: dts: mt7622: Remove un-used property for PCIe
arm: dts: mt7623: Remove un-used property for PCIe
dt-bindings: PCI: MediaTek: Remove un-used property
PCI: mediatek: Remove un-used variant in struct mtk_pcie_port
MAINTAINERS: Remove Jianguo Sun from HiSilicon STB DWC entry
PCI: dwc: Don't hard-code DBI/ATU offset
PCI: imx: Add imx6sx suspend/resume support
PCI: armada8k: Add support for gpio controlled reset signal
PCI: dwc: Adjust Kconfig to allow IMX6 PCIe host on IMX7
PCI: dwc: layerscape: Constify driver data
PCI: imx: Add multi-pd support
PCI: Override Synopsys USB 3.x HAPS device class
...
|
|
Clang warns:
drivers/pci/pci-driver.c:1603:21: error: unused variable 'attr'
[-Werror,-Wunused-variable]
Commit e5361ca29f2f ("ACPI / scan: Refactor _CCA enforcement") removed
attr's use and replaced it with its assigned value so it is no longer
needed.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Rather than checking the DMA attribute at each callsite, just pass it
through for acpi_dma_configure() to handle directly. That can then deal
with the relatively exceptional DEV_DMA_NOT_SUPPORTED case by explicitly
installing dummy DMA ops instead of just skipping setup entirely. This
will then free up the dev->dma_ops == NULL case for some valuable
fastpath optimisations.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Tony Luck <tony.luck@intel.com>
|
|
a9c8088c7988 ("i2c: i801: Don't restore config registers on runtime PM")
nullified the runtime PM suspend/resume callback pointers while keeping the
runtime PM enabled.
This caused the SMBus PCI device to stay in D0 with
/sys/devices/.../power/runtime_status showing "error" when the runtime PM
framework attempted to autosuspend the device. This is due to PCI bus
runtime PM, which checks for driver runtime PM callbacks and returns
-ENOSYS if they are not set.
Since i2c-i801.c doesn't need to do anything device-specific for runtime
PM, Jean Delvare proposed this be fixed in the PCI core rather than adding
dummy runtime PM callback functions in the PCI drivers.
Change pci_pm_runtime_suspend()/pci_pm_runtime_resume() so they allow
changing the PCI device power state during runtime PM transitions even if
the driver supplies no runtime PM callbacks.
This fixes the runtime PM regression on i2c-i801.c.
It is not obvious why the code previously required the runtime PM
callbacks. The test has been there since the code was introduced by
6cbf82148ff2 ("PCI PM: Run-time callbacks for PCI bus type").
On the other hand, a similar change was done to generic runtime PM
callbacks in 05aa55dddb9e ("PM / Runtime: Lenient generic runtime pm
callbacks").
Fixes: a9c8088c7988 ("i2c: i801: Don't restore config registers on runtime PM")
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # v4.18+
|
|
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is supplied
(Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum (Jakub
Kicinski)
* pci/misc:
PCI: Limit config space size for Netronome NFP5000
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Unify PCI and normal DMA direction definitions
PCI: Use IRQF_ONESHOT if pci_request_irq() called with no handler
PCI: Call dma_debug_add_bus() for pci_bus_type from PCI core
PCI: Mark fall-through switch cases before enabling -Wimplicit-fallthrough
# Conflicts:
# drivers/pci/hotplug/pciehp_ctrl.c
|
|
There is nothing arch-specific about PCI or dma-debug, so call
dma_debug_add_bus() from the PCI core just after registering the bus type.
Most of dma-debug is already generic; this just adds reporting of pending
dma-allocations on driver unload for arches other than powerpc, sh, and
x86.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
|
|
The TotalVFs register in the SR-IOV capability is the hardware limit on the
number of VFs. A PF driver can limit the number of VFs further with
pci_sriov_set_totalvfs(). When the PF driver is removed, reset any VF
limit that was imposed by the driver because that limit may not apply to
other drivers.
