| Age | Commit message (Collapse) | Author |
|---|
|
Add support for the net stats64 counters to the usbnet core. With that
in place put the hooks into every usbnet driver to use it.
This is a strait forward addition of 64bit counters for RX and TX packet
and byte counts. It is done in the same style as for the other net drivers
that support stats64. Note that the other stats fields remain as 32bit
sized values (error counts, etc).
The motivation to add this is that it is not particularly difficult to
get the RX and TX byte counts to wrap on 32bit platforms.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of bug fixes in 'net' overlapping other changes in
'net-next-.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for Cypress GX3 SuperSpeed to Gigabit Ethernet
Bridge Controller (Vendor=04b4 ProdID=3610).
Patch verified on x64 linux kernel 4.7.4, 4.8.6, 4.9-rc4 systems
with the Kensington SD4600P USB-C Universal Dock with Power,
which uses the Cypress GX3 SuperSpeed to Gigabit Ethernet Bridge
Controller.
A similar patch was signed-off and tested-by Allan Chou
<allan@asix.com.tw> on 2015-12-01.
Allan verified his similar patch on x86 Linux kernel 4.1.6 system
with Cypress GX3 SuperSpeed to Gigabit Ethernet Bridge Controller.
Tested-by: Allan Chou <allan@asix.com.tw>
Tested-by: Chris Roth <chris.roth@usask.ca>
Tested-by: Artjom Simon <artjom.simon@gmail.com>
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Chris Roth <chris.roth@usask.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
usbnet:
- Remove stale new_mtu <= 0 check in usbnet.c
- Set min_mtu = 0, max_mtu = 65535 (sub-drivers must set their own
max_mtu and/or min_mtu as needed)
r8152:
- Set appropriate max_mtu for different variants (1500 or 9194)
lan78xx:
- Set max_mtu = 9000
asix_driver:
- max_mtu = 16384 for ax88178 variant
ax88179:
- max_mtu = 4088
cdc_ncm:
- max_mtu from hardware
cdc-phonet:
- min_mtu = 6, max_mtu = 65541
sierra_net:
- max_mtu = 1500, call usbnet_change_mtu directly
- sierra_net_change_mtu checked for MTU > 1500, then called
usbnet_change_mtu, but if we set max_mtu to let the network core handle
the range check, then we can simply call usbnet_change_mtu directly
smsc75xx:
- max_mtu = 9000
CC: netdev@vger.kernel.org
CC: Woojung Huh <woojung.huh@microchip.com>
CC: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
CC: Hayes Wang <hayeswang@realtek.com>
CC: Oliver Neukum <oneukum@suse.com>
CC: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following patch fixes a bug which causes the ax88179_178a driver to be
incapable of being added to a bond.
When I brought up the issue with the bonding maintainers, they indicated
that the real problem was with the NIC driver which must return zero for
success (of setting the MAC address). I see that several other NIC drivers
follow that pattern by either simply always returing zero, or by passing
through a negative (error) result while rewriting any positive return code
to zero. With that same philisophy applied to the ax88179_178a driver, it
allows it to work correctly with the bonding driver.
I believe this is suitable for queuing in -stable, as it's a small, simple,
and obvious fix that corrects a defect with no other known workaround.
This patch is against vanilla 3.17(.0).
Signed-off-by: Ian Morgan <imorgan@primordial.ca>
drivers/net/usb/ax88179_178a.c | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add functions to support ethtool EEE manipulating, and the EEE
is disabled in default setting to enhance the compatibility
with certain switch.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are 4 USB fixes for your current tree.
Two of them are reverts to hopefully resolve the nasty XHCI
regressions we have been having on some types of devices. The other
two are quirks for some Logitech video devices"
* tag 'usb-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "USBNET: ax88179_178a: enable tso if usb host supports sg dma"
Revert "xhci 1.0: Limit arbitrarily-aligned scatter gather."
usb: Make DELAY_INIT quirk wait 100ms between Get Configuration requests
usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e
|
|
This reverts commit 3804fad45411b48233b48003e33a78f290d227c8.
This commit, together with commit 247bf557273dd775505fb9240d2d152f4f20d304
"xhci 1.0: Limit arbitrarily-aligned scatter gather." were
origially added to get xHCI 1.0 hosts and usb ethernet ax88179_178a devices
working together with scatter gather. xHCI 1.0 hosts pose some requirement on how transfer
buffers are aligned, setting this requirement for 1.0 hosts caused USB 3.0 mass
storage devices to fail more frequently.
USB 3.0 mass storage devices used to work before 3.14-rc1. Theoretically,
the TD fragment rules could have caused an occasional disk glitch.
Now the devices *will* fail, instead of theoretically failing.
>From a user perspective, this looks like a regression; the USB device obviously
fails on 3.14-rc1, and may sometimes silently fail on prior kernels.
