| Age | Commit message (Collapse) | Author |
|---|
|
Configure pause time to 0xffff when tx flow control enabled
Set pause time to 0xffff in the pause frame to indicate the
partner to stop sending the packets. When RX buffer frees up,
the device sends pause frame with pause time zero for partner to
resume transmission.
Fixes: 2f7ca802bdae ("Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change enables the use of SW timestamping on Raspberry PI.
smsc95xx uses the usbnet transmit function usbnet_start_xmit(), which
implements software timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE
capability was missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced.
By using ethtool_op_get_ts_info() as get_ts_info() also the
SOF_TIMESTAMPING_TX_SOFTWARE is announced.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When TX checksum offload is used, if the computed checksum is 0 the
LAN95xx device do not alter the checksum to 0xffff. In the case of ipv4
UDP checksum, it indicates to receiver that no checksum is calculated.
Under ipv6, UDP checksum yields a result of zero must be changed to
0xffff. Hence disabling checksum offload for ipv6 packets.
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Reported-by: popcorn mix <popcornmix@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both conflict were simple overlapping changes.
In the kaweth case, Eric Dumazet's skb_cow() bug fix overlapped the
conversion of the driver in net-next to use in-netdev stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver was failing to check that the SKB wasn't cloned
before adding checksum data.
Replace existing handling to extend/copy the header buffer
with skb_cow_head.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This chip is used by a lot of embedded devices and also by the Raspberry
Pi 1, 2 & 3 which were created to promote the study of computer
sciences. Students wanting to learn kernel / network device driver
programming through those devices can only rely on the Linux kernel
driver source to make their own.
This commit adds a lot of comments to the registers definition to expand
the register names.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: Martin Wetterwald <martin@wetterwald.eu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the net stats64 counters to the usbnet core. With that
in place put the hooks into every usbnet driver to use it.
This is a strait forward addition of 64bit counters for RX and TX packet
and byte counts. It is done in the same style as for the other net drivers
that support stats64. Note that the other stats fields remain as 32bit
sized values (error counts, etc).
The motivation to add this is that it is not particularly difficult to
get the RX and TX byte counts to wrap on 32bit platforms.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add mdix control through ethtool.
Signed-off-by: Woojung Huh <Woojung.huh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To detect link status up/down for connections where autonegotiation is
explicitly disabled, we don't get an irq but need to poll the status
register for link up/down detection.
This patch adds a workqueue to poll for link status.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the call to fn() fails then "buf" is uninitialized. Just return the
error code in that case.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This takes the MAC address for smsc75xx/smsc95xx USB network devices
from a the device tree. This is required to get a usable persistent
address on the popular beagleboard, whose hardware designers
accidentally forgot that an ethernet device really requires an a
MAC address to be functional.
The Raspberry Pi also ships smsc9514 without a serial EEPROM, stores
the MAC address in ROM accessible via VC4 firmware.
The smsc75xx and smsc95xx drivers are just two copies of the
same code, so better fix both.
[lkundrak@v3.sk: updated to use of_get_property() as per suggestion from
Arnd, reworded the message and comments a bit]
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb->len is always non-negative.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
we were dereferencing dev to initialize pdata. but just after that we
have a BUG_ON(!dev). so we were basically dereferencing the pointer
first and then tesing it for NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The smsc95xx needs to resume with reset operation. Otherwise it causes
system hang by network error like below after resume. This case appears
on odroid u3 board.
[ 9.727600] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727648] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727689] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727728] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.729486] PM: resume of devices complete after 2011.219 msecs
[ 10.117609] Restarting tasks ... done.
[ 11.725099] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 13.480846] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 13.481361] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
...
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.
One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.
With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.
The bug has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=29082
This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
callback function that could be affected by this change.
These extra checks could possibly be removed by someone
who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
dev->done list to queue skbs for cleanup.
The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Oliver Neukum <oliver@neukum.org>
CC: Steve Glendinning <steve.glendinning@shawell.net>
CC: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If suspend callback fails in system sleep context, usb core will
ignore the failure and let system sleep go ahead further, so
this patch doesn't recover device under this situation.
Also add comments on the case.
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The name of FEATURE_AUTOSUSPEND is very misleading and the actual
meaning is remote wakeup, but a device incapable of remote wakeup
still can support USB autosuspend under some situations, so rename
it to avoid misunderstanding.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b2d4b150(smsc95xx: enable dynamic autosuspend) implements
autosuspend, but breaks current runtime suspend, such as:
when the interface becomes down, the usb device can't be put into
runtime suspend any more.
