Age | Commit message (Collapse) | Author |
|
Gives drivers the definitions needed to advertise support
for S1G bands.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200602062247.23212-1-thomas@adapt-ip.com
Link: https://lore.kernel.org/r/20200731055636.795173-1-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3113e8b203b9debfb72d81e0f3dcace
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a NULL pointer dereference in the probe path for AHB devices.
There attr parameter in the ath10k_ce_alloc_pipe() function is not
initialized, but accessed. This function is called by
ath10k_pci_setup_resource() which is called by ath10k_ahb_probe().
The struct ath10k_pci is also used for AHB devices and not only for PCI
devices.
The initialization of the new members of struct ath10k_pci is moved to
ath10k_pci_setup_resource() which is used by the PCI and the AHB code.
This also fixes a use after free bug in ath10k_pci_remove() when ar_pci
is accessed after ath10k_core_destroy() was called, which calls
ieee80211_free_hw() and frees this memory.
This fixes the following bug seen with backports-5.8-rc2 on OpenWrt on a
IPQ4019 device:
[ 11.117462] 8<--- cut here ---
[ 11.117494] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 11.119510] pgd = f377fd58
[ 11.127657] [00000000] *pgd=8e9a0835, *pte=00000000, *ppte=00000000
[ 11.130206] Internal error: Oops: 17 [#1] SMP ARM
[ 11.136339] Modules linked in: ath10k_pci(+) ath10k_core ath xt_state xt_nat xt_conntrack xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD pppox ppp_generic nf_nat nf_flow_table_hw nf_flow_table nf_conntrack_rtcache nf_conntrack mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_multiport xt_mark xt_mac xt_limit xt_comment xt_TCPMSS xt_LOG slhc nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 iptable_mangle iptable_filter ip_tables crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 leds_gpio xhci_plat_hcd xhci_pci xhci_hcd dwc3 dwc3_qcom gpio_button_hotplug
[ 11.174355] CPU: 2 PID: 257 Comm: kmodloader Not tainted 5.4.51 #0
[ 11.196585] Hardware name: Generic DT based system
[ 11.202746] PC is at ath10k_ce_alloc_pipe+0x58/0x180 [ath10k_core]
[ 11.207459] LR is at ath10k_pci_alloc_pipes+0x94/0xc8 [ath10k_pci]
[ 11.213600] pc : [<bf2c96cc>] lr : [<bf2fbf98>] psr: 80000013
[ 11.219760] sp : cea0dc90 ip : cf4001f0 fp : 00000001
[ 11.225923] r10: 00000000 r9 : 00000018 r8 : ce4963b4
[ 11.231133] r7 : 00000000 r6 : ce491ea0 r5 : 00000000 r4 : ce4963b4
[ 11.236342] r3 : 0004a000 r2 : 0004a000 r1 : bf2d0d70 r0 : 00000006
[ 11.242942] Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 11.249452] Control: 10c5387d Table: 8e9c006a DAC: 00000051
[ 11.256656] Process kmodloader (pid: 257, stack limit = 0xaba286ca)
[ 11.262386] Stack: (0xcea0dc90 to 0xcea0e000)
[ 11.268462] dc80: 00000000 ce49629c ce491ea0 ce4963bc
[ 11.272984] dca0: ce495ea0 bf2fbf98 00000002 ce4963a8 ce495ea0 00000000 ce491ea0 cf95d800
[ 11.281142] dcc0: cf95d810 cf95d810 00000001 bf2fc854 00000000 cf95d800 bf300748 ce495ea0
[ 11.289304] dce0: ce491ea0 d1300000 cf95d800 bf2fde8c 00000000 00000001 ce49cea0 00000000
[ 11.297462] dd00: 00000000 00000000 bf3010a0 cf95d810 bf3010a0 c0b61580 00000000 00000000
[ 11.305624] dd20: bf3010a0 0000000b c0b04e48 c06110c8 c0b61588 cf95d810 c0b61580 c060f740
[ 11.313781] dd40: cf95d810 00000000 bf3010a0 00000000 00000000 ce49d2a4 bf301100 c060fc90
[ 11.321943] dd60: 00000000 bf3010a0 cf95d810 c060fcf0 cf95d810 bf3010a0 c060fc98 c060dca4
[ 11.330101] dd80: cf809d58 cf952cb4 bf3010a0 ce967900 c0b1f2c8 c060ec28 bf3007b8 bf301038
[ 11.338263] dda0: bf3010a0 bf3010a0 c0b2d4d4 ffffe000 bf304000 c0610278 c0b04e48 c0b2d4d4
[ 11.346422] ddc0: ffffe000 bf2fe2b4 c0b04e48 bf30403c c0b04e48 c0302764 8040003f 00000001
[ 11.354582] dde0: 38e38e39 ce513580 c0b2cb50 cf801e00 cffbc6ac ce513600 cf801e00 cffbc6ac
[ 11.362740] de00: 8040003e ce49d280 00000001 c0428d54 00000001 cf801e00 cffbc6ac ce513580
[ 11.370900] de20: ce49d280 0e391998 bf301100 ce49d340 d12d2000 ce49d280 00000001 c0398c2c
[ 11.379061] de40: 00000001 cea0df34 cea0df34 00000001 d12d2000 c039ae48 bf30110c 00007fff
[ 11.387221] de60: bf301100 c0398044 cf804028 bf301148 c0397674 bf30126c c08ee5c0 c08ee70c
[ 11.395380] de80: bf30110c c0b04e48 c08ee518 00000000 c08ee570 c0b04e48 ce513600 fffff000
[ 11.403540] dea0: 00000001 ce513580 0000000d 0000000d 00000000 00000000 00000000 00000000
[ 11.411698] dec0: 00000000 00000000 6e72656b 00006c65 00000000 00000000 00000000 00000000
