| Age | Commit message (Collapse) | Author |
|---|
|
The commit fbf68229ffe7 ("net: stmmac: unify registers dumps methods")
in the Linux kernel modified the register dump to store the DMA registers
at the DMA register offset (0x1000) but ethtool (stmmac.c) looks for the
DMA registers after the MAC registers which is offset 55.
This patch copies the DMA registers from the higher offset to the offset
where ethtool expects them.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.13
Important, but small in size, fixes.
brcmfmac
* fix a regression in SDIO support introduced in v4.13-rc1
rtlwifi
* fix a regression in bluetooth coexistance introduced in v4.13-rc1
iwlwifi
* a few NULL pointer dereferences in the recovery flow
* a small but important fix for IBSS
* a one-liner fix for tracing, which was including too much data
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each FIB node holds a linked list of routes sharing the same prefix and
length. In the case of IPv4 it's ordered according to table ID, metric
and TOS and only the first route in the list is actually programmed to
the device.
In case a gatewayed route is added somewhere in the list, then after its
nexthop group will be refreshed and become valid (due to the resolution
of its gateway), it'll mistakenly overwrite the existing entry.
Example:
192.168.200.0/24 dev enp3s0np3 scope link metric 1000 offload
192.168.200.0/24 via 192.168.100.1 dev enp3s0np3 metric 1000 offload
Both routes are marked as offloaded despite the fact only the first one
should actually be present in the device's table.
When refreshing the nexthop group, don't write the route to the device's
table unless it's the first in its node.
Fixes: 9aecce1c7d97 ("mlxsw: spectrum_router: Correctly handle identical routes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mediatek ethernet driver uses interrupts but does not explicitly
include linux/interrupt.h, relying on implicit includes. Fix this so we
don't get build breaks as happened for ARM in next-20170720.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is some codes of tun/tap module which did not check the return
value of register_netdevice_notifier. Add the check now.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Potential dangerous invalid memory might be accessed if invalid mac value
reflected from the forward port field in rxd4 caused by possible potential
hardware defects. So added a simple sanity checker to avoid the kind of
situation happening.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A hardware/firmware error may happen at any point in time. In
particular, it might happen while mac80211 is in the middle of
a flow. We observed the following situation:
* mac80211 is in authentication flow, in ieee80211_prep_connection()
* iwlwifi firmware crashes, but no error can be reported at this
precise point (mostly because the driver method is void, but even
if it wasn't we'd just shift to a race condition)
* mac80211 continues the flow, trying to add the AP station
* iwlwifi has already set its internal restart flag, and so thinks
that adding the station is part of the restart and already set up,
so it uses the information that's supposed to already be in the
struct
This can happen with any flow in mac80211 and with any information
we try to preserve across hardware restarts.
To fix this, only set a new HW_RESTART_REQUESTED flag and translate
that to IN_HW_RESTART once mac80211 actually starts the restart by
calling our start() method. As a consequence, any mac80211 flow in
progress at the time of the restart will properly finish (certainly
with errors), before the restart is attempted.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299.
Reported-by: djagoo <dev@djagoo.io>
Reported-by: Łukasz Siudut <lsiudut@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When IBSS was implemented for DQA, we missid a few places where it
should be handled in the same way as AP.
Fixes: ee48b72211f8 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
iwl_trace_data is somewhat confusing. It returns a bool
that tells if the payload of the skb should be added to
the tx_data event. If it returns false, then the payload
of the skb is added to the tx event.
The purpose is to be able to start tracing with
-e iwlwifi
and record non-data packets only which saves bandwidth.
Since EAPOLs are important, seldom and not real data
packet (despite being WiFi data packets), they are
included in tx event and thus iwl_trace_data returns false
on those. This last part was buggy, and because of that,
all the data packets were included in the tx event.
Fix that.
Fixes: 0c4cb7314d15 ("iwlwifi: tracing: decouple from mac80211")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We don't set the error code here so we end up returning ERR_PTR(0) which
is NULL. The caller doesn't expect that so it results in a NULL
dereference.
Fixes: 2e5d4a8f61dc ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Sometimes, we can have an firmware crash while trying to
recover from a previous firmware problem.
When that happens, lots of things can go wrong. For example
the stations don't get added properly to mvm->fw_id_to_mac_id.
