| Age | Commit message (Collapse) | Author |
|---|
|
The version string already contains the printk level
specifying it again results in the following message
being printed:
<6>r6040: RDC R6040 NAPI ...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In r8169 driver MTU is used to calculate receive buffer size.
Receive buffer size is used to configure hardware incoming packet filter.
For jumbo frames:
Receive buffer size = Max frame size = MTU + 14 (ethernet header) + 4
(vlan header) + 4 (ethernet checksum) = MTU + 22
Bug:
driver for all MTU up to 1536 use receive buffer size 1536
As you can see from formula, this mean all IP packets > 1536 - 22
(for vlan tagged, 1536 - 18 for not tagged) are dropped by hardware
filter.
Example:
host_good> ifconfig eth0 mtu 1536
host_r8169> ifconfig eth0 mtu 1536
host_good> ping host_r8169
Ok
host_good> ping -s 1500 host_r8169
Fail
host_good> ifconfig eth0 mtu 7000
host_r8169> ifconfig eth0 mtu 7000
host_good> ping -s 1500 host_r8169
Ok
Bonus: got rid of magic number 8
Signed-off-by: Raimonds Cicans <ray@apollo.lv>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the missing "get_xstats_size" callback for the
netlink interface, which is required if "fill_xstats" is used,
as pointed out by Patrick McHardy.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In 2.6.32-rc the new EMS USB CAN driver was contributed and added the Kconfig
entry right behind an entry of the same *vendor*. This teared the SJA1000
based driver selection into pieces.
This fix cleans up the 2.6.32-rc Kconfig files for the CAN drivers and moves
the SJA1000 and USB Kconfig portions into the belonging directories.
As there are many new CAN drivers in the queue getting this cleanup into
2.6.32-rc would massively reduce the problems for the upcoming drivers.
Thanks,
Oliver
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due commit 4b77b0a2ba27d64f58f16d8d4d48d8319dda36ff, it is not more
possible to pci_restore_state() more than once without calling
pci_save_state() in the middle.
Actually running a ethtool test on s2io makes the card inactive,
and it needs to unload/reload the module to fix.
This patch just save the state just after it restore in order to
keep the old behaviour
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 2.6.32-rc6 from wireless-testing, the following warning is emitted:
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:860 check_for_stack+0xaa/0xe0()
Hardware name: HP Pavilion dv2700 Notebook PC
ehci_hcd 0000:00:02.1: DMA-API: device driver maps memory fromstack
[addr=ffff8800b6e2bca8]
Modules linked in: <Removed>
Pid: 16378, comm: modprobe Not tainted 2.6.32-rc6-wl #244
Call Trace:
[<ffffffff81049698>] warn_slowpath_common+0x78/0xb0
[<ffffffff8104972c>] warn_slowpath_fmt+0x3c/0x40
[<ffffffff811ae52a>] check_for_stack+0xaa/0xe0
[<ffffffff811afc8d>] debug_dma_map_page+0xfd/0x170
[<ffffffffa006297a>] usb_hcd_submit_urb+0x3da/0x9c0 [usbcore]
[<ffffffff81076e6f>] ? lockdep_init_map+0x5f/0x5d0
[<ffffffffa0063365>] usb_submit_urb+0xe5/0x260 [usbcore]
[<ffffffffa0064b7e>] usb_start_wait_urb+0x5e/0xf0 [usbcore]
[<ffffffffa0063943>] ? usb_init_urb+0x23/0x40 [usbcore]
[<ffffffffa0064cd4>] usb_bulk_msg+0xc4/0x150 [usbcore]
[<ffffffffa0441a91>] T.719+0x31/0x40 [p54usb]
[<ffffffffa0441acf>] p54u_upload_firmware_3887+0x2f/0x490 [p54usb]
[<ffffffffa049c667>] ? p54_parse_firmware+0x427/0x450 [p54common]
<Rest of traceback removed>
---[ end trace f77df0316ddad3de ]---
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This reverts commit b8ecd988b1670035a05035c553c08331214d6603.
Due to poor API call balancing by me, this commit not only broke ipw2200
if it can't find it's firmware, it broke ipw2100 basically anytime you
removed the module. At this point in the cycle, let's just put it back
to a sane state and try again next time...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Turn on RTS/CTS for HT to prevent uCode TX fifo underrun
This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.
The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.
When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.
By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.
For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Configuration of wake-on-lan for unicast, multicast, broadcast, physical
activity was not working. Kernel panic issue was there when user tries to
disable WOL. Fixed them.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Due to a missing header include, sparse generates the following warnings:
CHECK drivers/net/wireless/rtl818x/rtl8187_rfkill.c
warning: symbol 'rtl8187_rfkill_init' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_poll' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_exit' was not declared. Should it be static?