Before 8d85a7a4f2c9 ("PCI/IOV: Allow PF drivers to limit total_VFs to 0"),
pci_sriov_set_totalvfs(pdev, 0) meant "we can enable TotalVFs virtual
functions", and the nfp driver used that to remove the VF limit when the
driver unloads.
8d85a7a4f2c9 broke that because instead of removing the VF limit,
pci_sriov_set_totalvfs(pdev, 0) actually sets the limit to zero, and that
limit persists even if another driver is loaded.
We could fix that by making the nfp driver reset the limit when it unloads,
but it seems more robust to do it in the PCI core instead of relying on the
driver.
The regression scenario is:
nfp_pci_probe (driver 1)
...
nfp_pci_remove
pci_sriov_set_totalvfs(pf->pdev, 0) # limits VFs to 0
...
nfp_pci_probe (driver 2)
nfp_rtsym_read_le("nfd_vf_cfg_max_vfs")
# no VF limit from firmware
Now driver 2 is broken because the VF limit is still 0 from driver 1.
Fixes: 8d85a7a4f2c9 ("PCI/IOV: Allow PF drivers to limit total_VFs to 0")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
[bhelgaas: changelog, rename functions]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- unify AER decoding for native and ACPI CPER sources (Alexandru
Gagniuc)
- add TLP header info to AER tracepoint (Thomas Tai)
- add generic pcie_wait_for_link() interface (Oza Pawandeep)
- handle AER ERR_FATAL by removing and re-enumerating devices, as
Downstream Port Containment does (Oza Pawandeep)
- factor out common code between AER and DPC recovery (Oza Pawandeep)
- stop triggering DPC for ERR_NONFATAL errors (Oza Pawandeep)
- share ERR_FATAL recovery path between AER and DPC (Oza Pawandeep)
- disable ASPM L1.2 substate if we don't have LTR (Bjorn Helgaas)
- respect platform ownership of LTR (Bjorn Helgaas)
- clear interrupt status in top half to avoid interrupt storm (Oza
Pawandeep)
- neaten pci=earlydump output (Andy Shevchenko)
- avoid errors when extended config space inaccessible (Gilles Buloz)
- prevent sysfs disable of device while driver attached (Christoph
Hellwig)
- use core interface to report PCIe link properties in bnx2x, bnxt_en,
cxgb4, ixgbe (Bjorn Helgaas)
- remove unused pcie_get_minimum_link() (Bjorn Helgaas)
- fix use-before-set error in ibmphp (Dan Carpenter)
- fix pciehp timeouts caused by Command Completed errata (Bjorn
Helgaas)
- fix refcounting in pnv_php hotplug (Julia Lawall)
- clear pciehp Presence Detect and Data Link Layer Status Changed on
resume so we don't miss hotplug events (Mika Westerberg)
- only request pciehp control if we support it, so platform can use
ACPI hotplug otherwise (Mika Westerberg)
- convert SHPC to be builtin only (Mika Westerberg)
- request SHPC control via _OSC if we support it (Mika Westerberg)
- simplify SHPC handoff from firmware (Mika Westerberg)
- fix an SHPC quirk that mistakenly included *all* AMD bridges as well
as devices from any vendor with device ID 0x7458 (Bjorn Helgaas)
- assign a bus number even to non-native hotplug bridges to leave
space for acpiphp additions, to fix a common Thunderbolt xHCI
hot-add failure (Mika Westerberg)
- keep acpiphp from scanning native hotplug bridges, to fix common
Thunderbolt hot-add failures (Mika Westerberg)
- improve "partially hidden behind bridge" messages from core (Mika
Westerberg)
- add macros for PCIe Link Control 2 register (Frederick Lawler)
- replace IB/hfi1 custom macros with PCI core versions (Frederick
Lawler)
- remove dead microblaze and xtensa code (Bjorn Helgaas)
- use dev_printk() when possible in xtensa and mips (Bjorn Helgaas)
- remove unused pcie_port_acpi_setup() and portdrv_acpi.c (Bjorn
Helgaas)
- add managed interface to get PCI host bridge resources from OF (Jan
Kiszka)
- add support for unbinding generic PCI host controller (Jan Kiszka)