[ 11.419858] dee0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 11.428018] df00: 00000000 0e391998 00000000 0000c610 d12de610 00000000 0062c620 ffffe000
[ 11.436180] df20: 000129d1 00000051 00000000 c039b228 00000000 d12d7afd d12d8e80 d12d2000
[ 11.444337] df40: 0000c610 d12de0e8 d12ddfa8 d12dab74 00009000 00009570 00003a2c 00009cae
[ 11.452498] df60: 00000000 00000000 00000000 00003a1c 0000001e 0000001f 00000018 00000000
[ 11.460656] df80: 00000010 00000000 00000000 00000000 00000003 00000080 c0301204 cea0c000
[ 11.468817] dfa0: 00000080 c0301000 00000000 00000000 00620010 0000c610 000129d1 00000014
[ 11.476975] dfc0: 00000000 00000000 00000003 00000080 0000c610 00000000 b6fc1d20 00000000
[ 11.485137] dfe0: bef0ad14 bef0acf8 00011e14 b6f74c94 60000010 00620010 00000000 00000000
[ 11.493390] [<bf2c96cc>] (ath10k_ce_alloc_pipe [ath10k_core]) from [<bf2fbf98>] (ath10k_pci_alloc_pipes+0x94/0xc8 [ath10k_pci])
[ 11.501498] [<bf2fbf98>] (ath10k_pci_alloc_pipes [ath10k_pci]) from [<bf2fc854>] (ath10k_pci_setup_resource+0xb8/0xf0 [ath10k_pci])
[ 11.512773] [<bf2fc854>] (ath10k_pci_setup_resource [ath10k_pci]) from [<bf2fde8c>] (ath10k_ahb_probe+0x32c/0x670 [ath10k_pci])
[ 11.524566] [<bf2fde8c>] (ath10k_ahb_probe [ath10k_pci]) from [<c06110c8>] (platform_drv_probe+0x34/0x70)
[ 11.536016] [<c06110c8>] (platform_drv_probe) from [<c060f740>] (really_probe+0x1f0/0x358)
[ 11.545729] [<c060f740>] (really_probe) from [<c060fc90>] (device_driver_attach+0x58/0x60)
[ 11.553886] [<c060fc90>] (device_driver_attach) from [<c060fcf0>] (__driver_attach+0x58/0xcc)
[ 11.562134] [<c060fcf0>] (__driver_attach) from [<c060dca4>] (bus_for_each_dev+0x68/0x8c)
[ 11.570731] [<c060dca4>] (bus_for_each_dev) from [<c060ec28>] (bus_add_driver+0x1c8/0x1d8)
[ 11.578886] [<c060ec28>] (bus_add_driver) from [<c0610278>] (driver_register+0x74/0x108)
[ 11.587060] [<c0610278>] (driver_register) from [<bf2fe2b4>] (ath10k_ahb_init+0x18/0x38 [ath10k_pci])
[ 11.595320] [<bf2fe2b4>] (ath10k_ahb_init [ath10k_pci]) from [<bf30403c>] (init_module+0x3c/0x1000 [ath10k_pci])
[ 11.604432] [<bf30403c>] (init_module [ath10k_pci]) from [<c0302764>] (do_one_initcall+0x84/0x1d8)
[ 11.614657] [<c0302764>] (do_one_initcall) from [<c0398c2c>] (do_init_module+0x5c/0x228)
[ 11.623421] [<c0398c2c>] (do_init_module) from [<c039ae48>] (load_module+0x1fc8/0x224c)
[ 11.631663] [<c039ae48>] (load_module) from [<c039b228>] (sys_init_module+0x15c/0x17c)
[ 11.639390] [<c039b228>] (sys_init_module) from [<c0301000>] (ret_fast_syscall+0x0/0x54)
[ 11.647370] Exception stack(0xcea0dfa8 to 0xcea0dff0)
[ 11.655615] dfa0: 00000000 00000000 00620010 0000c610 000129d1 00000014
[ 11.660569] dfc0: 00000000 00000000 00000003 00000080 0000c610 00000000 b6fc1d20 00000000
[ 11.668725] dfe0: bef0ad14 bef0acf8 00011e14 b6f74c94
[ 11.676886] Code: e1c321d4 e0433002 e0232397 e5843014 (e5953000)
[ 11.681958] ---[ end trace 8f35917de2e76854 ]---
Fixes: 521fc37be3d8 ("ath10k: Avoid override CE5 configuration for QCA99X0 chipsets")
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq40xx/ map-ac2200]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200714205802.17688-1-hauke@hauke-m.de
|
|
The word 'descriptor' is misspelled throughout the tree.
Fix it up accordingly:
decriptors -> descriptors
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200715124839.252822-5-kieran.bingham+renesas@ideasonboard.com
|
|
ath.git patches for v5.9. Major changes:
ath11k
* add 6G band support
* add spectral scan support
|
|
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
ath10k_htt_tx_free_msdu_id() has a lockdep assertion that htt->tx_lock
is held. Acquire the lock in a couple of error paths when calling that
function to ensure this condition is met.
Fixes: 6421969f248fd ("ath10k: refactor tx pending management")
Fixes: e62ee5c381c59 ("ath10k: Add support for htt_data_tx_desc_64 descriptor")
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604105901.1.I5b8b0c7ee0d3e51a73248975a9da61401b8f3900@changeid
|
|
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
|
|
The ath10k/qmi.h header file contains a declaration for the function
ath10k_qmi_register_service_notifier(). This function doesn't exist.
Remove the declaration.
This patch is a no-op and was just found by code inspection.
Fixes: ba94c753ccb4 ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200528122105.1.I31937dce728b441fd72cbe23447bc4710fd56ddb@changeid
|
|
Also replace generic MANUFACTURER macros by proper SDIO IDs macros.
Checks for device IDs are slightly modified to use SDIO device IDs.
