| Age | Commit message (Collapse) | Author |
|---|
|
brcmf_sdio_isr() is using in_interrupt() to distinguish if it is called
from a interrupt service routine or from a worker thread.
Passing such information from the calling context is preferred and
requested by Linus, so add an argument `in_isr' to brcmf_sdio_isr() and let
the callers pass the information about the calling context.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 4684997d9eea ("brcmfmac: reset PCIe bus on a firmware crash")
adds a reset function to recover firmware trap for PCIe bus. This commit
adds an implementation for SDIO bus.
Upon SDIO firmware trap, do below:
- Remove the device
- Reset hardware
- Probe the device again
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622144851.165248-1-chi-hsien.lin@cypress.com
|
|
NVIDIA Tegra SoCs do not like when OOB wake is enabled and WiFi interface
is in DOWN state during suspend. This results in a CPU hang on programming
OOB wake-up state of the GPIO controller during of system's suspend.
The solution is trivial: don't enable wake for the OOB interrupt when it
should be disabled.
This fixes hang on Tegra20 (Acer A500) and Tegra30 (Nexus 7) devices which
are using BCM4329 and BCM4330 WiFi chips respectively.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Along with F2 watermark (existing) configuration, F1 MesBusyCtrl
should be enabled & sdio device RX FIFO watermark should be
configured to avoid overflow errors.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Replace the array of functions with a pair of pointers to the
relevant functions.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Make it more obvious that this code acually enables interrupts, and
provide nice definitions for the bits in the register.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In preparation for removing the function array, remove all code that
refers to function by index and replace with pointers to the function
itself.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: replace BUG() with WARN() macro]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
func0 is not provided by the mmc stack as a function when probing.
Instead providing specific access functions to read/write it.
This prepares for a patch to remove the actual array entry itself.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: rephrased the commit message]
[arend: removed unrelated comment for which separate patch is warranted]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Rather than workaround the restrictions on func0 addressing in the
driver, set MMC_QUIRK_LENIENT_FN0
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The IO functions operate within the Chipcommon IO window. Explicitly
set this, rather than relying on the last initialisation IO access to
leave it set to the right value by chance.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Trivial tidy of register definitions.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Primarily this patch removes:
brcmf_sdiod_f0_writeb()
brcmf_sdiod_reg_write()
brcmf_sdiod_reg_read()
Since we no longer use the quirky method of deciding which function to
address via the address being accessed, take the opportunity to rename
some IO functions more in line with common kernel code. We also convert
those that map directly to sdio_{read,write}*() to macros.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This function is obfuscating how IO works on this chip. Remove it
and push its logic into brcmf_sdiod_reg_{read,write}().
Handling of -ENOMEDIUM is altered, but as that's pretty much broken anyway
we can ignore that.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This function sets the address of the IO window used for
SDIO accesses onto the backplane of the chip.
It currently uses 3 separate masks despite the full mask being
defined in the code already. Remove the separate masks and clean up.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
brcmf_sdiod_intr_unregister call that removes both func1 and
func2 interrupt handlers only called when brcmf_ops_sdio_remove
is called for func 1 (which is the 2nd call) but sdio is expecting
it to be removed at the end of each sdio_remove call.
This is causing 'rmmod bcmrfmac' on a 4356-sdio chip to complain
with:
WARNING: driver brcmfmac did not remove its interrupt handler!
The modification makes calling brcmf_sdiod_intr_unregister multiple
times harmless by clearing the variables that track if interrupt
handlers have been installed, and then calls it on every
brcmf_ops_sdio_remove call instead of just remove for func 1.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When chip attach fails, brcmf_sdiod_intr_unregister is being called
but that is too early as sdiodev->settings has not been set yet
nor has brcmf_sdiod_intr_register been called.
Change to use oob_irq_requested + newly created sd_irq_requested
to decide on what to unregister at intr_unregister time.
Steps to reproduce problem:
- modprobe brcmfmac using buggy FW
- rmmod brcmfmac
- modprobe brcmfmac again.
If done with a buggy firmware, brcm_chip_attach will fail on the
2nd modprobe triggering the call to intr_unregister and the
kernel oops when attempting to de-reference sdiodev->settings->bus.sdio
which has not yet been set.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Merge module parameters and platform data in one struct. This is the
last step to move to the new platform data per device. Now parameters
of platform data will be merged with module parameters per device.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Platform data is only available for sdio. With this patch a new
platform data structure is being used which allows for platform
data for any device and configurable per device. This patch only
switches to the new structure and adds support for SDIO devices.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With commit 7d34b0560567 ("brcmfmac: Move all module parameters to
one place") a bug was introduced causing a null pointer exception.
This patch fixes the bug by initializing the sg table till after
the settings have been initialized.
Fixes: 7d34b0560567 ("brcmfmac: Move all module parameters to one place")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Instead to having macro definition for millisecond timeout have
the definition directly in jiffies. This makes the unit of the
value immediately clear and may result in code that is bit more
compact.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The function brcmf_sdio_wd_timer() has wdtick parameter. However, it
is only called with two values and as such the parameter is replaced
with boolean value indicating the timer should be active or not.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
All bus drivers (sdio, usb and pcie) require firmware files which
needs to be downloaded to the device, The definitions and mapping
of device id and revision to firmware and nvram file is done by
each bus driver. This patch creates common functions and defines
to simplify and unify the definition of these firmware and nvram
files and mapping.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Part of reorganising wireless drivers directory and Kconfig. Note that I had to
edit Makefiles from subdirectories to use the new location.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