This patch fixes the broken runtime suspend.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The three below functions:
smsc95xx_enter_suspend0()
smsc95xx_enter_suspend1()
smsc95xx_enter_suspend2()
return > 0 in case of success, so they will cause smsc95xx_suspend()
to return > 0 and cause suspend failure.
The bug is introduced in commit 3b9f7d(smsc95xx: fix error handling
in suspend failure case).
Cc: <stable@vger.kernel.org> [3.8]
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables USB dynamic autosuspend for LAN9500A. This
saves very little power in itself, but it allows power saving
in upstream hubs/hosts.
The earlier devices in this family (LAN9500/9512/9514) do not
support this feature.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The register read/write functions already log a warning if
an access fails, so this patch removes the additional warnings
logged by callers that don't add any more information.
This patch makes the resulting driver smaller by not containing
as many warning strings.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a missing endian conversion which results in the
interface failing to come up on BE platforms.
It also removes an unnecessary pointer dereference from this
function.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the ethtool register dump for smsc95xx to dump
all 4 bytes of the final register (COE_CR) instead of just the
first byte.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These macros, while reducing the amount of code, hide flow control
and make the code more confusing to follow and review. This patch
expands them. It should have no functional effect on the driver.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a bug introduced in bbd9f9e which could prevent
some wakeups from working correctly if multiple wol options were
selected.
This helper function calculates a 16-bit crc and shifts it into
either the high or low 16 bits of a u32 so the caller can or it
directly into place. The function previously had a u16 return
type so would always have returned zero when filter was odd.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Reported-by: Bjorn Mork <bjorn@mork.no>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As pointed out by Bjorn Mork, the generic "usb" driver sets this
for us so no need to directly set it in this driver.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Cc: Bjorn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch ensures that if we fail to suspend the LAN9500 device
we call usbnet_resume before returning failure, instead of
leaving the usbnet driver in an unusable state.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a buffer overflow introduced by bbd9f9e, where
the filter_mask array is accessed beyond its bounds.
Updated to also add a check for kzalloc failure, as reported by
Bjorn Mork and Joe Perches.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Cc: Bjorn Mork <bjorn@mork.no>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid any possible message logging interleaving by adding
missing newlines.
Align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch splits out the logic for entering suspend modes
to separate functions, to reduce the complexity of the
smsc95xx_suspend function.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables LAN9500 family devices to wake from suspend
on either link up or link down events
It also adds _nopm versions of mdio access functions, so we can
safely call them from suspend and resume functions
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of storing the number of wake-up frame filter registers
in the pdata structure, this patch changes the driver to detect
the type of device we have and store its available features.
The new two features will be used in future patches.
This patch is intended to have no change in behaviour.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
without this patch the two lines below won't ever execute
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor line offset auto-merges.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device datasheet specifies the BUSY bit must be set when reading
or writing phy registers. This patch ensures we do that.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch applies the introduced usbnet_read_cmd_nopm() and
usbnet_write_cmd_nopm() in the callback of resume and suspend
to avoid deadlock if USB runtime PM is considered into
usbnet_read_cmd() and usbnet_write_cmd().
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes memory leak in smsc95xx_suspend.
Also, it isn't necessary to bother mm to allocate 8bytes/16byte,
and we can use stack variable safely.
Acked-By: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
f7b2927 introduced tx checksum offload support for smsc95xx,
and enabled it by default. This feature doesn't take
endianness into account, so causes most tx to fail on
those platforms.
This patch fixes the problem fully by adding the missing
conversion.
An alternate workaround is to disable TX checksum offload
on those platforms. The cpu impact of this feature is very low.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for wol wakeup on unicast, broadcast,
multicast and arp frames.
The wakeup filter code isn't pretty, but it works.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables wake from system suspend on magic packet.
Patch updated to replace BUG_ON with WARN_ON_ONCE and return.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables the device to enter its lowest power SUSPEND2
state during system suspend, instead of staying up using full power.
Patch updated to not add two pointers to .suspend & .resume.
Patch updated to replace BUG_ON with WARN_ON_ONCE and return.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes an issue on some systems, where after suspend the
link is re-established but the ethernet interface does not resume.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds additional checks of the values returned by
smsc95xx_(read|write)_reg, and wraps their common patterns
in macros.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removes unnecessary variables as smsc95xx_write_reg takes its
value by parameter. Early versions passed this parameter by
reference.
Also replace hardcoded interrupt status value with a #define
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