The proper soluition is to implement the TD fragment rules for xHCI 1.0 hosts,
but for now, revert this patch until scatter gather can be properly supported.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the USB device ID for the D-Link DUB-1312 USB 3.0 to Gigabit Ethernet
Adapter to the AX88179/178A driver.
Signed-off-by: Gerry Demaret <gerry@tigron.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add VID:DID for Lenovo OneLinkDock Gigabit LAN
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.
One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.
With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.
The bug has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=29082
This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
callback function that could be affected by this change.
These extra checks could possibly be removed by someone
who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
dev->done list to queue skbs for cleanup.
The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Oliver Neukum <oliver@neukum.org>
CC: Steve Glendinning <steve.glendinning@shawell.net>
CC: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
register to avoid TX throttling
Remove AX_MEDIUM_ALWAYS_ONE in AX_MEDIUM_STATUS_MODE register.
Setting this bit may cause TX throttling in Half-Duplex mode.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add VID:DID for Samsung USB Ethernet Adapter.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct the definition of AX_RXHDR_CRC_ERR and
AX_RXHDR_DROP_ERR. They are BIT29 and BIT31 in pkt_hdr
seperately.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
|
|
This patch enables 'can_dma_sg' flag for ax88179_178a device
if the attached host controller supports building packet from
discontinuous buffers(DMA SG is possible), so TSO can be enabled
and skb fragment buffers can be passed to usb stack via urb->sg
directly.
With the patch, system CPU utilization decreased ~50% and throughput
increased by ~10% when doing iperf client test on one ARM A15 dual
core board.
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Grant Grundler <grundler@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Eric Dumazet <edumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ax88179_tx_fixup() has quite complex code trying to push 8 bytes
of control data (len/mss), but fails to do it properly for TCP packets,
incurring an extra copy and point of memory allocation failure.
Lets use the simple and approved way.
dev->needed_headroom being 8, all frames should have 8 bytes of
headroom, so the extra copy should be unlikely anyway.
This patch should improve performance for TCP xmits.
Reported-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge net into net-next to setup some infrastructure Eric
Dumazet needs for usbnet changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch centralizes computing of max rx/tx qlen, because:
- RX_QLEN()/TX_QLEN() is called in hot path
- computing depends on device's usb speed, now we have ls/fs, hs, ss,
so more checks need to be involved
- in fact, max rx/tx qlen should not only depend on device USB
speed, but also depend on ethernet link speed, so we need to
consider that in future.
- if SG support is done, max tx qlen may need change too
Generally, hard_mtu and rx_urb_size are changed in bind(), reset()
and link_reset() callback, and change mtu network operation, this
patches introduces the API of usbnet_update_max_qlen(), and calls
it in above path.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
usbnet doesn't support yet SG, so drivers should not advertise SG or TSO
capabilities, as they allow TCP stack to build large TSO packets that
need to be linearized and might use order-5 pages.
This adds an extra copy overhead and possible allocation failures.
Current code ignore skb_linearize() return code so crashes are even
possible.
Best is to not pretend SG/TSO is supported, and add this again when/if
usbnet really supports SG for devices who could get a performance gain.
Based on a prior patch from Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I tested with the AX88179 usb dongle, if without .reset_resume hook,
after S3/S4 resume you have to enable network interface or reload the
dirver module manually otherwise the network interface can not work.
Signed-off-by: David Chang <dchang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct a typo in description of driver_info, it should be Gigabit
Signed-off-by: David Chang <dchang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use usbnet_link_change to handle link change centrally.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a resubmission.
Added kfree() in ax88179_get_eeprom to prevent memory leakage.
Modified "__le16 rxctl" to "u16 rxctl" in "struct ax88179_data" and removed pointless casts.
Removed asix_init and asix_exit functions and added "module_usb_driver(ax88179_178a_driver)".
Fixed endianness issue on big endian systems and verified this driver on iBook G4.
Removed steps that change net->features in ax88179_set_features function.
Added "const" to ethtool_ops structure and fixed the coding style of AX88179_BULKIN_SIZE array.
Fixed the issue that the default MTU is not 1500.
Added ax88179_change_mtu function and enabled the hardware jumbo frame function to support an
MTU higher than 1500.
Fixed indentation and empty line coding style errors.
The _nopm version usb functions were added to access register in suspend and resume functions.
Serveral variables allocted dynamically were removed and replaced by stack variables.
ax88179_get_eeprom were modified from asix_get_eeprom in asix_common.
This patch adds a driver for ASIX's AX88179 family of USB 3.0/2.0
to gigabit ethernet adapters. It's based on the AX88xxx driver but
the usb commands used to access registers for AX88179 are completely different.
This driver had been verified on x86 system with AX88179/AX88178A and
Sitcomm LN-032 USB dongles.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