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Setup the GPIOs for the BenQ Joybook netbook.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add GPIO configuration for the Compaq CQ60 laptop
Reported-by: David Dreggors <ddreggors@jumptv.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We should not zero out the multicast hash when configuring
the operating mode, since a zero value means all multicast
frames will get dropped. Also, ath5k_mode_setup() gets
called after any reset, so the hash already set up in
configure_filter() is lost.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ops->set_tim() must be atomic, so b43 trying to acquire a mutex leads
to a kernel crash. This patch trades an easy to trigger crash in AP
mode for an unlikely race condition. According to Michael, the real
fix would be to allow set_tim() to sleep, since b43 is not the only
driver that needs to sleep in all callbacks.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Add an interface to lock/unlock an I2C bus segment
i2c-piix4: Modify code name SB900 to Hudson-2
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net/fsl_pq_mdio: add module license GPL
can: fix WARN_ON dump in net/core/rtnetlink.c:rtmsg_ifinfo()
can: should not use __dev_get_by_index() without locks
hisax: remove bad udelay call to fix build error on ARM
ipip: Fix handling of DF packets when pmtudisc is OFF
qlge: Set PCIe reset type for EEH to fundamental.
qlge: Fix early exit from mbox cmd complete wait.
ixgbe: fix traffic hangs on Tx with ioatdma loaded
ixgbe: Fix checking TFCS register for TXOFF status when DCB is enabled
ixgbe: Fix gso_max_size for 82599 when DCB is enabled
macsonic: fix crash on PowerBook 520
NET: cassini, fix lock imbalance
ems_usb: Fix byte order issues on big endian machines
be2net: Bug fix to send config commands to hardware after netdev_register
be2net: fix to set proper flow control on resume
netfilter: xt_connlimit: fix regression caused by zero family value
rt2x00: Don't queue ieee80211 work after USB removal
Revert "ipw2200: fix oops on missing firmware"
decnet: netdevice refcount leak
netfilter: nf_nat: fix NAT issue in 2.6.30.4+
...
|
|
Convert PCMCIA drivers to use the dynamic debug infrastructure, instead of
requiring manual settings of PCMCIA_DEBUG.
Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Convert PCMCIA drivers to use the dynamic debug infrastructure, instead of
requiring manual settings of PCMCIA_DEBUG.
Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Convert PCMCIA drivers to use the dynamic debug infrastructure, instead of
requiring manual settings of PCMCIA_DEBUG. Only some rare debug checks are
now hidden behind "#ifdef DEBUG" or "#if 0".
Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Use the new CIS helpers in net pcmcia drivers, which allows for
a few code cleanups.
This revision does not remove the phys_addr assignment in
3c589_cs.c -- a bug noted by Komuro <komurojun-mbn@nifty.com>
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Use pcmcia_loop_config() in a few drivers missed during the first
round. On fmvj18x_cs.c it -- strangely -- only requries us to set
conf.ConfigIndex, which is done by the core, so include an empty
loop function which returns 0 unconditionally.
CC: David S. Miller <davem@davemloft.net>
CC: David Sterba <dsterba@suse.cz>
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
For the ipwireless part: Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
A few PCMCIA network drivers can make use of values provided by the pcmcia
core, instead of tedious, independent CIS parsing.
xirc32ps_cs.c: manf_id
hostap_cs.c: multifunction count
b43/pcmcia.c: ConfigBase address and "Present"
smc91c92_cs.c: By default, mhz_setup() can use VERS_1 as it is stored
in struct pcmcia_device. Only some cards require workarounds, such as
reading out VERS_1 twice.
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
or it will taint the kernel and fail to load becuase
of_address_to_resource() is GPL only.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On older kernels, e.g. 2.6.27, a WARN_ON dump in rtmsg_ifinfo()
is thrown when the CAN device is registered due to insufficient
skb space, as reported by various users. This patch adds the
rtnl_link_ops "get_size" to fix the problem. I think this patch
is required for more recent kernels as well, even if no WARN_ON
dumps are triggered. Maybe we also need "get_xstats_size" for
the CAN xstats.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers need to be able to prevent access to an I2C bus segment
for a specific period of time. Add an interface for them to do so
without twiddling with i2c-core internals.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
This device requires a fundamental reset when recovering from EEH.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This line was accidentally left out of the previous commit #
da03945140a035a2962f7f93e359085596f20499 ("qlge: Fix firmware mailbox
command timeout.").
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ioatdma was loaded we we were unable to transmit traffic. We weren't
using the correct registers in ixgbe_update_tx_dca for 82599 systems.