Mac80211 tries to stop A-MPDU upon reconfig but in case of
a firmware crash we will bail out fairly early and in the
end, we won't delete the A-MPDU Rx timeout.
When that timer expired after a double firmware crash,
we end up dereferencing mvm->fw_id_to_mac_id[sta_id]
which is NULL.
Fixes: 10b2b2019d81 ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Before TVQM, all TX queues were allocated straight at init.
With TVQM, queues are allocated on demand and hence we need
to check if a queue exists before dereferencing it.
Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
iwlagn_check_ratid_empty takes the tid as a parameter, but
it doesn't check that it is not IWL_TID_NON_QOS.
Since IWL_TID_NON_QOS = 8 and iwl_priv::tid_data is an array
with 8 entries, accessing iwl_priv::tid_data[IWL_TID_NON_QOS]
is a bad idea.
This happened in iwlagn_rx_reply_tx. Since
iwlagn_check_ratid_empty is relevant only to check whether
we can open A-MPDU, this flow is irrelevant if tid is
IWL_TID_NON_QOS. Call iwlagn_check_ratid_empty only inside
the
if (tid != IWL_TID_NON_QOS)
a few lines earlier in the function.
Cc: <stable@vger.kernel.org>
Reported-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Tested-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This reverts commit f95d95a7cd5514549dcf6ba754f0ee834cce3e1f.
With commit f95d95a7cd55 ("rtlwifi: btcoex: rtl8723be: fix ant_sel not
work"), the kernel has a NULL pointer dereference oops. This content and
the proper fix will be included in a later patch.
Fixes: f95d95a7cd55 ("rtlwifi: btcoex: rtl8723be: fix ant_sel not work")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Recent change in brcmf_sdio_txpkt_hdalign() changed the
behavior and now always returns 0. This resulted in a
regression which basically renders the device useless.
Fixes: 270a6c1f65fe ("brcmfmac: rework headroom check in .start_xmit()")
Reported-by: S. Gilles <sgilles@math.umd.edu>
Tested-by: S. Gilles <sgilles@math.umd.edu>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Pull networking fixes from David Miller:
1) BPF verifier signed/unsigned value tracking fix, from Daniel
Borkmann, Edward Cree, and Josef Bacik.
2) Fix memory allocation length when setting up calls to
->ndo_set_mac_address, from Cong Wang.
3) Add a new cxgb4 device ID, from Ganesh Goudar.
4) Fix FIB refcount handling, we have to set it's initial value before
the configure callback (which can bump it). From David Ahern.
5) Fix double-free in qcom/emac driver, from Timur Tabi.
6) A bunch of gcc-7 string format overflow warning fixes from Arnd
Bergmann.
7) Fix link level headroom tests in ip_do_fragment(), from Vasily
Averin.
8) Fix chunk walking in SCTP when iterating over error and parameter
headers. From Alexander Potapenko.
9) TCP BBR congestion control fixes from Neal Cardwell.
10) Fix SKB fragment handling in bcmgenet driver, from Doug Berger.
11) BPF_CGROUP_RUN_PROG_SOCK_OPS needs to check for null __sk, from Cong
Wang.
12) xmit_recursion in ppp driver needs to be per-device not per-cpu,
from Gao Feng.
13) Cannot release skb->dst in UDP if IP options processing needs it.
From Paolo Abeni.
14) Some netdev ioctl ifr_name[] NULL termination fixes. From Alexander
Levin and myself.
15) Revert some rtnetlink notification changes that are causing
regressions, from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
net: bonding: Fix transmit load balancing in balance-alb mode
rds: Make sure updates to cp_send_gen can be observed
net: ethernet: ti: cpsw: Push the request_irq function to the end of probe
ipv4: initialize fib_trie prior to register_netdev_notifier call.
rtnetlink: allocate more memory for dev_set_mac_address()
net: dsa: b53: Add missing ARL entries for BCM53125
bpf: more tests for mixed signed and unsigned bounds checks
bpf: add test for mixed signed and unsigned bounds checks
bpf: fix up test cases with mixed signed/unsigned bounds
bpf: allow to specify log level and reduce it for test_verifier
bpf: fix mixed signed/unsigned derived min/max value bounds
ipv6: avoid overflow of offset in ip6_find_1stfragopt
net: tehuti: don't process data if it has not been copied from userspace
Revert "rtnetlink: Do not generate notifications for CHANGEADDR event"
net: dsa: mv88e6xxx: Enable CMODE config support for 6390X
dt-binding: ptp: Add SoC compatibility strings for dte ptp clock
NET: dwmac: Make dwmac reset unconditional
net: Zero terminate ifr_name in dev_ifname().
