| Age | Commit message (Collapse) | Author |
|---|
|
'PTR_ERR(p) == -E*' is a stronger condition than IS_ERR(p).
Hence, IS_ERR(p) is unneeded.
The semantic patch that generates this commit is as follows:
// <smpl>
@@
expression ptr;
constant error_code;
@@
-IS_ERR(ptr) && (PTR_ERR(ptr) == - error_code)
+PTR_ERR(ptr) == - error_code
// </smpl>
Link: http://lkml.kernel.org/r/20200106045833.1725-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Stephen Boyd <sboyd@kernel.org> [drivers/clk/clk.c]
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> [GPIO]
Acked-by: Wolfram Sang <wsa@the-dreams.de> [drivers/i2c]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> [acpi/scan.c]
Acked-by: Rob Herring <robh@kernel.org>
Cc: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Using a mask to represent bus DMA constraints has a set of limitations.
The biggest one being it can only hold a power of two (minus one). The
DMA mapping code is already aware of this and treats dev->bus_dma_mask
as a limit. This quirk is already used by some architectures although
still rare.
With the introduction of the Raspberry Pi 4 we've found a new contender
for the use of bus DMA limits, as its PCIe bus can only address the
lower 3GB of memory (of a total of 4GB). This is impossible to represent
with a mask. To make things worse the device-tree code rounds non power
of two bus DMA limits to the next power of two, which is unacceptable in
this case.
In the light of this, rename dev->bus_dma_mask to dev->bus_dma_limit all
over the tree and treat it as such. Note that dev->bus_dma_limit should
contain the higher accessible DMA address.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
the comments which discribed the input parameters of of_match_device().
the name is changed, so fix it.
Signed-off-by: Jojo Zeng <jojo_zeng@126.com>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
|
|
Remove directly accessing device_node.type pointer and use the accessors
instead. This will eventually allow removing the type pointer.
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
- Add validation of NUMA distance map to prevent crashes with bad map
- Fix setting of dma_mask
* tag 'devicetree-fixes-for-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of, numa: Validate some distance map rules
of/device: Really only set bus DMA mask when appropriate
|
|
of_dma_configure() was *supposed* to be following the same logic as
acpi_dma_configure() and only setting bus_dma_mask if some range was
specified by the firmware. However, it seems that subtlety got lost in
the process of fitting it into the differently-shaped control flow, and
as a result the force_dma==true case ends up always setting the bus mask
to the 32-bit default, which is not what anyone wants.
Make sure we only touch it if the DT actually said so.
Fixes: 6c2fb2ea7636 ("of/device: Set bus DMA mask as appropriate")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Robert Richter <robert.richter@cavium.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
|
|
This goes through a lot of hooks just to call arch_teardown_dma_ops.
Replace it with a direct call instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
|
|
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Now that we can track upstream DMA constraints properly with
bus_dma_mask instead of trying (and failing) to maintain it in
coherent_dma_mask, it doesn't make much sense for the firmware code to
be touching the latter at all. It's merely papering over bugs wherein a
driver has failed to call dma_set_coherent_mask() *and* the bus code has
not initialised any default value.
We don't really want to encourage more drivers coercing dma_mask so
we'll continue to fix that up if necessary, but add a warning to help
flush out any such buggy bus code that remains.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
When an explicit DMA limit is described by firmware, we need to remember
it regardless of how drivers might subsequently update their devices'
masks. The new bus_dma_mask field does that.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
With each bus implementing its own DMA configuration callback, there is no
need for bus to explicitly set the force_dma flag. Modify the
of_dma_configure function to accept an input parameter which specifies if
implicit DMA configuration is required when it is not described by the
firmware.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI parts
Reviewed-by: Rob Herring <robh@kernel.org>
[hch: tweaked the changelog a bit]
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Convert remaining DT files to use SPDX-License-Identifier tags.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
We do not want the common dma_configure() pathway to apply
indiscriminately to all devices, since there are plenty of buses which
do not have DMA capability, and if their child devices were used for
DMA API calls it would only be indicative of a driver bug. However,
there are a number of buses for which DMA is implicitly expected even
when not described by firmware - those we whitelist with an automatic
opt-in to dma_configure(), assuming that the DMA address space and the
physical address space are equivalent if not otherwise specified.