This allows removal of all custom MANUFACTURER macros from ath10k.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-9-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
gcc-10 correctly points out a bug with a zero-length array in
struct ath10k_pci:
drivers/net/wireless/ath/ath10k/ahb.c: In function 'ath10k_ahb_remove':
drivers/net/wireless/ath/ath10k/ahb.c:30:9: error: array subscript 0 is outside the bounds of an interior zero-length array 'struct ath10k_ahb[0]' [-Werror=zero-length-bounds]
30 | return &((struct ath10k_pci *)ar->drv_priv)->ahb[0];
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/ath/ath10k/ahb.c:13:
drivers/net/wireless/ath/ath10k/pci.h:185:20: note: while referencing 'ahb'
185 | struct ath10k_ahb ahb[0];
| ^~~
The last addition to the struct ignored the comments and added
new members behind the array that must remain last.
Change it to a flexible-array member and move it last again to
make it work correctly, prevent the same thing from happening
again (all compilers warn about flexible-array members in the
middle of a struct) and get it to build without warnings.
Fixes: 521fc37be3d8 ("ath10k: Avoid override CE5 configuration for QCA99X0 chipsets")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200509120707.188595-2-arnd@arndb.de
|
|
gcc-10 started warning about out-of-bounds access for zero-length
arrays:
In file included from drivers/net/wireless/ath/ath10k/core.h:18,
from drivers/net/wireless/ath/ath10k/htt_rx.c:8:
drivers/net/wireless/ath/ath10k/htt_rx.c: In function 'ath10k_htt_rx_tx_fetch_ind':
drivers/net/wireless/ath/ath10k/htt.h:1683:17: warning: array subscript 65535 is outside the bounds of an interior zero-length array 'struct htt_tx_fetch_record[0]' [-Wzero-length-bounds]
1683 | return (void *)&ind->records[le16_to_cpu(ind->num_records)];
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/htt.h:1676:29: note: while referencing 'records'
1676 | struct htt_tx_fetch_record records[0];
| ^~~~~~~
Make records[] a flexible array member to allow this, moving it behind
the other zero-length member that is not accessed in a way that gcc
warns about.
Fixes: 22e6b3bc5d96 ("ath10k: add new htt definitions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200509120707.188595-1-arnd@arndb.de
|
|
ath10k(sdio/snoc) is no longer experimental. Remove experimental tag for
SDIO/SNOC from ath10k Kconfig.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507055324.15564-1-govinds@codeaurora.org
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507041127.GA31587@embeddedor
|
|
Sparse warned:
drivers/net/wireless/ath/ath10k/wmi-tlv.c:3013:34: warning: incorrect
type in assignment (different base types)
drivers/net/wireless/ath/ath10k/wmi-tlv.c:3013:34: expected
restricted __le32 [usertype] reset_after_request
drivers/net/wireless/ath/ath10k/wmi-tlv.c:3013:34: got unsigned int
[usertype] reset
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Fixes: 0f7cb26830a6 ("ath10k: add rx bitrate report for SDIO")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588747649-18051-1-git-send-email-kvalo@codeaurora.org
|
|
Currently when the sending of any management pkt
via wmi command fails, the packet is being unmapped
freed in the error handling. But the idr entry added,
which is used to track these packet is not getting removed.
Hence, during unload, in wmi cleanup, all the entries
in IDR are removed and the corresponding buffer is
attempted to be freed. This can cause a situation where
one packet is attempted to be freed twice.
Fix this error by rmeoving the msdu from the idr
list when the sending of a management packet over
wmi fails.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Fixes: 1807da49733e ("ath10k: wmi: add management tx by reference support over wmi")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588667015-25490-1-git-send-email-pillair@codeaurora.org
|
|
The qmi infrastructure sends the client a del_server
event when the client releases its qmi handle. This
is not the msg indicating the actual qmi server exiting.
In such cases the del_server msg should not be processed,
since the wifi firmware does not reset its qmi state.
Hence skip the processing of del_server event when the
driver is unloading.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Fixes: ba94c753ccb4 ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588663061-12138-1-git-send-email-pillair@codeaurora.org
|
|
Add the support to attach and map iommu
domain for targets which do not have the
support of TrustZone.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586971906-20985-4-git-send-email-pillair@codeaurora.org
|
|
Move the msa resources setup out of qmi init and
setup the msa resources as a part of probe before
the qmi init is done.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586971906-20985-3-git-send-email-pillair@codeaurora.org
|
|
The struct cfg80211_wowlan of NET_DETECT WoWLAN feature share the same
struct cfg80211_sched_scan_request together with scheduled scan request
feature, and max_sched_scan_reqs of wiphy is only used for sched scan,
and ath10k does not support scheduled scan request feature, so ath10k
does not set flag NL80211_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR, but ath10k
set max_sched_scan_reqs of wiphy to a non zero value 1, then function
nl80211_add_commands_unsplit of cfg80211 will set it support command
NL80211_CMD_START_SCHED_SCAN because max_sched_scan_reqs is a non zero
value, but actually ath10k not support it, then it leads a mismatch result
for sched scan of cfg80211, then application shill found the mismatch and
stop running case of MAC random address scan and then the case fail.
After remove max_sched_scan_reqs value, it keeps match for sched scan and
case of MAC random address scan pass.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Tested with QCA6174 PCIe with firmware WLAN.RM.4.4.1-00110-QCARMSWP-1.
Fixes: ce834e280f2f875 ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20191114050001.4658-1-wgong@codeaurora.org
|
|
As the exisiting CE configurations are defined in global, there
are the chances of QCA99X0 family chipsets CE configurations
are getting changed by the ath10k_pci_override_ce_config()
function.
The override will be hit and CE5 configurations will be changed,
when the user bring up the QCA99X0 chipsets along with QCA6174
or QCA9377 chipset. (Bring up QCA99X0 family chipsets after
QCA6174 or QCA9377).
Hence, fixing this issue by moving the global CE configuration
to radio specific CE configuration.
