| Age | Commit message (Collapse) | Author |
|---|
|
Now that all of the GSI interrupts are handled uniformly,
change gsi_irq_type_update() so it takes a value. Have the
function assign that value to the cached mask of enabled GSI
IRQ types before writing it to hardware.
Note that gsi_irq_teardown() will only be called after
gsi_irq_disable(), so it's not necessary for the former
to disable all IRQ types. Get rid of that.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Most GSI general errors are unrecoverable without a full reset.
Despite that, we want to receive these errors so we can at least
report what happened before whatever undefined behavior ensues.
Explicitly disable all such interrupts in gsi_irq_setup(), then
enable those we want in gsi_irq_enable(). List the interrupt types
we are interested in (everything but breakpoint) explicitly rather
than using GSI_CNTXT_GSI_IRQ_ALL, and remove that symbol's
definition.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is possible for other execution environments (EEs, like the modem)
to request changes to local (AP) channel or event ring state. We do
not support this feature.
In gsi_irq_setup(), explicitly zero the mask that defines which
channels are permitted to generate inter-EE channel state change
interrupts. Do the same for the event ring mask.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A GSI channel must be started in order to use it to perform a
transfer data (or command) transaction. And the only time we'll see
an IEOB interrupt is if we send a transaction to a started channel.
Therefore we do not need to have the IEOB interrupt type enabled
until at least one channel has been started. And once the last
started channel has been stopped, we can disable the IEOB interrupt
type again.
We already enable the IEOB interrupt for a particular channel only
when it is started. Extend that by having the IEOB interrupt *type*
be enabled only when at least one channel is in STARTED state.
Disallow all channels from triggering the IEOB interrupt in
gsi_irq_setup(). We only enable an channel's interrupt when
needed, so there is no longer any need to zero the channel mask
in gsi_irq_disable().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The completion of a generic EE GSI command is signaled by a global
interrupt of type GP_INT1. The only other used type for a global
interrupt is a hardware error report.
First, disallow all global interrupt types in gsi_irq_setup(). We
want to know about hardware errors, so re-enable the interrupt type
in gsi_irq_enable(), to allow hardware errors to be reported.
Disable that interrupt type again in gsi_irq_disable().
We only issue generic EE commands one at a time, and there's no
reason to keep the completion interrupt enabled when no generic
EE command is pending. We furthermore have no need to enable the
GP_INT2 or GP_INT3 interrupt types (which aren't used).
The change in gsi_irq_enable() makes GSI_CNTXT_GLOB_IRQ_ALL unused,
so get rid of it. Have gsi_generic_command() enable the GP_INT1
interrupt type (in addition to the ERROR_INT type) only while a
generic command is pending.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A GSI event ring causes an event control interrupt to fire whenever
its state changes (between NOT_ALLOCATED and ALLOCATED). No event
ring should ever change state except when we request it to.
Currently, we permit *all* events rings to generate event control
interrupts--even those that are never used. And we enable event
control interrupts essentially at all times, from setup to teardown.
Instead, only enable the event control interrupt type for the
duration of an event ring command, and when doing so, only allow
the event ring being operated upon to cause the interrupt to fire.
Disallow all event rings from issuing the event control interrupt
in gsi_irq_setup().
Because an event ring's interrupt is only enabled when needed,
there is no longer any need to zero the event channel mask in
gsi_irq_disable().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A GSI channel causes a channel control interrupt to fire whenever
its state changes (between NOT_ALLOCATED, ALLOCATED, STARTED, etc.).
We do not support inter-EE channel commands (initiated by other EEs),
so no channel should ever change state except when we request it to.
Currently, we permit *all* channels to generate channel control
interrupts--even those that are never used. And we enable channel
control interrupts essentially at all times, from setup to teardown.
Instead, disable all channel control interrupts initially in
gsi_irq_setup(), and only enable the channel control interrupt
type for the duration of a channel command. When doing so, only
allow the channel being operated upon to cause the interrupt to
fire.