Commit 723288836628 ("of: restrict DMA configuration") introduced a
short-term fix by comparing explicit bus types, but this approach is far
from pretty, doesn't scale well, and fails to cope at all with bus
drivers which may be built as modules, like host1x. Let's refine things
by making that opt-in a property of the bus type, which neatly addresses
those problems and lets the decision of whether firmware description of
DMA capability should be optional or mandatory stay internal to the bus
drivers themselves.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Pull dma-mapping updates from Christoph Hellwig:
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and patches
* tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping:
dma-coherent: fix dma_declare_coherent_memory() logic error
ARM: imx: mx31moboard: Remove unused 'dma' variable
dma-coherent: remove an unused variable
MAINTAINERS: use the iommu list for the dma-mapping subsystem
dma-coherent: remove the DMA_MEMORY_MAP and DMA_MEMORY_IO flags
dma-coherent: remove the DMA_MEMORY_INCLUDES_CHILDREN flag
of: restrict DMA configuration
dma-mapping: remove dma_alloc_noncoherent and dma_free_noncoherent
i825xx: switch to switch to dma_alloc_attrs
au1000_eth: switch to dma_alloc_attrs
sgiseeq: switch to dma_alloc_attrs
dma-mapping: reduce dma_mapping_error inline bloat
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"There's a few orphans in the conversion to %pOF printf specifiers
included here that no one else picked up.
Summary:
- Convert more DT code to use of_property_read_* API.
- Improve DT overlay support when adding multiple overlays
- Convert printk's to %pOF format specifiers. Most went via subsystem
trees, but picked up the remaining orphans
- Correct unittests to use preferred "okay" for "status" property
value
- Add a KASLR seed property
- Vendor prefixes for Mellanox, Theobroma System, Adaptrum, Moxa
- Fix modalias buffer handling
- Clean-up of include paths for building dtbs
- Add bindings for amc6821, isl1208, tsl2x7x, srf02, and srf10
devices
- Add nvmem bindings for MediaTek MT7623 and MT7622 SoC
- Add compatible string for Allwinner H5 Mali-450 GPU
- Fix links to old OpenFirmware docs with new mirror on
devicetree.org
- Remove status property from binding doc examples"
* tag 'devicetree-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (45 commits)
devicetree: Adjust status "ok" -> "okay" under drivers/of/
dt-bindings: Remove "status" from examples
dt-bindings: pinctrl: sh-pfc: Use generic node name
dt-bindings: Add vendor Mellanox
dt-binding: net/phy: fix interrupts description
virt: Convert to using %pOF instead of full_name
macintosh: Convert to using %pOF instead of full_name
ide: pmac: Convert to using %pOF instead of full_name
microblaze: Convert to using %pOF instead of full_name
dt-bindings: usb: musb: Grammar s/the/to/, s/is/are/
of: Use PLATFORM_DEVID_NONE definition
of/device: Fix of_device_get_modalias() buffer handling
of/device: Prevent buffer overflow in of_device_modalias()
dt-bindings: add amc6821, isl1208 trivial bindings
dt-bindings: add vendor prefix for Theobroma Systems
of: search scripts/dtc/include-prefixes path for both CPP and DTC
of: remove arch/$(SRCARCH)/boot/dts from include search path for CPP
of: remove drivers/of/testcase-data from include search path for CPP
of: return of_get_cpu_node from of_cpu_device_node_get if CPUs are not registered
iio: srf08: add device tree binding for srf02 and srf10
...
|
|
Moving DMA configuration to happen later at driver probe time had the
unnoticed side-effect that we now perform DMA configuration for *every*
device represented in DT, rather than only those explicitly created by
the of_platform and PCI code.
