| Age | Commit message (Collapse) | Author |
|---|
|
Do camera capture test on i.MX6q sabresd board, and save the capture data to
nfs rootfs. The command is:
gst-launch-1.0 -e imxv4l2src device=/dev/video1 num-buffers=2592000 ! tee name=t !
queue ! imxv4l2sink sync=false t. ! queue ! vpuenc ! queue ! mux. pulsesrc num-buffers=3720937
blocksize=4096 ! 'audio/x-raw, rate=44100, channels=2' ! queue ! imxmp3enc ! mpegaudioparse !
queue ! mux. qtmux name=mux ! filesink location=video_recording_long.mov
After about 10 hours running, there have net watchdog timeout kernel dump:
...
WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:264 dev_watchdog+0x2b4/0x2d8()
NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.24-01051-gdb840b7 #440
[<80014e6c>] (unwind_backtrace) from [<800118ac>] (show_stack+0x10/0x14)
[<800118ac>] (show_stack) from [<806ae3f0>] (dump_stack+0x78/0xc0)
[<806ae3f0>] (dump_stack) from [<8002b504>] (warn_slowpath_common+0x68/0x8c)
[<8002b504>] (warn_slowpath_common) from [<8002b558>] (warn_slowpath_fmt+0x30/0x40)
[<8002b558>] (warn_slowpath_fmt) from [<8055e0d4>] (dev_watchdog+0x2b4/0x2d8)
[<8055e0d4>] (dev_watchdog) from [<800352d8>] (call_timer_fn.isra.33+0x24/0x8c)
[<800352d8>] (call_timer_fn.isra.33) from [<800354c4>] (run_timer_softirq+0x184/0x220)
[<800354c4>] (run_timer_softirq) from [<8002f420>] (__do_softirq+0xc0/0x22c)
[<8002f420>] (__do_softirq) from [<8002f804>] (irq_exit+0xa8/0xf4)
[<8002f804>] (irq_exit) from [<8000ee5c>] (handle_IRQ+0x54/0xb4)
[<8000ee5c>] (handle_IRQ) from [<80008598>] (gic_handle_irq+0x28/0x5c)
[<80008598>] (gic_handle_irq) from [<800123c0>] (__irq_svc+0x40/0x74)
Exception stack(0x80d27f18 to 0x80d27f60)
7f00: 80d27f60 0000014c
7f20: 8858c60e 0000004d 884e4540 0000004d ab7250d0 80d34348 00000000 00000000
7f40: 00000001 00000000 00000017 80d27f60 800702a4 80476e6c 600f0013 ffffffff
[<800123c0>] (__irq_svc) from [<80476e6c>] (cpuidle_enter_state+0x50/0xe0)
[<80476e6c>] (cpuidle_enter_state) from [<80476fa8>] (cpuidle_idle_call+0xac/0x154)
[<80476fa8>] (cpuidle_idle_call) from [<8000f174>] (arch_cpu_idle+0x8/0x44)
[<8000f174>] (arch_cpu_idle) from [<80064c54>] (cpu_startup_entry+0x100/0x158)
[<80064c54>] (cpu_startup_entry) from [<80cd8a9c>] (start_kernel+0x304/0x368)
---[ end trace 09ebd32fb032f86d ]---
...
There might have a race in napi_schedule(), leaving interrupts disabled forever.
After these patch, the case still work more than 40 hours running.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After d75b1ade567ffab085e8adbbdacf0092d10cd09c (net: less interrupt
masking in NAPI) the napi instance is removed from the per-cpu list
prior to calling the n->poll(), and is only requeued if all of the
budget was used. This inadvertently broke netfront because netfront
does not use NAPI correctly.
If netfront had not used all of its budget it would do a final check
for any Rx responses and avoid calling napi_complete() if there were
more responses. It would still return under budget so it would never
be rescheduled. The final check would also not re-enable the Rx
interrupt.
Additionally, xenvif_poll() would also call napi_complete() /after/
enabling the interrupt. This resulted in a race between the
napi_complete() and the napi_schedule() in the interrupt handler. The
use of local_irq_save/restore() avoided by race iff the handler is
running on the same CPU but not if it was running on a different CPU.
