| Age | Commit message (Collapse) | Author |
|---|
|
Update the features after calling register_netdev() otherwise the
device features are not set up correctly and it not possible to change
the MTU of the device. After this change, the features reported by
ethtool match the device's features before the commit which introduced
the issue and it is possible to change the device's MTU.
Fixes: f599c64fdf7d ("xen-netfront: Fix race between device setup and open")
Reported-by: Liam Shepherd <liam@dancer.es>
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: f599c64fdf7d ("xen-netfront: Fix race between device setup and open")
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The max number of slots used in xennet_get_responses() is set to
MAX_SKB_FRAGS + (rx->status <= RX_COPY_THRESHOLD).
In old kernel-xen MAX_SKB_FRAGS was 18, while nowadays it is 17. This
difference is resulting in frequent messages "too many slots" and a
reduced network throughput for some workloads (factor 10 below that of
a kernel-xen based guest).
Replacing MAX_SKB_FRAGS by XEN_NETIF_NR_SLOTS_MIN for calculation of
the max number of slots to use solves that problem (tests showed no
more messages "too many slots" and throughput was as high as with the
kernel-xen based guest system).
Replace MAX_SKB_FRAGS-2 by XEN_NETIF_NR_SLOTS_MIN-1 in
netfront_tx_slot_available() for making it clearer what is really being
tested without actually modifying the tested value.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A toolstack may delete the vif frontend and backend xenstore entries
while xen-netfront is in the removal code path. In that case, the
checks for xenbus_read_driver_state would return XenbusStateUnknown, and
xennet_remove would hang indefinitely. This hang prevents system
shutdown.
xennet_remove must be able to handle XenbusStateUnknown, and
netback_changed must also wake up the wake_queue for that state as well.
Fixes: 5b5971df3bc2 ("xen-netfront: remove warning when unloading module")
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Cc: Eduardo Otubo <otubo@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
When a netfront device is set up it registers a netdev fairly early on,
before it has set up the queues and is actually usable. A userspace tool
like NetworkManager will immediately try to open it and access its state
as soon as it appears. The bug can be reproduced by hotplugging VIFs
until the VM runs out of grant refs. It registers the netdev but fails
to set up any queues (since there are no more grant refs). In the
meantime, NetworkManager opens the device and the kernel crashes trying
to access the queues (of which there are none).
Fix this in two ways:
* For initial setup, register the netdev much later, after the queues
are setup. This avoids the race entirely.
* During a suspend/resume cycle, the frontend reconnects to the backend
and the queues are recreated. It is possible (though highly unlikely) to
race with something opening the device and accessing the queues after
they have been destroyed but before they have been recreated. Extend the
region covered by the rtnl semaphore to protect against this race. There
is a possibility that we fail to recreate the queues so check for this
in the open function.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
When loading the module after unloading it, the network interface would
not be enabled and thus wouldn't have a backend counterpart and unable
to be used by the guest.
The guest would face errors like:
[root@guest ~]# ethtool -i eth0
Cannot get driver information: No such device
[root@guest ~]# ifconfig eth0
eth0: error fetching interface information: Device not found
This patch initializes the state of the netfront device whenever it is
loaded manually, this state would communicate the netback to create its
device and establish the connection between them.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
missed one spot. From Zhu Yanjun.
2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.
3) Fix checksum offloading in thunderx driver, from Sunil Goutham.
4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.
5) Fix use after free of packet headers in TIPC, from Jon Maloy.
6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.
7) Tunneling fixes in mlxsw driver, from Petr Machata.
8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
Maloney.
9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
Dumazet.
10) Fix regression in sch_sfq.c due to one of the timer_setup()
conversions. From Paolo Abeni.
11) SCTP does list_for_each_entry() using wrong struct member, fix from
Xin Long.
12) Don't use big endian netlink attribute read for
IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
Long.
13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
adding filters there. From Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
ethernet: dwmac-stm32: Fix copyright
net: via: via-rhine: use %p to format void * address instead of %x
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
myri10ge: Update MAINTAINERS
net: sched: cbq: create block for q->link.block
atm: suni: remove extraneous space to fix indentation
atm: lanai: use %p to format kernel addresses instead of %x
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
atm: fore200e: use %pK to format kernel addresses instead of %x
ambassador: fix incorrect indentation of assignment statement
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
sctp: use right member as the param of list_for_each_entry
sch_sfq: fix null pointer dereference at timer expiration
cls_bpf: don't decrement net's refcount when offload fails
net/packet: fix a race in packet_bind() and packet_notifier()
packet: fix crash in fanout_demux_rollover()
sctp: remove extern from stream sched
sctp: force the params with right types for sctp csum apis
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
...
|
|
v2:
* Replace busy wait with wait_event()/wake_up_all()
* Cannot garantee that at the time xennet_remove is called, the
xen_netback state will not be XenbusStateClosed, so added a
condition for that
* There's a small chance for the xen_netback state is
XenbusStateUnknown by the time the xen_netfront switches to Closed,
so added a condition for that.