Tested hardware: QCA9888 & QCA6174
Tested firmware: 10.4-3.10-00047 & WLAN.RM.4.4.1.c3-00058
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587649759-14381-1-git-send-email-mkenna@codeaurora.org
|
|
'cmd' is malloced in ath10k_bmi_lz_data_large() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: d58f466a5dee ("ath10k: add large size for BMI download data for SDIO")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427104348.13570-1-weiyongjun1@huawei.com
|
|
For legacy mode, tx bitrate not show correct sometimes, for example:
iw wlan0 link
Connected to 8c:21:0a:b3:5a:64 (on wlan0)
SSID: tplinkgw
freq: 2462
RX: 19672 bytes (184 packets)
TX: 9851 bytes (87 packets)
signal: -51 dBm
rx bitrate: 54.0 MBit/s
tx bitrate: 2.8 MBit/s
This patch use the tx bitrate info from WMI_TLV_PEER_STATS_INFO_EVENTID
report from firmware, and tx bitrate show correct.
iw wlan0 link
Connected to 8c:21:0a:b3:5a:64 (on wlan0)
SSID: tplinkgw
freq: 2462
RX: 13973 bytes (120 packets)
TX: 6737 bytes (57 packets)
signal: -52 dBm
rx bitrate: 54.0 MBit/s
tx bitrate: 54.0 MBit/s
This patch only effect SDIO chip, ath10k_mac_sta_get_peer_stats_info
has check for bitrate_statistics of hw_params, it is enabled only for
"qca6174 hw3.2 sdio".
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-5-wgong@codeaurora.org
|
|
The rate code and rate kbps report by WMI_TLV_PEER_STATS_INFO_EVENTID
from firmware contains all the bitrate info which include OFDM, CCK,
HT/VHT, and mac80211 need the struct rate_info which include below
parameters:
flags: bitflag of flags from &enum rate_info_flags
mcs: mcs index if struct describes an HT/VHT/HE rate
legacy: bitrate in 100kbit/s for 802.11abg
nss: number of streams (VHT & HE only)
bw: bandwidth (from &enum rate_info_bw)
For OFDM/CCK, its rate kbps indicate the bitrate, for HT/VHT, mac80211
need the above 5 parameters to cacluate the bitrate and show by iw.
After parse the bitrate info, iw show the correct rx bitrate:
localhost ~ # iw wlan0 link
rx bitrate: 234.0 MBit/s VHT-MCS 3 80MHz VHT-NSS 2
rx bitrate: 40.5 MBit/s MCS 2 40MHz
rx bitrate: 72.2 MBit/s MCS 7 short GI
rx bitrate: 54.0 MBit/s
rx bitrate: 48.0 MBit/s
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-4-wgong@codeaurora.org
|
|
For SDIO chip, its rx indication is struct htt_rx_indication_hl, which
does not include the bitrate info as well as PCIe, for PCIe, it use
function ath10k_htt_rx_h_rates to parse the bitrate info in struct
rx_ppdu_start and then report it to mac80211 via ieee80211_rx_status.
SDIO does not have the same info as PCIe, then iw command can not get
the rx bitrate by "iw wlan0 station dump".
for example, it always show 6.0 MBit/s
localhost ~ # iw wlan0 link
Connected to 3c:28:6d:96:fd:69 (on wlan0)
SSID: kukui_test
freq: 5180
RX: 111800 bytes (595 packets)
TX: 35419 bytes (202 packets)
signal: -41 dBm
rx bitrate: 6.0 MBit/s
This patch is to send WMI_TLV_REQUEST_PEER_STATS_INFO_CMDID to firmware
for ath10k_sta_statistics and save the rx bitrate for WMI event
WMI_TLV_PEER_STATS_INFO_EVENTID.
This patch only effect SDIO chip, ath10k_mac_sta_get_peer_stats_info
has check for bitrate_statistics of hw_params, this patch only enable
it for "qca6174 hw3.2 sdio".
Tested with QCA6174 SDIO firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-3-wgong@codeaurora.org
|
|
For wmi tlv type, firmware disable peer stats info by default, after
enable it, firmware will report WMI_TLV_PEER_STATS_INFO_EVENTID if
ath10k send WMI_TLV_REQUEST_PEER_STATS_INFO_CMDID to firmware.
Enable it will only set a flag in firmware, firmware will not report
it without receive request WMI command.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-2-wgong@codeaurora.org
|
|
When tx complete is disabled, all tx status will be set with status
HTT_TX_COMPL_STATE_ACK and indicate to mac80211 by ieee80211_tx_status,
then it does not have the statistics for retries and failed packets.
count of tx retries and tx failed of command "iw wlan0 station dump"
are both 0. If tx complete is not disabled, then firmware report the
tx status and ath10k indicate the status to mac80211, then mac80211
save the statistics and command "iw wlan0 station dump" show them.
for example:
localhost ~ # iw dev wlan0 station dump
Station 3c:28:6d:96:fd:69 (on wlan0)
inactive time: 5 ms
rx bytes: 1325012
rx packets: 6477
tx bytes: 85264
tx packets: 518
tx retries: 0
tx failed: 0
This patch only effect chips with tx complete disabled, e.g. SDIO.
with this patch, output of command "iw dev wlan0 station dump":
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 608 ms
rx bytes: 180366
rx packets: 991
tx bytes: 98765577
tx packets: 64624
tx retries: 14682
tx failed: 47086
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423024134.10601-1-wgong@codeaurora.org
|
|
When run command "iw dev wlan0 station dump", the rx duration is 0.
When firmware indicate WMI_UPDATE_STATS_EVENTID, extended flag of
statsis not set by default, so firmware do not report rx duration.
one sample:
localhost # iw wlan0 station dump
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 48 ms
rx bytes: 21670
rx packets: 147
tx bytes: 11529
tx packets: 100
tx retries: 88
tx failed: 36
beacon loss: 1
beacon rx: 31
rx drop misc: 47
signal: -72 [-74, -75] dBm
signal avg: -71 [-74, -75] dBm
beacon signal avg: -71 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 0 us
This patch enable firmware's extened flag of stats by setting flag
WMI_TLV_STAT_PEER_EXTD of ar->fw_stats_req_mask which is set in
ath10k_core_init_firmware_features via WMI_REQUEST_STATS_CMDID.