Fix both of these by always calling napi_compete() if the budget was
not all used, and then calling napi_schedule() if the final checks
says there's more work.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-12-16
Please pull this batch of fixes intended for the 3.19 stream!
For the Bluetooth bits, Johan says:
"The patches consist of:
- Coccinelle warning fix
- hci_dev_lock/unlock fixes
- Fixes for pending mgmt command handling
- Fixes for properly following the force_lesc_support switch
- Fix for a Microsoft branded Broadcom adapter
- New device id for Atheros AR3012
- Fix for BR/EDR Secure Connections enabling"
Along with that...
Brian Norris avoids leaking some kernel memory contents via printk in brcmsmac.
Julia Lawall corrects some misspellings in a few drivers.
Larry Finger gives us one more rtlwifi fix to correct a porting oversight.
Wei Yongjun fixes a sparse warning in rtlwifi.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise we get things like:
warning: (NET_DSA_BCM_SF2 && BCMGENET && SYSTEMPORT) selects FIXED_PHY which has unmet direct dependencies (NETDEVICES && PHYLIB=y)
In order to make this work we have to rename fixed.c to fixed_phy.c
because the regulator drivers already have a module named "fixed.o".
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use TUNSETVNETLE/TUNGETVNETLE instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use TUNSETVNETLE/TUNGETVNETLE instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
flags field in ifreq is only 16 bit wide, but
we read it as a 32 bit value.
If userspace doesn't zero-initialize unused fields,
this will lead to failures.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to do the following:
select FIXED_PHY if NET_DSA_BCM_SF2=y, as this implies that we will not be
able to build and/or run the driver correctly when built as a module,
which is no longer an issue since commit 37e9a6904520 ("net: phy: export
fixed_phy_register()").
Fixes: 246d7f773c13ca ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to do the following:
select FIXED_PHY if SYSTEMPORT=y, as this implies that we will not be able
to build and/or run the driver correctly when built as a module, which
is no longer an issue since commit 37e9a6904520 ("net: phy: export
fixed_phy_register()")
Fixes: a3862db2d3c4 ("net: systemport: hook SYSTEMPORT driver in the build")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to do the following:
select FIXED_PHY if BCMGENET=y, as this implies that we will not be able
to build and/or run the driver correctly when built as a module, which
is no longer an issue since commit 37e9a6904520 ("net: phy: export
fixed_phy_register()")
Fixes: b0ba512e225d ("net: bcmgenet: enable driver to work without device tree"
Fixes: bdaa53bde55f ("net: bcmgenet: hook into the build system")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The setting of this flag was missed in previous modifications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Debug code prints the fifo name via custom dev_warn() wrappers. The
fifo_names array is only non-zero when debugging is manually enabled,
which is all well and good. However, it's *not* good that this array
uses zero-length arrays in the non-debug case, and so it doesn't
actually have any memory allocated to it. This means that as far as we
know, fifo_names[i] actually points to garbage memory.
I've seen this in my log:
[ 4601.205511] brcmsmac bcma0:1: wl0: brcms_c_d11hdrs_mac80211: �GeL txop exceeded phylen 137/256 dur 1602/1504
So let's give this array space enough to fill it with a NULL byte.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list@broadcom.com
Cc: netdev@vger.kernel.org
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fixes the following sparse warning:
drivers/net/wireless/rtlwifi/rtl8192cu/hw.c:1595:6: warning:
symbol 'usb_cmd_send_packet' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Replace a misspelled function name by %s and then __func__.
8821 was written as 8812.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Replace a misspelled function name by %s and then __func__.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Replace a misspelled function name by %s and then __func__.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Inside macb_probe(), when devm_request_irq() fails on queue q, there is no need
to call devm_free_irq() on queues 0..q-1 because the managed device resources
are released later when calling free_netdev().
Also removing devm_free_irq() call from macb_remove() for the same reason.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix a bug introduced by the multiqueue support patch:
"net/macb: add TX multiqueue support for gem"
the "bp" pointer to the netdev private data was dereferenced and used after the
associated memory had been freed by calling free_netdev().
