| Age | Commit message (Collapse) | Author |
|---|
|
If a failure occurs when creating Debug FS entries, unroll all of
the work that's been done.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The ntb_perf tool uses module parameters to control the
characteristics of its test. Enable the changing of these
options through debugfs, and eliminating the need to unload
and reload the module to make changes and run additional tests.
Add a new module parameter that forces the DMA channel
selection onto the same node as the NTB device (default: true).
- seg_order: Size of the NTB memory window; power of 2.
- run_order: Size of the data buffer; power of 2.
- use_dma: Use DMA or memcpy? Default: 0.
- on_node: Only use DMA channel(s) on the NTB node. Default: true.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The Debug FS entries manage themselves; we don't need to hang onto
them in the context structure.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The DMA channel(s)/memory used to transfer data to an NTB device
may not be required to be on the same node as the device. Add a
module parameter that allows any candidate channel (aside from
node assocation) and allocated memory to be used.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
IDT 89HPESxNTx device series is PCIe-switches, which support
Non-Transparent bridging between domains connected to the device ports.
Since new NTB API exposes multi-port interface and messaging API, the
IDT NT-functions can be now supported in the kernel. This driver adds
the following functionality:
1) Multi-port NTB API to have information of possible NT-functions
activated in compliance with available device ports.
2) Memory windows of direct and look up table based address translation
with all possible combinations of BARs setup.
3) Traditional doorbell NTB API.
4) One-on-one messaging NTB API.
There are some IDT PCIe-switch setups, which must be done before any of
the NTB peers started. It can be performed either by system BIOS via
IDT SMBus-slave interface or by pre-initialized IDT PCIe-switch EEPROM:
1) NT-functions of corresponding ports must be activated using
SWPARTxCTL and SWPORTxCTL registers.
2) BAR0 must be configured to expose NT-function configuration
registers map.
3) The rest of the BARs must have at least one memory window
configured, otherwise the driver will just return an error.
Temperature sensor of IDT PCIe-switches can be also optionally
activated by BIOS or EEPROM.
(See IDT documentations for details of how the pre-initialization can
be done)
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
As per a comments in [1] by Greg Kroah-Hartman, the ndev_* macros should
be cleaned up. This makes it more clear what's actually going on when
reading the code.
[1] http://www.spinics.net/lists/linux-pci/msg56904.html
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
As per a comments in [1] by Greg Kroah-Hartman, the ndev_* macros should
be cleaned up. This makes it more clear what's actually going on when
reading the code.
[1] http://www.spinics.net/lists/linux-pci/msg56904.html
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Some IDT NTB-capable PCIe-switches have message registers to communicate with
peer devices. This patch adds new NTB API callback methods, which can be used
to utilize these registers functionality:
ntb_msg_count(); - get number of message registers
ntb_msg_inbits(); - get bitfield of inbound message registers status
ntb_msg_outbits(); - get bitfield of outbound message registers status
ntb_msg_read_sts(); - read the inbound and outbound message registers status
ntb_msg_clear_sts(); - clear status bits of message registers
ntb_msg_set_mask(); - mask interrupts raised by status bits of message
registers.
ntb_msg_clear_mask(); - clear interrupts mask bits of message registers
ntb_msg_read(midx, *pidx); - read message register with specified index,
additionally getting peer port index which data received from
ntb_msg_write(midx, pidx); - write data to the specified message register
sending it to the passed peer device connected over a pidx port
ntb_msg_event(); - notify driver context of a new message event
Of course there is hardware which doesn't support Message registers, so
this API is made optional.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Even though there is no any real NTB hardware, which would have both more
than two ports and Scratchpad registers, it is logically correct to have
Scratchpad API accepting a peer port index as well. Intel/AMD drivers utilize
Primary and Secondary topology to split Scratchpad between connected root
devices. Since port-index API introduced, Intel/AMD NTB hardware drivers can
use device port to determine which Scratchpad registers actually belong to
local and peer devices. The same approach can be used if some potential
hardware in future will be multi-port and have some set of Scratchpads.