- fix memory leaks when unbinding generic PCI host controller (Jan
Kiszka)
- request legacy VGA framebuffer only for VGA devices to avoid false
device conflicts (Bjorn Helgaas)
- turn on PCI_COMMAND_IO & PCI_COMMAND_MEMORY in pci_enable_device()
like everybody else, not in pcibios_fixup_bus() (Bjorn Helgaas)
- add generic enable function for simple SR-IOV hardware (Alexander
Duyck)
- use generic SR-IOV enable for ena, nvme (Alexander Duyck)
- add ACS quirk for Intel 7th & 8th Gen mobile (Alex Williamson)
- add ACS quirk for Intel 300 series (Mika Westerberg)
- enable register clock for Armada 7K/8K (Gregory CLEMENT)
- reduce Keystone "link already up" log level (Fabio Estevam)
- move private DT functions to drivers/pci/ (Rob Herring)
- factor out dwc CONFIG_PCI Kconfig dependencies (Rob Herring)
- add DesignWare support to the endpoint test driver (Gustavo
Pimentel)
- add DesignWare support for endpoint mode (Gustavo Pimentel)
- use devm_ioremap_resource() instead of devm_ioremap() in dra7xx and
artpec6 (Gustavo Pimentel)
- fix Qualcomm bitwise NOT issue (Dan Carpenter)
- add Qualcomm runtime PM support (Srinivas Kandagatla)
- fix DesignWare enumeration below bridges (Koen Vandeputte)
- use usleep() instead of mdelay() in endpoint test (Jia-Ju Bai)
- add configfs entries for pci_epf_driver device IDs (Kishon Vijay
Abraham I)
- clean up pci_endpoint_test driver (Gustavo Pimentel)
- update Layerscape maintainer email addresses (Minghuan Lian)
- add COMPILE_TEST to improve build test coverage (Rob Herring)
- fix Hyper-V bus registration failure caused by domain/serial number
confusion (Sridhar Pitchai)
- improve Hyper-V refcounting and coding style (Stephen Hemminger)
- avoid potential Hyper-V hang waiting for a response that will never
come (Dexuan Cui)
- implement Mediatek chained IRQ handling (Honghui Zhang)
- fix vendor ID & class type for Mediatek MT7622 (Honghui Zhang)
- add Mobiveil PCIe host controller driver (Subrahmanya Lingappa)
- add Mobiveil MSI support (Subrahmanya Lingappa)
- clean up clocks, MSI, IRQ mappings in R-Car probe failure paths
(Marek Vasut)
- poll more frequently (5us vs 5ms) while waiting for R-Car data link
active (Marek Vasut)
- use generic OF parsing interface in R-Car (Vladimir Zapolskiy)
- add R-Car V3H (R8A77980) "compatible" string (Sergei Shtylyov)
- add R-Car gen3 PHY support (Sergei Shtylyov)
- improve R-Car PHYRDY polling (Sergei Shtylyov)
- clean up R-Car macros (Marek Vasut)
- use runtime PM for R-Car controller clock (Dien Pham)
- update arm64 defconfig for Rockchip (Shawn Lin)
- refactor Rockchip code to facilitate both root port and endpoint
mode (Shawn Lin)
- add Rockchip endpoint mode driver (Shawn Lin)
- support VMD "membar shadow" feature (Jon Derrick)
- support VMD bus number offsets (Jon Derrick)
- add VMD "no AER source ID" quirk for more device IDs (Jon Derrick)
- remove unnecessary host controller CONFIG_PCIEPORTBUS Kconfig
selections (Bjorn Helgaas)
- clean up quirks.c organization and whitespace (Bjorn Helgaas)
* tag 'pci-v4.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (144 commits)
PCI/AER: Replace struct pcie_device with pci_dev
PCI/AER: Remove unused parameters
PCI: qcom: Include gpio/consumer.h
PCI: Improve "partially hidden behind bridge" log message
PCI: Improve pci_scan_bridge() and pci_scan_bridge_extend() doc
PCI: Move resource distribution for single bridge outside loop
PCI: Account for all bridges on bus when distributing bus numbers
ACPI / hotplug / PCI: Drop unnecessary parentheses
ACPI / hotplug / PCI: Mark stale PCI devices disconnected
ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug
PCI: hotplug: Add hotplug_is_native()
PCI: shpchp: Add shpchp_is_native()
