| Age | Commit message (Collapse) | Author |
|---|
|
This is preventive cleanup that may save troubles later.
No need to cancel repeateadly queued work if code is properly
refactored.
Don't let the ethtool -s process interfere with the stat workqueue
scheduling.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Preemption disabled at:
[<ffff000008cabd54>] dev_set_rx_mode+0x1c/0x38
Call trace:
[<ffff00000808a5c0>] dump_backtrace+0x0/0x3d0
[<ffff00000808a9a4>] show_stack+0x14/0x20
[<ffff000008e6c0c0>] dump_stack+0xac/0xe4
[<ffff0000080fe76c>] ___might_sleep+0x164/0x238
[<ffff0000080fe890>] __might_sleep+0x50/0x88
[<ffff0000082261e4>] kmem_cache_alloc+0x17c/0x1d0
[<ffff000000ea0ae8>] ocelot_set_rx_mode+0x108/0x188 [mscc_ocelot_common]
[<ffff000008cabcf0>] __dev_set_rx_mode+0x58/0xa0
[<ffff000008cabd5c>] dev_set_rx_mode+0x24/0x38
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a DP_INFO message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a BNX2X_ERR message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a bond is enslaved to another bond, bond_netdev_event() only
handles the event as if the bond is a master, and skips treating the
bond as a slave.
This leads to a refcount leak on the slave, since we don't remove the
adjacency to its master and the master holds a reference on the slave.
Reproducer:
ip link add bondL type bond
ip link add bondU type bond
ip link set bondL master bondU
ip link del bondL
No "Fixes:" tag, this code is older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.1
Second set of fixes for 5.1.
iwlwifi
* add some new PCI IDs (plus a struct name change they depend on)
* fix crypto with new devices, namely 22560 and above
* fix for a potential deadlock in the TX path
* a fix for offloaded rate-control
* support new PCI HW IDs which use a new FW
mt76
* fix lock initialisation and a possible deadlock
* aggregation fixes
rt2x00
* fix sequence numbering during retransmits
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-04-09
This series provides some fixes to mlx5 driver.
I've cc'ed some of the checksum fixes to Eric Dumazet and i would like to get
his feedback before you pull.
For -stable v4.19
('net/mlx5: FPGA, tls, idr remove on flow delete')
('net/mlx5: FPGA, tls, hold rcu read lock a bit longer')
For -stable v4.20
('net/mlx5e: Rx, Check ip headers sanity')
('Revert "net/mlx5e: Enable reporting checksum unnecessary also for L3 packets"')
('net/mlx5e: Rx, Fixup skb checksum for packets with tail padding')
For -stable v5.0
('net/mlx5e: Switch to Toeplitz RSS hash by default')
('net/mlx5e: Protect against non-uplink representor for encap')
('net/mlx5e: XDP, Avoid checksum complete when XDP prog is loaded')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Separate the overflow handling from the hardware interrupt status analysis.
The interrupt status is a single register and is common for all PFs. The
first PF reading the register is not necessarily the one who overflowed.
All PFs must check their overflow status on every attention.
In this change we clear the sticky indication in the attention handler to
allow doorbells to be processed again as soon as possible, but running
the doorbell recovery is scheduled for the periodic handler to reduce the
time spent in the attention handler.
Checking the need for DORQ flush was changed to "db_bar_no_edpm" because
qed_edpm_enabled()'s result could change dynamically and might have
prevented a needed flush.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the DORQ (doorbell block) is overflowed, all PFs get attentions at the
same time. If one PF finished handling the attention before another PF even
started, the second PF might miss the DORQ's attention bit and not handle
the attention at all.
If the DORQ attention is missed and the issue is not resolved, another
attention will not be sent, therefore each attention is treated as a
potential DORQ attention.
As a result, the attention callback is called more frequently so the debug
print was moved to reduce its quantity.
The number of periodic doorbell recovery handler schedules was reduced
because it was the previous way to mitigating the missed attention issue.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the condition which verifies that doorbell address is inside the
doorbell bar by checking that the end of the address is within range
as well.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DB_REC_DRY_RUN (running doorbell recovery without sending doorbells) is
never used. DB_REC_ONCE (send a single doorbell from the doorbell recovery)
is not needed anymore because by running the periodic handler we make sure
we check the overflow status later instead.
