summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/realtek/rtw88/coex.h
AgeCommit message (Collapse)Author
2020-03-26rtw88: add a debugfs entry to dump coex's infoYan-Hsuan Chuang
Add a new entry "coex_info" in debugfs to dump coex's states for us to debug on coex's issues. The basic concept for co-existence (coex, usually for WiFi + BT) is to decide a strategy based on the current status of WiFi and BT. So, it means the WiFi driver requires to gather information from BT side and choose a strategy (TDMA/table/HW settings). Althrough we can easily check the current status of WiFi, e.g., from kernel log or just dump the hardware registers, it is still very difficult for us to gather so many different types of WiFi states (such as RFE config, antenna, channel/band, TRX, Power save). Also we will need BT's information that is stored in "struct rtw_coex". So it is necessary for us to have a debugfs that can dump all of the WiFi/BT information required. Note that to debug on coex related issues, we usually need a longer period of time of coex_info dump every 2 seconds (for example, 30 secs, so we should have 15 times of coex_info's dump). Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Reviewed-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200313033008.20070-2-yhchuang@realtek.com
2019-09-13rtw88: 8822c: add SW DPK supportTzu-En Huang
Power amplifiers are not linear components, and require DPK to reduce its nonlinearity. DPK is called Digital Pre-distortion Calibration, can be used to compensate the output of power. DPK tracking is in charge of tracking the thermal changes. And it then shifts the power curve accordingly, which makes the power output remains linear even if the PA works in different temperature. To perform DPK, the parameter table should also be updated. And the table will be applied when device is powered on. Then DPK will reference the values to calibrate. Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-08-06rtw88: add BT co-existence supportYan-Hsuan Chuang
Both RTL8822BE/RTL8822CE are WiFi + BT combo chips. Since WiFi and BT use 2.4GHz to transmit, it is important to make sure they run concurrently without interfering each other. To achieve this, WiFi driver requires a mechanism to collaborate with BT, whether they share the antenna(s) or not. The final decision made by the co-existence mechanism is to choose a proper strategy, or called "tdma/table", and inform either firmware or hardware of the strategy. To choose a strategy, co-existence mechanism needs to have enough information from WiFi and BT. BT information is provided through firmware C2H. The contents describe the current status of BT, such as if BT is connected or is idle, or the profile that is being used. WiFi information can be provided by WiFi itself. The WiFi driver will call various of "notify" functions each time the state of WiFi changed, such as WiFi is going to switch channel or is connected. Also WiFi driver can know if it shares antenna with BT by reading efuse content. Antenna configuration of the module will finally get a different strategy. Upon receiving any information from WiFi or BT, the WiFi driver will run the co-existence mechanism immediately. It will set the RF antenna configuration according to the strategy through the TDMA H2C to firmware and a hardware table. Based on the tdma/table, WiFi + BT should work with each other, and having a better user experience. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>