When unloading module xen_netfront from guest, dmesg would output
warning messages like below:
[ 105.236836] xen:grant_table: WARNING: g.e. 0x903 still in use!
[ 105.236839] deferring g.e. 0x903 (pfn 0x35805)
This problem relies on netfront and netback being out of sync. By the time
netfront revokes the g.e.'s netback didn't have enough time to free all of
them, hence displaying the warnings on dmesg.
The trick here is to make netfront to wait until netback frees all the g.e.'s
and only then continue to cleanup for the module removal, and this is done by
manipulating both device states.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This converts all remaining cases of the old setup_timer() API into using
timer_setup(), where the callback argument is the structure already
holding the struct timer_list. These should have no behavioral changes,
since they just change which pointer is passed into the callback with
the same available pointers after conversion. It handles the following
examples, in addition to some other variations.
Casting from unsigned long:
void my_callback(unsigned long data)
{
struct something *ptr = (struct something *)data;
...
}
...
setup_timer(&ptr->my_timer, my_callback, ptr);
and forced object casts:
void my_callback(struct something *ptr)
{
...
}
...
setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr);
become:
void my_callback(struct timer_list *t)
{
struct something *ptr = from_timer(ptr, t, my_timer);
...
}
...
timer_setup(&ptr->my_timer, my_callback, 0);
Direct function assignments:
void my_callback(unsigned long data)
{
struct something *ptr = (struct something *)data;
...
}
...
ptr->my_timer.function = my_callback;
have a temporary cast added, along with converting the args:
void my_callback(struct timer_list *t)
{
struct something *ptr = from_timer(ptr, t, my_timer);
...
}
...
ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback;
And finally, callbacks without a data assignment:
void my_callback(unsigned long data)
{
...
}
...
setup_timer(&ptr->my_timer, my_callback, 0);
have their argument renamed to verify they're unused during conversion:
void my_callback(struct timer_list *unused)
{
...
}
...
timer_setup(&ptr->my_timer, my_callback, 0);
The conversion is done with the following Coccinelle script:
spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/timer_setup.cocci
@fix_address_of@
expression e;
@@
setup_timer(
-&(e)
+&e
, ...)
// Update any raw setup_timer() usages that have a NULL callback, but
// would otherwise match change_timer_function_usage, since the latter
// will update all function assignments done in the face of a NULL
// function initialization in setup_timer().
@change_timer_function_usage_NULL@
expression _E;
identifier _timer;
type _cast_data;
@@
(
-setup_timer(&_E->_timer, NULL, _E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E->_timer, NULL, (_cast_data)_E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, &_E);
+timer_setup(&_E._timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, (_cast_data)&_E);
+timer_setup(&_E._timer, NULL, 0);
)
@change_timer_function_usage@
expression _E;
identifier _timer;
struct timer_list _stl;
identifier _callback;
type _cast_func, _cast_data;
@@
(
-setup_timer(&_E->_timer, _callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
_E->_timer@_stl.function = _callback;
|
_E->_timer@_stl.function = &_callback;
|
_E->_timer@_stl.function = (_cast_func)_callback;
|
_E->_timer@_stl.function = (_cast_func)&_callback;
|
_E._timer@_stl.function = _callback;
|
_E._timer@_stl.function = &_callback;
|
_E._timer@_stl.function = (_cast_func)_callback;
|
_E._timer@_stl.function = (_cast_func)&_callback;
)
// callback(unsigned long arg)
@change_callback_handle_cast
depends on change_timer_function_usage@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
identifier _handle;
@@
void _callback(
-_origtype _origarg
+struct timer_list *t
)
{
(
... when != _origarg
_handletype *_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
... when != _origarg
|
... when != _origarg
_handletype *_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
... when != _origarg
|
... when != _origarg
_handletype *_handle;
... when != _handle
_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
... when != _origarg
|
... when != _origarg
_handletype *_handle;
... when != _handle
_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
... when != _origarg
)
}
// callback(unsigned long arg) without existing variable
@change_callback_handle_cast_no_arg
depends on change_timer_function_usage &&
!change_callback_handle_cast@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
@@
void _callback(
-_origtype _origarg
+struct timer_list *t
)
{
+ _handletype *_origarg = from_timer(_origarg, t, _timer);
+
... when != _origarg
- (_handletype *)_origarg
+ _origarg
... when != _origarg
}
// Avoid already converted callbacks.