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If CONFIG_OF is not set:
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c: In function ‘sti_dwmac_parse_data’:
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c:318: warning: ‘rs’ is used uninitialized in this function
of_property_read_string() will return -ENOSYS in this case, and rs will
be an uninitialized pointer.
While the fallback clock selection is already selected correctly in this
case, the string comparisons should be skipped too, else the system will
crash while dereferencing the uninitialized pointer.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If GPIOLIB=n the following build errors occur:
drivers/net/ethernet/smsc/smc91x.c: In function 'try_toggle_control_gpio':
drivers/net/ethernet/smsc/smc91x.c:2204:2: error: implicit declaration of function 'devm_gpiod_get_index' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2204:7: warning: assignment makes pointer from integer without a cast [enabled by default]
drivers/net/ethernet/smsc/smc91x.c:2213:2: error: implicit declaration of function 'gpiod_direction_output' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2216:3: error: implicit declaration of function 'devm_gpiod_put' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2222:2: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
Fix this by letting the driver depend on GPIOLIB if OF is selected.
Fixes: 7d2911c4381 ("net: smc91x: Fix gpios for device tree based booting")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To be future-proof and for better readability the time comparisons are
modified to use time_before, time_after, and time_after_eq instead of
plain, error-prone math.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To support asymmetric EQ allocations, we should query the device
capabilities prior to enabling SRIOV. As a side effect of adding that,
we are dumping the PF device capabilities twice. Avoid that by moving
the printing into a helper function which is called once.
Fixes: 7ae0e400cd93 ('net/mlx4_core: Flexible (asymmetric) allocation of
EQs and MSI-X vectors for PF/VFs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current mlx4_load_one has a memory leak as it always allocates
dev_cap, but frees it only on error.
In addition, even if VFs exist when mlx4_load_one is called,
we still need to notify probed VFs that we're loading (by
incrementing pf_loading).
Fixes: a0eacca948d2 ('net/mlx4_core: Refactor mlx4_load_one')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
|
|
Pull another networking update from David Miller:
"Small follow-up to the main merge pull from the other day:
1) Alexander Duyck's DMA memory barrier patch set.
2) cxgb4 driver fixes from Karen Xie.
3) Add missing export of fixed_phy_register() to modules, from Mark
Salter.
4) DSA bug fixes from Florian Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (24 commits)
net/macb: add TX multiqueue support for gem
linux/interrupt.h: remove the definition of unused tasklet_hi_enable
jme: replace calls to redundant function
net: ethernet: davicom: Allow to select DM9000 for nios2
net: ethernet: smsc: Allow to select SMC91X for nios2
cxgb4: Add support for QSA modules
libcxgbi: fix freeing skb prematurely
cxgb4i: use set_wr_txq() to set tx queues
cxgb4i: handle non-pdu-aligned rx data
cxgb4i: additional types of negative advice
cxgb4/cxgb4i: set the max. pdu length in firmware
cxgb4i: fix credit check for tx_data_wr
cxgb4i: fix tx immediate data credit check
net: phy: export fixed_phy_register()
fib_trie: Fix trie balancing issue if new node pushes down existing node
vlan: Add ability to always enable TSO/UFO
r8169:update rtl8168g pcie ephy parameter
net: dsa: bcm_sf2: force link for all fixed PHY devices
fm10k/igb/ixgbe: Use dma_rmb on Rx descriptor reads
r8169: Use dma_rmb() and dma_wmb() for DescOwn checks
...
|
|
Pull sparc update from David Miller:
"Not a lot of stuff this time around, mostly bug fixing:
- Fix alignment of 32-bit crosscall datastructure on Leon, from
Andreas Larsson.
- Several fixes to the virtual disk driver on sparc64 by Dwight
Engen, including handling resets of the service domain properly"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sunvdc: reconnect ldc after vds service domain restarts
sparc/ldc: create separate ldc_unbind from ldc_free
vio: create routines for inc,dec vio dring indexes
sunvdc: fix module unload/reload
sparc32, leon: Align ccall_info to prevent unaligned traps on crosscall
|
|
gem devices designed with multiqueue CANNOT work without this patch.