This patch is needed because in the next patches, the only doorbell
recovery type being used is DB_REC_REAL_DEAL, and the fixes are much
cleaner without this enum.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The err2 error return path calls qede_ptp_disable that cleans up
on an error and frees ptp. After this, the free'd ptp is dereferenced
when ptp->clock is set to NULL and the code falls-through to error
path err1 that frees ptp again.
Fix this by calling qede_ptp_disable and exiting via an error
return path that does not set ptp->clock or kfree ptp.
Addresses-Coverity: ("Write to pointer after free")
Fixes: 035744975aec ("qede: Add support for PTP resource locking.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently if a pci dma mapping failure is detected a free'd
memblock address is returned rather than a NULL (that indicates
an error). Fix this by ensuring NULL is returned on this error case.
Addresses-Coverity: ("Use after free")
Fixes: 528f727279ae ("vxge: code cleanup and reorganization")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Second batch of iwlwifi fixes intended for v5.1
* fix for a potential deadlock in the TX path;
* a fix for offloaded rate-control;
* support new PCI HW IDs which use a new FW;
|
|
Move ieee80211_tx_status_ext() outside of status_list lock section
in order to avoid locking dependency and possible deadlock reposed by
LOCKDEP in below warning.
Also do mt76_tx_status_lock() just before it's needed.
[ 440.224832] WARNING: possible circular locking dependency detected
[ 440.224833] 5.1.0-rc2+ #22 Not tainted
[ 440.224834] ------------------------------------------------------
[ 440.224835] kworker/u16:28/2362 is trying to acquire lock:
[ 440.224836] 0000000089b8cacf (&(&q->lock)->rlock#2){+.-.}, at: mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.224842]
but task is already holding lock:
[ 440.224842] 000000002cfedc59 (&(&sta->lock)->rlock){+.-.}, at: ieee80211_stop_tx_ba_cb+0x32/0x1f0 [mac80211]
[ 440.224863]
which lock already depends on the new lock.
[ 440.224863]
the existing dependency chain (in reverse order) is:
[ 440.224864]
-> #3 (&(&sta->lock)->rlock){+.-.}:
[ 440.224869] _raw_spin_lock_bh+0x34/0x40
[ 440.224880] ieee80211_start_tx_ba_session+0xe4/0x3d0 [mac80211]
[ 440.224894] minstrel_ht_get_rate+0x45c/0x510 [mac80211]
[ 440.224906] rate_control_get_rate+0xc1/0x140 [mac80211]
[ 440.224918] ieee80211_tx_h_rate_ctrl+0x195/0x3c0 [mac80211]
[ 440.224930] ieee80211_xmit_fast+0x26d/0xa50 [mac80211]
[ 440.224942] __ieee80211_subif_start_xmit+0xfc/0x310 [mac80211]
[ 440.224954] ieee80211_subif_start_xmit+0x38/0x390 [mac80211]
[ 440.224956] dev_hard_start_xmit+0xb8/0x300
[ 440.224957] __dev_queue_xmit+0x7d4/0xbb0
[ 440.224968] ip6_finish_output2+0x246/0x860 [ipv6]
[ 440.224978] mld_sendpack+0x1bd/0x360 [ipv6]
[ 440.224987] mld_ifc_timer_expire+0x1a4/0x2f0 [ipv6]
[ 440.224989] call_timer_fn+0x89/0x2a0
[ 440.224990] run_timer_softirq+0x1bd/0x4d0
[ 440.224992] __do_softirq+0xdb/0x47c
[ 440.224994] irq_exit+0xfa/0x100
[ 440.224996] smp_apic_timer_interrupt+0x9a/0x220
[ 440.224997] apic_timer_interrupt+0xf/0x20
[ 440.224999] cpuidle_enter_state+0xc1/0x470
[ 440.225000] do_idle+0x21a/0x260
[ 440.225001] cpu_startup_entry+0x19/0x20