@match_callback_converted
depends on change_timer_function_usage &&
!change_callback_handle_cast &&
!change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier t;
@@
void _callback(struct timer_list *t)
{ ... }
// callback(struct something *handle)
@change_callback_handle_arg
depends on change_timer_function_usage &&
!match_callback_converted &&
!change_callback_handle_cast &&
!change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
@@
void _callback(
-_handletype *_handle
+struct timer_list *t
)
{
+ _handletype *_handle = from_timer(_handle, t, _timer);
...
}
// If change_callback_handle_arg ran on an empty function, remove
// the added handler.
@unchange_callback_handle_arg
depends on change_timer_function_usage &&
change_callback_handle_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
identifier t;
@@
void _callback(struct timer_list *t)
{
- _handletype *_handle = from_timer(_handle, t, _timer);
}
// We only want to refactor the setup_timer() data argument if we've found
// the matching callback. This undoes changes in change_timer_function_usage.
@unchange_timer_function_usage
depends on change_timer_function_usage &&
!change_callback_handle_cast &&
!change_callback_handle_cast_no_arg &&
!change_callback_handle_arg@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type change_timer_function_usage._cast_data;
@@
(
-timer_setup(&_E->_timer, _callback, 0);
+setup_timer(&_E->_timer, _callback, (_cast_data)_E);
|
-timer_setup(&_E._timer, _callback, 0);
+setup_timer(&_E._timer, _callback, (_cast_data)&_E);
)
// If we fixed a callback from a .function assignment, fix the
// assignment cast now.
@change_timer_function_assignment
depends on change_timer_function_usage &&
(change_callback_handle_cast ||
change_callback_handle_cast_no_arg ||
change_callback_handle_arg)@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_func;
typedef TIMER_FUNC_TYPE;
@@
(
_E->_timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E->_timer.function =
-&_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E->_timer.function =
-(_cast_func)_callback;
+(TIMER_FUNC_TYPE)_callback
;
|
_E->_timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E._timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E._timer.function =
-&_callback;
+(TIMER_FUNC_TYPE)_callback
;
|
_E._timer.function =
-(_cast_func)_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E._timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
;
)
// Sometimes timer functions are called directly. Replace matched args.
@change_timer_function_calls
depends on change_timer_function_usage &&
(change_callback_handle_cast ||
change_callback_handle_cast_no_arg ||
change_callback_handle_arg)@
expression _E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_data;
@@
_callback(
(
-(_cast_data)_E
+&_E->_timer
|
-(_cast_data)&_E
+&_E._timer
|
-_E
+&_E->_timer
)
)
// If a timer has been configured without a data argument, it can be
// converted without regard to the callback argument, since it is unused.
@match_timer_function_unused_data@
expression _E;
identifier _timer;
identifier _callback;
@@
(
-setup_timer(&_E->_timer, _callback, 0);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0L);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0UL);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0L);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0UL);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0L);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0UL);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0L);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0UL);
+timer_setup(_timer, _callback, 0);
)
@change_callback_unused_data
depends on match_timer_function_unused_data@
identifier match_timer_function_unused_data._callback;
type _origtype;
identifier _origarg;
@@
void _callback(
-_origtype _origarg
+struct timer_list *unused
)
{
... when != _origarg
}
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
RFC791 specifies the minimum MTU to be 68, while xen-net{front|back}
drivers use a minimum value of 0.
When set MTU to 0~67 with xen_net{front|back} driver, the network
will become unreachable immediately, the guest can no longer be pinged.
xen_net{front|back} should not allow the user to set this value which causes
network problems.
Reported-by: Chen Shi <cheshi@redhat.com>
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
xennet_start_xmit() might copy skb with inappropriate layout
into a fresh one.
Old skb is freed, and at this point it is not a drop, but
a consume. New skb will then be either consumed or dropped.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unavoidable crashes in netfront_resume() and netback_changed() after a
previous fail in talk_to_netback() (e.g. when we fail to read MAC from
xenstore) were discovered. The failure path in talk_to_netback() does
unregister/free for netdev but we don't reset drvdata and we try accessing
it after resume.
Fix the bug by removing the whole xen device completely with
device_unregister(), this guarantees we won't have any calls into netfront
after a failure.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
"Highlights:
1) Support TX_RING in AF_PACKET TPACKET_V3 mode, from Sowmini
Varadhan.