After apply this patch, rx duration show value with the command:
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 883 ms
rx bytes: 44289
rx packets: 265
tx bytes: 10838
tx packets: 93
tx retries: 899
tx failed: 103
beacon loss: 0
beacon rx: 78
rx drop misc: 46
signal: -71 [-74, -76] dBm
signal avg: -70 [-74, -76] dBm
beacon signal avg: -70 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 358004 us
This patch do not have side effect for all chips, because function
ath10k_debug_fw_stats_request is already exported to debugfs
"fw_stats" and WMI_REQUEST_STATS_CMDID is safely sent after condition
checked by ath10k_peer_stats_enabled in ath10k_sta_statistics.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423022758.5365-1-wgong@codeaurora.org
|
|
sdio chip use DMA buffer to receive TX packet from ath10k, and it has
limitation of each buffer, if the packet size exceed the credit size,
it will trigger error in firmware.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422084719.3479-1-wgong@codeaurora.org
|
|
The driver is allowing the invalid tx/rx chainmask configuration
(other than 1,3,7,15) set by the user. It causes the firmware
crash due to the invalid chainmask values.
Hence, reject the invalid chainmask values in the driver by not
sending the pdev set command to the firmware.
Tested hardware: QCA9888
Tested firmware: 10.4-3.10-00047
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587495512-29813-1-git-send-email-mkenna@codeaurora.org
|
|
When station connected to AP, and run TX traffic such as TCP/UDP, and
system enter suspend state, then mac80211 call ath10k_flush with set
drop flag, recently it only send wmi peer flush to firmware and
firmware will flush all pending TX packets, for PCIe, firmware will
indicate the TX packets status to ath10k, and then ath10k indicate to
mac80211 TX complete with the status, then all the packets has been
flushed at this moment. For SDIO chip, it is different, its TX
complete indication is disabled by default, and it has a tx queue in
ath10k, and its tx credit control is enabled, total tx credit is 96,
when its credit is not sufficient, then the packets will buffered in
the tx queue of ath10k, max packets is TARGET_TLV_NUM_MSDU_DESC_HL
which is 1024, for SDIO, when mac80211 call ath10k_flush with set drop
flag, maybe it have pending packets in tx queue of ath10k, and if it
does not have sufficient tx credit, the packets will stay in queue
untill tx credit report from firmware, if it is a noisy environment,
tx speed is low and the tx credit report from firmware will delay more
time, then the num_pending_tx will remain > 0 untill all packets send
to firmware. After the 1st ath10k_flush, mac80211 will call the 2nd
ath10k_flush without set drop flag immediately, then it will call to
ath10k_mac_wait_tx_complete, and it wait untill num_pending_tx become
to 0, in noisy environment, it is esay to wait about near 5 seconds,
then it cause the suspend take long time.
1st and 2nd callstack of ath10k_flush
[ 303.740427] ath10k_sdio mmc1:0001:1: ath10k_flush drop:1, pending:0-0
[ 303.740495] ------------[ cut here ]------------
[ 303.740739] WARNING: CPU: 1 PID: 3921 at /mnt/host/source/src/third_party/kernel/v4.19/drivers/net/wireless/ath/ath10k/mac.c:7025 ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.740757] Modules linked in: bridge stp llc ath10k_sdio ath10k_core rfcomm uinput cros_ec_rpmsg mtk_seninf mtk_cam_isp mtk_vcodec_enc mtk_fd mtk_vcodec_dec mtk_vcodec_common mtk_dip mtk_mdp3 videobuf2_dma_contig videobuf2_memops v4l2_mem2mem videobuf2_v4l2 videobuf2_common hid_google_hammer hci_uart btqca bluetooth dw9768 ov8856 ecdh_generic ov02a10 v4l2_fwnode mtk_scp mtk_rpmsg rpmsg_core mtk_scp_ipi ipt_MASQUERADE fuse iio_trig_sysfs cros_ec_sensors_ring cros_ec_sensors_sync cros_ec_light_prox cros_ec_sensors industrialio_triggered_buffer
[ 303.740914] kfifo_buf cros_ec_activity cros_ec_sensors_core lzo_rle lzo_compress ath mac80211 zram cfg80211 joydev [last unloaded: ath10k_core]
[ 303.741009] CPU: 1 PID: 3921 Comm: kworker/u16:10 Tainted: G W 4.19.95 #2
[ 303.741027] Hardware name: MediaTek krane sku176 board (DT)
[ 303.741061] Workqueue: events_unbound async_run_entry_fn
[ 303.741086] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 303.741166] pc : ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.741244] lr : ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.741260] sp : ffffffdf080e77a0
[ 303.741276] x29: ffffffdf080e77a0 x28: ffffffdef3730040
[ 303.741300] x27: ffffff907c2240a0 x26: ffffffde6ff39afc
[ 303.741321] x25: ffffffdef3730040 x24: ffffff907bf61018
[ 303.741343] x23: ffffff907c2240a0 x22: ffffffde6ff39a50
[ 303.741364] x21: 0000000000000001 x20: ffffffde6ff39a50
[ 303.741385] x19: ffffffde6bac2420 x18: 0000000000017200
[ 303.741407] x17: ffffff907c24a000 x16: 0000000000000037