As Christoph points out, this is not really the best thing to do. Whilst
there may well be other DMA-capable buses that can benefit from having
their children automatically configured after the bridge has probed,
there are also plenty of others like USB, MDIO, etc. that definitely do
not support DMA and should not be indiscriminately processed.
The good news is that in most cases the DT "dma-ranges" property serves
as an appropriate indicator - per a strict interpretation of the spec,
anything lacking a "dma-ranges" property should be considered not to
have a mapping of DMA address space from its children to its parent,
thus anything for which of_dma_get_range() does not succeed does not
need DMA configuration. Certain bus types have a general expectation of
DMA capability and carry a well-established precedent that an absent
"dma-ranges" implies the same as the empty property, so we automatically
opt those in to DMA configuration regardless, to avoid regressing most
existing platforms.
Fixes: 09515ef5ddad ("of/acpi: Configure dma operations at probe time for platform/amba/pci bus devices")
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Use dedicated definition instead of plain -1 where it's appropriate.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
of_device_request_module() calls of_device_get_modalias() with "len" 0,
to calculate the size of the buffer needed to store the result, but due
to integer promotion the ssize_t "len" will be compared as unsigned with
strlen(compat) and the loop will generally never break. This results in
a call to snprintf() with a negative len, which triggers below warning,
followed by a dereference of a invalid pointer:
[ 3.060067] WARNING: CPU: 0 PID: 51 at lib/vsprintf.c:2122 vsnprintf+0x348/0x6d8
...
[ 3.060301] [<ffffff800891ede8>] vsnprintf+0x348/0x6d8
[ 3.060308] [<ffffff800891f248>] snprintf+0x48/0x50
[ 3.060316] [<ffffff80086a7c80>] of_device_get_modalias+0x108/0x160
[ 3.060322] [<ffffff80086a7cf8>] of_device_request_module+0x20/0x88
...
Further more of_device_get_modalias() is supposed to return the number
of bytes needed to store the entire modalias, so the loop needs to
continue accumulate the total size even though the buffer is full.
Finally the function is not expected to ensure space for the NUL, nor
include it in the returned size, so only 1 should be added to the length
of "compat" in the loop (to account for the character 'C').
Fixes: bc575064d688 ("of/device: use of_property_for_each_string to parse compatible strings")
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
As of_device_get_modalias() returns the number of bytes that would have
been written to the target string, regardless of how much did fit in the
buffer, it's possible that the returned index points beyond the buffer
passed to of_device_modalias() - causing memory beyond the buffer to be
null terminated.
Fixes: 0634c2958927 ("of: Add function for generating a DT modalias with a newline")
Cc: Rob Herring <robh@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Historically, DMA masks have suffered some ambiguity between whether
they represent the range of physical memory a device can access, or the
address bits a device is capable of driving, particularly since on many
platforms the two are equivalent. Whilst there are some stragglers left
(dma_max_pfn(), I'm looking at you...), the majority of DMA code has
been cleaned up to follow the latter definition, not least since it is
the only one which makes sense once IOMMUs are involved.
In this respect, of_dma_configure() has always done the wrong thing in
how it generates initial masks based on "dma-ranges". Although rounding
down did not affect the TI Keystone platform where dma_addr + size is
already a power of two, in any other case it results in a mask which is
at best unnecessarily constrained and at worst unusable.
BCM2837 illustrates the problem nicely, where we have a DMA base of 3GB
and a size of 1GB - 16MB, giving dma_addr + size = 0xff000000 and a
resultant mask of 0x7fffffff, which is then insufficient to even cover
the necessary offset, effectively making all DMA addresses out-of-range.
This has been hidden until now (mostly because we don't yet prevent
drivers from simply overwriting this initial mask later upon probe), but
due to recent changes elsewhere now shows up as USB being broken on
Raspberry Pi 3.