wireless: wext: terminate ifr name coming from userspace
netfilter: fix netfilter_net_init() return
...
|
|
balance-alb mode used to have transmit dynamic load balancing feature
enabled by default. However, transmit dynamic load balancing no longer
works in balance-alb after commit 8b426dc54cf4 ("bonding: remove
hardcoded value").
Both balance-tlb and balance-alb use the function bond_do_alb_xmit() to
send packets. This function uses the parameter tlb_dynamic_lb.
tlb_dynamic_lb used to have the default value of 1 for balance-alb, but
now the value is set to 0 except in balance-tlb.
Re-enable transmit dyanmic load balancing by initializing tlb_dynamic_lb
for balance-alb similar to balance-tlb.
Fixes: 8b426dc54cf4 ("bonding: remove hardcoded value")
Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Push the request_irq function to the end of probe so as
to ensure all the required fields are populated in the event
of an ISR getting executed right after requesting the irq.
Currently while loading the crash kernel a crash was seen as
soon as devm_request_threaded_irq was called. This was due to
n->poll being NULL which is called as part of net_rx_action
function.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BCM53125 entry was missing an arl_entries member which would
basically prevent the ARL search from terminating properly. This switch
has 4 ARL entries, so add that.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The array data is only populated with valid information from userspace
if cmd != SIOCDEVPRIVATE, other cases the array contains garbage on
the stack. The subsequent switch statement acts on a subcommand in
data[0] which could be any garbage value if cmd is SIOCDEVPRIVATE which
seems incorrect to me. Instead, just return EOPNOTSUPP for the case
where cmd == SIOCDEVPRIVATE to avoid this issue.
As a side note, I suspect that the original intention of the code
was for this ioctl to work just for cmd == SIOCDEVPRIVATE (and the
current logic is reversed). However, I don't wont to change the current
semantics in case any userspace code relies on this existing behaviour.
Detected by CoverityScan, CID#139647 ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f39908d3b1c45 ('net: dsa: mv88e6xxx: Set the CMODE for mv88e6390
ports 9 & 10') added support for setting the CMODE for the 6390X family,
but only enabled it for 9290 and 6390 - and left out 6390X.
Fix support for setting the CMODE on 6390X also by assigning
mv88e6390x_port_set_cmode() to the .port_set_cmode function pointer in
mv88e6390x_ops too.
Fixes: f39908d3b1c4 ("net: dsa: mv88e6xxx: Set the CMODE for mv88e6390 ports 9 & 10")
Signed-off-by: Martin Hundebøll <mnhu@prevas.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unconditional reset dwmac before HW init if reset controller is present.
In existing implementation we reset dwmac only after second module
probing:
(module load -> unload -> load again [reset happens])
Now we reset dwmac at every module load:
(module load [reset happens] -> unload -> load again [reset happens])
Also some reset controllers have only reset callback instead of
assert + deassert callbacks pair, so handle this case.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The global percpu variable ppp_xmit_recursion is used to detect the ppp
xmit recursion to avoid the deadlock, which is caused by one CPU tries to
lock the xmit lock twice. But it would report false recursion when one CPU
wants to send the skb from two different PPP devices, like one L2TP on the
PPPoE. It is a normal case actually.
Now use one percpu member of struct ppp instead of the gloable variable to
detect the xmit recursion of one ppp device.
Fixes: 55454a565836 ("ppp: avoid dealock on recursive xmit")
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: Liu Jianying <jianying.liu@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The caller to the driver marks GFP_NOIO allocations with help
of memalloc_noio-* calls now. This makes redundant to pass down
to the driver gfp flags, which can be GFP_KERNEL only.
The patch removes the gfp flags argument and updates all driver paths.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Since the skb is attached to the first control block of a fragmented
skb it is possible that the skb could be freed when reclaiming that
control block before all fragments of the skb have been consumed by
the hardware and unmapped.
This commit introduces first_cb and last_cb pointers to the skb
control block used by the driver to keep track of which transmit
control blocks within a transmit ring are the first and last ones
associated with the skb.