Here are the brief of changes in the API:
ntb_spad_count() - return number of Scratchpads per each port
ntb_peer_spad_addr(pidx, sidx) - address of Scratchpad register of the
peer device with pidx-index
ntb_peer_spad_read(pidx, sidx) - read specified Scratchpad register of the
peer with pidx-index
ntb_peer_spad_write(pidx, sidx) - write data to Scratchpad register of the
peer with pidx-index
Since there is hardware which doesn't support Scratchpad registers, the
corresponding API methods are now made optional.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Multi-port NTB devices permit to share a memory between all accessible peers.
Memory Windows API is altered to correspondingly initialize and map memory
windows for such devices:
ntb_mw_count(pidx); - number of inbound memory windows, which can be allocated
for shared buffer with specified peer device.
ntb_mw_get_align(pidx, widx); - get alignment and size restriction parameters
to properly allocate inbound memory region.
ntb_peer_mw_count(); - get number of outbound memory windows.
ntb_peer_mw_get_addr(widx); - get mapping address of an outbound memory window
If hardware supports inbound translation configured on the local ntb port:
ntb_mw_set_trans(pidx, widx); - set translation address of allocated inbound
memory window so a peer device could access it.
ntb_mw_clear_trans(pidx, widx); - clear the translation address of an inbound
memory window.
If hardware supports outbound translation configured on the peer ntb port:
ntb_peer_mw_set_trans(pidx, widx); - set translation address of a memory
window retrieved from a peer device
ntb_peer_mw_clear_trans(pidx, widx); - clear the translation address of an
outbound memory window
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Multi-port devices permit the NTB connections between multiple domains,
so a local device can have NTB link being up with one peer and being
down with another. NTB link-state API is appropriately altered to return
a bitfield of the link-states between the local device and possible peers.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
There is some NTB hardware, which can combine more than just two domains
over NTB. For instance, some IDT PCIe-switches can have NTB-functions
activated on more than two-ports. The different domains are distinguished
by ports they are connected to. So the new port-related methods are added to
the NTB API:
ntb_port_number() - return local port
ntb_peer_port_count() - return number of peers local port can connect to
ntb_peer_port_number(pdix) - return port number by it index
ntb_peer_port_idx(port) - return port index by it number
Current test-drivers aren't changed much. They still support two-ports devices
for the time being while multi-ports hardware drivers aren't added.
By default port-related API is declared for two-ports hardware.
So corresponding hardware drivers won't need to implement it.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Do not sleep in ntb_async_tx_submit, which could deadlock.
This reverts commit "8c874cc140d667f84ae4642bb5b5e0d6396d2ca4"
Fixes: 8c874cc140d6 ("NTB: Address out of DMA descriptor issue with NTB")
Reported-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Allen Hubbe <Allen.Hubbe@dell.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Fixing doorbell register length to 32bits per spec. On Skylake NTB, the
doorbell registers are 32bit write only registers. The source for the
doorbell is a 64bit register that shows the interrupt bits.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 783dfa6cc41b ("ntb: Adding Skylake Xeon NTB support")
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
A divide by zero error occurs if qp_count is less than mw_count because
num_qps_mw is calculated to be zero. The calculation appears to be
incorrect.
The requirement is for num_qps_mw to be set to qp_count / mw_count
with any remainder divided among the earlier mws.
For example, if mw_count is 5 and qp_count is 12 then mws 0 and 1
will have 3 qps per window and mws 2 through 4 will have 2 qps per window.
Thus, when mw_num < qp_count % mw_count, num_qps_mw is 1 higher
than when mw_num >= qp_count.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Fixes: e26a5843f7f5 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
In cases where there are more mw's than spads/2-2, the mw count gets
reduced to match the limitation. ntb_transport also tries to ensure that
there are fewer qps than mws but uses the full mw count instead of
the reduced one. When this happens, the math in
'ntb_transport_setup_qp_mw' will get confused and result in a kernel
paging request bug.
