summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2010-05-24rt2x00: don't use to_pci_dev in rt2x00pci_uninitializeHelmut Schaa
Don't use to_pci_dev in rt2x00pci_uninitialize to get the allocated irq as it won't work for platform devices (SoC). Instead, use the irq field that's already used everywhere else. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-05-24ath5k: consistently use rx_bufsize for RX DMABruno Randolf
We should use the same buffer size we set up for DMA also in the hardware descriptor. Previously we used common->rx_bufsize for setting up the DMA mapping, but used skb_tailroom(skb) for the size we tell to the hardware in the descriptor itself. The problem is that skb_tailroom(skb) can give us a larger value than the size we set up for DMA before. This allows the hardware to write into memory locations not set up for DMA. In practice this should rarely happen because all packets should be smaller than the maximum 802.11 packet size. On the tested platform rx_bufsize is 2528, and we allocated an skb of 2559 bytes length (including padding for cache alignment) but sbk_tailroom() was 2592. Just consistently use rx_bufsize for all RX DMA memory sizes. Also use the return value of the descriptor setup function. Cc: stable@kernel.org Signed-off-by: Bruno Randolf <br1@einfach.org> Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-05-21rndis_wlan: replace wireless_send_event with cfg80211_disconnectedJussi Kivilinna
Remove (hopefully) last use of WEXT in rndis_wlan. Replace wireless_send_event with missing cfg80211_disconnected in rndis_wlan_do_link_down_work. Reported-by: "Rogério Brito" <rbrito@ime.usp.br> Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-05-21ath9k: remove AR9003 from PCI IDs for nowLuis R. Rodriguez
We tried to squeeze as much AR9003 support into this kernel release cycle but there are a few features which are still being tested and developed. Some of these features are critical to the stable operation of AR9003 so for now disable AR9003 support all together. This will get re-enabled once all necessary features are in place but very likely will not happen for 2.6.35. Reviewed-by: Don Breslin <don.breslin@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-05-21wl1271: Fix RX data path frame lengthsJuuso Oikarinen
The current frame length used by the driver for RX frames is the SPI bus transfer length. This length has padding bytes, which do not belong to the WLAN frame. As there is no other length information in the WLAN frame except the skb length this problem caused for instance extra ESSID's to be listed at the end of scan results (IE id 0) with zero length. Fix the frame length by removing padding. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-05-21iwlwifi: fix internal scan raceReinette Chatre
It is possible for internal scan to race against itself if the device is not returning the scan results from first requests. What happens in this case is the cleanup done during the abort of the first internal scan also cleans up part of the new scan, causing it to access memory it shouldn't. Here are details: * First internal scan is triggered and scan command sent to device. * After seven seconds there is no scan results so the watchdog timer triggers a scan abort. * The scan abort succeeds and a SCAN_COMPLETE_NOTIFICATION is received for failed scan. * During processing of SCAN_COMPLETE_NOTIFICATION we clear STATUS_SCANNING and queue the "scan_completed" work. ** At this time, since the problem that caused the internal scan in first place is still present, a new internal scan is triggered. The behavior at this point is a bit different between 2.6.34 and 2.6.35 since 2.6.35 has a lot of this synchronized. The rest of the race description will thus be generalized. ** As part of preparing for the scan "is_internal_short_scan" is set to true. * At this point the completion work for fist scan is run. As part of this there is some locking missing around the "is_internal_short_scan" variable and it is set to "false". ** Now the second scan runs and it considers itself a real (not internal0 scan and thus causes problems with wrong memory being accessed. The fix is twofold. * Since "is_internal_short_scan" should be protected by mutex, fix this in scan completion work so that changes to it can be serialized. * Do not queue a new internal scan if one is in progress. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=15824 Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-05-20can: SJA1000 add missing spin_lock_init()Oliver Hartkopp
As remarked by Sam Ravnborg the spin_lock variable, that has been introduced in commit 57c8a456640fa3ca777652f11f2db4179a3e66b6 ("can: Fix SJA1000 command register writes on SMP systems") has not been initialized properly. This patch adds the initialization to allow spinlock debugging. Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> CC: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-20sh_eth: Fix memleak in sh_mdio_releaseDenis Kirjanov