[ 303.741428] x15: ffffff907b49a568 x14: ffffff907cf332c1
[ 303.741476] x13: 00000000000922e4 x12: 0000000000000000
[ 303.741497] x11: 0000000000000001 x10: 0000000000000007
[ 303.741518] x9 : f2256b8c1de4bc00 x8 : f2256b8c1de4bc00
[ 303.741539] x7 : ffffff907ab5e764 x6 : 0000000000000000
[ 303.741560] x5 : 0000000000000080 x4 : 0000000000000001
[ 303.741582] x3 : ffffffdf080e74a8 x2 : ffffff907aa91244
[ 303.741603] x1 : ffffffdf080e74a8 x0 : 0000000000000024
[ 303.741624] Call trace:
[ 303.741701] ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.741941] __ieee80211_flush_queues+0x1dc/0x358 [mac80211]
[ 303.742098] ieee80211_flush_queues+0x34/0x44 [mac80211]
[ 303.742253] ieee80211_set_disassoc+0xc0/0x5ec [mac80211]
[ 303.742399] ieee80211_mgd_deauth+0x720/0x7d4 [mac80211]
[ 303.742535] ieee80211_deauth+0x24/0x30 [mac80211]
[ 303.742720] cfg80211_mlme_deauth+0x250/0x3bc [cfg80211]
[ 303.742849] cfg80211_mlme_down+0x90/0xd0 [cfg80211]
[ 303.742971] cfg80211_disconnect+0x340/0x3a0 [cfg80211]
[ 303.743087] __cfg80211_leave+0xe4/0x17c [cfg80211]
[ 303.743203] cfg80211_leave+0x38/0x50 [cfg80211]
[ 303.743319] wiphy_suspend+0x84/0x5bc [cfg80211]
[ 303.743335] dpm_run_callback+0x170/0x304
[ 303.743346] __device_suspend+0x2dc/0x3e8
[ 303.743356] async_suspend+0x2c/0xb0
[ 303.743370] async_run_entry_fn+0x48/0xf8
[ 303.743383] process_one_work+0x304/0x604
[ 303.743394] worker_thread+0x248/0x3f4
[ 303.743403] kthread+0x120/0x130
[ 303.743416] ret_from_fork+0x10/0x18
[ 303.743812] ath10k_sdio mmc1:0001:1: ath10k_flush drop:0, pending:0-0
[ 303.743858] ------------[ cut here ]------------
[ 303.744057] WARNING: CPU: 1 PID: 3921 at /mnt/host/source/src/third_party/kernel/v4.19/drivers/net/wireless/ath/ath10k/mac.c:7025 ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.744075] Modules linked in: bridge stp llc ath10k_sdio ath10k_core rfcomm uinput cros_ec_rpmsg mtk_seninf mtk_cam_isp mtk_vcodec_enc mtk_fd mtk_vcodec_dec mtk_vcodec_common mtk_dip mtk_mdp3 videobuf2_dma_contig videobuf2_memops v4l2_mem2mem videobuf2_v4l2 videobuf2_common hid_google_hammer hci_uart btqca bluetooth dw9768 ov8856 ecdh_generic ov02a10 v4l2_fwnode mtk_scp mtk_rpmsg rpmsg_core mtk_scp_ipi ipt_MASQUERADE fuse iio_trig_sysfs cros_ec_sensors_ring cros_ec_sensors_sync cros_ec_light_prox cros_ec_sensors industrialio_triggered_buffer kfifo_buf cros_ec_activity cros_ec_sensors_core lzo_rle lzo_compress ath mac80211 zram cfg80211 joydev [last unloaded: ath10k_core]
[ 303.744256] CPU: 1 PID: 3921 Comm: kworker/u16:10 Tainted: G W 4.19.95 #2
[ 303.744273] Hardware name: MediaTek krane sku176 board (DT)
[ 303.744301] Workqueue: events_unbound async_run_entry_fn
[ 303.744325] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 303.744403] pc : ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.744480] lr : ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.744496] sp : ffffffdf080e77a0
[ 303.744512] x29: ffffffdf080e77a0 x28: ffffffdef3730040
[ 303.744534] x27: ffffff907c2240a0 x26: ffffffde6ff39afc
[ 303.744556] x25: ffffffdef3730040 x24: ffffff907bf61018
[ 303.744577] x23: ffffff907c2240a0 x22: ffffffde6ff39a50
[ 303.744598] x21: 0000000000000000 x20: ffffffde6ff39a50
[ 303.744620] x19: ffffffde6bac2420 x18: 000000000001831c
[ 303.744641] x17: ffffff907c24a000 x16: 0000000000000037
[ 303.744662] x15: ffffff907b49a568 x14: ffffff907cf332c1
[ 303.744683] x13: 00000000000922ea x12: 0000000000000000
[ 303.744704] x11: 0000000000000001 x10: 0000000000000007
[ 303.744747] x9 : f2256b8c1de4bc00 x8 : f2256b8c1de4bc00
[ 303.744768] x7 : ffffff907ab5e764 x6 : 0000000000000000
[ 303.744789] x5 : 0000000000000080 x4 : 0000000000000001
[ 303.744810] x3 : ffffffdf080e74a8 x2 : ffffff907aa91244
[ 303.744831] x1 : ffffffdf080e74a8 x0 : 0000000000000024
[ 303.744853] Call trace:
[ 303.744929] ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.745098] __ieee80211_flush_queues+0x1dc/0x358 [mac80211]
[ 303.745277] ieee80211_flush_queues+0x34/0x44 [mac80211]
[ 303.745424] ieee80211_set_disassoc+0x108/0x5ec [mac80211]
[ 303.745569] ieee80211_mgd_deauth+0x720/0x7d4 [mac80211]
[ 303.745706] ieee80211_deauth+0x24/0x30 [mac80211]
[ 303.745853] cfg80211_mlme_deauth+0x250/0x3bc [cfg80211]
[ 303.745979] cfg80211_mlme_down+0x90/0xd0 [cfg80211]
[ 303.746103] cfg80211_disconnect+0x340/0x3a0 [cfg80211]
[ 303.746219] __cfg80211_leave+0xe4/0x17c [cfg80211]
[ 303.746335] cfg80211_leave+0x38/0x50 [cfg80211]
[ 303.746452] wiphy_suspend+0x84/0x5bc [cfg80211]
[ 303.746467] dpm_run_callback+0x170/0x304
[ 303.746477] __device_suspend+0x2dc/0x3e8
[ 303.746487] async_suspend+0x2c/0xb0
[ 303.746498] async_run_entry_fn+0x48/0xf8
[ 303.746510] process_one_work+0x304/0x604
[ 303.746521] worker_thread+0x248/0x3f4
[ 303.746530] kthread+0x120/0x130
[ 303.746542] ret_from_fork+0x10/0x18
one sample's debugging log: it wait 3190 ms(5000 - 1810).