Likewise in ixgbe_configure_tx() we weren't disabling the arbiter before
modifying MTQC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When DCB is enabled, the ixgbe_check_tx_hang() should check the corresponding
TC's TXOFF in TFCS based on the TC that the tx ring belongs to. Adds a
function to map from the tx_ring hw reg_idx to the correspodning TC and read
TFCS accordingly.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 32k gso_max_size when DCB is enabled is for 82598 only, not for 82599.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No-one seems to know where the PowerBook 500 series store their ethernet
MAC addresses. So, rather than crash, use a MAC address from the SONIC
CAM. Failing that, generate a random one.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stanse found that one error path in cas_open omits to unlock pm_mutex.
Fix that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CPC-USB is using a ARM7 core with little endian byte order. The "id" field
in can_msg needs byte order conversion from/to CPU byte order.
Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sending config commands to be2 hardware before netdev_register is
completed, is sometimes causing the async link notification to arrive
even before the driver is ready to handle it. The commands for vlan
config and flow control settings can infact wait till be_open.
This patch takes care of that.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If be2 goes into suspend after a user changes the flow control settings,
we are not programming them back after resume. This patch takes care of it.
We now get the flow control settings before going to suspend mode and
then apply them during resume.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
This prevents the rt2x00 driver from queueing ieee80211 work after the
USB card has been removed, preventing a kernel panic.
Signed-off-by: Sean Cross <sean@chumby.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This reverts commit e6c5fc53d0f44a772398402ee8a1879818e42b4e.
Based on this regression report:
Date: Thu, 05 Nov 2009 15:59:16 +0100
From: Holger Schurig <holgerschurig@gmail.com>
To: linux-wireless@vger.kernel.org
Subject: BUG: oops when "rmmod ipw2200"
This happened on wireless-testing v2.6.32-rc6-41575-g5e68bfb. I
modprobed ipw2200, put it into monitor mode, used tshark a while to
monitor, then I stopped tshark, "ifconfig eth2 down" and finally
"rmmod ipw2200", and voila:
[ 917.189620] ------------[ cut here ]------------
[ 917.189717] kernel BUG at net/wireless/core.c:543!
[ 917.189805] invalid opcode: 0000 [#1] PREEMPT SMP
[ 917.190002] last sysfs file: /sys/devices/pci0000:00/0000:00:1e.0/0000:02:0d.0/firmware/0000:02:0d.0/loading
[ 917.190136] Modules linked in: lib80211_crypt_wep ipw2200(-) libipw lib80211 ath5k mac80211 ath cfg80211 psmouse uhci_hcd
[ 917.190680]
[ 917.190759] Pid: 1763, comm: rmmod Not tainted (2.6.32-rc6-wl #26) Amilo M1425
[ 917.190886] EIP: 0060:[<f8accf34>] EFLAGS: 00010202 CPU: 0
[ 917.190992] EIP is at wiphy_unregister+0xd3/0x175 [cfg80211]
[ 917.191083] EAX: f601d4c4 EBX: 00000000 ECX: 00000000 EDX: f79e8600
[ 917.191176] ESI: f601d400 EDI: f95b4350 EBP: f6009eb4 ESP: f6009e8c
[ 917.191269] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 917.191360] Process rmmod (pid: 1763, ti=f6008000 task=f79e8130 task.ti=f6008000)
[ 917.191486] Stack:
[ 917.191562] f601d5a0 f601d484 f6460e98 f6009ea0 c01407ee f6009eb8 00000246 f64604c0
[ 917.191916] <0> f6460e5c f95b4350 f6009ec0 f94fd030 f6460e98 f6009edc f95a9d4f f787bc00
[ 917.192100] <0> f787bc58 f787bc00 f95b4350 f95b4350 f6009ee8 c0207fca f787bc58 f6009ef8
[ 917.192100] Call Trace:
[ 917.192100] [<c01407ee>] ? trace_hardirqs_on+0xb/0xd
[ 917.192100] [<f94fd030>] ? unregister_ieee80211+0xe/0x27 [libipw]
[ 917.192100] [<f95a9d4f>] ? ipw_pci_remove+0x59/0x227 [ipw2200]
[ 917.192100] [<c0207fca>] ? pci_device_remove+0x19/0x39
[ 917.192100] [<c02b93a4>] ? __device_release_driver+0x59/0x9d
[ 917.192100] [<c02b944f>] ? driver_detach+0x67/0x85
[ 917.192100] [<c02b88d6>] ? bus_remove_driver+0x69/0x85
[ 917.192100] [<c02b9878>] ? driver_unregister+0x4d/0x54
[ 917.192100] [<c02081c3>] ? pci_unregister_driver+0x28/0x71
[ 917.192100] [<f95a9cf4>] ? ipw_exit+0x1c/0x1e [ipw2200]
[ 917.192100] [<c0148e2b>] ? sys_delete_module+0x192/0x1ef
[ 917.192100] [<c0162cdb>] ? remove_vma+0x52/0x58
[ 917.192100] [<c01028bb>] ? sysenter_exit+0xf/0x18
[ 917.192100] [<c0102888>] ? sysenter_do_call+0x12/0x36
[ 917.192100] Code: 74 07 e8 81 bc 8c c7 eb c8 8d 55 e0 89 f8 e8 d6 6d 66 c7 8b 45 dc 31 d2 e8 81 cc 8c c7 8d 86 c4 00 00 00 39 86 c4 00 00 00 74 04 <0f> 0b eb fe 8b 45 dc 8d 5e 0c e8 5a cc 8c c7 8b 86 94 03 00 00
[ 917.192100] EIP: [<f8accf34>] wiphy_unregister+0xd3/0x175 [cfg80211] SS:ESP 0068:f6009e8c
[ 917.203718] ---[ end trace bcaaf449945a5100 ]---
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit
3d1285b (move virtnet_remove to .devexit.text)
introduced the first reference to __devexit in struct virtio_driver
virtio_net which upset modpost ("Section mismatch in reference from the
variable virtio_net to the function .devexit.text:virtnet_remove()").