[ 440.225004] start_secondary+0x135/0x170
[ 440.225006] secondary_startup_64+0xa4/0xb0
[ 440.225007]
-> #2 (&(&sta->rate_ctrl_lock)->rlock){+.-.}:
[ 440.225009] _raw_spin_lock_bh+0x34/0x40
[ 440.225022] rate_control_tx_status+0x4f/0xb0 [mac80211]
[ 440.225031] ieee80211_tx_status_ext+0x142/0x1a0 [mac80211]
[ 440.225035] mt76x02_send_tx_status+0x2e4/0x340 [mt76x02_lib]
[ 440.225037] mt76x02_tx_status_data+0x31/0x40 [mt76x02_lib]
[ 440.225040] mt76u_tx_status_data+0x51/0xa0 [mt76_usb]
[ 440.225042] process_one_work+0x237/0x5d0
[ 440.225043] worker_thread+0x3c/0x390
[ 440.225045] kthread+0x11d/0x140
[ 440.225046] ret_from_fork+0x3a/0x50
[ 440.225047]
-> #1 (&(&list->lock)->rlock#8){+.-.}:
[ 440.225049] _raw_spin_lock_bh+0x34/0x40
[ 440.225052] mt76_tx_status_skb_add+0x51/0x100 [mt76]
[ 440.225054] mt76x02u_tx_prepare_skb+0xbd/0x116 [mt76x02_usb]
[ 440.225056] mt76u_tx_queue_skb+0x5f/0x180 [mt76_usb]
[ 440.225058] mt76_tx+0x93/0x190 [mt76]
[ 440.225070] ieee80211_tx_frags+0x148/0x210 [mac80211]
[ 440.225081] __ieee80211_tx+0x75/0x1b0 [mac80211]
[ 440.225092] ieee80211_tx+0xde/0x110 [mac80211]
[ 440.225105] __ieee80211_tx_skb_tid_band+0x72/0x90 [mac80211]
[ 440.225122] ieee80211_send_auth+0x1f3/0x360 [mac80211]
[ 440.225141] ieee80211_auth.cold.40+0x6c/0x100 [mac80211]
[ 440.225156] ieee80211_mgd_auth.cold.50+0x132/0x15f [mac80211]
[ 440.225171] cfg80211_mlme_auth+0x149/0x360 [cfg80211]
[ 440.225181] nl80211_authenticate+0x273/0x2e0 [cfg80211]
[ 440.225183] genl_family_rcv_msg+0x196/0x3a0
[ 440.225184] genl_rcv_msg+0x47/0x8e
[ 440.225185] netlink_rcv_skb+0x3a/0xf0
[ 440.225187] genl_rcv+0x24/0x40
[ 440.225188] netlink_unicast+0x16d/0x210
[ 440.225189] netlink_sendmsg+0x204/0x3b0
[ 440.225191] sock_sendmsg+0x36/0x40
[ 440.225193] ___sys_sendmsg+0x259/0x2b0
[ 440.225194] __sys_sendmsg+0x47/0x80
[ 440.225196] do_syscall_64+0x60/0x1f0
[ 440.225197] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 440.225198]
-> #0 (&(&q->lock)->rlock#2){+.-.}:
[ 440.225200] lock_acquire+0xb9/0x1a0
[ 440.225202] _raw_spin_lock_bh+0x34/0x40
[ 440.225204] mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.225215] ieee80211_agg_start_txq+0xe8/0x2b0 [mac80211]
[ 440.225225] ieee80211_stop_tx_ba_cb+0xb8/0x1f0 [mac80211]
[ 440.225235] ieee80211_ba_session_work+0x1c1/0x2f0 [mac80211]
[ 440.225236] process_one_work+0x237/0x5d0
[ 440.225237] worker_thread+0x3c/0x390
[ 440.225239] kthread+0x11d/0x140
[ 440.225240] ret_from_fork+0x3a/0x50
[ 440.225240]
other info that might help us debug this:
[ 440.225241] Chain exists of:
&(&q->lock)->rlock#2 --> &(&sta->rate_ctrl_lock)->rlock --> &(&sta->lock)->rlock
[ 440.225243] Possible unsafe locking scenario:
[ 440.225244] CPU0 CPU1
[ 440.225244] ---- ----
[ 440.225245] lock(&(&sta->lock)->rlock);
[ 440.225245] lock(&(&sta->rate_ctrl_lock)->rlock);
[ 440.225246] lock(&(&sta->lock)->rlock);
[ 440.225247] lock(&(&q->lock)->rlock#2);
[ 440.225248]
*** DEADLOCK ***
[ 440.225249] 5 locks held by kworker/u16:28/2362:
[ 440.225250] #0: 0000000048fcd291 ((wq_completion)phy0){+.+.}, at: process_one_work+0x1b5/0x5d0
[ 440.225252] #1: 00000000f1c6828f ((work_completion)(&sta->ampdu_mlme.work)){+.+.}, at: process_one_work+0x1b5/0x5d0