When probing a gem device, the driver must first prepare and enable the
peripheral clock before accessing I/O registers. The second step is to read the
MID register to find whether the device is a gem or an old macb IP.
For gem devices, it reads the Design Configuration Register 6 (DCFG6) to
compute to total number of queues, whereas macb devices always have a single
queue.
Only then it can call alloc_etherdev_mq() with the correct number of queues.
This is the reason why the order of some initializations has been changed in
macb_probe().
Eventually, the dedicated IRQ and TX ring buffer descriptors are initialized
for each queue.
For backward compatibility reasons, queue0 uses the legacy registers ISR, IER,
IDR, IMR, TBQP and RBQP. On the other hand, the other queues use new registers
ISR[1..7], IER[1..7], IDR[1..7], IMR[1..7], TBQP[1..7] and RBQP[1..7].
Except this hardware detail there is no real difference between queue0 and the
others. The driver hides that thanks to the struct macb_queue.
This structure allows us to share a common set of functions for all the queues.
Besides when a TX error occurs, the gem MUST be halted before writing any of
the TBQP registers to reset the relevant queue. An immediate side effect is
that the other queues too aren't processed anymore by the gem.
So macb_tx_error_task() calls netif_tx_stop_all_queues() to notify the Linux
network engine that all transmissions are stopped.
Also macb_tx_error_task() now calls spin_lock_irqsave() to prevent the
interrupt handlers of the other queues from running as each of them may wake
its associated queue up (please refer to macb_tx_interrupt()).
Finally, as all queues have previously been stopped, they should be restarted
calling netif_tx_start_all_queues() and setting the TSTART bit into the Network
Control Register. Before this patch, when dealing with a single queue, the
driver used to defer the reset of the faulting queue and the write of the
TSTART bit until the next call of macb_start_xmit().
As explained before, this bit is now set by macb_tx_error_task() too. That's
why the faulting queue MUST be reset by setting the TX_USED bit in its first
buffer descriptor before writing the TSTART bit.
Queue 0 always exits and is the lowest priority when other queues are available.
The higher the index of the queue is, the higher its priority is.
When transmitting frames, the TX queue is selected by the skb->queue_mapping
value. So queue discipline can be used to define the queue priority policy.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calls to tasklet_hi_enable are replaced by calls to
tasklet_enable since the 2 functions are redundant.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree update from Jiri Kosina:
"Usual stuff: documentation updates, printk() fixes, etc"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
intel_ips: fix a type in error message
cpufreq: cpufreq-dt: Move newline to end of error message
ps3rom: fix error return code
treewide: fix typo in printk and Kconfig
ARM: dts: bcm63138: change "interupts" to "interrupts"
Replace mentions of "list_struct" to "list_head"
kernel: trace: fix printk message
scsi: mpt2sas: fix ioctl in comment
zbud, zswap: change module author email
clocksource: Fix 'clcoksource' typo in comment
arm: fix wording of "Crotex" in CONFIG_ARCH_EXYNOS3 help
gpio: msm-v1: make boolean argument more obvious
usb: Fix typo in usb-serial-simple.c
PCI: Fix comment typo 'COMFIG_PM_OPS'
powerpc: Fix comment typo 'CONIFG_8xx'
powerpc: Fix comment typos 'CONFiG_ALTIVEC'
clk: st: Spelling s/stucture/structure/
isci: Spelling s/stucture/structure/
usb: gadget: zero: Spelling s/infrastucture/infrastructure/
treewide: Fix company name in module descriptions
...
|
|
This chip is present on older revisions of the DE2 development kit.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This chip is present on the Nios2 Development Kit 2C35.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware 1.12.25.0 added support for QSA module, adding the driver code for it.
Also fixes some ethtool get settings for other module types.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Programs the firmware of the maximum outgoing iscsi pdu length per connection.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When building the bcmgenet driver as module, I get:
ERROR: "fixed_phy_register" [drivers/net/ethernet/broadcom/genet/genet.ko] undefined!
commit b0ba512e225d72 ("net: bcmgenet: enable driver to work without device
tree") which added a call to fixed_phy_register. But fixed_phy_register
needs to be exported if used from a module.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both sunvdc and sunvnet implemented distinct functionality for incrementing
and decrementing dring indexes. Create common functions for use by both
from the sunvnet versions, which were chosen since they will still work
correctly in case a non power of two ring size is used.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ephy parameter to rtl8168g.