Because a channel's interrupt is now enabled only when needed (one
channel at a time), there is no longer any need to zero the channel
mask in gsi_irq_disable().
Add new gsi_irq_type_enable() and gsi_irq_type_disable() as helper
functions to control whether a given GSI interrupt type is enabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Keep track of the set of GSI interrupt types that are currently
enabled by recording the mask value to write (or last written) to
the TYPE_IRQ_MSK register.
Create a new helper function gsi_irq_type_update() to handle
actually writing the register.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce gsi_irq_setup() and gsi_irq_teardown() to disable all
GSI interrupts when first setting up GSI hardware, and to clean
things up when we're done.
Re-enable all GSI interrupt types in gsi_irq_enable(), but do
so only after each of the type-specific interrupt masks has
been configured. Similarly, disable all interrupt types in
gsi_irq_disable()--first--before zeroing out the type-specific
masks.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Define the GSI interrupt types with an enumerated type whose values
are the bit positions representing each interrupt type. Include a
short comment describing how each interrupt type is used.
Build up the enabled interrupt mask explicitly in gsi_irq_enable(),
and get rid of the definition of GSI_CNTXT_TYPE_IRQ_MSK_ALL.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rename the "event_enable_bitmap" field of the GSI structure to be
"ieob_enabled_bitmap". An upcoming patch will cache the last value
stored for another interrupt mask and this is a more direct naming
convention to follow.
Add a few comments to explain the bitmap fields in the GSI structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce gsi_irq_init() and gsi_irq_exit(), to encapsulate looking
up the GSI IRQ and registering its handler. Call gsi_irq_init() a
little later in gsi_init(), and initialize the completion earlier.
The IRQ handler accesses both the GSI virtual memory pointer and the
completion, and this way these things will have been initialized
before the gsi_irq() can ever be called.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The GSI code is now exposed to IPA version numbers, and we handle
version-specific behavior based on the IPA version.
Modify some comments that talk about GSI versions so they reference
IPA versions instead. Correct version number errors in a couple of
these comments.
The (comment) mapping between IPA and GSI versions in the definition
of the ipa_version enumerated type remains.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This driver transports LAPB (X.25 link layer) frames over TTY links.
I can safely say that this driver has no actual user because it was
not working at all until:
commit 8fdcabeac398 ("drivers/net/wan/x25_asy: Fix to make it work")
The code in its current state still has problems:
1.
The uses of "struct x25_asy" in x25_asy_unesc (when receiving) and in
x25_asy_write_wakeup (when sending) are not protected by locks against
x25_asy_change_mtu's changing of the transmitting/receiving buffers.
Also, all "netif_running" checks in this driver are not protected by
locks against the ndo_stop function.
2.
The driver stops all TTY read/write when the netif is down.
I think this is not right because this may cause the last outgoing frame
before the netif goes down to be incompletely transmitted, and the first
incoming frame after the netif goes up to be incompletely received.
And there may also be other problems.
I was planning to fix these problems but after recent discussions about
deleting other old networking code, I think we may just delete this
driver, too.
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20201105073434.429307-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch fixes NULL pointer dereference due to NULL pcs_config
in pcs_ops.
Fixes: e4e143e26ce8 ("net: macb: add support for high speed interface")
Reported-by: Nicolas Ferre <Nicolas.Ferre@microchip.com>
Link: https://lore.kernel.org/netdev/2db854c7-9ffb-328a-f346-f68982723d29@microchip.com/
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/1604599113-2488-1-git-send-email-pthombar@cadence.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The initialization for err with 0 seems useless, as it is soon updated
with -ENOMEM. So, we can remove it.
Changes since v1:
-Keep -ENOMEM still.
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Link: https://lore.kernel.org/r/1604541244-3241-1-git-send-email-dong.menglong@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the gcc warning:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:2673:9: warning: this 'for' clause does not guard... [-Wmisleading-indentation]
2673 | for (i = 0; i < n; ++i) \
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Link: https://lore.kernel.org/r/1604467444-23043-1-git-send-email-kaixuxia@tencent.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MDIO spec does not require an MDC at all times, only when MDIO
transactions are occurring. This patch allows the xilinx_axienet
driver to disable the MDC when not in use, and re-enable it when
needed. It also simplifies the driver by removing MDC disable
and enable in device reset sequence.