Allocated memory for IRQs should be freed when releasing the mii_bus Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-20ixgbe:add support for a new 82599 10G Base-T deviceMallikarjuna R Chilakala
This adds support for a new copper device for 82599, device id 0x151c. This 82599 10GBase-T device uses the PHY's internal temperature sensor to guard against over-temp conditions. In this scenario the PHY will be put in a low power mode and link will no longer be able to transmit or receive any data. When this occurs, the over-temp interrupt is latched and driver logs this error message. A HW reset or power cycle is required to clear this status. Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-20Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (229 commits) USB: remove unused usb_buffer_alloc and usb_buffer_free macros usb: musb: update gfp/slab.h includes USB: ftdi_sio: fix legacy SIO-device header USB: kl5usb105: reimplement using generic framework USB: kl5usb105: minor clean ups USB: kl5usb105: fix memory leak USB: io_ti: use kfifo to implement write buffering USB: io_ti: remove unsused private counter USB: ti_usb: use kfifo to implement write buffering USB: ir-usb: fix incorrect write-buffer length USB: aircable: fix incorrect write-buffer length USB: safe_serial: straighten out read processing USB: safe_serial: reimplement read using generic framework USB: safe_serial: reimplement write using generic framework usb-storage: always print quirks USB: usb-storage: trivial debug improvements USB: oti6858: use port write fifo USB: oti6858: use kfifo to implement write buffering USB: cypress_m8: use kfifo to implement write buffering USB: cypress_m8: remove unused drain define ... Fix up conflicts (due to usb_buffer_alloc/free renaming) in drivers/input/tablet/acecad.c drivers/input/tablet/kbtab.c drivers/input/tablet/wacom_sys.c drivers/media/video/gspca/gspca.c sound/usb/usbaudio.c
2010-05-20Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits) qlcnic: adding co maintainer ixgbe: add support for active DA cables ixgbe: dcb, do not tag tc_prio_control frames ixgbe: fix ixgbe_tx_is_paused logic ixgbe: always enable vlan strip/insert when DCB is enabled ixgbe: remove some redundant code in setting FCoE FIP filter ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp ixgbe: fix header len when unsplit packet overflows to data buffer ipv6: Never schedule DAD timer on dead address ipv6: Use POSTDAD state ipv6: Use state_lock to protect ifa state ipv6: Replace inet6_ifaddr->dead with state cxgb4: notify upper drivers if the device is already up when they load cxgb4: keep interrupts available when the ports are brought down cxgb4: fix initial addition of MAC address cnic: Return SPQ credit to bnx2x after ring setup and shutdown. cnic: Convert cnic_local_flags to atomic ops. can: Fix SJA1000 command register writes on SMP systems bridge: fix build for CONFIG_SYSFS disabled ARCNET: Limit com20020 PCI ID matches for SOHARD cards ... Fix up various conflicts with pcmcia tree drivers/net/ {pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and wireless/orinoco/spectrum_cs.c} and feature removal (Documentation/feature-removal-schedule.txt). Also fix a non-content conflict due to pm_qos_requirement getting renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
2010-05-20USB: remove leftover references to udev->autosuspend_disabledAlan Stern
This patch (as1373) fixes a couple of drivers outside the USB subtree. Devices are now disabled or enabled for autosuspend by calling a core function instead of setting a flag. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-20USB: rename usb_buffer_alloc() and usb_buffer_free() usersDaniel Mack
For more clearance what the functions actually do, usb_buffer_alloc() is renamed to usb_alloc_coherent() usb_buffer_free() is renamed to usb_free_coherent() They should only be used in code which really needs DMA coherency. All call sites have been changed accordingly, except for staging drivers. Signed-off-by: Daniel Mack <daniel@caiaq.de> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Pedro Ribeiro <pedrib@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-20Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits) vlynq: make whole Kconfig-menu dependant on architecture add descriptive comment for TIF_MEMDIE task flag declaration. EEPROM: max6875: Header file cleanup EEPROM: 93cx6: Header file cleanup EEPROM: Header file cleanup agp: use NULL instead of 0 when pointer is needed rtc-v3020: make bitfield unsigned PCI: make bitfield unsigned jbd2: use NULL instead of 0 when pointer is needed cciss: fix shadows sparse warning doc: inode uses a mutex instead of a semaphore. uml: i386: Avoid redefinition of NR_syscalls fix "seperate" typos in comments cocbalt_lcdfb: correct sections doc: Change urls for sparse Powerpc: wii: Fix typo in comment i2o: cleanup some exit paths Documentation/: it's -> its where appropriate UML: Fix compiler warning due to missing task_struct declaration UML: add kernel.h include to signal.c ...