Also change the common function of rtl8168g from "rtl_hw_start_8168g_1" to
"rtl_hw_start_8168g". And function "rtl_hw_start_8168g_1" is used for
setting rtl8168g hardware parameters.
Following is the explanation of what hardware parameter change for.
rtl8168g may erroneous judge the PCIe signal quality and show the error bit
on PCI configuration space when in PCIe low power mode.
The following ephy parameters are for above issue.
{ 0x00, 0x0000, 0x0008 }
{ 0x0c, 0x37d0, 0x0820 }
{ 0x1e, 0x0000, 0x0001 }
rtl8168g may return to PCIe L0 from PCIe L0s low power mode too slow.
The following ephy parameter is for above issue.
{ 0x19, 0x8000, 0x0000 }
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For ports of the switch that we define as "fixed PHYs" such as MoCA, we
would have our Port 7 special handling that would allow us to assert the
link status indication.
For other ports, such as e.g: RGMII_1 connected to a cable modem, we
would rely on whatever the bootloader has left configured, which is a
bad assumption to make, we really need to force the link status
indication here.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change makes it so that dma_rmb is used when reading the Rx
descriptor. The advantage of dma_rmb is that it allows for a much
lower cost barrier on x86, powerpc, arm, and arm64 architectures than a
traditional memory barrier when dealing with reads that only have to
synchronize to coherent memory.
In addition I have updated the code so that it just checks to see if any
bits have been set instead of just the DD bit since the DD bit will always
be set as a part of a descriptor write-back so we just need to check for a
non-zero value being present at that memory location rather than just
checking for any specific bit. This allows the code itself to appear much
cleaner and allows the compiler more room to optimize.
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The r8169 use a pair of wmb() calls when setting up the descriptor rings.
The first is to synchronize the descriptor data with the descriptor status,
and the second is to synchronize the descriptor status with the use of the
MMIO doorbell to notify the device that descriptors are ready. This can
come at a heavy price on some systems, and is not really necessary on
systems such as x86 as a simple barrier() would suffice to order store/store
accesses. As such we can replace the first memory barrier with
dma_wmb() to reduce the cost for these accesses.
In addition the r8169 uses a rmb() to prevent compiler optimization in the
cleanup paths, however by moving the barrier down a few lines and replacing
it with a dma_rmb() we should be able to use it to guarantee
descriptor accesses do not occur until the device has updated the DescOwn
bit from its end.
One last change I made is to move the update of cur_tx in the xmit path to
after the wmb. This way we can guarantee the device and all CPUs should
see the DescOwn update before they see the cur_tx value update.
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull MIPS updates from Ralf Baechle:
"This is an unusually large pull request for MIPS - in parts because
lots of patches missed the 3.18 deadline but primarily because some
folks opened the flood gates.
- Retire the MIPS-specific phys_t with the generic phys_addr_t.
- Improvments for the backtrace code used by oprofile.
- Better backtraces on SMP systems.
- Cleanups for the Octeon platform code.
- Cleanups and fixes for the Loongson platform code.
- Cleanups and fixes to the firmware library.
- Switch ATH79 platform to use the firmware library.
- Grand overhault to the SEAD3 and Malta interrupt code.
- Move the GIC interrupt code to drivers/irqchip
- Lots of GIC cleanups and updates to the GIC code to use modern IRQ
infrastructures and features of the kernel.
- OF documentation updates for the GIC bindings
- Move GIC clocksource driver to drivers/clocksource
- Merge GIC clocksource driver with clockevent driver.
- Further updates to bring the GIC clocksource driver up to date.
- R3000 TLB code cleanups
- Improvments to the Loongson 3 platform code.
- Convert pr_warning to pr_warn.
- Merge a bunch of small lantiq and ralink fixes that have been
staged/lingering inside the openwrt tree for a while.
- Update archhelp for IP22/IP32
- Fix a number of issues for Loongson 1B.