It then splits the bcmgenet_free_cb() function into transmit
(bcmgenet_free_tx_cb) and receive (bcmgenet_free_rx_cb) versions
that can handle the unmapping of dma mapped memory and cleaning up
the corresponding control block structure so that the skb is only
freed after the last associated transmit control block is reclaimed.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we fail to map a single fragment, we would be leaving the
transmit ring populated with stale entries.
This commit introduces the helper function bcmgenet_put_txcb()
which takes care of rewinding the per-ring write pointer back to
where we left.
It also consolidates the functionality of bcmgenet_xmit_single()
and bcmgenet_xmit_frag() into the bcmgenet_xmit() function to
make the unmapping of control blocks cleaner.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function __mlx4_zone_remove_one_entry always returns zero. So
it is not necessary to check it.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Computing the alignment manually for going from priv to pub is probably
not such a good idea, and in general the assumption that going from priv
to pub is possible trivially could change, so rather than relying on
that, we change things to just store a pointer to pub. This was sugested
by DaveM in [1].
[1] http://www.spinics.net/lists/netdev/msg443992.html
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IDM operations are usually one time ops and should be done in
firmware itself. Driver is not supposed to touch IDM registers.
However, for some SoCs', driver is performing IDM read/writes.
So this patch masks IDM operations in case firmware is taking
care of IDM operations.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Oza Oza <oza.oza@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return type for idm register write callback should be void as 'writel'
API is used for write operation. However, there no need to have 'return'
in this function.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Oza Oza <oza.oza@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull NTB updates from Jon Mason:
"The major change in the series is a rework of the NTB infrastructure
to all for IDT hardware to be supported (and resulting fallout from
that). There are also a few clean-ups, etc.
New IDT NTB driver and changes to the NTB infrastructure to allow for
this different kind of NTB HW, some style fixes (per Greg KH
recommendation), and some ntb_test tweaks"
* tag 'ntb-4.13' of git://github.com/jonmason/ntb:
ntb_netdev: set the net_device's parent
ntb: Add error path/handling to Debug FS entry creation
ntb: Add more debugfs support for ntb_perf testing options
ntb: Remove debug-fs variables from the context structure
ntb: Add a module option to control affinity of DMA channels
NTB: Add IDT 89HPESxNTx PCIe-switches support
ntb_hw_intel: Style fixes: open code macros that just obfuscate code
ntb_hw_amd: Style fixes: open code macros that just obfuscate code
NTB: Add ntb.h comments
NTB: Add PCIe Gen4 link speed
NTB: Add new Memory Windows API documentation
NTB: Add Messaging NTB API
NTB: Alter Scratchpads API to support multi-ports devices
NTB: Alter MW API to support multi-ports devices
NTB: Alter link-state API to support multi-port devices
NTB: Add indexed ports NTB API
NTB: Make link-state API being declared first
NTB: ntb_test: add parameter for doorbell bitmask
NTB: ntb_test: modprobe on remote host
|
|
gcc reports that the temporary buffer for computing the
string length may be too small here:
drivers/net/ethernet/cavium/liquidio/lio_ethtool.c: In function 'lio_get_eeprom_len':
/drivers/net/ethernet/cavium/liquidio/lio_ethtool.c:345:21: error: 'sprintf' may write a terminating nul past the end of the destination [-Werror=format-overflow=]
len = sprintf(buf, "boardname:%s serialnum:%s maj:%lld min:%lld\n",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/cavium/liquidio/lio_ethtool.c:345:6: note: 'sprintf' output between 35 and 167 bytes into a destination of size 128
len = sprintf(buf, "boardname:%s serialnum:%s maj:%lld min:%lld\n",
This extends it to 192 bytes, which is certainly enough. As far
as I could tell, there are no other constraints that require a specific
maximum size.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc-7 notices that "-event-%d" could be more than 11 characters long
if we had larger 'vector' numbers:
drivers/net/vmxnet3/vmxnet3_drv.c: In function 'vmxnet3_activate_dev':
drivers/net/vmxnet3/vmxnet3_drv.c:2095:40: error: 'sprintf' may write a terminating nul past the end of the destination [-Werror=format-overflow=]
sprintf(intr->event_msi_vector_name, "%s-event-%d",
^~~~~~~~~~~~~
drivers/net/vmxnet3/vmxnet3_drv.c:2095:3: note: 'sprintf' output between 9 and 33 bytes into a destination of size 32
The current code is safe, but making the string a little longer
is harmless and lets gcc see that it's ok.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc warns that the temporary buffer might be too small here:
