summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2020-04-22net: dsa: b53: b53_arl_rw_op() needs to select IVL or SVLFlorian Fainelli
Flip the IVL_SVL_SELECT bit correctly based on the VLAN enable status, the default is to perform Shared VLAN learning instead of Individual learning. Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: dsa: b53: Rework ARL bin logicFlorian Fainelli
When asking the ARL to read a MAC address, we will get a number of bins returned in a single read. Out of those bins, there can essentially be 3 states: - all bins are full, we have no space left, and we can either replace an existing address or return that full condition - the MAC address was found, then we need to return its bin index and modify that one, and only that one - the MAC address was not found and we have a least one bin free, we use that bin index location then The code would unfortunately fail on all counts. Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: dsa: b53: Fix ARL register definitionsFlorian Fainelli
The ARL {MAC,VID} tuple and the forward entry were off by 0x10 bytes, which means that when we read/wrote from/to ARL bin index 0, we were actually accessing the ARLA_RWCTRL register. Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: dsa: b53: Fix valid setting for MDB entriesFlorian Fainelli
When support for the MDB entries was added, the valid bit was correctly changed to be assigned depending on the remaining port bitmask, that is, if there were no more ports added to the entry's port bitmask, the entry now becomes invalid. There was another assignment a few lines below that would override this which would invalidate entries even when there were still multiple ports left in the MDB entry. Fixes: 5d65b64a3d97 ("net: dsa: b53: Add support for MDB") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: dsa: b53: Lookup VID in ARL searches when VLAN is enabledFlorian Fainelli
When VLAN is enabled, and an ARL search is issued, we also need to compare the full {MAC,VID} tuple before returning a successful search result. Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22vrf: Check skb for XFRM_TRANSFORMED flagDavid Ahern
To avoid a loop with qdiscs and xfrms, check if the skb has already gone through the qdisc attached to the VRF device and then to the xfrm layer. If so, no need for a second redirect. Fixes: 193125dbd8eb ("net: Introduce VRF device driver") Reported-by: Trev Larock <trev@larock.ca> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: phy: microchip_t1: add lan87xx_phy_init to initialize the lan87xx phy.Yuiko Oshino
lan87xx_phy_init() initializes the lan87xx phy hardware including its TC10 Wake-up and Sleep features. Fixes: 3e50d2da5850 ("Add driver for Microchip LAN87XX T1 PHYs") Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com> v0->v1: - Add more details in the commit message and source comments. - Update to the latest initialization sequences. - Add access_ereg_modify_changed(). - Fix access_ereg() to access SMI bank correctly. Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-21net: stmmac: Enable SERDES power up/down sequenceVoon Weifeng
This patch is to enable Intel SERDES power up/down sequence. The SERDES converts 8/10 bits data to SGMII signal. Below is an example of HW configuration for SGMII mode. The SERDES is located in the PHY IF in the diagram below. <-----------------GBE Controller---------->|<--External PHY chip--> +----------+ +----+ +---+ +----------+ | EQoS | <-GMII->| DW | < ------ > |PHY| <-SGMII-> | External | | MAC | |xPCS| |IF | | PHY | +----------+ +----+ +---+ +----------+ ^ ^ ^ ^ | | | | +---------------------MDIO-------------------------+ PHY IF configuration and status registers are accessible through mdio address 0x15 which is defined as mdio_adhoc_addr. During D0, The driver will need to power up PHY IF by changing the power state to P0. Likewise, for D3, the driver sets PHY IF power state to P3. Signed-off-by: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-21net: broadcom: convert to devm_platform_ioremap_resource_byname()Dejin Zheng
Use the function devm_platform_ioremap_resource_byname() to simplify source code which calls the functions platform_get_resource_byname() and devm_ioremap_resource(). Remove also a few error messages which became unnecessary with this software refactoring. Suggested-by: Markus Elfring <Markus.Elfring@web.de> Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-21macvlan: fix null dereference in macvlan_device_event()Taehee Yoo
In the macvlan_device_event(), the list_first_entry_or_null() is used. This function could return null pointer if there is no node. But, the macvlan module doesn't check the null pointer. So, null-ptr-deref would occur. bond0 | +----+-----+ | | macvlan0 macvlan1 | | dummy0 dummy1 The problem scenario. If dummy1 is removed, 1. ->dellink() of dummy1 is called. 2. NETDEV_UNREGISTER of dummy1 notification is sent to macvlan module. 3. ->dellink() of macvlan1 is called. 4. NETDEV_UNREGISTER of macvlan1 notification is sent to bond module. 5. __bond_release_one() is called and it internally calls dev_set_mac_address(). 6. dev_set_mac_address() calls the ->ndo_set_mac_address() of macvlan1, which is macvlan_set_mac_address(). 7. macvlan_set_mac_address() calls the dev_set_mac_address() with dummy1. 8. NETDEV_CHANGEADDR of dummy1 is sent to macvlan module. 