2) Simplify classifier state on sk_buff in order to shrink it a bit.
From Willem de Bruijn.
3) Introduce SIPHASH and it's usage for secure sequence numbers and
syncookies. From Jason A. Donenfeld.
4) Reduce CPU usage for ICMP replies we are going to limit or
suppress, from Jesper Dangaard Brouer.
5) Introduce Shared Memory Communications socket layer, from Ursula
Braun.
6) Add RACK loss detection and allow it to actually trigger fast
recovery instead of just assisting after other algorithms have
triggered it. From Yuchung Cheng.
7) Add xmit_more and BQL support to mvneta driver, from Simon Guinot.
8) skb_cow_data avoidance in esp4 and esp6, from Steffen Klassert.
9) Export MPLS packet stats via netlink, from Robert Shearman.
10) Significantly improve inet port bind conflict handling, especially
when an application is restarted and changes it's setting of
reuseport. From Josef Bacik.
11) Implement TX batching in vhost_net, from Jason Wang.
12) Extend the dummy device so that VF (virtual function) features,
such as configuration, can be more easily tested. From Phil
Sutter.
13) Avoid two atomic ops per page on x86 in bnx2x driver, from Eric
Dumazet.
14) Add new bpf MAP, implementing a longest prefix match trie. From
Daniel Mack.
15) Packet sample offloading support in mlxsw driver, from Yotam Gigi.
16) Add new aquantia driver, from David VomLehn.
17) Add bpf tracepoints, from Daniel Borkmann.
18) Add support for port mirroring to b53 and bcm_sf2 drivers, from
Florian Fainelli.
19) Remove custom busy polling in many drivers, it is done in the core
networking since 4.5 times. From Eric Dumazet.
20) Support XDP adjust_head in virtio_net, from John Fastabend.
21) Fix several major holes in neighbour entry confirmation, from
Julian Anastasov.
22) Add XDP support to bnxt_en driver, from Michael Chan.
23) VXLAN offloads for enic driver, from Govindarajulu Varadarajan.
24) Add IPVTAP driver (IP-VLAN based tap driver) from Sainath Grandhi.
25) Support GRO in IPSEC protocols, from Steffen Klassert"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1764 commits)
Revert "ath10k: Search SMBIOS for OEM board file extension"
net: socket: fix recvmmsg not returning error from sock_error
bnxt_en: use eth_hw_addr_random()
bpf: fix unlocking of jited image when module ronx not set
arch: add ARCH_HAS_SET_MEMORY config
net: napi_watchdog() can use napi_schedule_irqoff()
tcp: Revert "tcp: tcp_probe: use spin_lock_bh()"
net/hsr: use eth_hw_addr_random()
net: mvpp2: enable building on 64-bit platforms
net: mvpp2: switch to build_skb() in the RX path
net: mvpp2: simplify MVPP2_PRS_RI_* definitions
net: mvpp2: fix indentation of MVPP2_EXT_GLOBAL_CTRL_DEFAULT
net: mvpp2: remove unused register definitions
net: mvpp2: simplify mvpp2_bm_bufs_add()
net: mvpp2: drop useless fields in mvpp2_bm_pool and related code
net: mvpp2: remove unused 'tx_skb' field of 'struct mvpp2_tx_queue'
net: mvpp2: release reference to txq_cpu[] entry after unmapping
net: mvpp2: handle too large value in mvpp2_rx_time_coal_set()
net: mvpp2: handle too large value handling in mvpp2_rx_pkts_coal_set()
net: mvpp2: remove useless arguments in mvpp2_rx_{pkts, time}_coal_set
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"Xen features and fixes:
- a series from Boris Ostrovsky adding support for booting Linux as
Xen PVH guest
- a series from Juergen Gross streamlining the xenbus driver
- a series from Paul Durrant adding support for the new device model
hypercall
- several small corrections"
* tag 'for-linus-4.11-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/privcmd: add IOCTL_PRIVCMD_RESTRICT
xen/privcmd: Add IOCTL_PRIVCMD_DM_OP
xen/privcmd: return -ENOTTY for unimplemented IOCTLs
xen: optimize xenbus driver for multiple concurrent xenstore accesses
xen: modify xenstore watch event interface
xen: clean up xenbus internal headers
xenbus: Neaten xenbus_va_dev_error
xen/pvh: Use Xen's emergency_restart op for PVH guests
xen/pvh: Enable CPU hotplug
xen/pvh: PVH guests always have PV devices
xen/pvh: Initialize grant table for PVH guests
xen/pvh: Make sure we don't use ACPI_IRQ_MODEL_PIC for SCI
xen/pvh: Bootstrap PVH guest
xen/pvh: Import PVH-related Xen public interfaces
xen/x86: Remove PVH support
x86/boot/32: Convert the 32-bit pgtable setup code from assembly to C
xen/manage: correct return value check on xenbus_scanf()
x86/xen: Fix APIC id mismatch warning on Intel
xen/netback: set default upper limit of tx/rx queues to 8
xen/netfront: set default upper limit of tx/rx queues to 8
|
|
|
|
rx_refill_timer should be deleted as soon as we disconnect from the
backend since otherwise it is possible for the timer to go off before
we get to xennet_destroy_queues(). If this happens we may dereference
queue->rx.sring which is set to NULL in xennet_disconnect_backend().