Signed-off-by: Clayton Rayment <clayton.rayment@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce helper functions to enable/disable MDIO interface clock. This
change serves a preparatory patch for the coming feature to dynamically
control the management bus clock.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 16b5f5ce351f8709a6b518cc3cbf240c378305bf
where it restructures do_reset. There are patches being tested that
would require major rework if this is committed first.
We will resend this after the other patches have been applied.
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20201106191745.1679846-1-drt@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.10-rc3, including fixes from wireless, can, and
netfilter subtrees.
Current merge window - bugs in new features:
- can: isotp: isotp_rcv_cf(): enable RX timeout handling in
listen-only mode
Previous releases - regressions:
- mac80211:
- don't require VHT elements for HE on 2.4 GHz
- fix regression where EAPOL frames were sent in plaintext
- netfilter:
- ipset: Update byte and packet counters regardless of whether
they match
- ip_tunnel: fix over-mtu packet send by allowing fragmenting even if
inner packet has IP_DF (don't fragment) set in its header (when
TUNNEL_DONT_FRAGMENT flag is not set on the tunnel dev)
- net: fec: fix MDIO probing for some FEC hardware blocks
- ip6_tunnel: set inner ipproto before ip6_tnl_encap to un-break gso
support
- sctp: Fix COMM_LOST/CANT_STR_ASSOC err reporting on big-endian
platforms, sparse-related fix used the wrong integer size
Previous releases - always broken:
- netfilter: use actual socket sk rather than skb sk when routing
harder
- r8169: work around short packet hw bug on RTL8125 by padding frames
- net: ethernet: ti: cpsw: disable PTPv1 hw timestamping
advertisement, the hardware does not support it
- chelsio/chtls: fix always leaking ctrl_skb and another leak caused
by a race condition
- fix drivers incorrectly writing into skbs on TX:
- cadence: force nonlinear buffers to be cloned
- gianfar: Account for Tx PTP timestamp in the skb headroom
- gianfar: Replace skb_realloc_headroom with skb_cow_head for PTP
- can: flexcan:
- remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
- add ECC initialization for VF610 and LX2160A
- flexcan_remove(): disable wakeup completely
- can: fix packet echo functionality:
- peak_canfd: fix echo management when loopback is on
- make sure skbs are not freed in IRQ context in case they need to
be dropped
- always clone the skbs to make sure they have a reference on the
socket, and prevent it from disappearing
- fix real payload length return value for RTR frames
- can: j1939: return failure on bind if netdev is down, rather than
waiting indefinitely
Misc:
- IPv6: reply ICMP error if the first fragment don't include all
headers to improve compliance with RFC 8200"
* tag 'net-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
ionic: check port ptr before use
r8169: work around short packet hw bug on RTL8125
net: openvswitch: silence suspicious RCU usage warning
chelsio/chtls: fix always leaking ctrl_skb
chelsio/chtls: fix memory leaks caused by a race
can: flexcan: flexcan_remove(): disable wakeup completely
can: flexcan: add ECC initialization for VF610
can: flexcan: add ECC initialization for LX2160A
can: flexcan: remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
can: mcp251xfd: remove unneeded break
can: mcp251xfd: mcp251xfd_regmap_nocrc_read(): fix semicolon.cocci warnings
can: mcp251xfd: mcp251xfd_regmap_crc_read(): increase severity of CRC read error messages
can: peak_canfd: pucan_handle_can_rx(): fix echo management when loopback is on
can: peak_usb: peak_usb_get_ts_time(): fix timestamp wrapping
can: peak_usb: add range checking in decode operations
can: xilinx_can: handle failure cases of pm_runtime_get_sync
can: ti_hecc: ti_hecc_probe(): add missed clk_disable_unprepare() in error path
can: isotp: padlen(): make const array static, makes object smaller
can: isotp: isotp_rcv_cf(): enable RX timeout handling in listen-only mode
can: isotp: Explain PDU in CAN_ISOTP help text
...
|
|
Previous patches added the ability to program nexthop objects.