9. In the macvlan_device_event(), it calls list_first_entry_or_null(). At this point, dummy1 and macvlan1 were removed. So, list_first_entry_or_null() will return NULL. Test commands: ip netns add nst ip netns exec nst ip link add bond0 type bond for i in {0..10} do ip netns exec nst ip link add dummy$i type dummy ip netns exec nst ip link add macvlan$i link dummy$i \ type macvlan mode passthru ip netns exec nst ip link set macvlan$i master bond0 done ip netns del nst Splat looks like: [ 40.585687][ T146] general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP DEI [ 40.587249][ T146] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] [ 40.588342][ T146] CPU: 1 PID: 146 Comm: kworker/u8:2 Not tainted 5.7.0-rc1+ #532 [ 40.589299][ T146] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 40.590469][ T146] Workqueue: netns cleanup_net [ 40.591045][ T146] RIP: 0010:macvlan_device_event+0x4e2/0x900 [macvlan] [ 40.591905][ T146] Code: 00 00 00 00 00 fc ff df 80 3c 06 00 0f 85 45 02 00 00 48 89 da 48 b8 00 00 00 00 00 fc ff d2 [ 40.594126][ T146] RSP: 0018:ffff88806116f4a0 EFLAGS: 00010246 [ 40.594783][ T146] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000 [ 40.595653][ T146] RDX: 0000000000000000 RSI: ffff88806547ddd8 RDI: ffff8880540f1360 [ 40.596495][ T146] RBP: ffff88804011a808 R08: fffffbfff4fb8421 R09: fffffbfff4fb8421 [ 40.597377][ T146] R10: ffffffffa7dc2107 R11: 0000000000000000 R12: 0000000000000008 [ 40.598186][ T146] R13: ffff88804011a000 R14: ffff8880540f1000 R15: 1ffff1100c22de9a [ 40.599012][ T146] FS: 0000000000000000(0000) GS:ffff888067800000(0000) knlGS:0000000000000000 [ 40.600004][ T146] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 40.600665][ T146] CR2: 00005572d3a807b8 CR3: 000000005fcf4003 CR4: 00000000000606e0 [ 40.601485][ T146] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 40.602461][ T146] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 40.603443][ T146] Call Trace: [ 40.603871][ T146] ? nf_tables_dump_setelem+0xa0/0xa0 [nf_tables] [ 40.604587][ T146] ? macvlan_uninit+0x100/0x100 [macvlan] [ 40.605212][ T146] ? __module_text_address+0x13/0x140 [ 40.605842][ T146] notifier_call_chain+0x90/0x160 [ 40.606477][ T146] dev_set_mac_address+0x28e/0x3f0 [ 40.607117][ T146] ? netdev_notify_peers+0xc0/0xc0 [ 40.607762][ T146] ? __module_text_address+0x13/0x140 [ 40.608440][ T146] ? notifier_call_chain+0x90/0x160 [ 40.609097][ T146] ? dev_set_mac_address+0x1f0/0x3f0 [ 40.609758][ T146] dev_set_mac_address+0x1f0/0x3f0 [ 40.610402][ T146] ? __local_bh_enable_ip+0xe9/0x1b0 [ 40.611071][ T146] ? bond_hw_addr_flush+0x77/0x100 [bonding] [ 40.611823][ T146] ? netdev_notify_peers+0xc0/0xc0 [ 40.612461][ T146] ? bond_hw_addr_flush+0x77/0x100 [bonding] [ 40.613213][ T146] ? bond_hw_addr_flush+0x77/0x100 [bonding] [ 40.613963][ T146] ? __local_bh_enable_ip+0xe9/0x1b0 [ 40.614631][ T146] ? bond_time_in_interval.isra.31+0x90/0x90 [bonding] [ 40.615484][ T146] ? __bond_release_one+0x9f0/0x12c0 [bonding] [ 40.616230][ T146] __bond_release_one+0x9f0/0x12c0 [bonding] [ 40.616949][ T146] ? bond_enslave+0x47c0/0x47c0 [bonding] [ 40.617642][ T146] ? lock_downgrade+0x730/0x730 [ 40.618218][ T146] ? check_flags.part.42+0x450/0x450 [ 40.618850][ T146] ? __mutex_unlock_slowpath+0xd0/0x670 [ 40.619519][ T146] ? trace_hardirqs_on+0x30/0x180 [ 40.620117][ T146] ? wait_for_completion+0x250/0x250 [ 40.620754][ T146] bond_netdev_event+0x822/0x970 [bonding] [ 40.621460][ T146] ? __module_text_address+0x13/0x140 [ 40.622097][ T146] notifier_call_chain+0x90/0x160 [ 40.622806][ T146] rollback_registered_many+0x660/0xcf0 [ 40.623522][ T146] ? netif_set_real_num_tx_queues+0x780/0x780 [ 40.624290][ T146] ? notifier_call_chain+0x90/0x160 [ 40.624957][ T146] ? netdev_upper_dev_unlink+0x114/0x180 [ 40.625686][ T146] ? __netdev_adjacent_dev_unlink_neighbour+0x30/0x30 [ 40.626421][ T146] ? mutex_is_locked+0x13/0x50 [ 40.627016][ T146] ? unregister_netdevice_queue+0xf2/0x240 [ 40.627663][ T146] unregister_netdevice_many.part.134+0x13/0x1b0 [ 40.628362][ T146] default_device_exit_batch+0x2d9/0x390 [ 40.628987][ T146] ? unregister_netdevice_many+0x40/0x40 [ 40.629615][ T146] ? dev_change_net_namespace+0xcb0/0xcb0 [ 40.630279][ T146] ? prepare_to_wait_exclusive+0x2e0/0x2e0 [ 40.630943][ T146] ? ops_exit_list.isra.9+0x97/0x140 [ 40.631554][ T146] cleanup_net+0x441/0x890 [ ... ] Fixes: e289fd28176b ("macvlan: fix the problem when mac address changes for passthru mode") Reported-by: syzbot+5035b1f9dc7ea4558d5a@syzkaller.appspotmail.com Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-21e1000: remove unneeded conversion to boolJason Yan
The '==' expression itself is bool, no need to convert it to bool again. This fixes the following coccicheck warning: drivers/net/ethernet/intel/e1000/e1000_main.c:1479:44-49: WARNING: conversion to bool not needed here Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-21i40e: Remove unneeded conversion to boolJason Yan
The '==' expression itself is bool, no need to convert it to bool again. This fixes the following coccicheck warning: drivers/net/ethernet/intel/i40e/i40e_main.c:1614:52-57: WARNING: conversion to bool not needed here drivers/net/ethernet/intel/i40e/i40e_main.c:11439:52-57: WARNING: conversion to bool not needed here Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-20net/mlx5e: Get the latest values from counters in switchdev modeZhu Yanjun