drivers/net/ethernet/cavium/thunder/thunder_bgx.c: In function 'bgx_probe':
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:16: error: '%d' directive writing between 1 and 10 bytes into a region of size between 9 and 11 [-Werror=format-overflow=]
sprintf(str, "BGX%d LMAC%d mode", bgx->bgx_id, lmacid);
^~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:16: note: directive argument in the range [0, 2147483647]
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:3: note: 'sprintf' output between 16 and 27 bytes into a destination of size 20
This probably can't happen, but it can't hurt to make it long
enough for the theoretical limit.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc notices that large queue numbers would overflow the queue name
string:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c: In function 'bnx2x_get_strings':
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:25: error: '%d' directive writing between 1 and 10 bytes into a region of size 5 [-Werror=format-overflow=]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:25: note: directive argument in the range [0, 2147483647]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:5: note: 'sprintf' output between 2 and 11 bytes into a destination of size 5
There is a hard limit in place that makes the number at most two
digits, so the code is fine. This changes it to use snprintf()
to truncate instead of overflowing, which shuts up that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We get a warning for the port_name string that might be longer than
six characters if we had more than 10 ports:
drivers/net/ethernet/sun/niu.c: In function 'niu_put_parent':
drivers/net/ethernet/sun/niu.c:9563:21: error: '%d' directive writing between 1 and 3 bytes into a region of size 2 [-Werror=format-overflow=]
sprintf(port_name, "port%d", port);
^~~~~~~~
drivers/net/ethernet/sun/niu.c:9563:21: note: directive argument in the range [0, 255]
drivers/net/ethernet/sun/niu.c:9563:2: note: 'sprintf' output between 6 and 8 bytes into a destination of size 6
sprintf(port_name, "port%d", port);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/sun/niu.c: In function 'niu_pci_init_one':
drivers/net/ethernet/sun/niu.c:9538:22: error: '%d' directive writing between 1 and 3 bytes into a region of size 2 [-Werror=format-overflow=]
sprintf(port_name, "port%d", port);
^~~~~~~~
drivers/net/ethernet/sun/niu.c:9538:22: note: directive argument in the range [0, 255]
drivers/net/ethernet/sun/niu.c:9538:3: note: 'sprintf' output between 6 and 8 bytes into a destination of size 6
While we know that the port number is small, there is no harm in
making the format string two bytes longer to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the interface is not up, then don't try to close it during a
shutdown. This avoids possible double free of the IRQ, which
can happen during a shutdown.
Fixes: 03eb3eb4d4d5 ("net: qcom/emac: add shutdown function")
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change enables the use of SW timestamping on Raspberry PI.
smsc95xx uses the usbnet transmit function usbnet_start_xmit(), which
implements software timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE
capability was missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced.
By using ethtool_op_get_ts_info() as get_ts_info() also the
SOF_TIMESTAMPING_TX_SOFTWARE is announced.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check ptp_clock_register() return not only for NULL but
also for error pointers, and also nullify adapter->ptp_clock
if ptp_clock_register() fails.
Fixes: 9c33e4208bce ("cxgb4: Add PTP Hardware Clock (PHC) support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code only support DT method to control xge led.
This patch is the implementation of acpi method to control xge led.
Signed-off-by: LiuJian <liujian56@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some firmwares in Huawei E3372H devices have been observed to switch back
to NTB 32-bit format after altsetting switch.
This patch implements a driver flag to check for the device settings and
set NTB format to 16-bit again if needed.
The flag has been activated for devices controlled by the huawei_cdc_ncm.c
driver.
V1->V2:
- fixed broken error checks
- some corrections to the commit message
V2->V3:
- variable name changes, to clarify what's happening
- check (and possibly set) the NTB format later in the common bind code path
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-and-tested-by: Christian Panton <christian@panton.org>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
CC: Bjørn Mork <bjorn@mork.no>
CC: Christian Panton <christian@panton.org>
CC: linux-usb@vger.kernel.org
CC: netdev@vger.kernel.org
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mdio_mux_init parses the child nodes of the MDIO mux. When using
"mdio-mux-mmioreg" the child nodes are describing the register value
that is written to switch between the MDIO busses.