1st ath10k_flush, it has 120 packets in tx queue of ath10k:
<...>-1513 [000] .... 25374.786005: ath10k_log_err: ath10k_sdio mmc1:0001:1 ath10k_flush drop:1, pending:120-0
<...>-1513 [000] ...1 25374.788375: ath10k_log_warn: ath10k_sdio mmc1:0001:1 ath10k_htt_tx_mgmt_inc_pending htt->num_pending_mgmt_tx:0
<...>-1500 [001] .... 25374.790143: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:121
2st ath10k_flush, it has 121 packets in tx queue of ath10k:
<...>-1513 [000] .... 25374.790571: ath10k_log_err: ath10k_sdio mmc1:0001:1 ath10k_flush drop:0, pending:121-0
<...>-1513 [000] .... 25374.791990: ath10k_log_err: ath10k_sdio mmc1:0001:1 ath10k_mac_wait_tx_complete state:1 pending:121-0
<...>-1508 [001] .... 25374.792696: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:46
<...>-1508 [001] .... 25374.792700: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:46
<...>-1508 [001] .... 25374.792729: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:121
<...>-1508 [001] .... 25374.792937: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:88, count:32, len:49792
<...>-1508 [001] .... 25374.793031: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:75, count:14, len:21784
kworker/u16:0-25773 [003] .... 25374.793701: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:46
<...>-1881 [000] .... 25375.073178: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:24
<...>-1881 [000] .... 25375.073182: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:24
<...>-1881 [000] .... 25375.073429: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:75
<...>-1879 [001] .... 25375.074090: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:24
<...>-1881 [000] .... 25375.074123: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:51, count:24, len:37344
<...>-1879 [001] .... 25375.270126: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:26
<...>-1879 [001] .... 25375.270130: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:26
<...>-1488 [000] .... 25375.270174: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:51
<...>-1488 [000] .... 25375.270529: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:25, count:26, len:40456
<...>-1879 [001] .... 25375.270693: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:26
<...>-1488 [001] .... 25377.775885: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:12
<...>-1488 [001] .... 25377.775890: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:12
<...>-1488 [001] .... 25377.775933: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:25
<...>-1488 [001] .... 25377.776059: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:13, count:12, len:18672
<...>-1879 [001] .... 25377.776100: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:12
<...>-1488 [001] .... 25377.878079: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:15
<...>-1488 [001] .... 25377.878087: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:15
<...>-1879 [000] .... 25377.878323: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:13
<...>-1879 [000] .... 25377.878487: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:0, count:13, len:20228
<...>-1879 [000] .... 25377.878497: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:13
<...>-1488 [001] .... 25377.919927: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:11
<...>-1488 [001] .... 25377.919932: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:13
<...>-1488 [001] .... 25377.919976: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:0
<...>-1881 [000] .... 25377.982645: ath10k_log_warn: ath10k_sdio mmc1:0001:1 HTT_T2H_MSG_TYPE_MGMT_TX_COMPLETION status:0
<...>-1513 [001] .... 25377.982973: ath10k_log_err: ath10k_sdio mmc1:0001:1 ath10k_mac_wait_tx_complete time_left:1810, pending:0-0
Flush all pending TX packets for the 1st ath10k_flush reduced the wait
time of the 2nd ath10k_flush and then suspend take short time.
This Patch only effect SDIO chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200415233730.10581-1-wgong@codeaurora.org
|
|
The default credit size is 1792 bytes, but the IP mtu is 1500 bytes,
then it has about 290 bytes's waste for each data packet on sdio
transfer path for TX bundle, it will reduce the transmission utilization
ratio for data packet.
This patch enable the small credit size in firmware, firmware will use
the new credit size 1556 bytes, it will increase the transmission
utilization ratio for data packet on TX patch. It results in significant
performance improvement on TX path.
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410061400.14231-3-wgong@codeaurora.org
|
|
The transmission utilization ratio for sdio bus for small packet is
slow, because the space and time cost for sdio bus is same for large
length packet and small length packet. So the speed of data for large
length packet is higher than small length.
Test result of different length of data:
data packet(byte) cost time(us) calculated rate(Mbps)
256 28 73
512 33 124
1024 35 234
1792 45 318
14336 168 682
28672 333 688
57344 660 695
This patch change the TX packet from single packet to a large length
bundle packet, max size is 32, it results in significant performance
improvement on TX path.
Also there's a fourth thread "ath10k_tx_complete_wq" added to ath10k as it
improves TCP RX throughput (values in Mbps):
TCP-RX TCP-TX UDP-RX UDP-TX
use workqueue_tx_complete 423 357 448 412
change it to ar->workqueue 410 360 449 414
change it to ar->workqueue_aux 405 339 446 401
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
It only enable bundle for sdio chip.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410061400.14231-2-wgong@codeaurora.org
|
|
That way we don't need to have an empty function in sdio.c.
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587037859-28873-5-git-send-email-kvalo@codeaurora.org
|
|
The _hif_ prefix should be used only on functions part of ath10k_hif_ops, so
remove it from functions which should not have it.
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587037859-28873-4-git-send-email-kvalo@codeaurora.org
|
|
This patch is to set register to allow the mbox enter sleep status
if it does not have tx traffic and wakeup it if tx traffic arrive.
After mbox enter sleep status, the soc will enter sleep status by
firmware, this will save power. The power consume drops from about
90mW to about 10mW with this patch.
This patch only effect sdio chip.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587037859-28873-3-git-send-email-kvalo@codeaurora.org
|
|
Convert ath10k_hif_swap_mailbox() to a more generic op so that bus drivers can
do more than just swap the mailbox, for example set power save settings like in
the following sdio patch.