In the switchdev mode, when running "cat /sys/class/net/NIC/statistics/tx_packets", the ppcnt register is accessed to get the latest values. But currently this command can not get the correct values from ppcnt. From firmware manual, before getting the 802_3 counters, the 802_3 data layout should be set to the ppcnt register. When the command "cat /sys/class/net/NIC/statistics/tx_packets" is run, before updating 802_3 data layout with ppcnt register, the monitor counters are tested. The test result will decide the 802_3 data layout is updated or not. Actually the monitor counters do not support to monitor rx/tx stats of 802_3 in switchdev mode. So the rx/tx counters change will not trigger monitor counters. So the 802_3 data layout will not be updated in ppcnt register. Finally this command can not get the latest values from ppcnt register with 802_3 data layout. Fixes: 5c7e8bbb0257 ("net/mlx5e: Use monitor counters for update stats") Signed-off-by: Zhu Yanjun <yanjunz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-04-20net/mlx5: Kconfig: convert imply usage to weak dependencySaeed Mahameed
MLX5_CORE uses the 'imply' keyword to depend on VXLAN, PTP_1588_CLOCK, MLXFW and PCI_HYPERV_INTERFACE. This was useful to force vxlan, ptp, etc.. to be reachable to mlx5 regardless of their config states. Due to the changes in the cited commit below, the semantics of 'imply' was changed to not force any restriction on the implied config. As a result of this change, the compilation of MLX5_CORE=y and VXLAN=m would result in undefined references, as VXLAN now would stay as 'm'. To fix this we change MLX5_CORE to have a weak dependency on these modules/configs and make sure they are reachable, by adding: depend on symbol || !symbol. For example: VXLAN=m MLX5_CORE=y, this will force MLX5_CORE to m Fixes: def2fbffe62c ("kconfig: allow symbols implied by y to become m") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Cc: Masahiro Yamada <masahiroy@kernel.org> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: Arnd Bergmann <arnd@arndb.de> Reported-by: Randy Dunlap <rdunlap@infradead.org>
2020-04-20net/mlx5e: Don't trigger IRQ multiple times on XSK wakeup to avoid WQ overrunsMaxim Mikityanskiy
XSK wakeup function triggers NAPI by posting a NOP WQE to a special XSK ICOSQ. When the application floods the driver with wakeup requests by calling sendto() in a certain pattern that ends up in mlx5e_trigger_irq, the XSK ICOSQ may overflow. Multiple NOPs are not required and won't accelerate the process, so avoid posting a second NOP if there is one already on the way. This way we also avoid increasing the queue size (which might not help anyway). Fixes: db05815b36cb ("net/mlx5e: Add XSK zero-copy support") Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-04-20net/mlx5: CT: Change idr to xarray to protect parallel tuple id allocationPaul Blakey
After allowing parallel tuple insertion, we get the following trace: [ 5505.142249] ------------[ cut here ]------------ [ 5505.148155] WARNING: CPU: 21 PID: 13313 at lib/radix-tree.c:581 delete_node+0x16c/0x180 [ 5505.295553] CPU: 21 PID: 13313 Comm: kworker/u50:22 Tainted: G OE 5.6.0+ #78 [ 5505.304824] Hardware name: Supermicro Super Server/X10DRT-P, BIOS 2.0b 03/30/2017 [ 5505.313740] Workqueue: nf_flow_table_offload flow_offload_work_handler [nf_flow_table] [ 5505.323257] RIP: 0010:delete_node+0x16c/0x180 [ 5505.349862] RSP: 0018:ffffb19184eb7b30 EFLAGS: 00010282 [ 5505.356785] RAX: 0000000000000000 RBX: ffff904ac95b86d8 RCX: ffff904b6f938838 [ 5505.365190] RDX: 0000000000000000 RSI: ffff904ac954b908 RDI: ffff904ac954b920 [ 5505.373628] RBP: ffff904b4ac13060 R08: 0000000000000001 R09: 0000000000000000 [ 5505.382155] R10: 0000000000000000 R11: 0000000000000040 R12: 0000000000000000 [ 5505.390527] R13: ffffb19184eb7bfc R14: ffff904b6bef5800 R15: ffff90482c1203c0 [ 5505.399246] FS: 0000000000000000(0000) GS:ffff904c2fc80000(0000) knlGS:0000000000000000 [ 5505.408621] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 5505.415739] CR2: 00007f5d27006010 CR3: 0000000058c10006 CR4: 00000000001626e0 [ 5505.424547] Call Trace: [ 5505.428429] idr_alloc_u32+0x7b/0xc0 [ 5505.433803] mlx5_tc_ct_entry_add_rule+0xbf/0x950 [mlx5_core] [ 5505.441354] ? mlx5_fc_create+0x23c/0x370 [mlx5_core] [ 5505.448225] mlx5_tc_ct_block_flow_offload+0x874/0x10b0 [mlx5_core] [ 5505.456278] ? mlx5_tc_ct_block_flow_offload+0x63d/0x10b0 [mlx5_core] [ 5505.464532] nf_flow_offload_tuple.isra.21+0xc5/0x140 [nf_flow_table] [ 5505.472286] ? __kmalloc+0x217/0x2f0 [ 5505.477093] ? flow_rule_alloc+0x1c/0x30 [ 5505.482117] flow_offload_work_handler+0x1d0/0x290 [nf_flow_table] [ 5505.489674] ? process_one_work+0x17c/0x580 [ 5505.494922] process_one_work+0x202/0x580 [ 5505.500082] ? process_one_work+0x17c/0x580 [ 5505.505696] worker_thread+0x4c/0x3f0 [ 5505.510458] kthread+0x103/0x140 [ 5505.514989] ? process_one_work+0x580/0x580 [ 5505.520616] ? kthread_bind+0x10/0x10 [ 5505.525837] ret_from_fork+0x3a/0x50 [ 5505.570841] ---[ end trace 07995de9c56d6831 ]--- This happens from parallel deletes/adds to idr, as idr isn't protected. Fix that by using xarray as the tuple_ids allocator instead of idr. Fixes: 7da182a998d6 ("netfilter: flowtable: Use work entry per offload command") Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-04-20net/mlx5: Fix failing fw tracer allocation on s390Niklas Schnelle
On s390 FORCE_MAX_ZONEORDER is 9 instead of 11, thus a larger kzalloc() allocation as done for the firmware tracer will always fail. Looking at mlx5_fw_tracer_save_trace(), it is actually the driver itself that copies the debug data into the trace array and there is no need for the allocation to be contiguous in physical memory. We can therefor use kvzalloc() instead of kzalloc() and get rid of the large contiguous allcoation. Fixes: f53aaa31cce7 ("net/mlx5: FW tracer, implement tracer logic") Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-04-20team: fix hang in team_mode_get()Taehee Yoo