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a crash when running out of grant refs when creating many
queues across many netdevs.
* If creating queues fails (i.e. there are no grant refs available),
call xenbus_dev_fatal() to ensure that the xenbus device is set to the
closed state.
* If no queues are created, don't call xennet_disconnect_backend as
netdev->real_num_tx_queues will not have been set correctly.
* If setup_netfront() fails, ensure that all the queues created are
cleaned up, not just those that have been set up.
* If any queues were set up and an error occurs, call
xennet_destroy_queues() to clean up the napi context.
* If any fatal error occurs, unregister and destroy the netdev to avoid
leaving around a half setup network device.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 90c311b0eeea ("xen-netfront: Fix Rx stall during network
stress and OOM") caused the refill timer to be triggerred almost on
all invocations of xennet_alloc_rx_buffers for certain workloads.
This reworks the fix by reverting to the old behaviour and taking into
consideration the skb allocation failure. Refill timer is now triggered
on insufficient requests or skb allocation failure.
Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com>
Fixes: 90c311b0eeea (xen-netfront: Fix Rx stall during network stress and OOM)
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396ba
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default for the number of tx/rx queues of one interface is the
number of vcpus of the system today. As each queue pair reserves 512
grant pages this default consumes a ridiculous number of grants for
large guests.
Limit the queue number to 8 as default. This value can be modified
via a module parameter if required.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
Two trivial overlapping changes conflicts in MPLS and mlx5.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During an OOM scenario, request slots could not be created as skb
allocation fails. So the netback cannot pass in packets and netfront
wrongly assumes that there is no more work to be done and it disables
polling. This causes Rx to stall.
The issue is with the retry logic which schedules the timer if the
created slots are less than NET_RX_SLOTS_MIN. The count of new request
slots to be pushed are calculated as a difference between new req_prod
and rsp_cons which could be more than the actual slots, if there are
unconsumed responses.
The fix is to calculate the count of newly created slots as the
difference between new req_prod and old req_prod.
Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"Xen features and fixes for 4.10
These are some fixes, a move of some arm related headers to share them
between arm and arm64 and a series introducing a helper to make code
more readable.
The most notable change is David stepping down as maintainer of the
Xen hypervisor interface. This results in me sending you the pull
requests for Xen related code from now on"
* tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (29 commits)
xen/balloon: Only mark a page as managed when it is released
xenbus: fix deadlock on writes to /proc/xen/xenbus
xen/scsifront: don't request a slot on the ring until request is ready
xen/x86: Increase xen_e820_map to E820_X_MAX possible entries
x86: Make E820_X_MAX unconditionally larger than E820MAX
xen/pci: Bubble up error and fix description.
xen: xenbus: set error code on failure
xen: set error code on failures
arm/xen: Use alloc_percpu rather than __alloc_percpu
arm/arm64: xen: Move shared architecture headers to include/xen/arm
xen/events: use xen_vcpu_id mapping for EVTCHNOP_status
xen/gntdev: Use VM_MIXEDMAP instead of VM_IO to avoid NUMA balancing
xen-scsifront: Add a missing call to kfree
MAINTAINERS: update XEN HYPERVISOR INTERFACE
xenfs: Use proc_create_mount_point() to create /proc/xen
xen-platform: use builtin_pci_driver
xen-netback: fix error handling output
xen: make use of xenbus_read_unsigned() in xenbus
xen: make use of xenbus_read_unsigned() in xen-pciback
xen: make use of xenbus_read_unsigned() in xen-fbfront
...
|
|
Several cases of bug fixes in 'net' overlapping other changes in
'net-next-.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use xenbus_read_unsigned() instead of xenbus_scanf() when possible.
This requires to change the type of some reads from int to unsigned,
but these cases have been wrong before: negative values are not allowed
for the modified cases.