PCI: shpchp: Fix AMD POGO identification
PCI: mobiveil: Add MSI support
PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver
PCI/AER: Decode Error Source Requester ID
PCI/AER: Remove aer_recover_work_func() forward declaration
PCI/DPC: Use the generic pcie_do_fatal_recovery() path
PCI/AER: Pass service type to pcie_do_fatal_recovery()
PCI/DPC: Disable ERR_NONFATAL handling by DPC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a significant update of the generic power domains
(genpd) and Operating Performance Points (OPP) frameworks, mostly
related to the introduction of power domain performance levels,
cpufreq updates (new driver for Qualcomm Kryo processors, updates of
the existing drivers, some core fixes, schedutil governor
improvements), PCI power management fixes, ACPI workaround for
EC-based wakeup events handling on resume from suspend-to-idle, and
major updates of the turbostat and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks in
the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the schedutil
cpufreq governor (Joel Fernandes, Dietmar Eggemann, Rafael Wysocki,
Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman, Viresh
Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag set
and update stale comments in the PCI core PM code (Rafael Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver (David
Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies)"
* tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (128 commits)
tools/power turbostat: update version number
tools/power turbostat: Add Node in output
tools/power turbostat: add node information into turbostat calculations
tools/power turbostat: remove num_ from cpu_topology struct
tools/power turbostat: rename num_cores_per_pkg to num_cores_per_node
tools/power turbostat: track thread ID in cpu_topology
tools/power turbostat: Calculate additional node information for a package
tools/power turbostat: Fix node and siblings lookup data
tools/power turbostat: set max_num_cpus equal to the cpumask length
tools/power turbostat: if --num_iterations, print for specific number of iterations
tools/power turbostat: Add Cannon Lake support
tools/power turbostat: delete duplicate #defines
x86: msr-index.h: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: add POLL and POLL% column
tools/power turbostat: Fix --hide Pk%pc10
tools/power turbostat: Build-in "Low Power Idle" counters support
tools/power turbostat: Don't make man pages executable
tools/power turbostat: remove blank lines
tools/power turbostat: a small C-states dump readability immprovement
...
|
|
The state_saved flag should not be cleared in pci_pm_suspend() if the
given device is going to remain suspended, or the device's config
space will not be restored properly during the subsequent resume.
Namely, if the device is going to stay in suspend, both the late
and noirq callbacks return early for it, so if its state_saved flag
is cleared in pci_pm_suspend(), it will remain unset throughout the
remaining part of suspend and resume and pci_restore_state() called
for the device going forward will return without doing anything.
For this reason, change pci_pm_suspend() to only clear state_saved
if the given device is not going to remain suspended. [This is
analogous to what commit ae860a19f37c (PCI / PM: Do not clear
state_saved in pci_pm_freeze() when smart suspend is set) did for
hibernation.]
Fixes: c4b65157aeef (PCI / PM: Take SMART_SUSPEND driver flag into account)
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Move the error reporting callbacks from aerdrv_core.c to err.c, where they
can be used by DPC in addition to AER.
As part of aerdrv_core.c, these callbacks were built under CONFIG_PCIEAER.