Make it right by rounding up instead of down, such that the mask
correctly correctly describes all possisble bits the device needs to
emit.
Fixes: 9a6d7298b083 ("of: Calculate device DMA masks based on DT dma-range size")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Andreas Färber <afaerber@suse.de>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Instead of directly parsing the compatible property, use the
of_property_for_each_string() helper to iterate over each compatible
string. This reduces the LoC and makes the functions easier to
understand.
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
While deferring the probe of IOMMU masters, xlate and
add_device callbacks called from of_iommu_configure
can pass back error values like -ENODEV, which means
the IOMMU cannot be connected with that master for real
reasons. Before the IOMMU probe deferral, all such errors
were ignored. Now all those errors are propagated back,
killing the master's probe for such errors. Instead ignore
all the errors except EPROBE_DEFER, which is the only one
of concern and let the master work without IOMMU, thus
restoring the old behavior. Also make explicit that
of_dma_configure handles only -EPROBE_DEFER from
of_iommu_configure.
Fixes: 7b07cbefb68d ("iommu: of: Handle IOMMU lookup failure with deferred probing or error")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Magnus Damn <magnus.damn@gmail.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- code optimizations for the Intel VT-d driver
- ability to switch off a previously enabled Intel IOMMU
- support for 'struct iommu_device' for OMAP, Rockchip and Mediatek
IOMMUs
- header optimizations for IOMMU core code headers and a few fixes that
became necessary in other parts of the kernel because of that
- ACPI/IORT updates and fixes
- Exynos IOMMU optimizations
- updates for the IOMMU dma-api code to bring it closer to use per-cpu
iova caches
- new command-line option to set default domain type allocated by the
iommu core code
- another command line option to allow the Intel IOMMU switched off in
a tboot environment
- ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using an
IDENTITY domain in conjunction with DMA ops, Support for SMR masking,
Support for 16-bit ASIDs (was previously broken)
- various other small fixes and improvements
* tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (63 commits)
soc/qbman: Move dma-mapping.h include to qman_priv.h
soc/qbman: Fix implicit header dependency now causing build fails
iommu: Remove trace-events include from iommu.h
iommu: Remove pci.h include from trace/events/iommu.h
arm: dma-mapping: Don't override dma_ops in arch_setup_dma_ops()
ACPI/IORT: Fix CONFIG_IOMMU_API dependency
iommu/vt-d: Don't print the failure message when booting non-kdump kernel
iommu: Move report_iommu_fault() to iommu.c
iommu: Include device.h in iommu.h
x86, iommu/vt-d: Add an option to disable Intel IOMMU force on
iommu/arm-smmu: Return IOVA in iova_to_phys when SMMU is bypassed
iommu/arm-smmu: Correct sid to mask
iommu/amd: Fix incorrect error handling in amd_iommu_bind_pasid()
iommu: Make iommu_bus_notifier return NOTIFY_DONE rather than error code
omap3isp: Remove iommu_group related code
iommu/omap: Add iommu-group support
iommu/omap: Make use of 'struct iommu_device'
iommu/omap: Store iommu_dev pointer in arch_data
iommu/omap: Move data structures to omap-iommu.h
iommu/omap: Drop legacy-style device support
...
|
|
Failures to look up an IOMMU when parsing the DT iommus property need to
be handled separately from the .of_xlate() failures to support deferred
probing.
The lack of a registered IOMMU can be caused by the lack of a driver for
the IOMMU, the IOMMU device probe not having been performed yet, having
been deferred, or having failed.
The first case occurs when the device tree describes the bus master and
IOMMU topology correctly but no device driver exists for the IOMMU yet
or the device driver has not been compiled in. Return NULL, the caller
will configure the device without an IOMMU.
The second and third cases are handled by deferring the probe of the bus
master device which will eventually get reprobed after the IOMMU.