[ 440.225254] #2: 00000000433d2b2c (&sta->ampdu_mlme.mtx){+.+.}, at: ieee80211_ba_session_work+0x5c/0x2f0 [mac80211]
[ 440.225265] #3: 000000002cfedc59 (&(&sta->lock)->rlock){+.-.}, at: ieee80211_stop_tx_ba_cb+0x32/0x1f0 [mac80211]
[ 440.225276] #4: 000000009d7b9a44 (rcu_read_lock){....}, at: ieee80211_agg_start_txq+0x33/0x2b0 [mac80211]
[ 440.225286]
stack backtrace:
[ 440.225288] CPU: 2 PID: 2362 Comm: kworker/u16:28 Not tainted 5.1.0-rc2+ #22
[ 440.225289] Hardware name: LENOVO 20KGS23S0P/20KGS23S0P, BIOS N23ET55W (1.30 ) 08/31/2018
[ 440.225300] Workqueue: phy0 ieee80211_ba_session_work [mac80211]
[ 440.225301] Call Trace:
[ 440.225304] dump_stack+0x85/0xc0
[ 440.225306] print_circular_bug.isra.38.cold.58+0x15c/0x195
[ 440.225307] check_prev_add.constprop.48+0x5f0/0xc00
[ 440.225309] ? check_prev_add.constprop.48+0x39d/0xc00
[ 440.225311] ? __lock_acquire+0x41d/0x1100
[ 440.225312] __lock_acquire+0xd98/0x1100
[ 440.225313] ? __lock_acquire+0x41d/0x1100
[ 440.225315] lock_acquire+0xb9/0x1a0
[ 440.225317] ? mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.225319] _raw_spin_lock_bh+0x34/0x40
[ 440.225321] ? mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.225323] mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.225334] ieee80211_agg_start_txq+0xe8/0x2b0 [mac80211]
[ 440.225344] ieee80211_stop_tx_ba_cb+0xb8/0x1f0 [mac80211]
[ 440.225354] ieee80211_ba_session_work+0x1c1/0x2f0 [mac80211]
[ 440.225356] process_one_work+0x237/0x5d0
[ 440.225358] worker_thread+0x3c/0x390
[ 440.225359] ? wq_calc_node_cpumask+0x70/0x70
[ 440.225360] kthread+0x11d/0x140
[ 440.225362] ? kthread_create_on_node+0x40/0x40
[ 440.225363] ret_from_fork+0x3a/0x50
Cc: stable@vger.kernel.org
Fixes: 88046b2c9f6d ("mt76: add support for reporting tx status with skb")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently rt2x00 devices retransmit the management frames with
incremented sequence number if hardware is assigning the sequence.
This is HW bug fixed already for non-QOS data frames, but it should
be fixed for management frames except beacon.
Without fix retransmitted frames have wrong SN:
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1648, FN=0, Flags=........C Frame is not being retransmitted 1648 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1649, FN=0, Flags=....R...C Frame is being retransmitted 1649 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1650, FN=0, Flags=....R...C Frame is being retransmitted 1650 1
With the fix SN stays correctly the same:
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=........C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
Cc: stable@vger.kernel.org
Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@vivint.com>
[sgruszka: simplify code, change comments and changelog]
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Now that the sequence number allocation is fixed, we can finally send a BAR
at powersave wakeup time to refresh the receiver side reorder window
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If the MT_TXD3_SN_VALID flag is not set in the tx descriptor, the hardware
assigns the sequence number. However, the rest of the code assumes that the
sequence number specified in the 802.11 header gets transmitted.