When team mode is changed or set, the team_mode_get() is called to check whether the mode module is inserted or not. If the mode module is not inserted, it calls the request_module(). In the request_module(), it creates a child process, which is the "modprobe" process and waits for the done of the child process. At this point, the following locks were used. down_read(&cb_lock()); by genl_rcv() genl_lock(); by genl_rcv_msc() rtnl_lock(); by team_nl_cmd_options_set() mutex_lock(&team->lock); by team_nl_team_get() Concurrently, the team module could be removed by rmmod or "modprobe -r" The __exit function of team module is team_module_exit(), which calls team_nl_fini() and it tries to acquire following locks. down_write(&cb_lock); genl_lock(); Because of the genl_lock() and cb_lock, this process can't be finished earlier than request_module() routine. The problem secenario. CPU0 CPU1 team_mode_get request_module() modprobe -r team_mode_roundrobin team <--(B) modprobe team <--(A) team_mode_roundrobin By request_module(), the "modprobe team_mode_roundrobin" command will be executed. At this point, the modprobe process will decide that the team module should be inserted before team_mode_roundrobin. Because the team module is being removed. By the module infrastructure, the same module insert/remove operations can't be executed concurrently. So, (A) waits for (B) but (B) also waits for (A) because of locks. So that the hang occurs at this point. Test commands: while : do teamd -d & killall teamd & modprobe -rv team_mode_roundrobin & done The approach of this patch is to hold the reference count of the team module if the team module is compiled as a module. If the reference count of the team module is not zero while request_module() is being called, the team module will not be removed at that moment. So that the above scenario could not occur. Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-20cxgb4: fix large delays in PTP synchronizationRahul Lakkireddy
Fetching PTP sync information from mailbox is slow and can take up to 10 milliseconds. Reduce this unnecessary delay by directly reading the information from the corresponding registers. Fixes: 9c33e4208bce ("cxgb4: Add PTP Hardware Clock (PHC) support") Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com> Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-20net: stmmac: dwmac-meson8b: Add missing boundary to RGMII TX clock arrayMarc Zyngier
Running with KASAN on a VIM3L systems leads to the following splat when probing the Ethernet device: ================================================================== BUG: KASAN: global-out-of-bounds in _get_maxdiv+0x74/0xd8 Read of size 4 at addr ffffa000090615f4 by task systemd-udevd/139 CPU: 1 PID: 139 Comm: systemd-udevd Tainted: G E 5.7.0-rc1-00101-g8624b7577b9c #781 Hardware name: amlogic w400/w400, BIOS 2020.01-rc5 03/12/2020 Call trace: dump_backtrace+0x0/0x2a0 show_stack+0x20/0x30 dump_stack+0xec/0x148 print_address_description.isra.12+0x70/0x35c __kasan_report+0xfc/0x1d4 kasan_report+0x4c/0x68 __asan_load4+0x9c/0xd8 _get_maxdiv+0x74/0xd8 clk_divider_bestdiv+0x74/0x5e0 clk_divider_round_rate+0x80/0x1a8 clk_core_determine_round_nolock.part.9+0x9c/0xd0 clk_core_round_rate_nolock+0xf0/0x108 clk_hw_round_rate+0xac/0xf0 clk_factor_round_rate+0xb8/0xd0 clk_core_determine_round_nolock.part.9+0x9c/0xd0 clk_core_round_rate_nolock+0xf0/0x108 clk_core_round_rate_nolock+0xbc/0x108 clk_core_set_rate_nolock+0xc4/0x2e8 clk_set_rate+0x58/0xe0 meson8b_dwmac_probe+0x588/0x72c [dwmac_meson8b] platform_drv_probe+0x78/0xd8 really_probe+0x158/0x610 driver_probe_device+0x140/0x1b0 device_driver_attach+0xa4/0xb0 __driver_attach+0xcc/0x1c8 bus_for_each_dev+0xf4/0x168 driver_attach+0x3c/0x50 bus_add_driver+0x238/0x2e8 driver_register+0xc8/0x1e8 __platform_driver_register+0x88/0x98 meson8b_dwmac_driver_init+0x28/0x1000 [dwmac_meson8b] do_one_initcall+0xa8/0x328 do_init_module+0xe8/0x368 load_module+0x3300/0x36b0 __do_sys_finit_module+0x120/0x1a8 __arm64_sys_finit_module+0x4c/0x60 el0_svc_common.constprop.2+0xe4/0x268 do_el0_svc+0x98/0xa8 el0_svc+0x24/0x68 el0_sync_handler+0x12c/0x318 el0_sync+0x158/0x180 The buggy address belongs to the variable: div_table.63646+0x34/0xfffffffffffffa40 [dwmac_meson8b] Memory state around the buggy address: ffffa00009061480: fa fa fa fa 00 00 00 01 fa fa fa fa 00 00 00 00 ffffa00009061500: 05 fa fa fa fa fa fa fa 00 04 fa fa fa fa fa fa >ffffa00009061580: 00 03 fa fa fa fa fa fa 00 00 00 00 00 00 fa fa ^ ffffa00009061600: fa fa fa fa 00 01 fa fa fa fa fa fa 01 fa fa fa ffffa00009061680: fa fa fa fa 00 01 fa fa fa fa fa fa 04 fa fa fa ================================================================== Digging into this indeed shows that the clock divider array is lacking a final fence, and that the clock subsystems goes in the weeds. Oh well. Let's add the empty structure that indicates the end of the array. Fixes: bd6f48546b9c ("net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs") Signed-off-by: Marc Zyngier <maz@kernel.org> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-20net: systemport: Omit superfluous error message in bcm_sysport_probe()Tang Bin
In the function bcm_sysport_probe(), when get irq failed, the function platform_get_irq() logs an error message, so remove redundant message here. Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-18net/mlx4_en: avoid indirect call in TX completionEric Dumazet
Commit 9ecc2d86171a ("net/mlx4_en: add xdp forwarding and data write support") brought another indirect call in fast path. Use INDIRECT_CALL_2() helper to avoid the cost of the indirect call when/if CONFIG_RETPOLINE=y Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tariq Toukan <tariqt@mellanox.com> Cc: Willem de Bruijn <willemb@google.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-18net: stmmac: Fix sub-second incrementJulien Beraud
