| Age | Commit message (Collapse) | Author |
|---|
|
commit 683b6d3... "cfg80211: pass a channel definition struct"
accidentally changed "==" to "!=".
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds support for advertising GreenField, 40MHz intolerance
or LDPC coding support to cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.
Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
This patch adds support for multiple TX queues inside mwifiex
driver. Four different queues according to WMM access categories
are defined for each virtual interface. When a packet is
received from netdev for transmission, tx pending count for
particular queue is incremented and if tx pending count has
reached upper water-mark, this queue is stopped instead of
stopping all queues. Similarly when a packet is successfully
transmitted from device, tx pending count is decremented per
queue and if pending count falls below lower water-mark, queue
operations are again resumed. This ensures that not all
tranmission is blocked if traffic with particular TOS value
suddenly increases.
Also wake all queues after association/IBSS_join/uAP_BSS_start
to enable traffic on all queues.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.
Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/mwifiex/cfg80211.c
|
|
This reverts commit 34202e28fe7fc8551313f9a035a8857db83de757
We made "34202ee.." because we didn't support custom regulatory rules
at that time. But now we use our own custom regulatory rules, so it
needs to be changed back.
Also, chan->max_power calculations in cfg80211 were broken. Hence we
started using chan->max_reg_power. Now it has got fixed in
following commit.
commit 5e31fc0815a4e2c72b1b495fe7a0d8f9bfb9e4b4
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Tue Jul 24 08:35:39 2012 +0200
wireless: reg: restore previous behaviour of chan->max_power calculations
Hence we will use chan->max_power instead of chan->max_reg_power.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
mwifiex_request_scan() takes care of synchronous internal scan
performed by driver during association.
Currently the semaphore acquired for the scan is unnecessarily
released at the end of different paths. Also, failure paths
returning error code other than "-1" are not considered.
We will release it at the end of routine to fix above issues.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the interface is down, we will abort scan by calling
cfg80211_scan_done() with abort option. This fixes WARN_ON
triggered by cfg80211 in wdev_cleanup_work().
Driver's internal variables/flags are cleared once we get
response for current scan command. Meanwhile we will block
new scan request from cfg80211.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We will delay/abort scan operation based on traffic for low
priority scan.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
De-reference and deallocate scan state on failure.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Tested-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Ryan Cairns <rtc@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The next patch will introduce a flag that is set
by default in cfg80211 so drivers and mac80211
need to use |= to set features they have so that
they don't clear the already-set feature.
We could set the flag in wiphy_register() instead
of wiphy_new() to avoid this patch, but then the
drivers couldn't *unset* flags they don't want to
use even though the implementation is generic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch adds support to send correct reason code got from
firmware when association attempt fails. Also, the error message
displayed for association failure due to network incompatibility
is modified. Current message "cannot find ssid.." misleads user.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There are cases we cannot scan when request is received.
For example, during WPA group key negociation the scan request
will be blocked. We should return an error code to cfg80211
because cfg80211_scan_done will never be called.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The firmware has support for this feature, so we offload it to
firmware. In start_ap, driver passes the inactivity timeout
value to firmware via TLVs and firmware will report STA_DEAUTH
event to driver when inactivity timer is fired.
Signed-off-by: Kevin Gan <ganhy@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When cfg80211 calls to change interface type for P2P GO, send
P2P mode config commands to firmware and set bss role and bss
mode accordingly.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When cfg80211 calls to change interface type for P2P client,
send P2P mode config commands to firmware.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Due to firmware design, driver needs to add a default P2P interface
to implement find phase and action frame handshake.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When scan is triggered from cfg80211, the request contains some IEs
and we should parse all the IEs and append each IE into a seperate
IE buffer.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add a new command to implement remain_on_channel and
cancel_remain_on_channel.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add a new command to implement mgmt_frame_register.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Advertise supported management frame types to cfg80211.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Implement mgmt_tx in cfg80211 ops through data path.