The last case is currently handled by deferring the probe of the bus
master device as well. A mechanism to either configure the bus master
device without an IOMMU or to fail the bus master device probe depending
on whether the IOMMU is optional or mandatory would be a good
enhancement.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pichart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Size of the dma-range is calculated as coherent_dma_mask + 1
and passed to arch_setup_dma_ops further. It overflows when
the coherent_dma_mask is set for full 64 bits 0xFFFFFFFFFFFFFFFF,
resulting in size getting passed as 0 wrongly. Fix this by
passsing in max(mask, mask + 1). Note that in this case
when the mask is set to full 64bits, we will be passing the mask
itself to arch_setup_dma_ops instead of the size. The real fix
for this should be to make arch_setup_dma_ops receive the
mask and handle it, to be done in the future.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
As part of moving DMA initializing to probe time the
of_dma_deconfigure() function will need to be called from different
source files. Make it public and move it to drivers/of/device.c where
the of_dma_configure() function is.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The modalias sysfs attr is lacking a newline for DT aliases on platform
devices. The macio and ibmebus correctly add the newline, but open code it.
Introduce a new function, of_device_modalias(), that fills the buffer with
the modalias including the newline and update users of the old
of_device_get_modalias function.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the length of the modalias is greater than the buffer size, then the
modalias is truncated. However the untruncated length is returned which
will cause an error. Fix this to return the truncated length. If an error
in the case was desired, then then we should just return -ENOMEM.
The reality is no device will ever have 4KB of compatible strings to hit
this case.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
|
|
The ULPI bus can be built as a module, and it will soon be
calling these functions when it supports probing devices from DT.
Export them so they can be used by the ULPI module.
Acked-by: Rob Herring <robh@kernel.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
In the case of ULPI devices, we want to be able to load the
driver before registering the device so that we don't get stuck
in a loop waiting for the phy module to appear and failing usb
controller probe. Currently we request the ulpi module via the
ulpi ids, but in the DT case we might need to request it with the
OF based modalias instead. Add a common function that allows
anyone to request a module with the OF based modalias.
Acked-by: Rob Herring <robh@kernel.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
As a set of driver-provided callbacks and static data, there is no
compelling reason for struct iommu_ops to be mutable in core code, so
enforce const-ness throughout.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
For now, in function device_add, the new device will be forced to
inherit the numa node of its parent. But this will override the device's
numa node which configured in devicetree.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's a common operation for device drivers to retrive the data
member from of_device_id struct in their probe function.
Most driver end up doing:
const struct of_device_id *match;
match = of_match_device(driver_of_match, &pdev->dev);
driver->data = match->data;
With the of_device_get_match_data helper function all this can
done in one go.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
[robh: add missing inline to dummmy declaration]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Calculate the dma_mask and coherent_dma_mask based on the dma-range values
set in DT for the device.
Limit the mask to lower of the default mask and mask calculated.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Will Deacon <will.deacon@arm.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
|
|
Fix the dma-range size when the DT attribute is missing, i.e., set size to
dev->coherent_dma_mask + 1 instead of dev->coherent_dma_mask. Also add
code to check invalid values of size configured in DT and log error.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> (AMD Seattle)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: Arnd Bergmann <arnd@arndb.de>
|
|
Move of_dma_configure() to device.c so it can be re-used for PCI devices to
obtain DMA configuration from DT. Also add a second argument so that for
PCI, the DT node of root bus host bridge can be used to obtain the DMA
configuration for the slave PCI device.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> (AMD Seattle)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
CC: Joerg Roedel <joro@8bytes.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: Arnd Bergmann <arnd@arndb.de>
|
|
We're overloading usage of of_aliases_mutex for sysfs changes,
so rename to something that is more generic.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
Fix a problem that, the platform bus supports the OF style modalias
in .uevent() call, but not in its device 'modalias' sysfs attribute.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In some situations, userspace may want to resolve a
device by function and logical number (ie, "serial0")
rather than by the base address or full device path. Being
able to resolve a device by alias frees userspace from the
burden of otherwise having to maintain a mapping between
device addresses and their logical assignments on each
platform when multiple instances of the same hardware block
are present in the system.
