| Age | Commit message (Collapse) | Author |
|---|
|
Rearrange functions to allow removal of some forward declarations.
Make certain global functions static along the way.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Make needlessly global functions static. In a couple of cases this
requires removing forward declarations and reordering functions.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add some debug printks if we encounter a potentially bad receive
return descriptor.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Use netif_msg_* for console messages emitted by the driver. Add a
parameter to allow control of messaging at driver startup, and also
add the ability to control it with ethtool.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Use skb->csum_start for tx checksum offload preparation. Also swap
the variables css and cso so they hold the intended values of csum
start and offset, respectively.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The transmit packet descriptor consists of four 32-bit words, with word 3
upper bits overloaded depending upon the condition of its bits 3 and 4.
The driver currently duplicates all word 2 and some word 3 register bit
definitions unnecessarily and also uses a set of nested structures in its
definition of the TPD without good cause. This patch adds a lengthy
comment describing the TPD, eliminates duplicate TPD bit definitions,
and simplifies the TPD structure itself. It also expands the TSO check
to correctly handle custom checksum versus TSO processing using the revised
TPD definitions. Finally, shorten some variable names in the transmit
processing path to reduce line lengths, rename some variables to better
describe their purpose (e.g., nseg versus m), and add a comment or two
to better describe what the code is doing.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add the ethtool register dump option to the atl1 driver.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The L1 tx packet descriptor expects TCP Header Length to be expressed as a
number of 32-bit dwords. The atl1 driver uses tcp_hdrlen() to populate the
field, but tcp_hdrlen() returns the header length in bytes, not in dwords.
Add a shift to convert tcp_hdrlen() to dwords when we write it to the tpd.
Also, some of our bit assignments are made to the wrong tpd words. Change
those to the correct words.
Finally, since all this fixes TSO, enable TSO by default.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Acked-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The future atl2 driver and the existing atl1 driver can share certain
functions and definitions. Move these shareable functions and definitions
out of atl1-specific files and into atlx.c and atlx.h. Some transitory
hackery will be present until atl2 is merged.
Reduce the number of source files by moving ethtool, hw, and param
functions from separate files into atl1_main.c, then rename it to just
atl1.c.
Move all atl1-specific definitions from atl1_hw.h to atl1.h.
Finally, clean up to make checkpatch.pl happy.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
In preparation for a future Atheros L2 NIC driver (called atl2), relocate
the atl1 driver into a new /drivers/net/atlx directory that will ultimately
be shared with the future atl2 driver.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The xircom_tulip_cb driver has been replaced the xircom_cb driver, and
since it depended on BROKEN_ON_SMP it e.g. was no longer present in many
distribution kernels.
This patch therefore removes it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
All the hardware supported by this driver is now supported
by the skge driver. The last remaining issue was support for ancient
dual port SysKonnect fiber boards, and the skge driver now does these
correctly (p.s. sk98lin was always broken on these old dual port
boards anyway).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Indirect scanning ('iwlist scan') should report information about
hidden APs. When an AP is hidden it does not respond to active scanning,
we thus have to use passive scanning to locate these APs.
This fixes http://bughost.org/bugzilla/show_bug.cgi?id=1499
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch moves a number to an understandable define
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fix debug print out endianity issue for bitmap
Since u64 and le64 variables are casted to unsigned long long,
after patch 'wireless: correct warnings from using '%llx' for type 'u64'
also bitmaps need to be converted to native endianity
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch puts in use eeprom from iwlcore module
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Also fix a copy and paste error in header of iwl-core.c. This file
is not dual licensed.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch removes iwlYYY_BROADCAST_ID from run time usage.
hw_setting.sta_bcast_id is used instead.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Only rt2400pci can have the preamble bit set in the PLCP value,
for all other drivers it should not be cleared since that will
conflict with the plcp values for OFDM rates.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Version bump to 2.1.4
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
After sampling hundreds of RX frame descriptors,
the results were conclusive:
- The Ralink documentation regarding the SIGNAL and RSSI are wrong.
It turns out that of the 5 BBR registers, we should not use BBR0 and BBR1
for SIGNAL and RSSI respectively, but actually BBR1 and BBR2.
BBR0 does show values, but the exact meaning remains unclear,
but they cannot be translated into a SIGNAL or RSSI field.
BBR3, BBR4 and BBR5 are always 0, so their meaning is unknown.
As it turns out, the reported SIGNAL is the PLCP value, this
in contradiction to what was expected looking at rt2500pci which
only reported the PLCP values for OFDM rates and bitrate values
for CCK rates.