In fine adjustement mode, which is the current default, the sub-second increment register is the number of nanoseconds that will be added to the clock when the accumulator overflows. At each clock cycle, the value of the addend register is added to the accumulator. Currently, we use 20ns = 1e09ns / 50MHz as this value whatever the frequency of the ptp clock actually is. The adjustment is then done on the addend register, only incrementing every X clock cycles X being the ratio between 50MHz and ptp_clock_rate (addend = 2^32 * 50MHz/ptp_clock_rate). This causes the following issues : - In case the frequency of the ptp clock is inferior or equal to 50MHz, the addend value calculation will overflow and the default addend value will be set to 0, causing the clock to not work at all. (For instance, for ptp_clock_rate = 50MHz, addend = 2^32). - The resolution of the timestamping clock is limited to 20ns while it is not needed, thus limiting the accuracy of the timestamping to 20ns. Fix this by setting sub-second increment to 2e09ns / ptp_clock_rate. It will allow to reach the minimum possible frequency for ptp_clk_ref, which is 5MHz for GMII 1000Mps Full-Duplex by setting the sub-second-increment to a higher value. For instance, for 25MHz, it gives ssinc = 80ns and default_addend = 2^31. It will also allow to use a lower value for sub-second-increment, thus improving the timestamping accuracy with frequencies higher than 100MHz, for instance, for 200MHz, ssinc = 10ns and default_addend = 2^31. v1->v2: - Remove modifications to the calculation of default addend, which broke compatibility with clock frequencies for which 2000000000 / ptp_clk_freq is not an integer. - Modify description according to discussions. Signed-off-by: Julien Beraud <julien.beraud@orolia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-18net: stmmac: fix enabling socfpga's ptp_ref_clockJulien Beraud
There are 2 registers to write to enable a ptp ref clock coming from the fpga. One that enables the usage of the clock from the fpga for emac0 and emac1 as a ptp ref clock, and the other to allow signals from the fpga to reach emac0 and emac1. Currently, if the dwmac-socfpga has phymode set to PHY_INTERFACE_MODE_MII, PHY_INTERFACE_MODE_GMII, or PHY_INTERFACE_MODE_SGMII, both registers will be written and the ptp ref clock will be set as coming from the fpga. Separate the 2 register writes to only enable signals from the fpga to reach emac0 or emac1 when ptp ref clock is not coming from the fpga. Signed-off-by: Julien Beraud <julien.beraud@orolia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-18wimax/i2400m: Fix potential urb refcnt leakXiyu Yang
i2400mu_bus_bm_wait_for_ack() invokes usb_get_urb(), which increases the refcount of the "notif_urb". When i2400mu_bus_bm_wait_for_ack() returns, local variable "notif_urb" becomes invalid, so the refcount should be decreased to keep refcount balanced. The issue happens in all paths of i2400mu_bus_bm_wait_for_ack(), which forget to decrease the refcnt increased by usb_get_urb(), causing a refcnt leak. Fix this issue by calling usb_put_urb() before the i2400mu_bus_bm_wait_for_ack() returns. Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-16Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds
Pull networking fixes from David Miller: 1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel. 2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet. 3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing. 4) Adjust icmp6 message source address selection when routes have a preferred source address set, from Tim Stallard. 5) Be sure to validate HSR protocol version when creating new links, from Taehee Yoo. 6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in non-initial namespaces, from Michael Weiß. 7) Missing release firmware call in mlx5, from Eran Ben Elisha. 8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from Taehee Yoo. 9) Fix pause frame negotiation in marvell phy driver, from Clemens Gruber. 10) Record RX queue early enough in tun packet paths such that XDP programs will see the correct RX queue index, from Gilberto Bertin. 11) Fix double unlock in mptcp, from Florian Westphal. 12) Fix offset overflow in ARM bpf JIT, from Luke Nelson. 13) marvell10g needs to soft reset PHY when coming out of low power mode, from Russell King. 14) Fix MTU setting regression in stmmac for some chip types, from Florian Fainelli. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits) amd-xgbe: Use __napi_schedule() in BH context mISDN: make dmril and dmrim static net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode tipc: fix incorrect increasing of link window Documentation: Fix tcp_challenge_ack_limit default value net: tulip: make early_486_chipsets static dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400 ipv6: remove redundant assignment to variable err net/rds: Use ERR_PTR for rds_message_alloc_sgs() net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge selftests/bpf: Check for correct program attach/detach in xdp_attach test libbpf: Fix type of old_fd in bpf_xdp_set_link_opts libbpf: Always specify expected_attach_type on program load if supported xsk: Add missing check on user supplied headroom size mac80211: fix channel switch trigger from unknown mesh peer mac80211: fix race in ieee80211_register_hw() net: marvell10g: soft-reset the PHY when coming out of low power net: marvell10g: report firmware version net/cxgb4: Check the return from t4_query_params properly ...