Advertise probe resp offload and skip to send probe resp in AP
or GO mode.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove unnecessary blank lines and extra tab.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
Currently scan operation is delayed/aborted based on Tx traffic
consistency. This decision is taken after receiving scan
response of first scan command from FW. But when heavy traffic
is running, we can not even afford to send first scan command
and go off channel for 30msec. We will block scan request in
this case.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The name can't be modified by the driver,
make it const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
country 00 (world regulatory domain) doesn't define channels
52 - 64 and 100 - 140. Add these channels to our custom world
regulatory domain.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We will use world regulatory domain (country 00) as default
when driver is loaded. Later after a successful association
cfg80211 will change the regulatory domain to a specific country
if the AP has advertised country IE.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
AP's country ie is parsed and 11d information is updated in firmware
while associating. Previous mwifiex_send_domain_info_cmd_fw() call in
association path is not necessary now. Hence it is removed in this
patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently AP interface has higher priority over station. Hence
separate entries are created in "adapter->bss_prio_tbl" for these
interfaces and station packet is dequeued only if there is not
packet in queue for AP. It is observed that ping for station
interface doesn't work if heavy traffic is running on AP.
The problem is fixed by having same priority for both the
interfaces. This patch also removes an extra initialisation
for "priv->bss_priority".
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds support for parsing rates from cfg80211_ap_settings
of start_ap handler. This in turn adds support for 11a and 11b phy
configurations.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
'cipher' and 'seq' coming from cfg80211 add_key handler will be
parsed in mwifiex_set_encode() to handle AES_CMAC cipher suite.
Signed-off-by: Ying Luo <luoy@marvell.com>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If HT IE is present in beacon_data of start_ap cfg80211 handler,
enable 11n flag in AP. Disable 11n flag when stop_ap handler is
called.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
This patch configures data rates to firmware using bitrate mask
provided by cfg80211.
Earlier we used to only update band information in this handler
which will be used later for ibss network. Due to recent
modifications in ibss join code we don't need to do that.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In mwifiex_set_rf_channel() ibss specific flags were unnecessarily
getting modified for infra and AP mode. This patch removes
mwifiex_set_rf_channel() function and adds equivalant code in infra,
ibss and AP path.
For ibss, now we are chosing band based on channel type and basic
rates provided in ibss join request. We can start ibss network in
A only, B only, G only, BG, BGN, AN mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
1) Remove unnecessary wrapper functions.
2) Currently we don't have command to set Tx data rate, so
mwifiex_rate_ioctl_set_rate_value() function and related code
can be removed.
3) "ds_rate" filled by mwifiex_ret_tx_rate_cfg() is never used.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
1) Recently we removed set_channel cfg80211 handler. Also, cfg80211
blocks ibss connection requests if ibss network is already started
/joined. Hence the code to restart ibss network in new channel
(mwifiex_drv_change_adhoc_chan() function) becomes redundant.
2) mwifiex_bss_set_channel() function is redundant. It does some
error checking and calculate adhoc start band and adhoc channel.
Cfg80211 already takes care of error checking and provides correct
channel information to the driver. Adhoc start band is already
calculated in mwifiex_set_rf_channel() function.
Other associated code is also removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Conflicts:
drivers/net/wireless/iwmc3200wifi/cfg80211.c
drivers/net/wireless/mwifiex/cfg80211.c
|
|
mwifiex driver supports 2x2 chips as well. Hence valid mcs values
are 0 to 15. The check for mcs index is corrected in this patch.
For example: if 40MHz is enabled and mcs index is 11, "iw link"
command would show "tx bitrate: 108.0 MBit/s" without this patch.
Now it shows "tx bitrate: 108.0 MBit/s MCS 11 40Mhz" with the patch.
Cc: "3.2.y, 3.3.y, 3.4.y" <stable@vger.kernel.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This enables user to set mode of Tx/Rx path using "iw set antenna"
command. For non MIMO chips, the command will be used for selecting
specific antenna or configuring antenna diversity mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