This was causing issues with the aggregation setup, which worked for the
initial one (where the sequence numbers were still close), but not for
further teardown/re-establishing of sessions.
Additionally, the overwrite of the TID sequence number in WTBL2 was resetting
the hardware assigned sequence numbers, causing them to drift further apart.
Fix this by using the software assigned sequence numbers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes lockdep complaint and a potential race condition
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Some SOC like i.MX6SX clock have some limits:
- ahb clock should be disabled before ipg.
- ahb and ipg clocks are required for MAC MII bus.
So, move the ahb clock to runtime management together with
ipg clock.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The thunderx driver forbids to load an eBPF program if the MTU is too high,
but this can be circumvented by loading the eBPF, then raising the MTU.
Fix this by limiting the MTU if an eBPF program is already loaded.
Fixes: 05c773f52b96e ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The thunderx driver splits frames bigger than 1530 bytes to multiple
pages, making impossible to run an eBPF program on it.
This leads to a maximum MTU of 1508 if QinQ is in use.
The thunderx driver forbids to load an eBPF program if the MTU is higher
than 1500 bytes. Raise the limit to 1508 so it is possible to use L2
protocols which need some more headroom.
Fixes: 05c773f52b96e ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After adding a team interface to bridge, the team interface will enter
promisc mode. Then if we add a new slave to team0, the slave will keep
promisc off. Fix it by setting slave to promisc on if team master is
already in promisc mode, also do the same for allmulti.
v2: add promisc and allmulti checking when delete ports
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While determining offload capabilities of backing hardware during
a device reset, the driver is clobbering current feature settings.
Update hw_features on reset instead of features unless a feature
is enabled that is no longer supported on the current backing device.
Also enable features that were not supported prior to the reset but
were previously enabled or requested by the user.
This can occur if the reset is the result of a carrier change, such
as a device failover or partition migration.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable Generic Receive Offload in the ibmvnic driver.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Spectrum-1, when a multicast packet is admitted to the shared buffer
it increases the quotas of all the ports and {port, TC} to which it is
forwarded to.
The above means that multicast packets are accounted multiple times in
the shared buffer and can therefore cause the associated shared buffer
pool to fill up very quickly.
To work around this issue, commit e83c045e53d7 ("mlxsw:
spectrum_buffers: Configure MC pool") added a dedicated multicast pool
in which multicast packets are accounted.
The issue is not present in Spectrum-2, but in order to be backward
compatible with Spectrum-1, its default behavior is to allow a multicast
packet to increase multiple egress quotas instead of one.
Until the new (non-backward compatible) mode is supported, configure a
dedicated multicast pool as in Spectrum-1.
Fixes: fe099bf682ab ("mlxsw: spectrum_buffers: Add Spectrum-2 shared buffer configuration")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC
addresses") enabled the driver to veto router interface (RIF) MAC
addresses that it cannot support.
This check should only be performed for interfaces for which the driver
actually configures a RIF. A VRF upper is not one of them, so ignore it.
Without this patch it is not possible to set an IP address on the VRF
device and use it as a loopback.
Fixes: 74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The workqueue is used to periodically update the networking stack about
activity / statistics of various objects such as neighbours and TC
actions.
It should not be called as part of memory reclaim path, so remove the
WQ_MEM_RECLAIM flag.
Fixes: 3d5479e92087 ("mlxsw: core: Remove deprecated create_workqueue")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ordered workqueue is used to offload various objects such as routes
and neighbours in the order they are notified.
It should not be called as part of memory reclaim path, so remove the
WQ_MEM_RECLAIM flag. This can also result in a warning [1], if a worker
tries to flush a non-WQ_MEM_RECLAIM workqueue.
[1]
[97703.542861] workqueue: WQ_MEM_RECLAIM mlxsw_core_ordered:mlxsw_sp_router_fib6_event_work [mlxsw_spectrum] is flushing !WQ_MEM_RECLAIM events:rht_deferred_worker
[97703.542884] WARNING: CPU: 1 PID: 32492 at kernel/workqueue.c:2605 check_flush_dependency+0xb5/0x130
...