2010-05-20Merge git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (29 commits) pcmcia: disable PCMCIA ioctl also for ARM drivers/staging/comedi: dev_node removal (quatech_daqp_cs) drivers/staging/comedi: dev_node removal (ni_mio_cs) drivers/staging/comedi: dev_node removal (ni_labpc_cs) drivers/staging/comedi: dev_node removal (ni_daq_dio24) drivers/staging/comedi: dev_node removal (ni_daq_700) drivers/staging/comedi: dev_node removal (das08_cs) drivers/staging/comedi: dev_node removal (cb_das16_cs) pata_pcmcia: get rid of extra indirection pcmcia: remove suspend-related comment from yenta_socket.c pcmcia: call pcmcia_{read,write}_cis_mem with ops_mutex held pcmcia: remove pcmcia_add_device_lock pcmcia: update gfp/slab.h includes pcmcia: remove unused mem_op.h pcmcia: do not autoadd root PCI bus resources pcmcia: clarify alloc_io_space, move it to resource handlers pcmcia: move all pcmcia_resource_ops providers into one module pcmcia: move high level CIS access code to separate file pcmcia: dev_node removal (core) pcmcia: dev_node removal (remaining drivers) ...
2010-05-20Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: PM: PM QOS update fix Freezer / cgroup freezer: Update stale locking comments PM / platform_bus: Allow runtime PM by default i2c: Fix bus-level power management callbacks PM QOS update PM / Hibernate: Fix block_io.c printk warning PM / Hibernate: Group swap ops PM / Hibernate: Move the first_sector out of swsusp_write PM / Hibernate: Separate block_io PM / Hibernate: Snapshot cleanup FS / libfs: Implement simple_write_to_buffer PM / Hibernate: document open(/dev/snapshot) side effects PM / Runtime: Add sysfs debug files PM: Improve device power management document PM: Update device power management document PM: Allow runtime_suspend methods to call pm_schedule_suspend() PM: pm_wakeup - switch to using bool
2010-05-18Merge branch 'master' of /home/davem/src/GIT/linux-2.6/David S. Miller
Conflicts: include/linux/mod_devicetable.h scripts/mod/file2alias.c
2010-05-18ixgbe: add support for active DA cablesDon Skidmore
This patch adds support of active DA cables. This is renaming and adding some PHY type enumerations. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18ixgbe: dcb, do not tag tc_prio_control framesJohn Fastabend
The network stack indicate packets should not be DCB tagged by setting the priority to TC_PRIO_CONTROL. One usage for this is lldp frames which are not suppossed to be tagged. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18ixgbe: fix ixgbe_tx_is_paused logicJohn Fastabend
The TFCS bits show the current XON state. Meaning that the device is paused if these bits are 0. This fixes the logic to work as it was intended. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18ixgbe: always enable vlan strip/insert when DCB is enabledYi Zou
when DCB mode is on, we want the HW VLAN stripping to be always enabled. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18ixgbe: remove some redundant code in setting FCoE FIP filterYi Zou
The ETQS setup for FIP out side the if..else is enough for the ETQS setup for FIP, so remove redundant code. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddpYi Zou
Make sure we point to the right offset of the fc_frame_header when VLAN header exists and HW has VLAN stripping disabled. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18ixgbe: fix header len when unsplit packet overflows to data bufferShannon Nelson
When in packet split mode, packet type is not recognized, and the packet is larger than the header size, the 82599 overflows the packet into the data area, but doesn't set the HDR_LEN field. We can safely assume the length is the current header size. This fixes an obscure corner case that can be triggered by non-ip packet headers or (more likely) by disabling the L2 packet recognition. Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18cxgb4: notify upper drivers if the device is already up when they loadDimitris Michailidis
Upper layer drivers aren't notified that a device is ready if their modules load after the device becomes ready. Add the missing notification. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18cxgb4: keep interrupts available when the ports are brought downDimitris Michailidis
The PF driver needs to remain alert while its ports are down to service requests or errors from virtual functions or FW so keep interrupts and queues available when the ports are brought down. The change makes open_device_map unnecessary so remove it. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18cxgb4: fix initial addition of MAC addressDimitris Michailidis