Moving them to the new err.c means they will now be built under
CONFIG_PCIEPORTBUS, so adjust the definition of pci_uevent_ers() to match.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: in reset_link(), initialize "driver" even if CONFIG_PCIEAER is
unset, update pci_uevent_ers() #ifdef wrapper]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
With each bus implementing its own DMA configuration callback, there is no
need for bus to explicitly set the force_dma flag. Modify the
of_dma_configure function to accept an input parameter which specifies if
implicit DMA configuration is required when it is not described by the
firmware.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI parts
Reviewed-by: Rob Herring <robh@kernel.org>
[hch: tweaked the changelog a bit]
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
ACPI/OF support for configuration of DMA is a bus specific aspect, and
thus should be configured by the bus. Introduces a 'dma_configure' bus
method so that busses can control their DMA capabilities.
Also update the PCI, Platform, ACPI and host1x buses to use the new
method.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI parts
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[hch: simplified host1x_dma_configure based on a comment from Thierry,
rewrote changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
If a driver uses DPM_FLAG_SMART_SUSPEND and the device is already
runtime suspended when hibernate is started PCI core skips runtime
resuming the device but still clears pci_dev->state_saved. After the
hibernation image is written pci_pm_thaw_noirq() makes sure subsequent
thaw phases for the device are also skipped leaving it runtime suspended
with pci_dev->state_saved == false.
When the device is eventually runtime resumed pci_pm_runtime_resume()
restores config space by calling pci_restore_standard_config(), however
because pci_dev->state_saved == false pci_restore_state() never actually
restores the config space leaving the device in a state that is not what
the driver might expect.
For example here is what happens for intel-lpss I2C devices once the
hibernation snapshot is taken:
intel-lpss 0000:00:15.0: power state changed by ACPI to D0
intel-lpss 0000:00:1e.0: power state changed by ACPI to D3cold
video LNXVIDEO:00: Restoring backlight state
PM: hibernation exit
i2c_designware i2c_designware.1: Unknown Synopsys component type: 0xffffffff
i2c_designware i2c_designware.0: Unknown Synopsys component type: 0xffffffff
i2c_designware i2c_designware.1: timeout in disabling adapter
i2c_designware i2c_designware.0: timeout in disabling adapter
Since PCI config space is not restored the device is still in D3hot
making MMIO register reads return 0xffffffff.
Fix this by clearing pci_dev->state_saved only if we actually end up
runtime resuming the device.
Fixes: c4b65157aeef (PCI / PM: Take SMART_SUSPEND driver flag into account)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- move pci_uevent_ers() out of pci.h (Michael Ellerman)
- skip ASPM common clock warning if BIOS already configured it (Sinan
Kaya)
- fix ASPM Coverity warning about threshold_ns (Gustavo A. R. Silva)
- remove last user of pci_get_bus_and_slot() and the function itself
(Sinan Kaya)
- add decoding for 16 GT/s link speed (Jay Fang)
- add interfaces to get max link speed and width (Tal Gilboa)
- add pcie_bandwidth_capable() to compute max supported link bandwidth
(Tal Gilboa)
- add pcie_bandwidth_available() to compute bandwidth available to
device (Tal Gilboa)
- add pcie_print_link_status() to log link speed and whether it's
limited (Tal Gilboa)
- use PCI core interfaces to report when device performance may be
limited by its slot instead of doing it in each driver (Tal Gilboa)
- fix possible cpqphp NULL pointer dereference (Shawn Lin)
- rescan more of the hierarchy on ACPI hotplug to fix Thunderbolt/xHCI
hotplug (Mika Westerberg)
- add support for PCI I/O port space that's neither directly accessible
via CPU in/out instructions nor directly mapped into CPU physical
memory space. This is fairly intrusive and includes minor changes to
interfaces used for I/O space on most platforms (Zhichang Yuan, John