- New clocksource and clockevent driver for Loongson 1B.
- Further work on clk handling for Loongson 1B.
- Platform work for Broadcom BMIPS.
- Error handling cleanups for TurboChannel.
- Fixes and optimization to the microMIPS support.
- Option to disable the FTLB.
- Dump more relevant information on machine check exception
- Change binfmt to allow arch to examine PT_*PROC headers
- Support for new style FPU register model in O32
- VDSO randomization.
- BCM47xx cleanups
- BCM47xx reimplement the way the kernel accesses NVRAM information.
- Random cleanups
- Add support for ATH25 platforms
- Remove pointless locking code in some PCI platforms.
- Some improvments to EVA support
- Minor Alchemy cleanup"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (185 commits)
MIPS: Add MFHC0 and MTHC0 instructions to uasm.
MIPS: Cosmetic cleanups of page table headers.
MIPS: Add CP0 macros for extended EntryLo registers
MIPS: Remove now unused definition of phys_t.
MIPS: Replace use of phys_t with phys_addr_t.
MIPS: Replace MIPS-specific 64BIT_PHYS_ADDR with generic PHYS_ADDR_T_64BIT
PCMCIA: Alchemy Don't select 64BIT_PHYS_ADDR in Kconfig.
MIPS: lib: memset: Clean up some MIPS{EL,EB} ifdefery
MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO
MIPS: <asm/types.h> fix indentation.
MAINTAINERS: Add entry for BMIPS multiplatform kernel
MIPS: Enable VDSO randomization
MIPS: Remove a temporary hack for debugging cache flushes in SMTC configuration
MIPS: Remove declaration of obsolete arch_init_clk_ops()
MIPS: atomic.h: Reformat to fit in 79 columns
MIPS: Apply `.insn' to fixup labels throughout
MIPS: Fix microMIPS LL/SC immediate offsets
MIPS: Kconfig: Only allow 32-bit microMIPS builds
MIPS: signal.c: Fix an invalid cast in ISA mode bit handling
MIPS: mm: Only build one microassembler that is suitable
...
|
|
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
|
|
Pull virtio updates from Michael Tsirkin:
"virtio: virtio 1.0 support, misc patches
This adds a lot of infrastructure for virtio 1.0 support. Notable
missing pieces: virtio pci, virtio balloon (needs spec extension),
vhost scsi.
Plus, there are some minor fixes in a couple of places.
Note: some net drivers are affected by these patches. David said he's
fine with merging these patches through my tree.
Rusty's on vacation, he acked using my tree for these, too"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (70 commits)
virtio_ccw: finalize_features error handling
virtio_ccw: future-proof finalize_features
virtio_pci: rename virtio_pci -> virtio_pci_common
virtio_pci: update file descriptions and copyright
virtio_pci: split out legacy device support
virtio_pci: setup config vector indirectly
virtio_pci: setup vqs indirectly
virtio_pci: delete vqs indirectly
virtio_pci: use priv for vq notification
virtio_pci: free up vq->priv
virtio_pci: fix coding style for structs
virtio_pci: add isr field
virtio: drop legacy_only driver flag
virtio_balloon: drop legacy_only driver flag
virtio_ccw: rev 1 devices set VIRTIO_F_VERSION_1
virtio: allow finalize_features to fail
virtio_ccw: legacy: don't negotiate rev 1/features
virtio: add API to detect legacy devices
virtio_console: fix sparse warnings
vhost: remove unnecessary forward declarations in vhost.h
...
|
|
Currently, when trying to reuse a socket, vxlan_sock_add will grab
vn->sock_lock, locate a reusable socket, inc refcount and release
vn->sock_lock.