The call to add the MAC address during link initialization wasn't adding the address to one of the HW tables. Fix. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18cnic: Return SPQ credit to bnx2x after ring setup and shutdown.Michael Chan
Everytime the iSCSI ring finishes setup or shutdown, we need to return the SPQ (slow path queue) credit to the bnx2x driver. Without this step, the SPQ will eventually be full causing iSCSI to fail. This can happen after 3 or 4 MTU changes for example. Add code to wait for these slow path commands to complete in the RX ring and return the SPQ credit to bnx2x. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18cnic: Convert cnic_local_flags to atomic ops.Michael Chan
It is easier to expand the flags for other purposes because it does not require a spin_lock. The next bug fix patch needs a flag in cnic_local_flags. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18can: Fix SJA1000 command register writes on SMP systemsOliver Hartkopp
The SJA1000 command register is concurrently written in the rx-path to free the receive buffer _and_ in the tx-path to start the transmission. The SJA1000 data sheet, 6.4.4 COMMAND REGISTER (CMR) states: "Between two commands at least one internal clock cycle is needed in order to proceed. The internal clock is half of the external oscillator frequency." On SMP systems the current implementation leads to a write stall in the tx-path, which can be solved by adding some general locking and some time to settle the write_reg() operation for the command register. Thanks to Klaus Hitschler for the original fix and detailed problem description. This patch applies on net-2.6 and (with some offsets) on net-next-2.6 . Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17ARCNET: Limit com20020 PCI ID matches for SOHARD cardsAndreas Bombe
The SH SOHARD ARCNET cards are implemented using generic PLX Technology PCI<->IOBus bridges. Subvendor and subdevice IDs were not specified, causing the driver to attach to any such bridge and likely crash the system by attempting to initialize an unrelated device. Fix by specifying subvendor and subdevice according to the values found in the PCI-ID Repository at http://pci-ids.ucw.cz/ . Cc: stable@kernel.org Signed-off-by: Andreas Bombe <aeb@debian.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17cleanup: remove pppoe_ioctl() declaration.Rami Rosen
Hi, - This patch removes pppoe_ioctl() declaration in drivers/net/pppoe.c as it is unneeded. Regards, Rami Rosen Signed-off-by: Rami Rosen <ramirose@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17drivers/net: Use kcalloc or kzallocJulia Lawall
Use kcalloc or kzalloc rather than the combination of kmalloc and memset. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,y,flags; statement S; type T; @@ x = - kmalloc + kcalloc ( - y * sizeof(T), + y, sizeof(T), flags); if (x == NULL) S -memset(x, 0, y * sizeof(T)); @@ expression x,size,flags; statement S; @@ -x = kmalloc(size,flags); +x = kzalloc(size,flags); if (x == NULL) S -memset(x, 0, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17drivers/net/vmxnet3: Use kzallocJulia Lawall
Use kzalloc rather than the combination of kmalloc and memset. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,size,flags; statement S; @@ -x = kmalloc(size,flags); +x = kzalloc(size,flags); if (x == NULL) S -memset(x, 0, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Bhavesh Davda <bhavesh@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17drivers/net: Use kzallocJulia Lawall
Use kzalloc rather than the combination of kmalloc and memset. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,size,flags; statement S; @@ -x = kmalloc(size,flags); +x = kzalloc(size,flags); if (x == NULL) S -memset(x, 0, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17net: Add ndo_{set|get}_vf_port support for enic dynamic vnicsScott Feldman
Add enic ndo_{set|get}_vf_port ops to support setting/getting port-profile for enic dynamic devices. Enic dynamic devices are just like normal enic eth devices except dynamic enics require an extra configuration step to assign a port-profile identifier to the interface before the interface is useable. Once a port-profile is assigned, link comes up on the interface and is ready for I/O. The port-profile is used to configure the network port assigned to the interface. The network port configuration includes VLAN membership, QoS policies, and port security settings typical of a data center network. A dynamic enic initially has a zero-mac address. Before a port-profile is assigned, a valid non-zero unicast mac address should be assign to the dynamic enic interface. Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