Cc: netdev@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
|
|
IS_ERR_VALUE() in commit 87557efc27f6a50140fb20df06a917f368ce3c66
("xen-netfront: do not cast grant table reference to signed short") would
not return true for error code unless we cast ref first to type int.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While grant reference is of type uint32_t, xen-netfront erroneously casts
it to signed short in BUG_ON().
This would lead to the xen domU panic during boot-up or migration when it
is attached with lots of paravirtual devices.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hyperv_net:
- set min/max_mtu, per Haiyang, after rndis_filter_device_add
virtio_net:
- set min/max_mtu
- remove virtnet_change_mtu
vmxnet3:
- set min/max_mtu
xen-netback:
- min_mtu = 0, max_mtu = 65517
xen-netfront:
- min_mtu = 0, max_mtu = 65535
unisys/visor:
- clean up defines a little to not clash with network core or add
redundat definitions
CC: netdev@vger.kernel.org
CC: virtualization@lists.linux-foundation.org
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Shrikrishna Khare <skhare@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: Wei Liu <wei.liu2@citrix.com>
CC: Paul Durrant <paul.durrant@citrix.com>
CC: David Kershner <david.kershner@unisys.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Small packet loss is reported on complex multi host network configurations
including tunnels, NAT, ... My investigation led me to the following check
in netback which drops packets:
if (unlikely(txreq.size < ETH_HLEN)) {
netdev_err(queue->vif->dev,
"Bad packet size: %d\n", txreq.size);
xenvif_tx_err(queue, &txreq, extra_count, idx);
break;
}
But this check itself is legitimate. SKBs consist of a linear part (which
has to have the ethernet header) and (optionally) a number of frags.
Netfront transmits the head of the linear part up to the page boundary
as the first request and all the rest becomes frags so when we're
reconstructing the SKB in netback we can't distinguish between original
frags and the 'tail' of the linear part. The first SKB needs to be at
least ETH_HLEN size. So in case we have an SKB with its linear part
starting too close to the page boundary the packet is lost.
I see two ways to fix the issue:
- Change the 'wire' protocol between netfront and netback to start keeping
the original SKB structure. We'll have to add a flag indicating the fact
that the particular request is a part of the original linear part and not
a frag. We'll need to know the length of the linear part to pre-allocate
memory.
- Avoid transmitting SKBs with linear parts starting too close to the page
boundary. That seems preferable short-term and shouldn't bring
significant performance degradation as such packets are rare. That's what
this patch is trying to achieve with skb_copy().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trying to batch Tx response events results in poor performance because
this delays freeing the transmitted skbs.
Instead use the standard RING_FINAL_CHECK_FOR_RESPONSES() macro to be
notified once the next Tx response is placed on the ring.
Signed-off-by: Malcolm Crossley <malcolm.crossley@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
- Improve balloon driver memory hotplug placement.
- Use unpopulated hotplugged memory for foreign pages (if
supported/enabled).
- Support 64 KiB guest pages on arm64.
- CPU hotplug support on arm/arm64.
* tag 'for-linus-4.4-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (44 commits)
xen: fix the check of e_pfn in xen_find_pfn_range
x86/xen: add reschedule point when mapping foreign GFNs
xen/arm: don't try to re-register vcpu_info on cpu_hotplug.
xen, cpu_hotplug: call device_offline instead of cpu_down
xen/arm: Enable cpu_hotplug.c
xenbus: Support multiple grants ring with 64KB
xen/grant-table: Add an helper to iterate over a specific number of grants
xen/xenbus: Rename *RING_PAGE* to *RING_GRANT*
xen/arm: correct comment in enlighten.c
xen/gntdev: use types from linux/types.h in userspace headers
xen/gntalloc: use types from linux/types.h in userspace headers
xen/balloon: Use the correct sizeof when declaring frame_list
xen/swiotlb: Add support for 64KB page granularity
xen/swiotlb: Pass addresses rather than frame numbers to xen_arch_need_swiotlb
arm/xen: Add support for 64KB page granularity
xen/privcmd: Add support for Linux 64KB page granularity
net/xen-netback: Make it running on 64KB page granularity
net/xen-netfront: Make it running on 64KB page granularity
block/xen-blkback: Make it running on 64KB page granularity
block/xen-blkfront: Make it running on 64KB page granularity
...
|
|
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PV network protocol is using 4KB page granularity. The goal of this
patch is to allow a Linux using 64KB page granularity using network
device on a non-modified Xen.
It's only necessary to adapt the ring size and break skb data in small
chunk of 4KB. The rest of the code is relying on the grant table code.