[97703.542988] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
[97703.543049] Workqueue: mlxsw_core_ordered mlxsw_sp_router_fib6_event_work [mlxsw_spectrum]
[97703.543061] RIP: 0010:check_flush_dependency+0xb5/0x130
...
[97703.543071] RSP: 0018:ffffb3f08137bc00 EFLAGS: 00010086
[97703.543076] RAX: 0000000000000000 RBX: ffff96e07740ae00 RCX: 0000000000000000
[97703.543080] RDX: 0000000000000094 RSI: ffffffff82dc1934 RDI: 0000000000000046
[97703.543084] RBP: ffffb3f08137bc20 R08: ffffffff82dc18a0 R09: 00000000000225c0
[97703.543087] R10: 0000000000000000 R11: 0000000000007eec R12: ffffffff816e4ee0
[97703.543091] R13: ffff96e06f6a5c00 R14: ffff96e077ba7700 R15: ffffffff812ab0c0
[97703.543097] FS: 0000000000000000(0000) GS:ffff96e077a80000(0000) knlGS:0000000000000000
[97703.543101] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[97703.543104] CR2: 00007f8cd135b280 CR3: 00000001e860e003 CR4: 00000000003606e0
[97703.543109] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[97703.543112] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[97703.543115] Call Trace:
[97703.543129] __flush_work+0xbd/0x1e0
[97703.543137] ? __cancel_work_timer+0x136/0x1b0
[97703.543145] ? pwq_dec_nr_in_flight+0x49/0xa0
[97703.543154] __cancel_work_timer+0x136/0x1b0
[97703.543175] ? mlxsw_reg_trans_bulk_wait+0x145/0x400 [mlxsw_core]
[97703.543184] cancel_work_sync+0x10/0x20
[97703.543191] rhashtable_free_and_destroy+0x23/0x140
[97703.543198] rhashtable_destroy+0xd/0x10
[97703.543254] mlxsw_sp_fib_destroy+0xb1/0xf0 [mlxsw_spectrum]
[97703.543310] mlxsw_sp_vr_put+0xa8/0xc0 [mlxsw_spectrum]
[97703.543364] mlxsw_sp_fib_node_put+0xbf/0x140 [mlxsw_spectrum]
[97703.543418] ? mlxsw_sp_fib6_entry_destroy+0xe8/0x110 [mlxsw_spectrum]
[97703.543475] mlxsw_sp_router_fib6_event_work+0x6cd/0x7f0 [mlxsw_spectrum]
[97703.543484] process_one_work+0x1fd/0x400
[97703.543493] worker_thread+0x34/0x410
[97703.543500] kthread+0x121/0x140
[97703.543507] ? process_one_work+0x400/0x400
[97703.543512] ? kthread_park+0x90/0x90
[97703.543523] ret_from_fork+0x35/0x40
Fixes: a3832b31898f ("mlxsw: core: Create an ordered workqueue for FIB offload")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Semion Lisyansky <semionl@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EMAD workqueue is used to handle retransmission of EMAD packets that
contain configuration data for the device's firmware.
Given the workers need to allocate these packets and that the code is
not called as part of memory reclaim path, remove the WQ_MEM_RECLAIM
flag.
Fixes: d965465b60ba ("mlxsw: core: Fix possible deadlock")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver cannot guarantee in the prepare phase that it will be able to
write an MDB entry to the device. In case the driver returned success
during the prepare phase, but then failed to add the entry in the commit
phase, a WARNING [1] will be generated by the switchdev core.
Fix this by doing the work in the prepare phase instead.
[1]
[ 358.544486] swp12s0: Commit of object (id=2) failed.
[ 358.550061] WARNING: CPU: 0 PID: 30 at net/switchdev/switchdev.c:281 switchdev_port_obj_add_now+0x9b/0xe0
[ 358.560754] CPU: 0 PID: 30 Comm: kworker/0:1 Not tainted 5.0.0-custom-13382-gf2449babf221 #1350
[ 358.570472] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016
[ 358.580582] Workqueue: events switchdev_deferred_process_work
[ 358.587001] RIP: 0010:switchdev_port_obj_add_now+0x9b/0xe0
...