This patch fixes the bug by reducing qp_count to the reduced mw count
instead of the full mw count.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Fixes: e26a5843f7f5 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The order parameters are powers of 2; adjust the usage information
to use correct mathematical representations.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Fixes: 8a7b6a778a85 ("ntb: ntb perf tool")
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
On Skylake hardware, the link_poll isn't clearing the pending interrupt
bit. Adding a new function for SKX that handles clearing of status bit the
right way.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 783dfa6c ("ntb: Adding Skylake Xeon NTB support")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Fix typo causing ntb_transport_create_queue to select the first
queue every time, instead of using the next free queue.
Signed-off-by: Thomas VanSelus <tvanselus@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Fixes: fce8a7bb5 ("PCI-Express Non-Transparent Bridge Support")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
In the normal I/O execution path, ntb_perf is missing a call to
dmaengine_unmap_put() after submission. That causes us to leak
unmap objects.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 8a7b6a77 ("ntb: ntb perf tool")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The call to debugfs_remove_recursive(qp->debugfs_dir) of the sub-level
directory must not be later than
debugfs_remove_recursive(nt_debugfs_dir) of the top-level directory.
Otherwise, the sub-level directory will not exist, and it would be
invalid (panic) to attempt to remove it. This removes the top-level
directory last, after sub-level directories have been cleaned up.
Signed-off-by: Allen Hubbe <Allen.Hubbe@dell.com>
Fixes: e26a5843f ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The results were previously ignored, anyway.
Signed-off-by: Steve Wahl <Steve.Wahl@dell.com>
Fixes: e26a5843f7f5014ae4460030ca4de029a3ac35d3
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
'request_irq()' and 'free_irq()' should have the same 'dev_id'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The offsets for the SZ registers are wrong. Updated.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reported-by: Sandeep Mann <sandeep@purestorage.com>
Tested-by: Zachary Ross <zacharyx.ross@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
When the underlying NTB H/W driver advertises more memory windows
than the number of scratchpads available to setup MW's, it is likely
that we may end up filling the remaining memory windows with garbage.
So to avoid that, lets limit the memory windows that transport driver
can setup based on the available scratchpads.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Due to incorrect limit and translation register values, NTB link was
going down when the memory window was setup. Made appropriate changes
as per spec.
Fix limit register values for BAR1, which was overlapping
with the BAR23 address.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
AMD NTB support hotplug under B2B mode. NTB will trigger link
up/down interrupt event when doing plug add/remove, this patch
implements the two interrupt event to support B2B hotplug function.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The Skylake Xeon NTB hardware has made some changes to the register name,
offset, and the way doorbells work. Adding driver support for the new
hardware.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
This is a static checker warning, not something I'm desperately
concerned about. But snprintf() returns the number of bytes that
would have been copied if there were space. We really care about the
number of bytes that actually were copied so we should use scnprintf()
instead.
It probably won't overrun, and in that case we may as well just use
sprintf() but these sorts of things make static checkers and code
reviewers happier.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The peer_addr member of intel_ntb_dev is not set, therefore when
acquiring ntb_peer_db and ntb_peer_spad we only get the offset rather
than the actual physical address. Adding fix to correct that.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
schedule_timeout_* takes a timeout in jiffies but the code currently is
passing in a constant which makes this timeout HZ dependent, so pass it
through msecs_to_jiffies() to fix this up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
schedule_timeout_* takes a timeout in jiffies but the code currently is
passing in a constant which makes this timeout HZ dependent, so pass it
through msecs_to_jiffies() to fix this up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Fix typo in module parameter descriptions.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Fix 'db_init' parameter description.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Adding support on the rx DMA path to allow recovery of errors when
DMA responds with error status and abort all the subsequent ops.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: linux-ntb@googlegroups.com
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Adding support on the tx DMA path to allow recovery of errors when
DMA responds with error status and abort all the subsequent ops.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: linux-ntb@googlegroups.com
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Clean up duplicated expression by replacing it with the equivalent local
variable pdev.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
It will be useful to know the hardware configured BAR size to diagnose
issues with NTB memory windows.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
When the link goes down, the link_is_up flag did not return to
false. This could have caused some subtle corner case bugs
when the link goes up and down quickly.