The change which makes the error messages more verbose changed the
parsing of the "reg" property from a simple of_property_read_u32 call
to of_mdio_parse_addr. On a Khadas VIM (based on the Meson GXL SoC,
which uses mdio-mux-mmioreg) this prevents registering the MDIO mux
(because the "reg" values on the MDIO mux child nodes are 0x2009087f
and 0xe40908ff) and leads to the following errors:
mdio-mux-mmioreg c883455c.eth-phy-mux: /soc/periphs@c8834000/eth-phy-mux/mdio@e40908ff PHY address -469169921 is too large
mdio-mux-mmioreg c883455c.eth-phy-mux: Error: Failed to find reg for child /soc/periphs@c8834000/eth-phy-mux/mdio@e40908ff
mdio-mux-mmioreg c883455c.eth-phy-mux: /soc/periphs@c8834000/eth-phy-mux/mdio@2009087f PHY address 537462911 is too large
mdio-mux-mmioreg c883455c.eth-phy-mux: Error: Failed to find reg for child /soc/periphs@c8834000/eth-phy-mux/mdio@2009087f
mdio-mux-mmioreg c883455c.eth-phy-mux: Error: No acceptable child buses found
mdio-mux-mmioreg c883455c.eth-phy-mux: failed to register mdio-mux bus /soc/periphs@c8834000/eth-phy-mux
(as a result of that ethernet is not working, because the PHY which is
connected through the mux' child MDIO bus, which is not being
registered).
Fix this by reverting the change from of_mdio_parse_addr to
of_mdio_parse_addr.
Fixes: 342fa1964439 ("mdio: mux: make child bus walking more permissive and errors more verbose")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add 0x50a3 and 0x50a4 T5 device id's
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't populate array glrt_table on the stack but make it static.
Makes the object code a smaller by over 670 bytes:
Before:
text data bss dec hex filename
131772 4733 0 136505 21539 rt2800lib.o
After:
text data bss dec hex filename
131043 4789 0 135832 21298 rt2800lib.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't populate array route_possibilities on the stack but make it
static const. Makes the object code a little smaller by 85 bytes:
Before:
text data bss dec hex filename
9901 2448 0 12349 303d dwmac4_core.o
After:
text data bss dec hex filename
9760 2504 0 12264 2fe8 dwmac4_core.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't populate various tables on the stack but make them static const.
Makes the object code smaller by nearly 200 bytes:
Before:
text data bss dec hex filename
113468 11200 0 124668 1e6fc bnx2x_ethtool.o
After:
text data bss dec hex filename
113129 11344 0 124473 1e639 bnx2x_ethtool.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change fixes following problem
[ 1.827940] xgene-enet: probe of 1f210030.ethernet failed with error -2
which leads to a missing ethernet interface (reproducable at least on
Gigabyte MP30-AR0 and APM Mustang systems).
The check for a valid clk resource fails, because DT doesn't provide a
clock for sgenet1. But the driver doesn't use this clk, if the ethernet
port is connected via SGMII. Therefore this patch avoids probing for clk
on SGMII interfaces.
Fixes: 9aea7779b764 ("drivers: net: xgene: Fix crash on DT systems")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since internal phy-mode is reserved for non-xMII protocol we cannot use
it with dwmac-sun8i.
Furthermore, all DT patchs which comes with this patch were cleaned, so
the current state is broken.
This reverts commit 1c2fa5f84683 ("net: stmmac: support future possible different internal phy mode")
Fixes: 1c2fa5f84683 ("net: stmmac: support future possible different internal phy mode")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we have more than 32 unicast MAC addresses assigned to an interface
we will read beyond the end of the address table in the driver when
adding filters. The next 256 entries store multicast addresses, so we
will end up attempting to insert duplicate filters, which is mostly
harmless. If we add more than 288 unicast addresses we will then read
past the multicast address table, which is likely to be more exciting.
Fixes: 12fb0da45c9a ("sfc: clean fallbacks between promisc/normal in efx_ef10_filter_sync_rx_mode")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no check for return code of smsc911x_drv_probe()
in smsc911x_drv_probe(). The patch adds one.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
