| Age | Commit message (Collapse) | Author |
|---|
|
This register configures global NVE configuration such as source IP of
the NVE tunnel and UDP source port calculation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the seed of the LAG hash function is always set to 0, which
means it is identical across all switches. Instead, use a random number.
This is especially important now that VxLAN is supported, as the LAG
hash function is used to calculate the UDP source port of the
encapsulated packet.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device has the ability to flush all the FDB records that perform NVE
encapsulation or only a subset of these with a specific filtering
identifier (FID).
Expose these types so that they could be used by subsequent patches
where we need to flush the FDB records when an NVE device is unlinked
from a bridge (FID).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the device needs to flood an overlay packet to remote VTEPs it
retrieves a pointer to the head of a linked-list of records that store
the IP addresses of these VTEPs.
These records are stored in the KVD linear memory and configured via the
Tunneling NVE Underlay Multicast Table (TNUMT) register.
Add a new KVD linear entry type for these records, so that we will be
able to allocate and free them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The L3 protocol and address definitions are going to be used by the NVE
code, so move them to the global header file from the one private to the
router.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VxLAN notifications are going to use a different notifier information
type, so cast to the correct type based on the received event.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VxLAN FDB updates are sent with the VxLAN device which is not our upper
and will therefore be ignored by current code.
Solve this by checking whether the upper device (bridge) is our upper.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VxLAN FDB notifications need to be handled differently than bridge FDB
notifications, so initialize the work item based on the received
notification and rename the invoked function accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The spectrum_router.h header file is private to the router block and
should only be included by direct consumers of it, such as dpipe and the
multicast routing code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/marvell/octeontx2/af/cgx.c: In function 'cgx_fwi_event_handler':
drivers/net/ethernet/marvell/octeontx2/af/cgx.c:257:17: warning:
variable 'dev' set but not used [-Wunused-but-set-variable]
It never be used since introduction in
commit 1463f382f58d ("octeontx2-af: Add support for CGX link management")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the NETIF_F_RXFCS feature in the Mscc
Ethernet driver. This feature is disabled by default and allow a user
to request the driver not to drop the FCS and to extract it into the skb
for debugging purposes.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds RSS tuple support for VF in revision
0x21.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds RSS key, hash algorithm configuration support
for VF in revision 0x21.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds ETH_RSS_HASH_XOR hash algorithm supports, which
is supported by hw revision 0x21.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added support for Gemalto's Cinterion ALASxx WWAN interfaces
by adding QMI_FIXED_INTF with Cinterion's VID and PID.
Signed-off-by: Giacinto Cifelli <gciofono@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.
Fixes: 8cfa94984c9c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.
Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.
Fixes: d9338023fb8e ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because the function __skb_get_hash_symmetric always returns non-zero.
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Wang Li <wangli39@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ethtool .set_coalesce (-C) and .get_coalesce (-c) handlers.
Interrupt moderation is currently not supported, so these accept and
display the default settings of 0 usec and 1 frame.
Toggle tx napi through setting tx-frames. So as to not interfere
with possible future interrupt moderation, value 1 means tx napi while
value 0 means not.
Only allow the switching when device is down for simplicity.
Link: https://patchwork.ozlabs.org/patch/948149/
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Read the host context count symbols provided by firmware and use
it to determine the number of allocated stats ids. Previously it
won't be possible to offload more than 2^17 filter even if FW was
able to do so.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of an array stats instead of storing stats per flow which
would require a hash lookup at critical times.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of relativistic hash tables for tracking flows instead
of fixed sized hash tables.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several variables being initialized that are being set later
and hence the initialization is redundant and can be removed. Remove
then.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added support in RVU AF driver to register for
CGX LMAC link status change events from firmware
and managing them. Processing part will be added
in followup patches.
- Introduced eventqueue for posting events from cgx lmac.
Queueing mechanism will ensure that events can be posted
and firmware can be acked immediately and hence event
reception and processing are decoupled.
- Events gets added to the queue by notification callback.
Notification callback is expected to be atomic, since it
is called from interrupt context.
- Events are dequeued and processed in a worker thread.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CGX LMAC initialization, link status polling etc is done
by low level secure firmware. For link management this patch
adds a interface or communication mechanism between firmware
and this kernel CGX driver.
- Firmware interface specification is defined in cgx_fw_if.h.
- Support to send/receive commands/events to/form firmware.
- events/commands implemented
* link up
* link down
* reading firmware version
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Nithya Mani <nmani@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each of the enabled CGX LMAC is considered a physical
interface and RVU PFs are mapped to these. VFs of these
SRIOV PFs will be virtual interfaces and share CGX LMAC
along with PF.
This mapping info will be used later on for Rx/Tx pkt steering.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds basic template for Marvell OcteonTX2's
CGX ethernet interface driver. Just the probe.
RVU AF driver will use APIs exported by this driver
for various things like PF to physical interface mapping,
loopback mode, interface stats etc. Hence marged both
drivers into a single module.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW interprets RVU_AF_MSIXTR_BASE address as an IOVA, hence
create a IOMMU mapping for the physcial address configured by
firmware and reconfig RVU_AF_MSIXTR_BASE with IOVA.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware configures a certain number of MSIX vectors to each of
enabled RVU PF/VF. When a block LF is attached to a PF/VF, number
of MSIX vectors needed by that LF are set aside (out of PF/VF's
total MSIX vectors) and LF's msix_offset is configured in HW.
Also added support for a RVU PF/VF to retrieve that block LF's
MSIX vector offset information from AF via mbox.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added support for a RVU PF/VF to request AF via mailbox
to attach or detach NPA/NIX/SSO/SSOW/TIM/CPT block LFs.