Although the uevent device attribute contains devicetree
compatible information and the full device path, the uevent
does not list the alises that may have been defined for the
device.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
[grant.likely: Removed OF_ALIAS_N field; I don't think it's needed]
[grant.likely: Added #ifndef _LINUX_OF_PRIVATE_H wrapper]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
When userspace needs to find a specific device, it currently isn't easy to
resolve a /sys/devices/ path from a specific device tree node. Nor is it
easy to obtain the compatible list for devices.
This patch generalizes the code that inserts OF_* values into the uevent
device attribute so that any device that is attached to an OF node will
have that information exported to userspace. Without this patch only
platform devices and some powerpc-specific busses have access to this
data.
The original function also creates a MODALIAS property for the compatible
list, but that code has not been generalized into the common case because
it has the potential to break module loading on a lot of bus types. Bus
types are still responsible for their own MODALIAS properties.
Boot tested on ARM and compile tested on PowerPC and SPARC.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Frederic Lambert <frdrc66@gmail.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Mark Brown <broonie@sirena.org.uk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
arch/powerpc/kernel/ibmebus.c is the only remaining user of the
of_bus_type support code for initializing the bus and registering
drivers. All others have either been switched to the vanilla platform
bus or already have their own infrastructure.
This patch moves the functionality that ibmebus is using out of
drivers/of/{platform,device}.c and into ibmebus.c where it is actually
used. Also renames the moved symbols from of_platform_* to
ibmebus_bus_* to reflect the actual usage.
This patch is part of moving all of the of_platform_bus_type users
over to the platform_bus_type.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The current code allocates and manages platform_devices created from
the device tree manually. It also uses an unsafe shortcut for
allocating the platform_device and the resource table at the same
time. (which I added in the last rework; sorry).
This patch refactors the code to use platform_device_alloc() for
allocating new devices. This reduces the amount of custom code
implemented by of_platform, eliminates the unsafe alloc trick, and has
the side benefit of letting the platform_bus code manage freeing the
device data and resources when the device is freed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <monstr@monstr.eu>
|
|
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
|
|
of_device is currently just an #define alias to platform_device until it
gets removed entirely. This patch removes references to it from the
include directories and the core drivers/of code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
of_platform_bus was being used in the same manner as the platform_bus.
The only difference being that of_platform_bus devices are generated
from data in the device tree, and platform_bus devices are usually
statically allocated in platform code. Having them separate causes
the problem of device drivers having to be registered twice if it
was possible for the same device to appear on either bus.
This patch removes of_platform_bus_type and registers all of_platform
bus devices and drivers on the platform bus instead. A previous patch
made the of_device structure an alias for the platform_device structure,
and a shim is used to adapt of_platform_drivers to the platform bus.
After all of of_platform_bus drivers are converted to be normal platform
drivers, the shim code can be removed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
Add of_driver_match_device() helper function. This function can be used
by bus types to determine if a driver works with a device when using OF
style matching. If CONFIG_OF is unselected, then it is a nop.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Michal Simek <monstr@monstr.eu>
CC: Grant Likely <grant.likely@secretlab.ca>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
CC: linux-kernel@vger.kernel.org
CC: microblaze-uclinux@itee.uq.edu.au
CC: linuxppc-dev@ozlabs.org
CC: devicetree-discuss@lists.ozlabs.org
|
|
Now that the of_node pointer is part of struct device,
of_device_get_modalias could be used on any struct device
that has the device node pointer set. This patch changes
of_device_get_modalias to accept a struct device instead
of a struct of_device.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: Michal Simek <monstr@monstr.eu>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Wolfram Sang <w.sang@pengutronix.de>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
CC: microblaze-uclinux@itee.uq.edu.au
CC: linuxppc-dev@ozlabs.org
|