Therefore, no longer forbid the programming of routes that point to such
objects.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement dummy nexthop "offload" in the driver by storing currently
"programmed" nexthops in a hash table. Each nexthop in the hash table is
marked with "trap" indication and increments the nexthops resource
occupancy.
This will later allow us to test the nexthop offload API on top of
netdevsim.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Spectrum ASIC has a dedicated table where nexthops (i.e., adjacency
entries) are populated. The size of this table can be controlled via
devlink-resource.
Add such a resource to netdevsim so that its occupancy will reflect the
number of nexthop objects currently programmed to the device.
By limiting the size of the resource, error paths could be exercised and
tested.
Example output:
# devlink resource show netdevsim/netdevsim10
netdevsim/netdevsim10:
name IPv4 size unlimited unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
resources:
name fib size unlimited occ 4 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
name fib-rules size unlimited occ 3 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
name IPv6 size unlimited unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
resources:
name fib size unlimited occ 1 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
name fib-rules size unlimited occ 2 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
name nexthops size unlimited occ 0 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This will be used by the next patch which extends the function to replay
all the existing nexthops to the notifier block being registered.
Device drivers will be able to pass extack to the function since it is
passed to them upon reload from devlink.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert the sole listener of the nexthop notification chain (the VXLAN
driver) to the new notification info.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-11-03
This series includes updates to mlx5 software steering component.
1) Few improvements in the DR area, such as removing unneeded checks,
renaming to better general names, refactor in some places, etc.
2) Software steering (DR) Memory management improvements
This patch series contains SW Steering memory management improvements:
using buddy allocator instead of an existing bucket allocator, and
several other optimizations.
The buddy system is a memory allocation and management algorithm
that manages memory in power of two increments.
The algorithm is well-known and well-described, such as here:
https://en.wikipedia.org/wiki/Buddy_memory_allocation
Linux uses this algorithm for managing and allocating physical pages,
as described here:
https://www.kernel.org/doc/gorman/html/understand/understand009.html
In our case, although the algorithm in principal is similar to the
Linux physical page allocator, the "building blocks" and the circumstances
are different: in SW steering, buddy allocator doesn't really allocates
a memory, but rather manages ICM (Interconnect Context Memory) that was
previously allocated and registered.
The ICM memory that is used in SW steering is always power
of 2 (order), so buddy system is a good fit for this.
Patches in this series:
[PATH 4] net/mlx5: DR, Add buddy allocator utilities
This patch adds a modified implementation of a well-known buddy allocator,
adjusted for SW steering needs: the algorithm in principal is similar to
the Linux physical page allocator, but in our case buddy allocator doesn't
really allocate a memory, but rather manages ICM memory that was previously
allocated and registered.
[PATH 5] net/mlx5: DR, Handle ICM memory via buddy allocation instead of bucket management
This patch changes ICM management of SW steering to use buddy-system mechanism
Instead of the previous bucket management.
[PATH 6] net/mlx5: DR, Sync chunks only during free
This patch makes syncing happen only when freeing memory chunks.
[PATH 7] net/mlx5: DR, ICM memory pools sync optimization
This patch adds tracking of pool's "hot" memory and makes the
check whether steering sync is required much shorter and faster.
[PATH 8] net/mlx5: DR, Free buddy ICM memory if it is unused
This patch adds tracking buddy's used ICM memory,
and frees the buddy if all its memory becomes unused.