Fix this by renaming virtio_net to virtio_net_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Blame-taken-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As reported by Rick Farina (sidhayn@gmail.com), removing the RTL8187
USB stick, or unloading the driver rtl8187 using rmmod will cause a
kernel oops. There are at least two forms of the failure, (1) BUG:
Scheduling while atomic, and (2) a fatal kernel page fault. This
problem is reported in Bugzilla #14539.
This problem does not occur for kernel 2.6.31, but does for 2.6.32-rc2,
thus it is technically a regression; however, bisection did not locate
any faulty patch. The fix was found by comparing the faulty code in
rtl8187 with p54usb. My interpretation is that the handling of work
queues in mac80211 changed enough to the LEDs to be unregistered
before tasks on the work queues are cancelled. Previously, these
actions could be done in either order.
(Herton Ronaldo Krzesinski <herton@mandriva.com.br> reports that the
code is the same in 2.6.31, so this may be a candidate for 2.6.31.x.
-- JWL)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Rick Farina <sidhayn@gmail.com>
Tested-by: Rick Farina <sidhayn@gmail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
emac_irq is declared as:
static irqreturn_t emac_irq(int irq, void *dev_id)
{
struct net_device *ndev = (struct net_device *)dev_id;
struct emac_priv *priv = netdev_priv(ndev);
...
Clearly emac_irq() needs "struct net_device *" as "void *dev_id", so correct this.
Signed-off-by: Tonyliu <Bo.Liu@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Torgny Johansson <torgny.johansson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
mac80211: check interface is down before type change
cfg80211: fix NULL ptr deref
libertas if_usb: Fix crash on 64-bit machines
mac80211: fix reason code output endianness
mac80211: fix addba timer
ath9k: fix misplaced semicolon on rate control
b43: Fix DMA TX bounce buffer copying
mac80211: fix BSS leak
rt73usb.c : more ids
ipw2200: fix oops on missing firmware
gre: Fix dev_addr clobbering for gretap
sky2: set carrier off in probe
net: fix sk_forward_alloc corruption
pcnet_cs: add cis of PreMax PE-200 ethernet pcmcia card
r8169: Fix card drop incoming VLAN tagged MTU byte large jumbo frames
ibmtr: possible Read buffer overflow?
net: Fix RPF to work with policy routing
net: fix kmemcheck annotations
e1000e: rework disable K1 at 1000Mbps for 82577/82578
e1000e: config PHY via software after resets
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
The MTU throttle-down if a RNDIS device doesn't support a particular
packet size is being incorrectly logged. The attempted packet size is
being clobbered before it gets logged.
First patch; please inform if I'm doing this incorrectly. Diff'd
against latest official source as per the FAQ; forward port to current
git version is straightforward.
Signed-off-by: George Nassar <george.nassar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
On a 64-bit kernel, skb->tail is an offset, not a pointer. The libertas
usb driver passes it to usb_fill_bulk_urb() anyway, causing interesting
crashes. Fix that by using skb->data instead.
This highlights a problem with usb_fill_bulk_urb(). It doesn't notice
when dma_map_single() fails and return the error to its caller as it
should. In fact it _can't_ currently return the error, since it returns
void.
So this problem was showing up only at unmap time, after we'd already
suffered memory corruption by doing DMA to a bogus address.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The patch e43419f9:
ath9k: downgrade assert in rc.c for invalid rate
downgraded an ASSERT to a WARN_ON() but also misplaced a
semicolon at the end of the second check. What this did
was force the rate control code to always return the rate
even if we should have warned about it. Since this should
not have happened anymore anyway this fix isn't critical
as the proper rate would have been returned anyway.
Cc: stable@kernel.org
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