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587037859-28873-2-git-send-email-kvalo@codeaurora.org
|
|
Fix some typo:
s/fnrom/from
s/pkgs/pkts/
s/AMSUs/AMSDUs/
Signed-off-by: Mamatha Telu <telumamatha36@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586715875-5182-1-git-send-email-telumamatha36@gmail.com
|
|
ath.git patches for v5.8. Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
|
|
sdio bus bandwidth is low, sometimes for high performance TX test,
it will lack of ath10k_sdio_bus_request, it will print message:
ath10k_sdio mmc1:0001:1: unable to allocate bus request for async request
change the num from 64 to 1024 will not happen it.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200212080415.31265-3-wgong@codeaurora.org
|
|
For sdio chip, it is high latency bus, all the TX packet's content will
be tranferred from HOST memory to firmware memory via sdio bus, then it
need much more memory in firmware than low latency bus chip, for low
latency chip, such as PCI-E, it only need to transfer the TX descriptor
via PCI-E bus to firmware memory. For sdio chip, reduce the complexity of
TX logic will help TX efficiency since its memory is limited, and it will
reduce the TX circle's time of each packet and then firmware will have more
memory for TX since TX complete also need memeory.
This patch disable TX complete indication from firmware for htt data
packet, it will not have TX complete indication from firmware to ath10k.
It will cut the cost of bus bandwidth of TX complete and make the TX
logic of firmware simpler, it results in significant performance
improvement on TX path.
Udp TX throughout is 130Mbps without this patch, and it arrives
400Mbps with this patch.
The downside of this patch is the command "iw wlan0 station dump" will
show 0 for "tx retries" and "tx failed" since all tx packet's status
is success.
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200212080415.31265-2-wgong@codeaurora.org
|
|
Currently sta airtime is updated without any lock in case of
host based airtime calculation. Which may result in accessing the
invalid sta pointer in case of continuous station connect/disconnect.
This patch fix the kernel null pointer dereference by updating the
station airtime with proper RCU lock in case of host based airtime
calculation.
Proceeding with the analysis of "ARM Kernel Panic".
The APSS crash happened due to OOPS on CPU 0.
Crash Signature : Unable to handle kernel NULL pointer dereference
at virtual address 00000300
During the crash,
PC points to "ieee80211_sta_register_airtime+0x1c/0x448 [mac80211]"
LR points to "ath10k_txrx_tx_unref+0x17c/0x364 [ath10k_core]".
The Backtrace obtained is as follows:
[<bf880238>] (ieee80211_sta_register_airtime [mac80211]) from
[<bf945a38>] (ath10k_txrx_tx_unref+0x17c/0x364 [ath10k_core])
[<bf945a38>] (ath10k_txrx_tx_unref [ath10k_core]) from
[<bf9428e4>] (ath10k_htt_txrx_compl_task+0xa50/0xfc0 [ath10k_core])
[<bf9428e4>] (ath10k_htt_txrx_compl_task [ath10k_core]) from
[<bf9b9bc8>] (ath10k_pci_napi_poll+0x50/0xf8 [ath10k_pci])
[<bf9b9bc8>] (ath10k_pci_napi_poll [ath10k_pci]) from
[<c059e3b0>] (net_rx_action+0xac/0x160)
[<c059e3b0>] (net_rx_action) from [<c02329a4>] (__do_softirq+0x104/0x294)
[<c02329a4>] (__do_softirq) from [<c0232b64>] (run_ksoftirqd+0x30/0x90)
[<c0232b64>] (run_ksoftirqd) from [<c024e358>] (smpboot_thread_fn+0x25c/0x274)
[<c024e358>] (smpboot_thread_fn) from [<c02482fc>] (kthread+0xd8/0xec)
Tested HW: QCA9888
Tested FW: 10.4-3.10-00047
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585736290-17661-1-git-send-email-vnaralas@codeaurora.org
|
|
Enable radar detection in secondary segment for VHT160 and VHT80+80 mode
on DFS channels. Otherwise, when injecting radar pulse in the secondary
segment, the DUT can't detect radar pulse.
Tested: qca9984 with firmware ver 10.4-3.10-00047
Signed-off-by: Lei Wang <leiwa@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585574792-719-2-git-send-email-ssreeela@codeaurora.org
|
|
Set right channel frequencies in VHT160 mode according to the VHT160
interoperability workaround added as part of IEEE Std 802.11™-2016 in
"Table 9-252—VHT Operation Information subfields", band_center_freq2
corresponds to CCFS1 in Table 9-253. Previous implementation
(band_center_freq2 = 0 for VHT160) is only deprecated.
Enable VHT80+80 mode and set the proper peer RX nss value for VHT160 and
VHT80+80 mode.
Based on patches by Sebastian Gottschall:
https://lkml.kernel.org/r/20180704095444.662-1-s.gottschall@dd-wrt.com
https://lkml.kernel.org/r/20180704120519.6479-1-s.gottschall@dd-wrt.com
Tested: qca9984 with firmware ver 10.4-3.10-00047
Co-developed-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-developed-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Lei Wang <leiwa@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585574792-719-1-git-send-email-ssreeela@codeaurora.org
|
|
There is a race condition, when the user writes 'hw-restart' and
'hard' in the simulate_fw_crash debugfs file without any delay.
In the above scenario, the firmware dump work queue(scheduled by
'hard') should be handled gracefully, while the target is in the
'hw-restart'.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00044
Co-developed-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585213077-28439-1-git-send-email-mkenna@codeaurora.org
|
|
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
|
|
GCMP MIC length is not filled for GCMP/GCMP-256 cipher suites in
PMF enabled case. Due to mismatch in MIC length, deauth/disassoc frames
are unencrypted.
This patch fills proper MIC length for GCMP/GCMP-256 cipher suites.
Tested HW: QCA9984, QCA9888
Tested FW: 10.4-3.6-00104
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath.git patches for v5.7. Major changes:
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
|
|
Hardwares tested : QCA9887
Firmwares tested : 10.4-3.9.0.1-00036
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The tid of 11a station with WMM disable reported by FW is 0x10 in
tx completion. The tid 16 is mapped to a NULL txq since buffer
MMPDU capbility is not supported. Then 11a station's airtime will
not be registered due to NULL txq check. As a results, airtime of
11a station keeps unchanged in debugfs system.
Mask the tid along with IEEE80211_QOS_CTL_TID_MASK to make it in
the valid range.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.10-00047
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|