2020-04-16amd-xgbe: Use __napi_schedule() in BH contextSebastian Andrzej Siewior
The driver uses __napi_schedule_irqoff() which is fine as long as it is invoked with disabled interrupts by everybody. Since the commit mentioned below the driver may invoke xgbe_isr_task() in tasklet/softirq context. This may lead to list corruption if another driver uses __napi_schedule_irqoff() in IRQ context. Use __napi_schedule() which safe to use from IRQ and softirq context. Fixes: 85b85c853401d ("amd-xgbe: Re-issue interrupt if interrupt status not cleared") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-16net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizesFlorian Fainelli
After commit bfcb813203e619a8960a819bf533ad2a108d8105 ("net: dsa: configure the MTU for switch ports") my Lamobo R1 platform which uses an allwinner,sun7i-a20-gmac compatible Ethernet MAC started to fail by rejecting a MTU of 1536. The reason for that is that the DMA capabilities are not readable on this version of the IP, and there is also no 'tx-fifo-depth' property being provided in Device Tree. The property is documented as optional, and is not provided. Chen-Yu indicated that the FIFO sizes are 4KB for TX and 16KB for RX, so provide these values through platform data as an immediate fix until various Device Tree sources get updated accordingly. Fixes: eaf4fac47807 ("net: stmmac: Do not accept invalid MTU values") Suggested-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-16net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware modeDENG Qingfang
In VLAN-unaware mode, the Egress Tag (EG_TAG) field in Port VLAN Control register must be set to Consistent to let tagged frames pass through as is, otherwise their tags will be stripped. Fixes: 83163f7dca56 ("net: dsa: mediatek: add VLAN support for MT7530") Signed-off-by: DENG Qingfang <dqfext@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: René van Dorst <opensource@vdorst.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-15net: tulip: make early_486_chipsets staticJason Yan
Fix the following sparse warning: drivers/net/ethernet/dec/tulip/tulip_core.c:1280:28: warning: symbol 'early_486_chipsets' was not declared. Should it be static? Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-15net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridgeVladimir Oltean
To rehash a previous explanation given in commit 1c44ce560b4d ("net: mscc: ocelot: fix vlan_filtering when enslaving to bridge before link is up"), the switch driver operates the in a mode where a single VLAN can be transmitted as untagged on a particular egress port. That is the "native VLAN on trunk port" use case. The configuration for this native VLAN is driven in 2 ways: - Set the egress port rewriter to strip the VLAN tag for the native VID (as it is egress-untagged, after all). - Configure the ingress port to drop untagged and priority-tagged traffic, if there is no native VLAN. The intention of this setting is that a trunk port with no native VLAN should not accept untagged traffic. Since both of the above configurations for the native VLAN should only be done if VLAN awareness is requested, they are actually done from the ocelot_port_vlan_filtering function, after the basic procedure of toggling the VLAN awareness flag of the port. But there's a problem with that simplistic approach: we are trying to juggle with 2 independent variables from a single function: - Native VLAN of the port - its value is held in port->vid. - VLAN awareness state of the port - currently there are some issues here, more on that later*. The actual problem can be seen when enslaving the switch ports to a VLAN filtering bridge: 0. The driver configures a pvid of zero for each port, when in standalone mode. While the bridge configures a default_pvid of 1 for each port that gets added as a slave to it. 1. The bridge calls ocelot_port_vlan_filtering with vlan_aware=true. The VLAN-filtering-dependent portion of the native VLAN configuration is done, considering that the native VLAN is 0. 2. The bridge calls ocelot_vlan_add with vid=1, pvid=true, untagged=true. The native VLAN changes to 1 (change which gets propagated to hardware). 3. ??? - nobody calls ocelot_port_vlan_filtering again, to reapply the VLAN-filtering-dependent portion of the native VLAN configuration, for the new native VLAN of 1. One can notice that after toggling "ip link set dev br0 type bridge vlan_filtering 0 && ip link set dev br0 type bridge vlan_filtering 1", the new native VLAN finally makes it through and untagged traffic finally starts flowing again. But obviously that shouldn't be needed. So it is clear that 2 independent variables need to both re-trigger the native VLAN configuration. So we introduce the second variable as ocelot_port->vlan_aware. *Actually both the DSA Felix driver and the Ocelot driver already had each its own variable: - Ocelot: ocelot_port_private->vlan_aware - Felix: dsa_port->vlan_filtering but the common Ocelot library needs to work with a single, common, variable, so there is some refactoring done to move the vlan_aware property from the private structure into the common ocelot_port structure. Fixes: 97bb69e1e36e ("net: mscc: ocelot: break apart ocelot_vlan_port_apply") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-15Merge tag 'mac80211-for-net-2020-04-15' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== A couple of fixes: * FTM responder policy netlink validation fix (but the only user validates again later) * kernel-doc fixes * a fix for a race in mac80211 radio registration vs. userspace * a mesh channel switch fix * a fix for a syzbot reported kasprintf() issue ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-14net: marvell10g: soft-reset the PHY when coming out of low powerRussell King