[ 358.614109] RSP: 0018:ffffa6b900d6fe18 EFLAGS: 00010286
[ 358.619943] RAX: 0000000000000000 RBX: ffff8b00797ff000 RCX: 0000000000000000
[ 358.627912] RDX: ffff8b00b7a1d4c0 RSI: ffff8b00b7a152e8 RDI: ffff8b00b7a152e8
[ 358.635881] RBP: ffff8b005c3f5bc0 R08: 000000000000022b R09: 0000000000000000
[ 358.643850] R10: 0000000000000000 R11: ffffa6b900d6fcc8 R12: 0000000000000000
[ 358.651819] R13: dead000000000100 R14: ffff8b00b65a23c0 R15: 0ffff8b00b7a2200
[ 358.659790] FS: 0000000000000000(0000) GS:ffff8b00b7a00000(0000) knlGS:0000000000000000
[ 358.668820] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 358.675228] CR2: 00007f00aad90de0 CR3: 00000001ca80d000 CR4: 00000000001006f0
[ 358.683188] Call Trace:
[ 358.685918] switchdev_port_obj_add_deferred+0x13/0x60
[ 358.691655] switchdev_deferred_process+0x6b/0xf0
[ 358.696907] switchdev_deferred_process_work+0xa/0x10
[ 358.702548] process_one_work+0x1f5/0x3f0
[ 358.707022] worker_thread+0x28/0x3c0
[ 358.711099] ? process_one_work+0x3f0/0x3f0
[ 358.715768] kthread+0x10d/0x130
[ 358.719369] ? __kthread_create_on_node+0x180/0x180
[ 358.724815] ret_from_fork+0x35/0x40
Fixes: 3a49b4fde2a1 ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although XOR hash function can perform very well on some special use
cases, to align with all drivers, mlx5 driver should use Toeplitz hash
by default.
Toeplitz is more stable for the general use case and it is more standard
and reliable.
On top of that, since XOR (MLX5_RX_HASH_FN_INVERTED_XOR8) gives only a
repeated 8 bits pattern. When used for udp tunneling RSS source port
manipulation it results in fixed source port, which will cause bad RSS
spread.
Fixes: 2be6967cdbc9 ("net/mlx5e: Support ETH_RSS_HASH_XOR")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This reverts commit b820e6fb0978f9c2ac438c199d2bb2f35950e9c9.
Prior the commit we are reverting, checksum unnecessary was only set when
both the L3 OK and L4 OK bits are set on the CQE. This caused packets
of IP protocols such as SCTP which are not dealt by the current HW L4
parser (hence the L4 OK bit is not set, but the L4 header type none bit
is set) to go through the checksum none code, where currently we wrongly
report checksum unnecessary for them, a regression. Fix this by a revert.
Note that on our usual track we report checksum complete, so the revert
isn't expected to have any notable performance impact. Also, when we are
not on the checksum complete track, the L4 protocols for which we report
checksum none are not high performance ones, we will still report
checksum unnecessary for UDP/TCP.
Fixes: b820e6fb0978 ("net/mlx5e: Enable reporting checksum unnecessary also for L3 packets")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Avi Urman <aviu@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
TC encap offload is supported only for the physical uplink
representor. Fail for non uplink representor.
Fixes: 3e621b19b0bb ("net/mlx5e: Support TC encapsulation offloads with upper devices")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In the two places is_last_ethertype_ip is being called, the caller will
be looking inside the ip header, to be safe, add ip{4,6} header sanity
check. And return true only on valid ip headers, i.e: the whole header
is contained in the linear part of the skb.
Note: Such situation is very rare and hard to reproduce, since mlx5e
allocates a large enough headroom to contain the largest header one can
imagine.
Fixes: fe1dc069990c ("net/mlx5e: don't set CHECKSUM_COMPLETE on SCTP packets")
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When an ethernet frame with ip payload is padded, the padding octets are
not covered by the hardware checksum.
Prior to the cited commit, skb checksum was forced to be CHECKSUM_NONE
when padding is detected. After it, the kernel will try to trim the
padding bytes and subtract their checksum from skb->csum.