But vxlan_sock_release() will first decrement refcount, and then grab
that lock. refcnt operations are atomic but as currently we have
deferred works which hold vs->refcnt each, this might happen, leading to
a use after free (specially after vxlan_igmp_leave):
CPU 1 CPU 2
deferred work vxlan_sock_add
... ...
spin_lock(&vn->sock_lock)
vs = vxlan_find_sock();
vxlan_sock_release
dec vs->refcnt, reaches 0
spin_lock(&vn->sock_lock)
vxlan_sock_hold(vs), refcnt=1
spin_unlock(&vn->sock_lock)
hlist_del_rcu(&vs->hlist);
vxlan_notify_del_rx_port(vs)
spin_unlock(&vn->sock_lock)
So when we look for a reusable socket, we check if it wasn't freed
already before reusing it.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Fixes: 7c47cedf43a8b3 ("vxlan: move IGMP join/leave to work queue")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb->mac_header
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the required firmware commands for A0 steering and a way to enable
that. The firmware support focuses on INIT_HCA, QUERY_HCA, QUERY_PORT,
QUERY_DEV_CAP and QUERY_FUNC_CAP commands. Those commands are used
to configure and query the device.
The different A0 DMFS (steering) modes are:
Static - optimized performance, but flow steering rules are
limited. This mode should be choosed explicitly by the user
in order to be used.
Dynamic - this mode should be explicitly choosed by the user.
In this mode, the FW works in optimized steering mode as long as
it can and afterwards automatically drops to classic (full) DMFS.
Disable - this mode should be explicitly choosed by the user.
The user instructs the system not to use optimized steering, even if
the FW supports Dynamic A0 DMFS (and thus will be able to use optimized
steering in Default A0 DMFS mode).
Default - this mode is implicitly choosed. In this mode, if the FW
supports Dynamic A0 DMFS, it'll work in this mode. Otherwise, it'll
work at Disable A0 DMFS mode.
Under SRIOV configuration, when the A0 steering mode is enabled,
older guest VF drivers who aren't using the RX QP allocation flag
(MLX4_RESERVE_A0_QP) will get a QP from the general range and
fail when attempting to register a steering rule. To avoid that,
the PF context behaviour is changed once on A0 static mode, to
require support for the allocation flag in VF drivers too.
In order to enable A0 steering, we use log_num_mgm_entry_size param.
If the value of the parameter is not positive, we treat the absolute
value of log_num_mgm_entry_size as a bit field. Setting bit 2 of this
bit field enables static A0 steering.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently QUERY_PORT is done as a part of QUERY_DEV_CAP firmware command.
Since we would like to use it without querying all device capabilities,
extract this part to be a function of its own.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a given flow steering rule is invalid in respect to the current
steering configuration, print the correct error message to the system log.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A0 hybrid steering is a form of high performance flow steering.
By using this mode, mlx4 cards use a fast limited table based steering,
in order to enable fast steering of unicast packets to a QP.
In order to implement A0 hybrid steering we allocate resources
from different zones:
(1) General range
(2) Special MAC-assigned QPs [RSS, Raw-Ethernet] each has its own region.
When we create a rss QP or a raw ethernet (A0 steerable and BF ready) QP,
we try hard to allocate the QP from range (2). Otherwise, we try hard not
to allocate from this range. However, when the system is pushed to its
limits and one needs every resource, the allocator uses every region it can.
Meaning, when we run out of raw-eth qps, the allocator allocates from the
general range (and the special-A0 area is no longer active). If we run out
of RSS qps, the mechanism tries to allocate from the raw-eth QP zone. If that
is also exhausted, the allocator will allocate from the general range
(and the A0 region is no longer active).
Note that if a raw-eth qp is allocated from the general range, it attempts
to allocate the range such that bits 6 and 7 (blueflame bits) in the
QP number are not set.
When the feature is used in SRIOV, the VF has to notify the PF what
kind of QP attributes it needs. In order to do that, along with the
"Eth QP blueflame" bit, we reserve a new "A0 steerable QP". According
to the combination of these bits, the PF tries to allocate a suitable QP.
In order to maintain backward compatibility (with older PFs), the PF
notifies which QP attributes it supports via QUERY_FUNC_CAP command.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The zone allocator is a mechanism which manages a few mlx4_bitmaps.
When allocating a resource, the user indicates the desired zone of
which this resource will be allocated from. If possible, the resource
will be allocated from this zone. Otherwise, the resource will be
allocated from a less-than, equal-to, higher-than priority zone,
according to the desired zone's properties with that respective
allocation order.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