Garry)
- add support for HiSilicon Hip06/Hip07 LPC I/O space (Zhichang Yuan,
John Garry)
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
- don't set up INTx if MSI or MSI-X is enabled to align cris, frv,
ia64, and mn10300 with x86 (Bjorn Helgaas)
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
- use generic pci_mmap_resource_range() instead of powerpc and xtensa
arch-specific versions (David Woodhouse)
- support arbitrary PCI host bridge offsets on sparc (Yinghai Lu)
- remove System and Video ROM reservations on sparc (Bjorn Helgaas)
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization
(KarimAllah Ahmed)
- consolidate VPD code in vpd.c (Bjorn Helgaas)
- add Tegra dependency on PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
- add DT support for R-Car r8a7743 (Biju Das)
- fix a PCI_EJECT vs PCI_BUS_RELATIONS race condition in Hyper-V host
bridge driver that causes a general protection fault (Dexuan Cui)
- fix Hyper-V host bridge hang in MSI setup on 1-vCPU VMs with SR-IOV
(Dexuan Cui)
- fix Hyper-V host bridge hang when ejecting a VF before setting up MSI
(Dexuan Cui)
- make several structures static (Fengguang Wu)
- increase number of MSI IRQs supported by Synopsys DesignWare bridges
from 32 to 256 (Gustavo Pimentel)
- implemented multiplexed IRQ domain API and remove obsolete MSI IRQ
API from DesignWare drivers (Gustavo Pimentel)
- add Tegra power management support (Manikanta Maddireddy)
- add Tegra loadable module support (Manikanta Maddireddy)
- handle 64-bit BARs correctly in endpoint support (Niklas Cassel)
- support optional regulator for HiSilicon STB (Shawn Guo)
- use regulator bulk API for Qualcomm apq8064 (Srinivas Kandagatla)
- support power supplies for Qualcomm msm8996 (Srinivas Kandagatla)
* tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (123 commits)
MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver
HISI LPC: Add ACPI support
ACPI / scan: Do not enumerate Indirect IO host children
ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use
HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
of: Add missing I/O range exception for indirect-IO devices
PCI: Apply the new generic I/O management on PCI IO hosts
PCI: Add fwnode handler as input param of pci_register_io_range()
PCI: Remove __weak tag from pci_register_io_range()
MAINTAINERS: Add missing /drivers/pci/cadence directory entry
fm10k: Report PCIe link properties with pcie_print_link_status()
net/mlx5e: Use pcie_bandwidth_available() to compute bandwidth
net/mlx5: Report PCIe link properties with pcie_print_link_status()
net/mlx4_core: Report PCIe link properties with pcie_print_link_status()
PCI: Add pcie_print_link_status() to log link speed and whether it's limited
PCI: Add pcie_bandwidth_available() to compute bandwidth available to device
misc: pci_endpoint_test: Handle 64-bit BARs properly
PCI: designware-ep: Make dw_pcie_ep_reset_bar() handle 64-bit BARs properly
PCI: endpoint: Make sure that BAR_5 does not have 64-bit flag set when clearing
PCI: endpoint: Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar
...
|
|
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
* pci/portdrv:
PCI/DPC: Rename from pcie-dpc.c to dpc.c
PCI/DPC: Do not enable DPC if AER control is not allowed by the BIOS
PCI/AER: Use cached AER Capability offset
PCI/portdrv: Rename and reverse sense of pcie_ports_auto
PCI/portdrv: Encapsulate pcie_ports_auto inside the port driver
PCI/portdrv: Remove unnecessary "pcie_ports=auto" parameter
PCI/portdrv: Remove "pcie_hp=nomsi" kernel parameter
PCI/portdrv: Remove unnecessary include of <linux/pci-aspm.h>
PCI/portdrv: Simplify PCIe feature permission checking
PCI/portdrv: Remove unused PCIE_PORT_SERVICE_VC
PCI/portdrv: Remove pcie_port_bus_type link order dependency
PCI/portdrv: Disable port driver in compat mode
PCI/PM: Clear PCIe PME Status bit for Root Complex Event Collectors
PCI/PM: Clear PCIe PME Status bit in core, not PCIe port driver
PCI/PM: Move pcie_clear_root_pme_status() to core
PCI/portdrv: Merge pcieport_if.h into portdrv.h
PCI/portdrv: Move pcieport_if.h to drivers/pci/pcie/
Conflicts:
drivers/pci/pcie/Makefile
drivers/pci/pcie/portdrv.h
|