In this patch we fixup skb->csum for any ip packet with tail padding of
any size, if any padding found.
FCS case is just one special case of this general purpose patch, hence,
it is removed.
Fixes: 88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"),
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
XDP programs might change packets data contents which will make the
reported skb checksum (checksum complete) invalid.
When XDP programs are loaded/unloaded set/clear rx RQs
MLX5E_RQ_STATE_NO_CSUM_COMPLETE flag.
Fixes: 86994156c736 ("net/mlx5e: XDP fast RX drop bpf programs support")
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When requested to recover from error, the tx reporter might open new
channels and close the existing ones. Use safe channels switch flow in
order to guarantee opened channels at the end of the recover flow.
For this purpose, define mlx5e_safe_reopen_channels function and use it
within those flows.
Fixes: de8650a82071 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Skip recover operation if interface is in down state as TX objects are
not open. This fixes a bug were the recover flow re-opened TX objects
which were not opened before, leading to a possible memory leak at
driver unload.
Fixes: de8650a82071 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Flow is kfreed on mlx5_fpga_tls_del_flow but kept in the idr data
structure, this is risky and can cause use-after-free, since the
idr_remove is delayed until tls_send_teardown_cmd completion.
Instead of delaying idr_remove, in this patch we do it on
mlx5_fpga_tls_del_flow, before actually kfree(flow).
Added synchronize_rcu before kfree(flow)
Fixes: ab412e1dd7db ("net/mlx5: Accel, add TLS rx offload routines")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
To avoid use-after-free, hold the rcu read lock until we are done copying
flow data into the command buffer.
Fixes: ab412e1dd7db ("net/mlx5: Accel, add TLS rx offload routines")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes:
* iTXQ fixes from Felix
* tracing fix - increase message length
* fix SW_CRYPTO_CONTROL enforcement
* WMM rule handling for regdomain intersection
* max_interfaces in hwsim - reported by syzbot
* clear private data in some more commands
* a clang compiler warning fix
I added a patch with two new (unused) macros for
rate-limited printing to simplify getting the users
into the tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the RX completion indicates RX buffers errors, the RX ring will be
disabled by firmware and no packets will be received on that ring from
that point on. Recover by resetting the device.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is logic to check that the RX/TPA consumer index is the expected
index to work around a hardware problem. However, the potentially bad
consumer index is first used to index into an array to reference an entry.
This can potentially crash if the bad consumer index is beyond legal
range. Improve the logic to use the consumer index for dereferencing
after the validity check and log an error message.
Fixes: fa7e28127a5a ("bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure SKBTX_HW_TSTAMP (i.e. SOF_TIMESTAMPING_TX_HARDWARE) has been
enabled for this skb. It does fix the issue where normal socks that
aren't expecting a timestamp will not wake up on select, but when a
user does want a SOF_TIMESTAMPING_TX_HARDWARE it does work.
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qlcnic driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.
For example, the following test will print "False":
u16 speed = SPEED_UNKNOWN;
if (speed == SPEED_UNKNOWN)
printf("True");
else
printf("False");
Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3 driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.
For example, the following test will print "False":
u16 speed = SPEED_UNKNOWN;
if (speed == SPEED_UNKNOWN)
printf("True");
else
printf("False");
Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's a significant number of reports that re-enabling ASPM causes
different issues, ranging from decreased performance to system not
booting at all. This affects only a minority of users, but the number
of affected users is big enough that we better switch off ASPM again.
This will hurt notebook users who are not affected by the issues, they
may see decreased battery runtime w/o ASPM. With the PCI core folks is
being discussed to add generic sysfs attributes to control ASPM.
Once this is in place brave enough users can re-enable ASPM on their
system.
Fixes: a99790bf5c7f ("r8169: Reinstate ASPM Support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 89cea7493a346 ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If we just set this to 2048, and have multiple limits you
can select from, the total number might run over and cause
a warning in cfg80211. This doesn't make sense, so we just
calculate the total max_interfaces now.
Reported-by: syzbot+8f91bd563bbff230d0ee@syzkaller.appspotmail.com
Fixes: 99e3a44bac37 ("mac80211_hwsim: allow setting iftype support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