Once that was fixed, there was found to be a race if the link was
brought down then immediately up. The link_cleanup work would
occasionally be scheduled after the next link up event. This would
cancel the link_work that was supposed to occur and leave ntb_perf
in an unusable state.
To fix this we get rid of the link_cleanup work and put the actions
directly in the link_down event.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
This commit adds a debugfs 'count' file to ntb_pingpong. This is so
testing with ntb_pingpong can be automated beyond just checking the
logs for pong messages.
The count file returns a number which increments every pong. The
counter can be cleared by writing a zero.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
In order to more successfully script with ntb_tool it's useful to
have a link file to check the link status so that the script
doesn't use the other files until the link is up.
This commit adds a 'link' file to the debugfs directory which reads
boolean (Y or N) depending on the link status. Writing to the file
change the link state using ntb_link_enable or ntb_link_disable.
A 'link_event' file is also provided so an application can block until
the link changes to the desired state. If the user writes a 1, it will
block until the link is up. If the user writes a 0, it will block until
the link is down.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
In order to make the interface closer to the raw NTB API, this commit
changes memory windows so they are not initialized on link up.
Instead, the 'peer_trans*' debugfs files are introduced. When read,
they return information provided by ntb_mw_get_range. When written,
they create a buffer and initialize the memory window. The
value written is taken as the requested size of the buffer (which
is then rounded for alignment). Writing a value of zero frees the buffer
and tears down the memory window translation. The 'peer_mw*' file is
only created once the memory window translation is setup by the user.
Additionally, it was noticed that the read and write functions for the
'peer_mw*' files should have checked for a NULL pointer.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Instead of returning immediately with an error when the link is
down, wait for the link to come up (or the user sends a SIGINT).
This is to make scripting ntb_perf easier.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Instead of having to watch logs, allow the results to be retrieved
by reading back the run file. This file will return "running" when
the test is running and nothing if no tests have been run yet.
It returns 1 line per thread, and will display an error message if the
corresponding thread returns an error.
With the above change, the pr_info calls that returned the results are
then changed to pr_debug calls.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
This commit accomplishes a few things:
1) Properly prevent multiple sets of threads from running at once using
a mutex. Lots of race issues existed with the thread_cleanup.
2) The mutex allows us to ensure that threads are finished before
tearing down the device or module.
3) Don't use kthread_stop when the threads can exit by themselves, as
this is counter-indicated by the kthread_create documentation. Threads
now wait for kthread_stop to occur.
4) Writing to the run file now blocks until the threads are complete.
The test can then be safely interrupted by a SIGINT.
Also, while I was at it:
5) debugfs_run_write shouldn't return 0 in the early check cases as this
could cause debugfs_run_write to loop undesirably.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
When debugging performance problems, if some issue causes the ntb
hardware to be significantly slower than expected, ntb_perf will
hang requiring a reboot because it only schedules once every 4GB.
Instead, schedule based on jiffies so it will not hang the CPU if
the transfer is slow.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
I'm working on hardware that currently has a limited number of
scratchpad registers and ntb_ndev fails with no clue as to why. I
feel it is better to fail early and provide a reasonable error message
then to fail later on.
The same is done to ntb_perf, but it doesn't currently require enough
spads to actually fail. I've also removed the unused SPAD_MSG and
SPAD_ACK enums so that MAX_SPAD accurately reflects the number of
spads used.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
We allocate some memory window buffers when the link comes up, then we
provide debugfs files to read/write each side of the link.
This is useful for debugging the mapping when writing new drivers.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
On my system, dma_alloc_coherent won't produce memory anywhere
near the size of the BAR. So I needed a way to limit this.
It's pretty much copied straight from ntb_transport.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Currently we only allocate a fixed default number of descriptors for the tx
and rx side. We should dynamically resize it to the number of descriptors
resides in the transport rings. We should know the number of transmit
descriptors at initializaiton. We will allocate the default number of
descriptors for receive side and allocate additional ones when we know the
actual max entries for receive.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <allen.hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