Soft-reset the PHY when coming out of low power mode, which seems to be necessary with firmware versions 0.3.3.0 and 0.3.10.0. This depends on ("net: marvell10g: report firmware version") Fixes: c9cc1c815d36 ("net: phy: marvell10g: place in powersave mode at probe") Reported-by: Matteo Croce <mcroce@redhat.com> Tested-by: Matteo Croce <mcroce@redhat.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-14net: marvell10g: report firmware versionRussell King
Report the firmware version when probing the PHY to allow issues attributable to firmware to be diagnosed. Tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-14net/cxgb4: Check the return from t4_query_params properlyJason Gunthorpe
Positive return values are also failures that don't set val, although this probably can't happen. Fixes gcc 10 warning: drivers/net/ethernet/chelsio/cxgb4/t4_hw.c: In function ‘t4_phy_fw_ver’: drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:3747:14: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized] 3747 | *phy_fw_ver = val; Fixes: 01b6961410b7 ("cxgb4: Add PHY firmware support for T420-BT cards") Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-14net: stmmac: socfpga: Allow all RGMII modesAtsushi Nemoto
Allow all the RGMII modes to be used. (Not only "rgmii", "rgmii-id" but "rgmii-txid", "rgmii-rxid") Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-14net: dsa: mv88e6xxx: Configure MAC when using fixed linkAndrew Lunn
The 88e6185 is reporting it has detected a PHY, when a port is connected to an SFP. As a result, the fixed-phy configuration is not being applied. That then breaks packet transfer, since the port is reported as being down. Add additional conditions to check the interface mode, and if it is fixed always configure the port on link up/down, independent of the PPU status. Fixes: 30c4a5b0aad8 ("net: mv88e6xxx: use resolved link config in mac_link_up()") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-14ionic: fix unused assignmentShannon Nelson
Remove an unused initialized value. Fixes: 7e4d47596b68 ("ionic: replay filters after fw upgrade") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-14ionic: add dynamic_debug headerShannon Nelson
Add the appropriate header for using dynamic_hex_dump(), which seems to be incidentally included in some configurations but not all. Fixes: 7e4d47596b68 ("ionic: replay filters after fw upgrade") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-14net: phy: micrel: use genphy_read_status for KSZ9131Atsushi Nemoto
KSZ9131 will not work with some switches due to workaround for KSZ9031 introduced in commit d2fd719bcb0e83cb39cfee22ee800f98a56eceb3 ("net/phy: micrel: Add workaround for bad autoneg"). Use genphy_read_status instead of dedicated ksz9031_read_status. Fixes: bff5b4b37372 ("net: phy: micrel: add Microchip KSZ9131 initial driver") Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-14Merge tag 'wireless-drivers-2020-04-14' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for v5.7 First set of fixes for v5.6. Fixes for a crash and for two compiler warnings. brcmfmac * fix a crash related to monitor interface ath11k * fix compiler warnings without CONFIG_THERMAL rtw88 * fix compiler warnings related to suspend and resume functions ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-14rtw88: avoid unused function warningsArnd Bergmann
The rtw88 driver defines emtpy functions with multiple indirections but gets one of these wrong: drivers/net/wireless/realtek/rtw88/pci.c:1347:12: error: 'rtw_pci_resume' defined but not used [-Werror=unused-function] 1347 | static int rtw_pci_resume(struct device *dev) | ^~~~~~~~~~~~~~ drivers/net/wireless/realtek/rtw88/pci.c:1342:12: error: 'rtw_pci_suspend' defined but not used [-Werror=unused-function] 1342 | static int rtw_pci_suspend(struct device *dev) Better simplify it to rely on the conditional reference in SIMPLE_DEV_PM_OPS(), and mark the functions as __maybe_unused to avoid warning about it. I'm not sure if these are needed at all given that the functions don't do anything, but they were only recently added. Fixes: 44bc17f7f5b3 ("rtw88: support wowlan feature for 8822c") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200408185413.218643-1-arnd@arndb.de
2020-04-14mac80211_hwsim: Use kstrndup() in place of kasprintf()Tuomas Tynkkynen