Also supports partial detachment and modifying current
LF attached count of a certian block type.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Scan all RVU blocks to find any 'LF to RVU PF/VF' mapping done by
low level firmware. If found any, mark them as used in respective
block's LF bitmap and also save mapped PF/VF's PF_FUNC info.
This is done to avoid reattaching a block LF to a different RVU PF/VF.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With 10's of mailbox messages expected to be handled in future,
checking for message id could become a lengthy switch case. Hence
added a macro to auto generate the switch case for each msg id.
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for mailbox interrupt and message
handling. Mapped mailbox region and registered a workqueue
for message handling. Enabled mailbox IRQ of RVU PFs
and registered a interrupt handler. When IRQ is triggered
work is added to the mbox workqueue for msgs to get processed.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds mailbox support infrastructure APIs.
Each RVU device has a dedicated 64KB mailbox region
shared with it's peer for communication. RVU AF has
a separate mailbox region shared with each of RVU PFs
and a RVU PF has a separate region shared with each of
it's VF.
These set of APIs are used by this driver (RVU AF) and
other RVU PF/VF drivers eg netdev, crypto e.t.c.
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Lukasz Bartosik <lbartosik@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch gathers NPA/NIX/SSO/SSOW/TIM/CPT RVU blocks's
HW info like number of LFs. Important register offsets
saved for later use to avoid code duplication for each block.
A bitmap is allocated for each of the blocks which later
on will be used to allocate a LF for a RVU PF/VF.
Also added RVU NIX/NPA block registers and few registers
of other blocks.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Go through all BLKADDRs and check which ones are implemented
on this silicon and do a HW reset of each implemented block.
Also added all RVU AF and PF register offsets.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds basic template for Marvell OcteonTX2's
resource virtualization unit (RVU) admin function (AF)
driver. Just the driver registration and probe.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently driver registers to physical link notifications (of the device)
from Management firmware (MFW). Driver doesn't get notified if there's a
change in the virtual link e.g., link-flap on the peer PF interface.
Virtual link indication from MFW reflects the per PF link status instead
of the physical link.
The patch adds driver support for,
- Advertising the virtual link support to MFW.
- Handling the virtual link notification from MFW.
Please consider applying it to 'net-next'.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When powering down a SDIO connected card during suspend, make sure to call
into the generic lbs_suspend() function before pulling the plug. This will
make sure the card is successfully deregistered from the system to avoid
communication to the card starving out.
Fixes: 7444a8092906 ("libertas: fix suspend and resume for SDIO connected cards")
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add thermal zone support to monitor ASIC's temperature.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When memory is limited (on kdump kernel), reduce size of rx and tx rings.
Also reduce the number of rx rings.
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eliminate potential auto casting compilation error.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
napi poll functions should be initialized before running request_irq(),
to handle a rare condition where there is a pending interrupt, causing
the ISR to fire immediately while the poll function wasn't set yet,
causing a NULL dereference.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a rare scenario when ena_device_restore() fails, followed by device
remove, an FLR will not be issued. In this case, the device will keep
sending asynchronous AENQ keep-alive events, even after driver removal,
leading to memory corruption.
Fixes: 8c5c7abdeb2d ("net: ena: add power management ops to the ENA driver")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Memory mapped with devm_ioremap is automatically freed when the driver
is disconnected from the device. Therefore there is no need to
explicitly call devm_iounmap.
Fixes: 0857d92f71b6 ("net: ena: add missing unmap bars on device removal")
Fixes: 411838e7b41c ("net: ena: fix rare kernel crash when bar memory remap fails")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-10-08
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) sk_lookup_[tcp|udp] and sk_release helpers from Joe Stringer which allow
BPF programs to perform lookups for sockets in a network namespace. This would
allow programs to determine early on in processing whether the stack is
expecting to receive the packet, and perform some action (eg drop,
forward somewhere) based on this information.
2) per-cpu cgroup local storage from Roman Gushchin.
Per-cpu cgroup local storage is very similar to simple cgroup storage
except all the data is per-cpu. The main goal of per-cpu variant is to
implement super fast counters (e.g. packet counters), which don't require
neither lookups, neither atomic operations in a fast path.
The example of these hybrid counters is in selftests/bpf/netcnt_prog.c
3) allow HW offload of programs with BPF-to-BPF function calls from Quentin Monnet
4) support more than 64-byte key/value in HW offloaded BPF maps from Jakub Kicinski
5) rename of libbpf interfaces from Andrey Ignatov.
libbpf is maturing as a library and should follow good practices in
library design and implementation to play well with other libraries.
This patch set brings consistent naming convention to global symbols.
6) relicense libbpf as LGPL-2.1 OR BSD-2-Clause from Alexei Starovoitov
to let Apache2 projects use libbpf
7) various AF_XDP fixes from Björn and Magnus
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, both Rx and Tx confirmation frames handled during
NAPI poll were counted toward the NAPI budget. However, Tx
confirmations are lighter to process than Rx frames, which can
skew the amount of work actually done inside one NAPI cycle.
Update the code to only count Rx frames toward the NAPI budget
and set a separate threshold on how many Tx conf frames can be
processed in one poll cycle.
The NAPI poll routine stops when either the budget is consumed
by Rx frames or when Tx confirmation frames reach this threshold.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mscc/ocelot_board.c: In function 'mscc_ocelot_probe':
drivers/net/ethernet/mscc/ocelot_board.c:262:17: warning:
variable 'phy_mode' set but not used [-Wunused-but-set-variable]
enum phy_mode phy_mode;
It never used since introduction in
commit 71e32a20cfbf ("net: mscc: ocelot: make use of SerDes PHYs for handling their configuration")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