2010-05-17drivers/net: remove useless semicolonsJoe Perches
switch and while statements don't need semicolons at end of statement [ Fixup minor conflicts with recent wimax merge... -DaveM ] Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17pegasus: fix USB device ID for ETX-US2Tadashi Abe
USB device ID definition for I-O Data ETX-US2 is wrong. Correct ID is 0x093a. Here's snippet from /proc/bus/usb/devices; T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=04bb ProdID=093a Rev= 1.01 S: Manufacturer=I-O DATA DEVICE,INC. S: Product=I-O DATA ETX2-US2 S: SerialNumber=A26427 C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=224mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=00 Driver=pegasus E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=125us This patch enables pegasus driver to work fine with ETX-US2. Signed-off-by: Tadashi Abe <tabe@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17can: sja1000 platform data fixesWolfgang Grandegger
The member "clock" of struct "sja1000_platform_data" is documented as "CAN bus oscillator frequency in Hz" but it's actually used as the CAN clock frequency, which is half of it. To avoid further confusion, this patch fixes it by renaming the member to "osc_freq". That way, also non mainline users will notice the change. The platform code for the relevant boards is updated accordingly. Furthermore, pre-defined values are now used for the members "ocr" and "cdr". Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2010-05-17dm9000: fix "BUG: spinlock recursion"Baruch Siach
dm9000_set_rx_csum and dm9000_hash_table are called from atomic context (in dm9000_init_dm9000), and from non-atomic context (via ethtool_ops and net_device_ops respectively). This causes a spinlock recursion BUG. Fix this by renaming these functions to *_unlocked for the atomic context, and make the original functions locking wrappers for use in the non-atomic context. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17drivers/net/usb: Use kmemdupJulia Lawall
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17drivers/net/usb: Use kmemdupJulia Lawall
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17drivers/net/usb: Use kmemdupJulia Lawall
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17fsl_pq_mdio: Fix mdiobus allocation handlingAnton Vorontsov
The driver could return success code even if mdiobus_alloc() failed. This patch fixes the issue. Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17r6040: fix link checking with switchesFlorian Fainelli
The current link checking logic only works for one port, which is not correct for swiches were multiple ports can have different link status. As a result we would only check for link status on port 1 of the switch. Move the calls to mii_check_media in r6040_timer which will be polling a single PHY chip correctly and assume link is up for switches. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17gianfar: Remove legacy PM callbacksAnton Vorontsov
These callbacks were needed because dev_pm_ops support for OF platform devices was in the powerpc tree, and the patch that added dev_pm_ops for gianfar driver was in the netdev tree. Now that netdev and powerpc trees have merged into Linus' tree, we can remove the legacy hooks. Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17bnx2x: avoid TX timeout when stopping deviceStanislaw Gruszka
When stop device call netif_carrier_off() just after disabling TX queue to avoid possibility of netdev watchdog warning and ->ndo_tx_timeout() invocation. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17bnx2: Use netif_carrier_off() to prevent timeout.Michael Chan
Based on original patch from Stanislaw Gruszka <sgruszka@redhat.com>. Using netif_carrier_off() is better than updating all the ->trans_start on all the tx queues. netif_carrier_off() needs to be called after bnx2_disable_int_sync() to guarantee no race conditions with the serdes timers that can modify the carrier state. If the chip or phy is reset, carrier will turn back on when we get the link interrupt. If there is no reset, we need to turn carrier back on in bnx2_netif_start(). Again, the phy_lock prevents race conditions with the serdes timers. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17bnx2: Update 5709 MIPS firmware and version to 2.0.15.Michael Chan
New firmware fixes a performance regression on small packets. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-28 03:14:18 +0000