Note that we allocate a Linux page for each rx skb but only the first
4KB is used. We may improve the memory usage by extending the size of
the rx skb.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
Sometimes xennet_create_queues() may failed to created all requested
queues, we need to update num_queues to real created to avoid NULL
pointer dereference.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If netfront connects with two (or more) queues and then reconnects with
only one queue it fails to delete or rewrite the multi-queue-num-queues
key and netback will try to use the wrong number of queues.
Always write the num-queues field if the backend has multi-queue support.
Signed-off-by: Chas Williams <3chas3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen terminology fixes from David Vrabel:
"Use the correct GFN/BFN terms more consistently"
* tag 'for-linus-4.3-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: Rename the variable xen_store_mfn to xen_store_gfn
xen/privcmd: Further s/MFN/GFN/ clean-up
hvc/xen: Further s/MFN/GFN clean-up
video/xen-fbfront: Further s/MFN/GFN clean-up
xen/tmem: Use xen_page_to_gfn rather than pfn_to_gfn
xen: Use correctly the Xen memory terminologies
arm/xen: implement correctly pfn_to_mfn
xen: Make clear that swiotlb and biomerge are dealing with DMA address
|
|
Originally that parameter was always reset to num_online_cpus during
module initialisation, which renders it useless.
The fix is to only set max_queues to num_online_cpus when user has not
provided a value.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Tested-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on include/xen/mm.h [1], Linux is mistakenly using MFN when GFN
is meant, I suspect this is because the first support for Xen was for
PV. This resulted in some misimplementation of helpers on ARM and
confused developers about the expected behavior.
For instance, with pfn_to_mfn, we expect to get an MFN based on the name.
Although, if we look at the implementation on x86, it's returning a GFN.
For clarity and avoid new confusion, replace any reference to mfn with
gfn in any helpers used by PV drivers. The x86 code will still keep some
reference of pfn_to_mfn which may be used by all kind of guests
No changes as been made in the hypercall field, even
though they may be invalid, in order to keep the same as the defintion
in xen repo.
Note that page_to_mfn has been renamed to xen_page_to_gfn to avoid a
name to close to the KVM function gfn_to_page.
Take also the opportunity to simplify simple construction such
as pfn_to_mfn(page_to_pfn(page)) into xen_page_to_gfn. More complex clean up
will come in follow-up patches.
[1] http://xenbits.xen.org/gitweb/?p=xen.git;a=commitdiff;h=e758ed14f390342513405dd766e874934573e6cb
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
If an interface isn't running napi_synchronize() will hang forever.
[ 392.248403] rmmod R running task 0 359 343 0x00000000
[ 392.257671] ffff88003760fc88 ffff880037193b40 ffff880037193160 ffff88003760fc88
[ 392.267644] ffff880037610000 ffff88003760fcd8 0000000100014c22 ffffffff81f75c40
[ 392.277524] 0000000000bc7010 ffff88003760fca8 ffffffff81796927 ffffffff81f75c40
[ 392.287323] Call Trace:
[ 392.291599] [<ffffffff81796927>] schedule+0x37/0x90
[ 392.298553] [<ffffffff8179985b>] schedule_timeout+0x14b/0x280
[ 392.306421] [<ffffffff810f91b9>] ? irq_free_descs+0x69/0x80
[ 392.314006] [<ffffffff811084d0>] ? internal_add_timer+0xb0/0xb0
[ 392.322125] [<ffffffff81109d07>] msleep+0x37/0x50
[ 392.329037] [<ffffffffa00ec79a>] xennet_disconnect_backend.isra.24+0xda/0x390 [xen_netfront]
[ 392.339658] [<ffffffffa00ecadc>] xennet_remove+0x2c/0x80 [xen_netfront]
[ 392.348516] [<ffffffff81481c69>] xenbus_dev_remove+0x59/0xc0
[ 392.356257] [<ffffffff814e7217>] __device_release_driver+0x87/0x120
[ 392.364645] [<ffffffff814e7cf8>] driver_detach+0xb8/0xc0
[ 392.371989] [<ffffffff814e6e69>] bus_remove_driver+0x59/0xe0
[ 392.379883] [<ffffffff814e84f0>] driver_unregister+0x30/0x70
[ 392.387495] [<ffffffff814814b2>] xenbus_unregister_driver+0x12/0x20
[ 392.395908] [<ffffffffa00ed89b>] netif_exit+0x10/0x775 [xen_netfront]
[ 392.404877] [<ffffffff81124e08>] SyS_delete_module+0x1d8/0x230
[ 392.412804] [<ffffffff8179a8ee>] system_call_fastpath+0x12/0x71
Signed-off-by: Chas Williams <3chas3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If you simply load and unload the module without starting the interfaces,
the queues are never created and you get a bad pointer dereference.