This means we should let the driver raise the flag about the contents
of the SIGNAL field so rt2x00lib can always do the right thing based
on what the driver reports.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Due to a terrible typo the RX DMA base address
was initialized to the beacon base address.
Obviously bad things happen with bugs like that....
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The basic rate which is configured in the register
should not match all supported rates, but only the _basic_ rates.
Fix this by adding a new flag to the rt2x00_rate structure
and whenever the mode is changed, loop over all available rates
for that band to get the basic rate mask.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Whatever mode we are in, according to the legacy drivers
we should always enable TSF ticking/counting.
We should also always enable the TBCN/TBTT field,
this field is only disabled during beacon regeneration.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
rt2x00dev isn't interested in the rt2x00leds_register() value
anyway. So lets make it return void to even prevent people from
assuming there is anybody interested in the returnvalue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rename config_preamble() to config_erp() and cleanup argument
list by putting it all into a single structure.
This will make the function more meaningful and easier to
expand later. This second option is mostly intended to make
the patch "mac80211: proper short-slot handling" from Johannes Berg
easier to apply for rt2x00.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When mac sets the IEEE80211_TXCTL_SEND_AFTER_DTIM flag, we should
check if the ATIM queue is available in the driver and put the
frame in that queue for proper behavior (send frame after beacon interval).
Unfortunately not all drivers have this ATIM queue, and will lack
this feature for now.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
rt2x00lib should filter SW diversity out before sending any configuration
changes to the driver. When rt2x00lib fails to do this, it is important
that such events are reported because it _must_ be fixed.
So upgrading the error level to a BUG_ON() which will make sure
this bug gets noticed whenever it happens.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
rt2x00lib depended on 2 crc algorithms because rt61/rt73
use a different algorithm then rt2800. This means that
even when only 1 algorithm was needed, the dependency was
still present for both.
By moving the checksum generation to the driver we can clean
up 2 annoying flags (which indicated which checksum was required)
and move the dependency to where it belongs: the driver.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The queue->lock could be grabbed from interrupt context,
which could lead to lockdep panic like this:
kernel: ======================================================
kernel: [ INFO: soft-safe -> soft-unsafe lock order detected ]
kernel: 2.6.25-0.95.rc4.fc9 #1
kernel: ------------------------------------------------------
kernel: rt2500pci/1251 [HC0[0]:SC0[1]:HE1:SE0] is trying to acquire:
kernel: (&queue->lock){--..}, at: [<ffffffff88213339>] rt2x00queue_get_entry+0x5a/0x81 [rt2x00lib]
kernel:
kernel: and this task is already holding:
kernel: (_xmit_IEEE80211){-...}, at: [<ffffffff8122e9a3>] __qdisc_run+0x84/0x1a9
kernel: which would create a new lock dependency:
kernel: (_xmit_IEEE80211){-...} -> (&queue->lock){--..}
kernel:
kernel: but this new dependency connects a soft-irq-safe lock:
kernel: (_xmit_ETHER){-+..}
kernel: ... which became soft-irq-safe at:
kernel: [<ffffffffffffffff>] 0xffffffffffffffff
kernel:
kernel: to a soft-irq-unsafe lock:
kernel: (&queue->lock){--..}
kernel: ... which became soft-irq-unsafe at:
kernel: ... [<ffffffff810545a2>] __lock_acquire+0x62d/0xd63
kernel: [<ffffffff81054d36>] lock_acquire+0x5e/0x78
kernel: [<ffffffff812a1497>] _spin_lock+0x26/0x53
kernel: [<ffffffff88212f98>] rt2x00queue_reset+0x16/0x40 [rt2x00lib]
kernel: [<ffffffff88212fd4>] rt2x00queue_alloc_entries+0x12/0xab [rt2x00lib]
kernel: [<ffffffff88213091>] rt2x00queue_initialize+0x24/0xf2 [rt2x00lib]
kernel: [<ffffffff88212036>] rt2x00lib_start+0x3b/0xd4 [rt2x00lib]
kernel: [<ffffffff88212609>] rt2x00mac_start+0x18/0x1a [rt2x00lib]
kernel: [<ffffffff881b9a4b>] ieee80211_open+0x1f3/0x46d [mac80211]
kernel: [<ffffffff8121d980>] dev_open+0x4d/0x8b
kernel: [<ffffffff8121d41e>] dev_change_flags+0xaf/0x172
kernel: [<ffffffff81224fc2>] do_setlink+0x276/0x338
kernel: [<ffffffff81225198>] rtnl_setlink+0x114/0x116
kernel: [<ffffffff812262fc>] rtnetlink_rcv_msg+0x1d8/0x1f9
kernel: [<ffffffff8123649a>] netlink_rcv_skb+0x3e/0xac
kernel: [<ffffffff8122611a>] rtnetlink_rcv+0x29/0x33
kernel: [<ffffffff81235eed>] netlink_unicast+0x1fe/0x26b
kernel: [<ffffffff81236224>] netlink_sendmsg+0x2ca/0x2dd
kernel: [<ffffffff812103b3>] sock_sendmsg+0xfd/0x120
kernel: [<ffffffff812105a8>] sys_sendmsg+0x1d2/0x23c
kernel: [<ffffffff8100c1c7>] tracesys+0xdc/0xe1
kernel: [<ffffffffffffffff>] 0xffffffffffffffff
This can be fixed by using the irqsave/irqrestore versions
during the queue->lock handling.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix trivial log message.
Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When fixing up the packet alignment, if we had to add 2 bytes to the front of
the skb we need to remember to take them off the end afterwards. This fixes
reception of encrypted packets which were otherwise failing with an invalid
ICV.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We should not write 0 to the beacon sync register during
config_intf() since that will clear out the beacon interval
and forces the beacon to be send out at the lowest interval.
(reported by Mattias Nissler).
The side effect of the same bug was that while working with
multiple virtual AP interfaces a change for any of those
interfaces would disable beaconing untill an beacon update
was provided.
This is resolved by only updating the TSF_SYNC value during
config_intf(). In update_beacon() we disable beaconing
temporarily to prevent fake beacons to be transmitted.
Finally kick_tx_queue() will enable beaconing again.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In rt2x00lib_write_tx_desc() the skb->data and skb->len fields
were incorrectly used. For USB drivers both of those values
contain invalid data (skb->data points to the device descriptor,
skb->len contains the frame _and_ descriptor length).
Instead of using the skbuffer fields we should use the skbdesc
fields which are correctly initialized and contain all the data
that we need.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
rxdesc->size is unitialized before the desriptor has been read.
Move the truncation of the sk buffer to the moment all variables
have been initialized.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
skbdesc->desc_len is uninitialized at the start
of the function. So it is a _bad_ idea to use it...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The sizeof() operator was incorrectly applied to the pointer, not the struct.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In the TX path, the driver didn't copy the TX control data structure. Thus, it
was invalid in the TX done handler, causing serious trouble and misbehaviour.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some architectures give problems when reading
RX frame descriptor words when the descriptor
is not aligned on a 4 byte boundrary.
Due to optimalizations for the ieee80211 payload
4 byte alignment, it is no longer guarenteed
that the descriptor is placed on the 4 byte
boundrary (In fact, for rt73usb it is absolutely
never aligned to 4 bytes, for rt2500usb it depends
on the length of the payload).
This will copy the descriptor to a 4 byte aligned
location before it is read for the first time.
This will also move the payload data alignment
in rt2x00usb (instead of inside the driver) where
it has always belonged.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rename members of ndis_80211_* structures to match the style of
the rest of the code.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rename enums and structures to ndis_80211_* for greater readability.
Also change order so that enumerations are presented first.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
(test == true) is not nice.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
After my bit scan re-writing the SIOCSIWSCAN wext ioctl no longer supported
scanning for a specific SSID. However, wpa_supplicant is a possible user of
this ioctl, so here is code that add's this.
While passing, removed even more of the debugfs-based scanning. You can (and
should) the SIOCSIWSCAN to ask for scans, so there is no need for
proprietary interfaces for scanning. And, besides, the scan result couldn't
be used further, e.g. not for associating.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: <Larry.Finger@lwfinger.net>
Cc: <stefano.brivio@polimi.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
b43_mac_{enable,suspend}() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add suspend/resume handlers to rt2x00rfkill to have it stop
the input-polldev and prevent it from calling rt2x00 during
suspend period. This could lead to a NULL pointer fault when
rt2x00 suspended, but polldev send a request, because
the csr_addr is NULL.
Also don't let the rfkill allocation/registration block
the initialization of the entire device. Just print a warning
and continue as if nothing happened.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Once ah has been freed, it may not be accessed. Set ATH_STAT_INVALID
bit to make the interrupt handler return IRQ_NONE without accessing ah.
This fixes oops on unload with CONFIG_DEBUG_SHIRQ enabled.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit 61bca6eb85c863603d6054530e2f65c3b9aba85b b43: rewrite A PHY initialization
has a typo, the result of the register read should be masked, not the
register offset.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The gelic driver uses two net interfaces, one for ethernet and the
other for wireless. They share same MAC address and use 'eth' prefix
for the name.
As udev uses the MAC address to check uniqueness, this is
somewhat problematic. So change the prefix of the network interface
name for the wireless so that udev can have an easy way to distinguish
interfaces.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