3) Misc code cleanups
* tag 'mlx5-updates-2020-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net: mlx5: Replace in_irq() usage
net/mlx5: Cleanup kernel-doc warnings
net/mlx4: Cleanup kernel-doc warnings
net/mlx5e: Validate stop_room size upon user input
net/mlx5: DR, Free unused buddy ICM memory
net/mlx5: DR, ICM memory pools sync optimization
net/mlx5: DR, Sync chunks only during free
net/mlx5: DR, Handle ICM memory via buddy allocation instead of buckets
net/mlx5: DR, Add buddy allocator utilities
net/mlx5: DR, Rename matcher functions to be more HW agnostic
net/mlx5: DR, Rename builders HW specific names
net/mlx5: DR, Remove unused member of action struct
====================
Link: https://lore.kernel.org/r/20201105201242.21716-1-saeedm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support ECM mode based on cdc_ether with relative mii functions,
when CONFIG_USB_RTL8152 is not set, or the device is not supported
by r8152 driver.
Both r8152 and r8153_ecm would check the return value of
rtl8152_get_version() in porbe(). If rtl8152_get_version()
return none zero value, the r8152 is used for the device
with vendor mode. Otherwise, the r8153_ecm is used for the
device with ECM mode.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/1394712342-15778-392-Taiwan-albertk@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds a new network driver implementing MHI transport for
network packets. Packets can be in any format, though QMAP (rmnet)
is the usual protocol (flow control + PDN mux).
It support two MHI devices, IP_HW0 which is, the path to the IPA
(IP accelerator) on qcom modem, And IP_SW0 which is the software
driven IP path (to modem CPU).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1604424234-24446-2-git-send-email-loic.poulain@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Willy Liu <willy.liu@realtek.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Willy Liu <willy.liu@realtek.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It seems there are cases where the interrupts are handled by another
entity (ie an IRQ controller embedded inside the PHY) and do not need
any other interraction from phylib. For this kind of PHYs, like the
RTL8366RB, add the genphy_handle_interrupt_no_ack() function which just
triggers the link state machine.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Michael Walle <michael@walle.cc>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com> # VSC8514
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Also, remove the .did_interrupt() callback since it's not anymore used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com> # VSC8514
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to the comment describing the phy_mac_interrupt() function, it
it intended to be used by MAC drivers which have noticed a link change
thus its use in the mscc PHY driver is improper and, most probably, was
added just because phy_trigger_machine() was not exported.
Now that we have acces to trigger the link state machine, use directly
the phy_trigger_machine() function to notify a link change detected by
the PHY driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As a first step into making phylib and all PHY drivers to actually
have support for shared IRQs, make the .ack_interrupt() callback
optional.
After all drivers have been moved to implement the generic
interrupt handle, the phy_drv_supports_irq() check will be
changed again to only require the .handle_interrupts() callback.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case of a board which uses a shared IRQ we can easily end up with an
IRQ storm after a forced reboot.
For example, a 'reboot -f' will trigger a call to the .shutdown()
callbacks of all devices. Because phylib does not implement that hook,
the PHY is not quiesced, thus it can very well leave its IRQ enabled.
At the next boot, if that IRQ line is found asserted by the first PHY
driver that uses it, but _before_ the driver that is _actually_ keeping
the shared IRQ asserted is probed, the IRQ is not going to be
acknowledged, thus it will keep being fired preventing the boot process
of the kernel to continue. This is even worse when the second PHY driver
is a module.
To fix this, implement the .shutdown() callback and disable the
interrupts if these are used.
Note that we are still susceptible to IRQ storms if the previous kernel
exited with a panic or if the bootloader left the shared IRQ active, but
there is absolutely nothing we can do about these cases.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These functions are currently used by phy_interrupt() to either signal
an error condition or to trigger the link state machine. In an attempt
to actually support shared PHY IRQs, export these two functions so that
the actual PHY drivers can use them.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The switch has two controllable I/Os which are usually connected to LEDs. This
is useful to immediately visually see the PTP status.
These provide two signals:
* is_gm
This LED can be activated if the current device is the grand master in that
PTP domain.
* sync_good
This LED can be activated if the current device is in sync with the network
time.
Expose these via the LED framework to be controlled via user space
e.g. linuxptp.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