Signed-off-by: Chas Williams <3chas3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) mlx4 driver bug fixes (TX queue wakeups, csum complete indications)
from Ido Shamay, Eran Ben Elisha, and Or Gerlitz.
2) Missing unlock in error path of PTP support in renesas driver, from
Dan Carpenter.
3) Add Vitesse 8641 phy IDs to vitesse PHY driver, from Shaohui Xie.
4) Bnx2x driver bug fixes (linearization of encap packets, scratchpad
parity error notifications, flow-control and speed settings) from
Yuval Mintz, Manish Chopra, Shahed Shaikh, and Ariel Elior.
5) ipv6 extension header parsing in the igb chip has a HW errata,
disable it. Frm Todd Fujinaka.
6) Fix PCI link state locking issue in e1000e driver, from Yanir
Lubetkin.
7) Cure panics during MTU change in i40e, from Mitch Williams.
8) Don't leak promisc refs in DSA slave driver, from Gilad Ben-Yossef.
9) Add missing HAS_DMA dep to VIA Rhine driver, from Geery
Uytterhoeven.
10) Make sure DMA map/unmap calls are symmetric in bnx2x driver, from
Michal Schmidt.
11) Workaround for MDIO access problems in bcm7xxx devices, from FLorian
Fainelli.
12) Fix races in SCTP protocol between OTTB responses and route
removals, from Alexander Sverdlin.
13) Fix jumbo frame checksum issue with some mvneta devices, from Simon
Guinot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (58 commits)
sock_diag: don't broadcast kernel sockets
net: mvneta: disable IP checksum with jumbo frames for Armada 370
ARM: mvebu: update Ethernet compatible string for Armada XP
net: mvneta: introduce compatible string "marvell, armada-xp-neta"
api: fix compatibility of linux/in.h with netinet/in.h
net: icplus: fix typo in constant name
sis900: Trivial: Fix typos in enums
stmmac: Trivial: fix typo in constant name
sctp: Fix race between OOTB responce and route removal
net-Liquidio: Delete unnecessary checks before the function call "vfree"
vmxnet3: Bump up driver version number
amd-xgbe: Add the __GFP_NOWARN flag to Rx buffer allocation
net: phy: mdio-bcm-unimac: workaround initial read failures for integrated PHYs
net: bcmgenet: workaround initial read failures for integrated PHYs
net: phy: bcm7xxx: workaround MDIO management controller initial read
bnx2x: fix DMA API usage
net: via: VIA_RHINE and VIA_VELOCITY should depend on HAS_DMA
net/phy: tune get_phy_c45_ids to support more c45 phy
bnx2x: fix lockdep splat
net: fec: don't access RACC register when not available
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Xen features and cleanups for 4.2-rc0:
- add "make xenconfig" to assist in generating configs for Xen guests
- preparatory cleanups necessary for supporting 64 KiB pages in ARM
guests
- automatically use hvc0 as the default console in ARM guests"
* tag 'for-linus-4.2-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
block/xen-blkback: s/nr_pages/nr_segs/
block/xen-blkfront: Remove invalid comment
block/xen-blkfront: Remove unused macro MAXIMUM_OUTSTANDING_BLOCK_REQS
arm/xen: Drop duplicate define mfn_to_virt
xen/grant-table: Remove unused macro SPP
xen/xenbus: client: Fix call of virt_to_mfn in xenbus_grant_ring
xen: Include xen/page.h rather than asm/xen/page.h
kconfig: add xenconfig defconfig helper
kconfig: clarify kvmconfig is for kvm
xen/pcifront: Remove usage of struct timeval
xen/tmem: use BUILD_BUG_ON() in favor of BUG_ON()
hvc_xen: avoid uninitialized variable warning
xenbus: avoid uninitialized variable warning
xen/arm: allow console=hvc0 to be omitted for guests
arm,arm64/xen: move Xen initialization earlier
arm/xen: Correctly check if the event channel interrupt is present
|
|
The function netif_set_real_num_tx_queues() will return -EINVAL if
the second parameter < 1, so call this function with the second
parameter set to 0 is meaningless.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rx->status is an int16_t, print it using %d rather than %u in order to
have a meaningful value when the field is negative.
Also use %u rather than %x for rx->offset.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using xen/page.h will be necessary later for using common xen page
helpers.
As xen/page.h already include asm/xen/page.h, always use the later.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@change@
expression e, func, da;
@@
-init_timer (&e);
+setup_timer (&e, func, da);
-e.data = da;
-e.function = func;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