syzbot reports a warning: precision 33020 too large WARNING: CPU: 0 PID: 9618 at lib/vsprintf.c:2471 set_precision+0x150/0x180 lib/vsprintf.c:2471 vsnprintf+0xa7b/0x19a0 lib/vsprintf.c:2547 kvasprintf+0xb2/0x170 lib/kasprintf.c:22 kasprintf+0xbb/0xf0 lib/kasprintf.c:59 hwsim_del_radio_nl+0x63a/0x7e0 drivers/net/wireless/mac80211_hwsim.c:3625 genl_family_rcv_msg_doit net/netlink/genetlink.c:672 [inline] ... entry_SYSCALL_64_after_hwframe+0x49/0xbe Thus it seems that kasprintf() with "%.*s" format can not be used for duplicating a string with arbitrary length. Replace it with kstrndup(). Note that later this string is limited to NL80211_WIPHY_NAME_MAXLEN == 64, but the code is simpler this way. Reported-by: syzbot+6693adf1698864d21734@syzkaller.appspotmail.com Reported-by: syzbot+a4aee3f42d7584d76761@syzkaller.appspotmail.com Cc: stable@kernel.org Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> Link: https://lore.kernel.org/r/20200410123257.14559-1-tuomas.tynkkynen@iki.fi [johannes: add note about length limit] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-04-12net: mvneta: Fix a typoChristophe JAILLET
s/mvmeta/mvneta/ Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-12net: tun: record RX queue in skb before do_xdp_generic()Gilberto Bertin
This allows netif_receive_generic_xdp() to correctly determine the RX queue from which the skb is coming, so that the context passed to the XDP program will contain the correct RX queue index. Signed-off-by: Gilberto Bertin <me@jibi.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-12net: ethernet: ti: Add missing '\n' in log messagesChristophe JAILLET
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'. Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-04-12soc: qcom: ipa: Add a missing '\n' in a log messageChristophe JAILLET
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'. Fixes: a646d6ec9098 ("soc: qcom: ipa: modem and microcontroller") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-04-12net: neterion: remove redundant assignment to variable tmp64Colin Ian King
The variable tmp64 is being initialized with a value that is never read and it is being updated later with a new value. The initialization is redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-04-11net: phy: marvell: Fix pause frame negotiationClemens Gruber
The negotiation of flow control / pause frame modes was broken since commit fcf1f59afc67 ("net: phy: marvell: rearrange to use genphy_read_lpa()") moved the setting of phydev->duplex below the phy_resolve_aneg_pause call. Due to a check of DUPLEX_FULL in that function, phydev->pause was no longer set. Fix it by moving the parsing of the status variable before the blocks dealing with the pause frames. As the Marvell 88E1510 datasheet does not specify the timing between the link status and the "Speed and Duplex Resolved" bit, we have to force the link down as long as the resolved bit is not set, to avoid reporting link up before we even have valid Speed/Duplex. Tested with a Marvell 88E1510 (RGMII to Copper/1000Base-T) Fixes: fcf1f59afc67 ("net: phy: marvell: rearrange to use genphy_read_lpa()") Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-04-09net: macsec: fix using wrong structure in macsec_changelink()Taehee Yoo
In the macsec_changelink(), "struct macsec_tx_sa tx_sc" is used to store "macsec_secy.tx_sc". But, the struct type of tx_sc is macsec_tx_sc, not macsec_tx_sa. So, the macsec_tx_sc should be used instead. Test commands: ip link add dummy0 type dummy ip link add macsec0 link dummy0 type macsec ip link set macsec0 type macsec encrypt off Splat looks like: [61119.963483][ T9335] ================================================================== [61119.964709][ T9335] BUG: KASAN: slab-out-of-bounds in macsec_changelink.part.34+0xb6/0x200 [macsec] [61119.965787][ T9335] Read of size 160 at addr ffff888020d69c68 by task ip/9335 [61119.966699][ T9335] [61119.966979][ T9335] CPU: 0 PID: 9335 Comm: ip Not tainted 5.6.0+ #503 [61119.967791][ T9335] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [61119.968914][ T9335] Call Trace: [61119.969324][ T9335] dump_stack+0x96/0xdb [61119.969809][ T9335] ? macsec_changelink.part.34+0xb6/0x200 [macsec] [61119.970554][ T9335] print_address_description.constprop.5+0x1be/0x360 [61119.971294][ T9335] ? macsec_changelink.part.34+0xb6/0x200 [macsec] [61119.971973][ T9335] ? macsec_changelink.part.34+0xb6/0x200 [macsec] [61119.972703][ T9335] __kasan_report+0x12a/0x170 [61119.973323][ T9335] ? macsec_changelink.part.34+0xb6/0x200 [macsec] [61119.973942][ T9335] kasan_report+0xe/0x20 [61119.974397][ T9335] check_memory_region+0x149/0x1a0 [61119.974866][ T9335] memcpy+0x1f/0x50 [61119.975209][ T9335] macsec_changelink.part.34+0xb6/0x200 [macsec] [61119.975825][ T9335] ? macsec_get_stats64+0x3e0/0x3e0 [macsec] [61119.976451][ T9335] ? kernel_text_address+0x111/0x120 [61119.976990][ T9335] ? pskb_expand_head+0x25f/0xe10 [61119.977503][ T9335] ? stack_trace_save+0x82/0xb0 [61119.977986][ T9335] ? memset+0x1f/0x40 [61119.978397][ T9335] ? __nla_validate_parse+0x98/0x1ab0 [61119.978936][ T9335] ? macsec_alloc_tfm+0x90/0x90 [macsec] [61119.979511][ T9335] ? __kasan_slab_free+0x111/0x150 [61119.980021][ T9335] ? kfree+0xce/0x2f0 [61119.980700][ T9335] ? netlink_trim+0x196/0x1f0 [61119.981420][ T9335] ? nla_memcpy+0x90/0x90 [61119.982036][ T9335] ? register_lock_class+0x19e0/0x19e0 [61119.982776][ T9335] ? memcpy+0x34/0x50 [61119.983327][ T9335] __rtnl_newlink+0x922/0x1270 [ ... ] Fixes: 3cf3227a21d1 ("net: macsec: hardware offloading infrastructure") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-02 14:54:13 +0000